When copying between device and command protection scatters
we must take into account that device scatters might be offset
and we might copy outside scatter range. Thus for each cmd prot
scatter we must take the min between cmd prot scatter, dev prot
scatter, and whats left (and loop in case we havn't copied enough
from/to cmd prot scatter).
Example (single t_prot_sg of len 2048):
kernel: sbc_dif_copy_prot: se_cmd=ffff880380aaf970, left=2048, len=2048, dev_prot_sg_offset=3072, dev_prot_sg_len=4096
kernel: isert: se_cmd=ffff880380aaf970 PI error found type 0 at sector 0x2600 expected 0x0 vs actual 0x725f, lba=2580
Instead of copying 2048 from offset 3072 (copying junk outside sg
limit 4096), we must to copy 1024 and continue to next sg until
we complete cmd prot scatter.
This issue was found using iSER T10-PI offload over rd_mcp (wasn't
discovered with fileio since file_dev prot sglists are never offset).
Changes from v1:
- Fix sbc_copy_prot copy length miss-calculation
Changes from v0:
- Removed psg->offset consideration for psg_len computation
- Removed sg->offset consideration for offset condition
- Added copied consideraiton for len computation
- Added copied offset to paddr when doing memcpy
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now that AIC23 supports two control interfaces all existing I2C users
should select I2C variant.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
tlv320aic23 chip control interface may work in either I2C or SPI mode
depending on the MODE pin state. Functionality and register layout are
independent of the control mode.
Implement bus-specific parts as separate modules.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The 64bit relocation code places a few symbols in the text segment.
These symbols are only 4 byte aligned where they need to be 8 byte
aligned. Add an explicit alignment.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: stable@vger.kernel.org
Tested-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When we fork/clone we currently don't copy any of the TM state to the new
thread. This results in a TM bad thing (program check) when the new process is
switched in as the kernel does a tmrechkpt with TEXASR FS not set. Also, since
R1 is from userspace, we trigger the bad kernel stack pointer detection. So we
end up with something like this:
Bad kernel stack pointer 0 at c0000000000404fc
cpu 0x2: Vector: 700 (Program Check) at [c00000003ffefd40]
pc: c0000000000404fc: restore_gprs+0xc0/0x148
lr: 0000000000000000
sp: 0
msr: 9000000100201030
current = 0xc000001dd1417c30
paca = 0xc00000000fe00800 softe: 0 irq_happened: 0x01
pid = 0, comm = swapper/2
WARNING: exception is not recoverable, can't continue
The below fixes this by flushing the TM state before we copy the task_struct to
the clone. To do this we go through the tmreclaim patch, which removes the
checkpointed registers from the CPU and transitions the CPU out of TM suspend
mode. Hence we need to call tmrechkpt after to restore the checkpointed state
and the TM mode for the current task.
To make this fail from userspace is simply:
tbegin
li r0, 2
sc
<boom>
Kudos to Adhemerval Zanella Neto for finding this.
Signed-off-by: Michael Neuling <mikey@neuling.org>
cc: Adhemerval Zanella Neto <azanella@br.ibm.com>
cc: stable@vger.kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
one more radeon fix.
* 'drm-fixes-3.14' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon/atom: select the proper number of lanes in transmitter setup
Add a maintainers entry for the TDA998x driver. Rob Clark has handed
this driver over to me to look after.
Acked-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
a few more radeon fixes.
