In addition to shortening the function name, move the printk-call into the
function thereby saving some code lines. Also, make the function out_of_line
since it is not on a performance critical path. Finally, rename the reworked
function to ide_floppy..().
Bart:
- minor CodingStyle fixup
Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
By passing idefloppy_floppy_t *floppy to the factored out functions, we get
rid of (almost) all local vars so stack usage should be at minimum here. Also,
we merge idefloppy_begin_format() into idefloppy_format_start() since it is its
only user. Also, rename idefloppy_format_start() to idefloppy_format_unit().
Finally, rename the reworked functions to ide_floppy..().
Bart
- minor CodingStyle fixup
Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Also,
- remove the accompanying 4 byte idefloppy_capacity_header.
- rename functions from idefloppy_... to ide_floppy_... after cleanup.
- simplify loop in ide_floppy_get_capacity() by reversing if-test condition
logically.
- finally, fix white space and checkpatch.pl issues
Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
While at it, collapse idefloppy_analyze_error() into
idefloppy_request_sense_callback() since the latter was its only user.
Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This change is rather temporary and is in preparation of using generic commands
as is the case with ide-cd and the uniform cdrom layer (i.e. init_cdrom_command())
However, before this happens, we'll have to remove all typedefs and teach
idefloppy_create_mode_sense_cmd() to work directly on u8 buffers.
Also, since idefloppy_get_capability_page() was used to read only the sfrp bit,
rename the latter so that the name reflects what it does.
Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* some debug_log() calls were not using "ide-floppy: " prefix
* a few used printk levels different than KERN_INFO (KERN_NOTICE
and KERN_ERR, which is the default one if no level is given)
Bart:
- fix build issues for IDEFLOPPY_DEBUG_LOG set to 1 while at it
- s/__FUNCTION__/__func__/
Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There were two almost identical function names in ide-floppy.c, which makes
their distinction almost impossible. While ide_floppy_release() cleans up the
object after the last reference to it has been dropped, idefloppy_release() is
the blkdev .release method from struct block_device_operations which releases
that last reference.
Rename ide_floppy_release() to idefloppy_cleanup_obj() in order to make its
purpose more clear.
There should be no functionality change resulting from this patch.
Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This BUG_ON is unneeded since the ->handler != NULL check is performed in
ide_set_handler().
Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Replace the ide-floppy packet commands opcode defines with the generic ones.
Add a missing GPCMD_WRITE_12 (opcode 0xaa) to the generic ones in cdrom.h. The
last one can be found in the current version of INF-8090, p.905.
[ Bart: Tejun's libata patch also adding GPCMD_WRITE_12 got merged first ]
Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ->cable_detect method to ide_hwif_t.
* Call the new method in ide_init_port() if:
- the host supports UDMA modes > UDMA2 ('hwif->ultra_mask & 78')
- DMA initialization was successful (if hwif->dma_base is not set
ide_init_port() sets hwif->ultra_mask to zero)
- "idex=ata66" is not used ('hwif->cbl != ATA_CBL_PATA40_SHORT')
* Convert PCI host drivers to use ->cable_detect method.
While at it:
* Factor out cable detection to separate functions (if not already done).
* hpt366.c/it8213.c/slc90e66.c:
- don't check cable type if "idex=ata66" is used
* pdc202xx_new.c:
- add __devinit tag to pdcnew_cable_detect()
* pdc202xx_old.c:
- rename pdc202xx_old_cable_detect() to pdc2026x_old_cable_detect()
- add __devinit tag to pdc2026x_old_cable_detect()
Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove 'struct pci_dev *dev' argument from ide_hwif_setup_dma().
* Un-static ide_hwif_setup_dma() and add CONFIG_BLK_DEV_IDEDMA_PCI=n version.
* Add 'const struct ide_port_info *d' argument to ide_device_add[_all]().
* Factor out generic ports init from ide_pci_setup_ports() to ide_init_port(),
move it to ide-probe.c and call it in in ide_device_add_all() instead of
ide_pci_setup_ports().
* Move ->mate setup to ide_device_add_all() from ide_port_init().
* Add IDE_HFLAG_NO_AUTOTUNE host flag for host drivers that don't enable
->autotune currently.
* Setup hwif->chipset in ide_init_port() but iff pi->chipset is set
(to not override setup done by ide_hwif_configure()).
* Add ETRAX host handling to ide_device_add_all().
* cmd640.c: set IDE_HFLAG_ABUSE_* also for CONFIG_BLK_DEV_CMD640_ENHANCED=n.
* pmac.c: make pmac_ide_setup_dma() return an error value and move DMA masks
setup to pmac_ide_setup_device().
* Add 'struct ide_port_info' instances to legacy host drivers, pass them to
ide_device_add() calls and then remove open-coded ports initialization.
Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Setup ->mate and ->channel in ide_pci_setup_ports() instead of
in ide_hwif_configure().
