In some cases during heavy tx vdev stop-start
would timeout on vdev synchronization causing
traffic to stall for a few seconds.
Instead of stop-starting use a dedicated vdev
restart command and down vdevs explicitly before
doing so.
This gets rid of the synchronization
warnings/timeouts and makes channel switching
smoother during traffic.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When switching from one 5 GHz channel to another 5 GHz channel we need
to make sure BPHY is still in a reset. However to access BPHY register
we have to switch to 2 GHz mode for a moment. Otherwise this may result
in "Data bus error" (noticed by Hauke with BCM43224 connected to the
SoC).
Reported-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add lists of chipsets, so people can enable support for their device
easier (at least after checking lspci).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TDLS connections require dedicated flowrings. This patches adds
TDLS event handling and flowring creation/deletion based on these
events.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Msgbuf flow control was using a function to flow off and on which
was not supported without proptx enabled. Also flow control needs
to be handled per ifidx.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a pcie device gets reset then the low power modes l1 and l2
should be temporarily disabled.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch will add PCIe support. With this patch the PCIe chipsets
43602, 4354, 4356, 43567, and 43570 will be supported.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch will add the msgbuf protocol. This protocol is used by
the soon to be added new bus interface PCIe. Msgbuf is a protocol
where most data is and remains located on the host (driver) side
and transferred by DMA from and to device. Msgbuf is the protocol
which takes care of the signalling of the buffers between host and
device which identifies this DMA-able data.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The soon to be added protocol msgbuf requires information about
interface addressing mode and peer deletion. This patch adds the
necessary APIs to proto, implements dummy functions in BCDC and
adds calls to proto wherever necessary by wl_cfg80211.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit "c1b2053 brcmfmac: Make firmware path a module parameter"
introduced use of strcpy and strcat. The strcpy and strcat require
using null terminated strings and can cause out-of-bounds memory
access and subsequent corruption. This patch replaces these by
strncpy and strncat respectively to assure array boundaries are
not crossed.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Daniel Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Correct typo in the name of the type given to sizeof. Because it is the
size of a pointer that is wanted, the typo has no impact on compilation or
execution.
This problem was found using Coccinelle (http://coccinelle.lip6.fr/). The
semantic patch used can be found in message 0 of this patch series.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It has taken me a long long time to get the OOB interrupt working on the
AP6210 sdio wifi/bt module found on various Allwinner A20 boards. In the
end I found these magic register pokes in the cubietruck kernel tree:
7f08ba3956
This is also done for the bcm43362 in broadcom's internal/proprietary driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
[arend@broadcom.com: rebased changing BCM43362 chip id to fix compilation]
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not doing so, could fail on device probing when use_chanctx
module param is set to true.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It contains radio 0x2057 rev 14 just like a BCM43217, so it doesn't
require any magic. The main difference is that BCM4313 is 1x1:1.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcmfmac devices can use an out-of-band interrupt on a GPIO line.
Currently this is specified using platform data. Add support for
specifying out-of-band interrupt via device tree.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
[arend@broadcom.com: conditionalize more of-code, use driver debug routines]
Signed-off-by: Arend van Spriel <arend@broadcom.com>
[hdegoede@redhat.com: drop clk / reg_on gpio handling, as there is no consensus
on how to handle this yet]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Print sequence number, AMSDU_MORE flag and AC when additional
debug enabled in RX path. This is usefull for debugging purpose.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
A-MSDU 4addr frames weren't reconstructed properly
and in some cases this resulted in a warning:
br0: received packet on wlan0.sta1 with own address as source address
Since this was only related to A-MSDU it would
trigger when more intense traffic was generated.
Reported-by: Vu Hai NGUYEN <vh.nguyen@actiasodielec.fr>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
John W. Linville says:
====================
pull request: wireless-next 2014-07-25
Please pull this batch of updates intended for the 3.17 stream!
For the mac80211 bits, Johannes says:
"We have a lot of TDLS patches, among them a fix that should make hwsim
tests happy again. The rest, this time, is mostly small fixes."
For the Bluetooth bits, Gustavo says:
"Some more patches for 3.17. The most important change here is the move of
the 6lowpan code to net/6lowpan. It has been agreed with Davem that this
change will go through the bluetooth tree. The rest are mostly clean up and
fixes."
and,
"Here follows some more patches for 3.17. These are mostly fixes to what
we've sent to you before for next merge window."