* 'drm-fixes-3.14' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon/dpm: fix typo in EVERGREEN_SMC_FIRMWARE_HEADER_softRegisters
drm/radeon/cik: fix typo in documentation
drm/radeon: silence GCC warning on 32 bit
drm/radeon: resume old pm late
drm/radeon: TTM must be init with cpu-visible VRAM, v2
Building radeon_ttm.o on 32 bit x86 triggers a warning:
In file included from include/asm-generic/bug.h:13:0,
from [...]/arch/x86/include/asm/bug.h:38,
from include/linux/bug.h:4,
from include/drm/drm_mm.h:39,
from include/drm/drm_vma_manager.h:26,
from include/drm/ttm/ttm_bo_api.h:35,
from drivers/gpu/drm/radeon/radeon_ttm.c:32:
drivers/gpu/drm/radeon/radeon_ttm.c: In function 'radeon_ttm_gtt_read':
include/linux/kernel.h:712:17: warning: comparison of distinct pointer types lacks a cast [enabled by default]
(void) (&_min1 == &_min2); \
^
drivers/gpu/drm/radeon/radeon_ttm.c:938:22: note: in expansion of macro 'min'
ssize_t cur_size = min(size, PAGE_SIZE - off);
^
Silence this warning by using min_t(). Since cur_size will never be
negative and its upper bound is PAGE_SIZE, we can change its type to
size_t and use min_t(size_t, [...]) here.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Moving the pm resume up in the init order to fix
dpm seems to have regressed somes cases with the old
pm code. Move it back to late resume.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Without this, a bo may get created in the cpu-inaccessible vram.
Before the CP engines get setup, all copies are done via cpu memcpy.
This means that the cpu tries to read from inaccessible memory, fails,
and the radeon module proceeds to disable acceleration.
Doing this has no downsides, as the real VRAM size gets set as soon as the
CP engines get init.
This is a candidate for 3.14 fixes.
v2: Add comment on why the function is used
Signed-off-by: Lauri Kasanen <cand@gmx.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Since commit bd972688eb
"firewire: ohci: Fix 'failed to read phy reg' on FW643 rev8",
there is a high chance that firewire-ohci fails to initialize LSI née
Agere controllers.
https://bugzilla.kernel.org/show_bug.cgi?id=65151
Peter Hurley points out the reason: IEEE 1394a:2000 clause 5A.1 (or
IEEE 1394:2008 clause 17.2.1) say: "The PHY shall insure that no more
than 10 ms elapse from the reassertion of LPS until the interface is
reset. The link shall not assert LReq until the reset is complete."
In other words, the link needs to give the PHY at least 10 ms to get
the interface operational.
With just the msleep(1) in bd972688eb, the first read_phy_reg()
during ohci_enable() may happen before the phy-link interface reset was
finished, and fail. Due to the high variability of msleep(n) with small
n, this failure was not fully reproducible, and not apparent at all with
low CONFIG_HZ setting.
On the other hand, Peter can no longer reproduce the issue with FW643
rev8. The read phy reg failures that happened back then may have had an
unrelated cause. So, just revert bd972688eb, except for the valid
comment on TSB82AA2 cards.
Reported-by: Mikhail Gavrilov
Reported-by: Jay Fenlason <fenlason@redhat.com>
Reported-by: Clemens Ladisch <clemens@ladisch.de>
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Cc: stable@vger.kernel.org # v3.10+
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The Documentation for the thin provisioning target's held metadata root
feature was incorrect. It is now available and the value for the held
metadata root is in block units (not 512b sectors).
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Building on commit 0ac09f9f8c ("x86, trace: Fix CR2 corruption when
tracing page faults") this patch addresses another few issues:
- Now that read_cr2() is lifted into trace_do_page_fault(), we should
pass the address to trace_page_fault_entries() to avoid it
re-reading a potentially changed cr2.
- Put both trace_do_page_fault() and trace_page_fault_entries() under
CONFIG_TRACING.
- Mark both fault entry functions {,trace_}do_page_fault() as notrace
to avoid getting __mcount or other function entry trace callbacks
before we've observed CR2.
- Mark __do_page_fault() as noinline to guarantee the function tracer
does get to see the fault.
Cc: <jolsa@redhat.com>
Cc: <vincent.weaver@maine.edu>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20140306145300.GO9987@twins.programming.kicks-ass.net
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
A number of Samsung notebooks (530Uxx/535Uxx/540Uxx/550Pxx/900Xxx/etc)
continue to log events during sleep (lid open/close, AC plug/unplug,
battery level change), which accumulate in the EC until a buffer fills.
