Since ocfs2_cow_file_pos will invoke ocfs2_refcount_icow with a NULL as
the struct file pointer, it finally result in a null pointer dereference
in ocfs2_duplicate_clusters_by_page.
This patch replace file pointer with inode pointer in
cow_duplicate_clusters to fix this issue.
[jeff.liu@oracle.com: rebased patch against linux-next tree]
Signed-off-by: Tiger Yang <tiger.yang@oracle.com>
Signed-off-by: Jie Liu <jeff.liu@oracle.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Mark Fasheh <mfasheh@suse.com>
Acked-by: Tao Ma <tm@tao.ma>
Tested-by: David Weber <wb@munzinger.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert commit 40bd62eb7f ("fs/ocfs2/journal.h: add bits_wanted while
calculating credits in ocfs2_calc_extend_credits").
Unfortunately this change broke fallocate even if there is insufficient
disk space for the preallocation, which is a serious problem.
# df -h
/dev/sda8 22G 1.2G 21G 6% /ocfs2
# fallocate -o 0 -l 200M /ocfs2/testfile
fallocate: /ocfs2/test: fallocate failed: No space left on device
and a kernel warning:
CPU: 3 PID: 3656 Comm: fallocate Tainted: G W O 3.11.0-rc3 #2
Call Trace:
dump_stack+0x77/0x9e
warn_slowpath_common+0xc4/0x110
warn_slowpath_null+0x2a/0x40
start_this_handle+0x6c/0x640 [jbd2]
jbd2__journal_start+0x138/0x300 [jbd2]
jbd2_journal_start+0x23/0x30 [jbd2]
ocfs2_start_trans+0x166/0x300 [ocfs2]
__ocfs2_extend_allocation+0x38f/0xdb0 [ocfs2]
ocfs2_allocate_unwritten_extents+0x3c9/0x520
__ocfs2_change_file_space+0x5e0/0xa60 [ocfs2]
ocfs2_fallocate+0xb1/0xe0 [ocfs2]
do_fallocate+0x1cb/0x220
SyS_fallocate+0x6f/0xb0
system_call_fastpath+0x16/0x1b
JBD2: fallocate wants too many credits (51216 > 4381)
Signed-off-by: Jie Liu <jeff.liu@oracle.com>
Cc: Goldwyn Rodrigues <rgoldwyn@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Mark Fasheh <mfasheh@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It's always a bad idea to poll on HW bits without a timeout.
The i.MX28 RTC can be easily brought into a state in which the RTC is
not running (until after a power-on-reset) and thus the status bits
which are polled in the driver won't ever change.
This patch prevents the kernel from getting stuck in this case.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dave has reported the following lockdep splat:
=================================
[ INFO: inconsistent lock state ]
3.11.0-rc1+ #9 Not tainted
---------------------------------
inconsistent {RECLAIM_FS-ON-W} -> {IN-RECLAIM_FS-W} usage.
kswapd0/49 [HC0[0]:SC0[0]:HE1:SE1] takes:
(&mapping->i_mmap_mutex){+.+.?.}, at: [<c114971b>] page_referenced+0x87/0x5e3
{RECLAIM_FS-ON-W} state was registered at:
mark_held_locks+0x81/0xe7
lockdep_trace_alloc+0x5e/0xbc
__alloc_pages_nodemask+0x8b/0x9b6
__get_free_pages+0x20/0x31
get_zeroed_page+0x12/0x14
__pmd_alloc+0x1c/0x6b
huge_pmd_share+0x265/0x283
huge_pte_alloc+0x5d/0x71
hugetlb_fault+0x7c/0x64a
handle_mm_fault+0x255/0x299
__do_page_fault+0x142/0x55c
do_page_fault+0xd/0x16
error_code+0x6c/0x74
irq event stamp: 3136917
hardirqs last enabled at (3136917): _raw_spin_unlock_irq+0x27/0x50
hardirqs last disabled at (3136916): _raw_spin_lock_irq+0x15/0x78
softirqs last enabled at (3136180): __do_softirq+0x137/0x30f
softirqs last disabled at (3136175): irq_exit+0xa8/0xaa
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&mapping->i_mmap_mutex);
<Interrupt>
lock(&mapping->i_mmap_mutex);
*** DEADLOCK ***
no locks held by kswapd0/49.