For the iwlwifi bits, Emmanuel says:
"I have the usual amount of BT Coex stuff. Arik continues to work
on TDLS and Ariej contributes a few things for HS2.0. I added a few
more things to the firmware debugging infrastructure. Eran fixes a
small bug - pretty normal content."
And for the Atheros bits, Kalle says:
"For ath6kl me and Jessica added support for ar6004 hw3.0, our latest
version of ar6004.
For ath10k Janusz added a printout so that it's easier to check what
ath10k kconfig options are enabled. He also added a debugfs file to
configure maximum amsdu and ampdu values. Also we had few fixes as
usual."
On top of that is the usual large batch of various driver updates --
brcmfmac, mwifiex, the TI drivers, and wil6210 all get some action.
Rafał has also been very busy with b43 and related updates.
Also, I pulled the wireless tree into this in order to resolve a
merge conflict...
P.S. The change to fs/compat_ioctl.c reflects a name change in a
Bluetooth header file...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The 10.2 firmware is a successor of 10.1 firmware
(formerly identified as 10.x). Both share a lot
but have some slight ABI differences that need to
be taken care of.
The 10.2 firmware introduces some new features but
those can be added in subsequent patches. This
patch makes ath10k boot and work with 10.2 with
comparable functionality to 10.1.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Different firmware may support different numbers of
vdevs. Use value that is always out of range for all
firmware.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The 10.x firmware does not support IBSS mode at
all. It can't beacon and it crashes when trying to
scan.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware doesn't perform Rx reordering so it is
left to the host driver to do that.
Use mac80211 to perform reordering instead of
re-inventing the wheel.
This fixes TCP throughput issues in some
environments.
Reported-by: Denton Gentry <denton.gentry@gmail.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
We have interfaces. Remove the open coded cruft. Reduces text size
along with the code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: QCA ath9k Development <ath9k-devel@qca.qualcomm.com>
Cc: John W. Linville <linville@tuxdriver.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
This has been tested on 14e4:4328 (BCM4321), 14e4:432b (BCM4322),
14e4:4353 (BCM43224) and 14e4:4359 (BCM43228) which is an almost
complete list of 5 GHz capable device (only BCM43222 is missing).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We don't have all needed channel tables due to RE process for this
device.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This process requires sending some sample tone, so make sure we're
allowed to transmit first.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
So far we were assuming only A-PHY supports 5 GHz.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The dividend in do_div() is expected to be an unsigned 64-bit integer,
which leads to the following warning when building for 32-bit MIPS:
drivers/net/wireless/mac80211_hwsim.c: In function 'mac80211_hwsim_set_tsf':
drivers/net/wireless/mac80211_hwsim.c:664:98: warning: comparison of distinct pointer types lacks a cast [enabled by default]
data->bcn_delta = do_div(delta, bcn_int);
Since we care about the signedness of delta when adjusting tsf_offset
and bcm_delta, use the absolute value for the division and compare
the two timestamps to determine the sign.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If an aggregation session fails, frames still end up in the driver queue
with IEEE80211_TX_CTL_AMPDU set.
This causes tx for the affected station/tid to stall, since
ath_tx_get_tid_subframe returning packets to send.
Fix this by clearing IEEE80211_TX_CTL_AMPDU as long as no aggregation
session is running.
Cc: stable@vger.kernel.org
Reported-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The DCM condition was not checked well for channel switch in both AP and
station scenarios. Teardown was also not done for AP/GO DCM. Add the
missing checks.
Reported-by: Peer, Ilan <ilan.peer@intel.com>
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
It was possible to enter an endless loop while
processing a single pci copy engine pipe. This
could effectively render ath10k incapable of
responding to any requests.
An example case when this could happen is when
firmware generates a lot of events, e.g. spectral
scan phyerr via WMI.
Reported-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some radios may share the same ID and revision but differ by a version.
E.g. radio in BCM5357B0 is version 1 and requires specific handling.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Newer devices need different workarounds for cores 0 and 1.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add some missing ops and prepare for new devices support. This patch is
a great stability improvement for BCM43217. Earlier Tenda W322E used to
disconnect every 2 minutes (16 times over 30 minutes). With this fix I
got it running for 4 hours (with iperf) without any disconnection.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes handling channel 14 and adds code for BCM43217.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mmc_rescan will scan for non-removable cards only once, hence the card
will not be rediscovered.
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