After the buffer is full (tests suggest it holds 8 events), GPEs stop
being triggered for new events. This state persists on wake or even on
power cycle, and prevents new events from being registered until the EC
is manually polled.
This is the root cause of a number of bugs, including AC not being
detected properly, lid close not triggering suspend, and low ambient
light not triggering the keyboard backlight. The bug also seemed to be
responsible for performance issues on at least one user's machine.
Juan Manuel Cabo found the cause of bug and the workaround of polling
the EC manually on wake.
The loop which clears the stale events is based on an earlier patch by
Lan Tianyu (see referenced attachment).
This patch:
- Adds a function acpi_ec_clear() which polls the EC for stale _Q
events at most ACPI_EC_CLEAR_MAX (currently 100) times. A warning is
logged if this limit is reached.
- Adds a flag EC_FLAGS_CLEAR_ON_RESUME which is set to 1 if the DMI
system vendor is Samsung. This check could be replaced by several
more specific DMI vendor/product pairs, but it's likely that the bug
affects more Samsung products than just the five series mentioned
above. Further, it should not be harmful to run acpi_ec_clear() on
systems without the bug; it will return immediately after finding no
data waiting.
- Runs acpi_ec_clear() on initialisation (boot), from acpi_ec_add()
- Runs acpi_ec_clear() on wake, from acpi_ec_unblock_transactions()
References: https://bugzilla.kernel.org/show_bug.cgi?id=44161
References: https://bugzilla.kernel.org/show_bug.cgi?id=45461
References: https://bugzilla.kernel.org/show_bug.cgi?id=57271
References: https://bugzilla.kernel.org/attachment.cgi?id=126801
Suggested-by: Juan Manuel Cabo <juanmanuel.cabo@gmail.com>
Signed-off-by: Kieran Clancy <clancy.kieran@gmail.com>
Reviewed-by: Lan Tianyu <tianyu.lan@intel.com>
Reviewed-by: Dennis Jansen <dennis.jansen@web.de>
Tested-by: Kieran Clancy <clancy.kieran@gmail.com>
Tested-by: Juan Manuel Cabo <juanmanuel.cabo@gmail.com>
Tested-by: Dennis Jansen <dennis.jansen@web.de>
Tested-by: Maurizio D'Addona <mauritiusdadd@gmail.com>
Tested-by: San Zamoyski <san@plusnet.pl>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
policy->rwsem is used to lock access to all parts of code modifying
struct cpufreq_policy, but it's not used on a new policy created by
__cpufreq_add_dev().
Because of that, if cpufreq_update_policy() is called in a tight loop
on one CPU in parallel with offline/online of another CPU, then the
following crash can be triggered:
Unable to handle kernel NULL pointer dereference at virtual address 00000020
pgd = c0003000
[00000020] *pgd=80000000004003, *pmd=00000000
Internal error: Oops: 206 [#1] PREEMPT SMP ARM
PC is at __cpufreq_governor+0x10/0x1ac
LR is at cpufreq_update_policy+0x114/0x150
---[ end trace f23a8defea6cd706 ]---
Kernel panic - not syncing: Fatal exception
CPU0: stopping
CPU: 0 PID: 7136 Comm: mpdecision Tainted: G D W 3.10.0-gd727407-00074-g979ede8 #396
[<c0afe180>] (notifier_call_chain+0x40/0x68) from [<c02a23ac>] (__blocking_notifier_call_chain+0x40/0x58)
[<c02a23ac>] (__blocking_notifier_call_chain+0x40/0x58) from [<c02a23d8>] (blocking_notifier_call_chain+0x14/0x1c)
[<c02a23d8>] (blocking_notifier_call_chain+0x14/0x1c) from [<c0803c68>] (cpufreq_set_policy+0xd4/0x2b8)
[<c0803c68>] (cpufreq_set_policy+0xd4/0x2b8) from [<c0803e7c>] (cpufreq_init_policy+0x30/0x98)
[<c0803e7c>] (cpufreq_init_policy+0x30/0x98) from [<c0805a18>] (__cpufreq_add_dev.isra.17+0x4dc/0x7a4)