stack backtrace:
CPU: 1 PID: 49 Comm: kswapd0 Not tainted 3.11.0-rc1+ #9
Hardware name: Dell Inc. Precision WorkStation 490 /0DT031, BIOS A08 04/25/2008
Call Trace:
dump_stack+0x4b/0x79
print_usage_bug+0x1d9/0x1e3
mark_lock+0x1e0/0x261
__lock_acquire+0x623/0x17f2
lock_acquire+0x7d/0x195
mutex_lock_nested+0x6c/0x3a7
page_referenced+0x87/0x5e3
shrink_page_list+0x3d9/0x947
shrink_inactive_list+0x155/0x4cb
shrink_lruvec+0x300/0x5ce
shrink_zone+0x53/0x14e
kswapd+0x517/0xa75
kthread+0xa8/0xaa
ret_from_kernel_thread+0x1b/0x28
which is a false positive caused by hugetlb pmd sharing code which
allocates a new pmd from withing mapping->i_mmap_mutex. If this
allocation causes reclaim then the lockdep detector complains that we
might self-deadlock.
This is not correct though, because hugetlb pages are not reclaimable so
their mapping will be never touched from the reclaim path.
The patch tells lockup detector that hugetlb i_mmap_mutex is special by
assigning it a separate lockdep class so it won't report possible
deadlocks on unrelated mappings.
[peterz@infradead.org: comment for annotation]
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Cc: Peter Zijlstra <peterz@infradead.org>
Reviewed-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a BUG which can trigger when direct-IO is used with AOE.
As discussed previously, the fact that some users of the block layer
provide bios that point to pages with a zero _count means that it is not
OK for the network layer to do a put_page on the skb frags during an
skb_linearize, so the aoe driver gets a reference to pages in bios and
puts the reference before ending the bio. And because it cannot use
get_page on a page with a zero _count, it manipulates the value
directly.
It is not OK to increment the _count of a compound page tail, though,
since the VM layer will VM_BUG_ON a non-zero _count. Block users that
do direct I/O can result in the aoe driver seeing compound page tails in
bios. In that case, the same logic works as long as the head of the
compound page is used instead of the tails. This patch handles compound
pages and does not BUG.
It relies on the block layer user leaving the relationship between the
page tail and its head alone for the duration between the submission of
the bio and its completion, whether successful or not.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix inadvertent breakage in the clone syscall ABI for Microblaze that
was introduced in commit f3268edbe6 ("microblaze: switch to generic
fork/vfork/clone").
The Microblaze syscall ABI for clone takes the parent tid address in the
4th argument; the third argument slot is used for the stack size. The
incorrectly-used CLONE_BACKWARDS type assigned parent tid to the 3rd
slot.
This commit restores the original ABI so that existing userspace libc
code will work correctly.
All kernel versions from v3.8-rc1 were affected.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andy reported that if file page get reclaimed we lose the soft-dirty bit
if it was there, so save _PAGE_BIT_SOFT_DIRTY bit when page address get
encoded into pte entry. Thus when #pf happens on such non-present pte
we can restore it back.
Reported-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@gmail.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andy Lutomirski reported that if a page with _PAGE_SOFT_DIRTY bit set
get swapped out, the bit is getting lost and no longer available when
pte read back.
To resolve this we introduce _PTE_SWP_SOFT_DIRTY bit which is saved in
pte entry for the page being swapped out. When such page is to be read
back from a swap cache we check for bit presence and if it's there we
clear it and restore the former _PAGE_SOFT_DIRTY bit back.