* Make 'port' parameter for ide_hwif_configure() 'unsigned int'.
* Separate PCI specific init from generic init in ide_pci_setup_ports().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Always set DMA masks in ide_pci_setup_ports() to make sure that the valid
masks for a host are set.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Nowadays IDE core always provides drive ID and ide-disk always setups
drive->capacity64 so this quirk is no longer needed.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Don't override the cable type if the "idex=ata66" parameter was used.
While at it:
* atiixp.c: factor out cable detection to atiixp_cable_detect() from
init_hwif_atiixp().
* cs5535.c: pass 'ide_hwif_t *hwif' instead of 'struct pci_dev *dev' to
cs5535_cable_detect().
* scc_pata.c: factor out cable detection to scc_cable_detect() from
init_hwif_scc() and remove incorrect comment.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The host driver must set hwif's ->no_io_32bit setting not drive's one
(ide_port_tune_devices() overrides drive's setting).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On DTC2278 32-bit I/O has to be enabled for both devices on the port
so always enable it during init time and disallow further changes.
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
sg_dma_len(sg) is invalid before the s/g list is DMA-mapped.
This fixes a post 2.6.24 regression which prevents access to SBP-2
devices on several architectures, introduced by "ieee1394: sbp2: s/g
list access cosmetics", commit 825f1df545.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
- Buttons on the BF533-STAMP board are not inverted
- Fix spurious GPIO Interrupt caused during set irq_type for edge triggered interrupts
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
The definitions of the line discipline numbers N_* have been moved
from asm-*/termios.h to linux/tty.h, but the Blackfin architecture
has somehow evaded that move. Bring it in line with the others.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Move the init sections to the end of memory so that after they
are free, run time memory is all continugous - this should help decrease
memory fragementation.
When doing this, we also pack some of the other sections a little closer
together, to make sure we don't waste memory. To make this happen,
we need to rename the .data.init_task section to .init_task.data, so
it doesn't get picked up by the linker script glob.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
To save/restore the trace buffer control so that if we take an exception
after turning off the trace buffer at a higher level we dont inadvertently
turn the trace buffer back on
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
According to ACPI spec, the _TSD object provides T-state control cross
logical processor dependency information to OSPM. So the t-state
coordination should be considered when T-state for one cpu is changed.
According to ACPI spec, three types of coordination are defined.
SW_ALL, SW_ANY and HW_ALL.
SW_ALL: it means that OSPM needs to initiate T-state transition on
all processors in the domain. It is necessary to call throttling set function
for all affected cpus.
SW_ANY: it means that OSPM may initiate T-state transition on any processor in
the domain.
HW_ALL: Spec only says that hardware will perform the coordination and doesn't
recommend how OSPM coordinate T-state among the affected cpus. So it is treated
as the type of SW_ALL. It means that OSPM needs to initiate t-state transition
on all the processors in the domain.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The t-state coordination should be considered when T-state for one cpu
is changed.It means that OSPM should select one proper target T-state for
the all affected cpus before updating T-state.
So the function of acpi_processor_throttling_notifier is added.
Before updating T-state it can be called for all the affected cpus to get
the proper target T-state, which can meet the requirement of thermal, user and
_TPC. After updating T-state, it can be called to update T-state flag.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Accordint to ACPI spec, the _TSD object provides T-state control cross
logical processor dependency information to OSPM.
After the _TSD data for all cpus are obtained, OSPM will set up
the T-state coordination between CPUs.
Of course if the _TSD doesn't exist or _TSD data is incorrect , it is
assumed that there is no T-state coordination and T-state is changed
independently.
Now there is no proper solution to update T-state coordination after
one cpu is hotplugged. So this patch won't support hotplugged cpu very well.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
It is necessary to check the parameter when calling the function of
acpi_processor_get/set_throttling function so as to avoid the NULL
pointer reference in pr or throttling.
http://bugzilla.kernel.org/show_bug.cgi?id=9747
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The ACPI_PDC_SMP_T_SWCOORD bit is set by and OS that is capable of
native ACPI throttling software coordination for mutli-processors
using the _TSD information.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Vendors often ship machines with a choice of integrated or discrete
graphics, and use the same DSDT for both. As a result, the ACPI video
module will locate devices that may not exist on this specific platform.
Attempt to determine whether the device exists or not, and abort the
device creation if it doesn't.
http://bugzilla.kernel.org/show_bug.cgi?id=9614
Signed-off-by: Matthew Garrett <mjg59@srcf.ucam.org>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This fixes a bug (zero pointer access) only seen on BF561, during USB
Mass Storage/SCSI Host initialization.
It appears to be related to registering a none existing CPU
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
- Add support for irq_wake on system and gpio interrupts
- Remove outdated kernel options
- Add option to select default PM mode
- Fix various places where SIC_IWRx was only handled partially
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Merge single core ints-priority-sc.c and dual core ints-priority-dc.c
into one common code ints-priority.c
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