[<c0805a18>] (__cpufreq_add_dev.isra.17+0x4dc/0x7a4) from [<c0805d38>] (cpufreq_cpu_callback+0x58/0x84)
[<c0805d38>] (cpufreq_cpu_callback+0x58/0x84) from [<c0afe180>] (notifier_call_chain+0x40/0x68)
[<c0afe180>] (notifier_call_chain+0x40/0x68) from [<c02812dc>] (__cpu_notify+0x28/0x44)
[<c02812dc>] (__cpu_notify+0x28/0x44) from [<c0aeed90>] (_cpu_up+0xf4/0x1dc)
[<c0aeed90>] (_cpu_up+0xf4/0x1dc) from [<c0aeeed4>] (cpu_up+0x5c/0x78)
[<c0aeeed4>] (cpu_up+0x5c/0x78) from [<c0aec808>] (store_online+0x44/0x74)
[<c0aec808>] (store_online+0x44/0x74) from [<c03a40f4>] (sysfs_write_file+0x108/0x14c)
[<c03a40f4>] (sysfs_write_file+0x108/0x14c) from [<c03517d4>] (vfs_write+0xd0/0x180)
[<c03517d4>] (vfs_write+0xd0/0x180) from [<c0351ca8>] (SyS_write+0x38/0x68)
[<c0351ca8>] (SyS_write+0x38/0x68) from [<c0205de0>] (ret_fast_syscall+0x0/0x30)
Fix that by taking locks at appropriate places in __cpufreq_add_dev()
as well.
Reported-by: Saravana Kannan <skannan@codeaurora.org>
Suggested-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
[rjw: Changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Policy must be fully initialized before it is being made available
for use by others. Otherwise cpufreq_cpu_get() would be able to grab
a half initialized policy structure that might not have affected_cpus
(for example) populated. Then, anybody accessing those fields will get
a wrong value and that will lead to unpredictable results.
In order to fix this, do all the necessary initialization before we
make the policy structure available via cpufreq_cpu_get(). That will
guarantee that any code accessing fields of the policy will get
correct data from them.
Reported-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
[rjw: Changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If a module calls cpufreq_get while cpufreq is initializing, it's
possible for it to be called after cpufreq_driver is set but before
cpufreq_cpu_data is written during subsys_interface_register. This
happens because cpufreq_get doesn't take the cpufreq_driver_lock
around its use of cpufreq_cpu_data.
Fix this by using cpufreq_cpu_get(cpu) to look up the policy rather
than reading it out of cpufreq_cpu_data directly. cpufreq_cpu_get()
takes the appropriate locks to prevent this race from happening.
Since it's possible for policy to be NULL if the caller passes in an
invalid CPU number or calls the function before cpufreq is initialized,
delete the BUG_ON(!policy) and simply return 0. Don't try to return
-ENOENT because that's negative and the function returns an unsigned
integer.
References: https://bbs.archlinux.org/viewtopic.php?id=177934
Signed-off-by: Aaron Plattner <aplattner@nvidia.com>
Cc: 3.13+ <stable@vger.kernel.org> # 3.13+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In snd_soc_bytes_put function, it forces cpu to do cpu_to_be translation,
but for mmio bus which uses REGMAP_ENDIAN_NATIVE, it doesn't need to do
endian translation. So it is better to use regmap's api which can decide
if this translation is needed according to bus configuration.
Signed-off-by: Nenghua Cao <nhcao@marvell.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This is useful for generic code built on top of regmap dealing with
blocks of data.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=uRux
-----END PGP SIGNATURE-----
Merge tag 'parse-val' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap into asoc-core
regmap: Add parse_val() API
This is useful for generic code built on top of regmap dealing with
blocks of data.