One of the problem was to find a place in pte entry where we can save
the _PTE_SWP_SOFT_DIRTY bit while page is in swap. The _PAGE_PSE was
chosen for that, it doesn't intersect with swap entry format stored in
pte.
Reported-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@gmail.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com>
Reviewed-by: Minchan Kim <minchan@kernel.org>
Reviewed-by: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
struct memcg_cache_params has a union. Different parts of this union
are used for root and non-root caches. A part with destroying work is
used only for non-root caches.
I fixed the same problem in another place v3.9-rc1-16204-gf101a94, but
didn't notice this one.
This patch fixes the kernel panic:
[ 46.848187] BUG: unable to handle kernel paging request at 000000fffffffeb8
[ 46.849026] IP: [<ffffffff811a484c>] kmem_cache_destroy_memcg_children+0x6c/0xc0
[ 46.849092] PGD 0
[ 46.849092] Oops: 0000 [#1] SMP
...
Signed-off-by: Andrey Vagin <avagin@openvz.org>
Cc: Glauber Costa <glommer@openvz.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: <stable@vger.kernel.org> [3.9.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit cab70040df ("net: igmp:
Reduce Unsolicited report interval to 1s when using IGMPv3") and
2690048c01 ("net: igmp: Allow user-space
configuration of igmp unsolicited report interval") by William Manley made
igmp unsolicited report intervals configurable per interface and corrected
the interval of unsolicited igmpv3 report messages resendings to 1s.
Same needs to be done for IPv6:
MLDv1 (RFC2710 7.10.): 10 seconds
MLDv2 (RFC3810 9.11.): 1 second
Both intervals are configurable via new procfs knobs
mldv1_unsolicited_report_interval and mldv2_unsolicited_report_interval.
(also added .force_mld_version to ipv6_devconf_dflt to bring structs in
line without semantic changes)
v2:
a) Joined documentation update for IPv4 and IPv6 MLD/IGMP
unsolicited_report_interval procfs knobs.
b) incorporate stylistic feedback from William Manley
v3:
a) add new DEVCONF_* values to the end of the enum (thanks to David
Miller)
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: William Manley <william.manley@youview.com>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initially I improperly set a boundary for maximum number of input
packets to process on NAPI poll ("work") so it might be more than
expected amount ("weight").
This was really harmless but seeing WARN_ON_ONCE on every device boot is
not nice. So trivial fix ("<" instead of "<=") is here.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull scheduler fixes from Ingo Molnar:
"Docbook fixes that make 99% of the diffstat, plus a oneliner fix"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched: Ensure update_cfs_shares() is called for parents of continuously-running tasks
sched: Fix some kernel-doc warnings
Pull perf fixes from Ingo Molnar:
"Two small fixlets"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86: Add Haswell ULT model number used in Macbook Air and other systems
perf/x86: Fix intel QPI uncore event definitions
Using inner-id for tunnel id is not safe in some rare cases.
E.g. packets coming from multiple sources entering same tunnel
can have same id. Therefore on tunnel packet receive we
could have packets from two different stream but with same
source and dst IP with same ip-id which could confuse ip packet
reassembly.
Following patch reverts optimization from commit
490ab08127 (IP_GRE: Fix IP-Identification.)
CC: Jarno Rajahalme <jrajahalme@nicira.com>
CC: Ansis Atteka <aatteka@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The secure element state was not updated from the enable/disable ops,
leaving the SE state to disabled for ever.
Signed-off-by: Arron Wang <arron.wang@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Another typo from the initial commit where we check for the secure
element type field instead of its state when enabling or disabling it.
Signed-off-by: Arron Wang <arron.wang@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
There is a cut and paste bug so we enable a second time instead of
disabling.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The pn544 can enter a firmware update mode where firmware blobs can be
pushed through the i2c line and flashed on the target.
A special command allows to verify that blobs are correctly flashed and
this is what we do for every downloaded firmware blob.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The firmware operation callback is passed by the physical layer to the
hci driver during probe. All the driver does is to store it and call it
when the fw_upload hci ops is invoked.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Result is added as an NFC_ATTR_FIRMWARE_DOWNLOAD_STATUS attribute
containing the standard errno positive value of the completion result.
This event will be sent when the firmare download operation is done and
will contain the operation result.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
On timeout the TCP sender unconditionally resets the estimated degree
of network reordering (tp->reordering). The idea behind this is that
the estimate is too large to trigger fast recovery (e.g., due to a IP
path change).
But for example if the sender only had 2 packets outstanding, then a
timeout doesn't tell much about reordering. A sender that learns about
reordering on big writes and loses packets on small writes will end up
falsely retransmitting again and again, especially when reordering is
more likely on big writes.
Therefore the sender should only suspect that tp->reordering is too
high if it could have gone into fast recovery with the (lower) default
estimate.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is in preparation for pn544-i2c firmware download feature, where we
need to know if we're in regular or firmware upload mode.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This API must be called by NFC drivers, and its prototype was
incorrectly placed.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Dmitry Kravkov says:
====================
Please consider applying the series of bnx2x fixes to net:
* statistics may cause FW assert
* missing fairness configuration in DCB flow
* memory leak in sriov related part
* Illegal PTE access
* Pagefault crash in shutdown flow with cnic
v1->v2
* fixed sparse error pointed by Joe Perches
* added missing signed-off from Sergei Shtylyov
v2->v3
* added missing signed-off from Sergei Shtylyov
* fixed formatting from Sergei Shtylyov
v3->v4
* patch 1/6: fixed declaration order
* patch 2/6 replaced with: protect flows using set_bit constraints
v4->v5
* patch 2/6: replace proprietary locking with semaphore
* droped 1/6: since adds redundant code from Benjamin Poirier
The following patchset contains four netfilter fixes, they are:
* Fix possible invalid access and mangling of the TCPMSS option in
xt_TCPMSS. This was spotted by Julian Anastasov.
* Fix possible off by one access and mangling of the TCP packet in
xt_TCPOPTSTRIP, also spotted by Julian Anastasov.
* Fix possible information leak due to missing initialization of one
padding field of several structures that are included in nfqueue and
nflog netlink messages, from Dan Carpenter.
* Fix TCP window tracking with Fast Open, from Yuchung Cheng.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There might be a crash as during shutdown flow CNIC might try
to access resources already freed by bnx2x.
Change bnx2x_close() into dev_close() in __bnx2x_remove (shutdown flow)
to guarantee CNIC is notified of the device's change of status.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PTE write access error might occur in MF_ALLOWED mode when IOMMU
is active. The patch adds rmmod HSI indicating to MFW to stop
running queries which might trigger this failure.
Signed-off-by: Barak Witkowsky <barak@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ETS can be enabled as a result of DCB negotiation, then
fairness must be recalculated after each negotiation.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add locking to protect different statistics flows from
running simultaneously.
This in order to serialize statistics requests sent to FW,
otherwise two outstanding queries may cause FW assert.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
This is a batch of updates intended for 3.12. It is mostly driver
stuff, although Johannes Berg and Simon Wunderlich make a good
showing with mac80211 bits (particularly some work on 5/10 MHz
channel support).
The usual suspects are mostly represented. There are lots of updates
to iwlwifi, ath9k, ath10k, mwifiex, rt2x00, wil6210, as usual.
The bcma bus gets some love this time, as do cw1200, iwl4965, and a
few other bits here and there. I don't think there is much unusual
here, FWIW.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The new IP version which is present in AM43xx SoC has a minor changes and the
offsets are same as the previous version, so adding new IP version support in
the driver.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pm_qos_update_request_timeout() updates a qos and then schedules
a delayed work item to bring the qos back down to the default
after the timeout. When the work item runs, pm_qos_work_fn() will
call pm_qos_update_request() and deadlock because it tries to
cancel itself via cancel_delayed_work_sync(). Future callers of
that qos will also hang waiting to cancel the work that is
canceling itself. Let's extract the little bit of code that does
the real work of pm_qos_update_request() and call it from the
work function so that we don't deadlock.