In some cases, we need regmap's format parse_val function
to do be/le translation according to the bus configuration.
For example, snd_soc_bytes_put() uses regmap to write/read values,
and use cpu_to_be() directly to covert MASK into big endian. This
is a defect, and should use regmap's format function to do it according
to bus configuration.
Signed-off-by: Nenghua Cao <nhcao@marvell.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This connects platform DAI, SiRF internal audio codec DAI and
SiRF auido port DAI together and works as a mach driver.
Signed-off-by: Rongjun Ying <rongjun.ying@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This driver is used by SIRF internal audio codec.
Use dedicated SiRF audio port TXFIFO and RXFIFO
Supports two DMA channels for SiRF audio port TXFIFO and RXFIFO
The audio port like as audio bus such as i2s.
Signed-off-by: Rongjun Ying <rongjun.ying@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In preparation for componentization move the ignore_pmdown_time field from the
snd_soc_codec struct to the snd_soc_component struct. Set it to true for non
CODEC components for now.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is no reason why active count tracking should only be done for CODECs but
not for other components. Moving the active count from the snd_soc_codec struct
to the snd_soc_component struct reduces the differences between CODECs and other
components and will eventually allow component to component DAI links (Which is
a prerequisite for converting CODECs to components).
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Keep track of which component registered a DAI. We'll need this as
componentization progresses.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Instead of directly checking the 'active' field of the CODEC struct add a new
helper function that will return either true or false depending on whether the
CODEC is active. This will make the migration to the component level easier.
The patch also updates all CODEC drivers that check the active attribute to use
the new helper function.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
For CODEC to CODEC links we need to make sure to also manage the 'active' field
of the cpu_dai CODEC.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
We have the same code that increments and decrements the active field of the
various PCM runtime components (all with the same bugs). Factor this out into
common helper functions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
For CODEC to CODEC links we should only immediately power down if both CODECs
are configured to ignore the power down delay. Factor the logic for this
into a helper function that can be used for both compressed and normal PCMs.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
SiRF internal audio codec is integrated in SiRF atlas6 and prima2 SoC.
Features include:
1. Stereo DAC and ADC with 16-bit resolution amd 48KHz sample rate
2. Support headphone and/or speaker output
3. Integrate headphone and speaker output amp
4. Support LINE and MIC input
5. Support single ended and differential input mode
Signed-off-by: Rongjun Ying <rongjun.ying@csr.com>
--v5:
1. Drop all inlines.
2. Reordering the Kconfig and Makefile
3. Remove the sirf_audio_codec_reg_bits struct, use the new controls instead it.
4. Add some SND_SOC_DAPM_OUT_DRV instead of HP and SPK enable driver
5. Add audio codec clock supply instead of adc event callback
6. Fixed playback and capture can't concurrent work bug.
--
.../devicetree/bindings/sound/sirf-audio-codec.txt | 17 +
sound/soc/codecs/Kconfig | 5 +
sound/soc/codecs/Makefile | 1 +
sound/soc/codecs/sirf-audio-codec.c | 533 ++++++++++++++++++++
sound/soc/codecs/sirf-audio-codec.h | 75 +++
5 files changed, 631 insertions(+), 0 deletions(-)
create mode 100644 Documentation/devicetree/bindings/sound/sirf-audio-codec.txt
create mode 100644 sound/soc/codecs/sirf-audio-codec.c
create mode 100644 sound/soc/codecs/sirf-audio-codec.h
Signed-off-by: Mark Brown <broonie@linaro.org>
The Z clock frequency change is effective only after setting the kick
bit located in the FRQCRB register.
Without that, the CA15 CPUs clock rate will never change.
Fix that by checking if the kick bit is cleared and enable it to make
the clock rate change effective. The bit is cleared automatically upon
completion.