Before ed1ac6e (PM: don't use [delayed_]work_pending()) this didn't
happen because the work function wouldn't try to cancel itself.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Tejun Heo <tj@kernel.org>
Cc: 3.9+ <stable@vger.kernel.org> # 3.9+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
By not always starting the polling loop from the same modulation, we
avoid entering infinite loops where devices exporting 2 targets (on 2
different modulations) get the same target activated over and over.
If this target is not readable (e.g. a wallet emulating a tag), we will
stay in an error loop for ever.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
It seems that some pn533 firmwares go belly up when being asked to send
poll frames too frequently. Adding a 10ms delay between each of them
calm the chip down and prevent it from crashing.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In order to fetch the discovered secure elements from an NFC controller,
we need to send a netlink command that will dump the list of available
SEs from NFC.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This is a typo coming from the initial implementation. se_discover fails
when it returns something different than zero and we should only display
a warning in that case.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The extended information frame are sent by PN533 to exchange frames
larger than 255 bytes. These extended frame are very close from the
standard ones except for the header size length. On each incoming
frame, we set the correct header length, and we do that only for the
standard pn533 chipsets as the acr122 does not seem to support extended
frames properly.
Signed-off-by: Olivier Guiter <olivier.guiter@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
On sending large frames (size > 262), we split it in multiple chunks and
send them asynchronously with MI bit.
Signed-off-by: Olivier Guiter <olivier.guiter@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Extended Information frames are slightly different from standard frames
as they can (theorically) handle datas up tu 64kB. PN533 firmware only
supports packet data up to 265 (incl. TFI byte)
This kind of frame are used when the pn533 wants to exchange more than
255 bytes, and this patch handles the reception of such frames.
Signed-off-by: Olivier Guiter <olivier.guiter@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The AUTO RFCA bit forbids the pn533 chipset to turn its radio on
whenever an external field is present.
Without this bit set, some devices seems to get over flood by the
pn533 rf field and thus become hardly detectable.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
p2p devices must be able to support 424 kbps, so we should always select
that bitrate in initiator mode.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
By turning the radio off after each failed polling try, we dramatically
improve the pn533 polling loop efficiency.
Without this fix, all Android phones running the broadcom NFC stack are
almost never detected.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
By using the standard setting for the regular pn533 dongles, we no
longer wait for ever for an ATR_RES. Without this, a failing ATR_REQ
will put the hardware into a busy loop, constantly waiting for an
ATR_RES.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The SE_CONNECTIVITY event is for an SE to request connection to e.g. a
modem. The SE_TRANSACTION one is sent when an application running on a
specific SE wants to notify the host CPU about the end of a transaction.
Those events respectively map to the EVT_CONNECTIVITY and the
EVT_TRANSACTION HCI events.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
eTSEC has Rx and Tx flow control capabilities that may be enabled
through MACCFG1[Rx_Flow, Tx_Flow] bits. These bits must not be set
however when eTSEC is operated in Half-Duplex mode. Unfortunately,
the driver currently sets these bits unconditionally.
This patch adds the proper handling of the PAUSE frame capability
register bits by implementing the ethtool -A interface. When pause
autoneg is enabled, the controller uses the phy's capability to
negotiate PAUSE frame settings with the link partner and reconfigures
its Rx_Flow and Tx_Flow settings to match the capabilities of the
link partner. If pause autoneg is off, the PAUSE frame generation
may be forced manually (ethtool -A). Flow control is disabled by
default now.
This implementation is inspired by the tg3 driver.
Signed-off-by: Lutz Jaenicke <ljaenicke@innominate.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes 3 sparse warnings:
nfcsim.c:63:25: sparse: symbol 'wq' was not declared.
nfcsim.c:484:12: sparse: symbol 'nfcsim_init' was not declared.
nfcsim.c:525:13: sparse: symbol 'nfcsim_exit' was not declared.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