Signed-off-by: Benoit Cousson <bcousson+renesas@baylibre.com>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The firmware files can be quite large and allocating the whole firmware
a single DMA safe buffer can be problematic if the system is under a
high memory load. Ease the requirements slightly by writing the firmware
out in page sized chunks.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
cs4271_common_probe() is called from cs4271_i2c_probe() but defined in
CONFIG_SPI_MASTER block, thus it results in a build error when
CONFIG_SPI_MASTER=n:
sound/soc/codecs/cs4271.c:721:2: error: implicit declaration of function ‘cs4271_common_probe’ [-Werror=implicit-function-declaration]
Move the function out of #if block.
Fixes: d6cf89ee07 ('ASoC: cs4271: claim reset GPIO in bus probe function')
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Daniel Mack <daniel@zonque.org>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
i) by the time DM core calls the postsuspend hook the dm_noflush flag
has been cleared. So the old thin_postsuspend did nothing. We need to
use the presuspend hook instead.
ii) There was a race between bios leaving DM core and arriving in the
deferred queue.
thin_presuspend now sets a 'requeue' flag causing all bios destined for
that thin to be requeued back to DM core. Then it requeues all held IO,
and all IO on the deferred queue (destined for that thin). Finally
postsuspend clears the 'requeue' flag.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The spin lock in requeue_io() was held for too long, allowing deadlock.
Don't worry, due to other issues addressed in the following "dm thin:
fix noflush suspend IO queueing" commit, this code was never called.
Fix this by taking the spin lock for a much shorter period of time.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Ideally a thin pool would never run out of data space; the low water
mark would trigger userland to extend the pool before we completely run
out of space. However, many small random IOs to unprovisioned space can
consume data space at an alarming rate. Adjust your low water mark if
you're frequently seeing "out-of-data-space" mode.
Before this fix, if data space ran out the pool would be put in
PM_READ_ONLY mode which also aborted the pool's current metadata
transaction (data loss for any changes in the transaction). This had a
side-effect of needlessly compromising data consistency. And retry of
queued unserviceable bios, once the data pool was resized, could
initiate changes to potentially inconsistent pool metadata.
Now when the pool's data space is exhausted transition to a new pool
mode (PM_OUT_OF_DATA_SPACE) that allows metadata to be changed but data
may not be allocated. This allows users to remove thin volumes or
discard data to recover data space.
The pool is no longer put in PM_READ_ONLY mode in response to the pool
running out of data space. And PM_READ_ONLY mode no longer aborts the
pool's current metadata transaction. Also, set_pool_mode() will now
notify userspace when the pool mode is changed.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
If a thin metadata operation fails the current transaction will abort,
whereby causing potential for IO layers up the stack (e.g. filesystems)
to have data loss. As such, set THIN_METADATA_NEEDS_CHECK_FLAG in the
thin metadata's superblock which:
1) requires the user verify the thin metadata is consistent (e.g. use
thin_check, etc)
2) suggests the user verify the thin data is consistent (e.g. use fsck)
The only way to clear the superblock's THIN_METADATA_NEEDS_CHECK_FLAG is
to run thin_repair.
On metadata operation failure: abort current metadata transaction, set
pool in read-only mode, and now set the needs_check flag.
As part of this change, constraints are introduced or relaxed:
* don't allow a pool to transition to write mode if needs_check is set
* don't allow data or metadata space to be resized if needs_check is set
* if a thin pool's metadata space is exhausted: the kernel will now
force the user to take the pool offline for repair before the kernel
will allow the metadata space to be extended.
Also, update Documentation to include information about when the thin
provisioning target commits metadata, how it handles metadata failures
and running out of space.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Joe Thornber <ejt@redhat.com>
If the open stateid could not be recovered, or the file locks were lost,
then we should fail the truncate() operation altogether.
Reported-by: Andy Adamson <andros@netapp.com>
Link: http://lkml.kernel.org/r/1393954269-3974-1-git-send-email-andros@netapp.com
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
