Add machine files for bf60x including head files, Kconfig/Makefile and board
file.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
do{...}while makes no sense in __ASSEMBLY__ code paths. now
kernels fail to build:
arch/blackfin/mach-bf561/atomic.S: Assembler messages:
arch/blackfin/mach-bf561/atomic.S:48: Error: syntax error. Input text
was do.
arch/blackfin/mach-bf561/atomic.S:48: Error:
arch/blackfin/mach-bf561/atomic.S:48: Error: syntax error. Input text
was }.
arch/blackfin/mach-bf561/atomic.S:48: Error:
arch/blackfin/mach-bf561/atomic.S:53: Error: syntax error. Input text
was do.
arch/blackfin/mach-bf561/atomic.S:53: Error:
arch/blackfin/mach-bf561/atomic.S:53: Error: syntax error. Input text
was }.
Signed-off-by: Bob Liu <lliubbo@gmail.com>
On IT8782F and IT8783F, some voltage input pins may be disabled. Don't create
sysfs attribute files if that is the case.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
The following build warning is seen in some configurations:
drivers/hwmon/ntc_thermistor.c: In function 'ntc_show_temp':
drivers/hwmon/ntc_thermistor.c:293: warning: 'temp' may be used uninitialized in this function
Fix the problem by re-arranging the code to overload return values with error
codes, and by avoiding error returns whenever possible.
Specifically,
Simplify lookup_comp() to not return an error. Instead, return i_low == i_high
if there is an exact match, or if the ohm value is outside the lookup table
range.
Modify get_temp_mC() to not return an error. Since it only returns an error
after lookup_comp() returned an error, this is quite straightforward after above
change.
Separate ntc_thermistor_read() into a function to read the resistor value (which
can return an error), and the call to get_temp_mC() which doesn't. Call the
functions directly from ntc_show_temp().
Code was tested using a test program, comparing the result of the old and new
versions of get_temp_mC() for resistor values between 0 and 2,000,000 ohm.
As a side effect, this patch reduces code size by approximately 400 bytes on
x86_64.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Donggeun Kim <dg77.kim@samsung.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
hwmon_device_register() never returns a NULL pointer in case of errors, but
an error value. Use it.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
This avoids memory leaks, and makes the code a bit simpler and smaller.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Remove unused defines AD7314_PD, AD7314_TEMP_SIGN, and ADT7301_TEMP_SIGN.
Rename AD7314_TEMP_OFFSET to the more appropriate AD7314_TEMP_SHIFT.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Jean Delvare <khali@linux-fr.org>
We don't need to duplicate if (res) checks if we're always running
one or the other.
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
We always register these two together, so move meter_rw_attrs into
meter_ro_attrs and use the same for both since we no longer have two
register_attr paths.
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Key off the attr->set method being present to set the sysfs attribute
as writable.
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Similar to how we do PCI/USB device id structs.
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
We don't need both, when we can just key the read/write off of the
presence of the .set member.
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
This patch converts the drivers in drivers/hwmon/* to use module_pci_driver()
macro which makes the code smaller and a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Clemens Ladisch <clemens@ladisch.de>
Cc: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
This patch fixes a bug in iscsit_allocate_iovecs() where iov_count was
incorrectly calculated using min(1UL, data_length / PAGE_SIZE) instead of
max(1UL, data_length / PAGE_SIZE), that ends up triggering an OOPs for
large block I/O when the SGL <-> iovec mapping exceeds the bogus iov_count
allocation size.
This is a regression introduced during the iscsi-target conversion back
to using core memory allocation here:
commit bfb79eac20
Author: Andy Grover <agrover@redhat.com>
Date: Tue Apr 3 15:51:29 2012 -0700
target/iscsi: Go back to core allocating data buffer for cmd
Cc: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We will soon be interpreting the layout (and chunksize etc) from
multiple places to support reshape. So split it out into separate
function.
Signed-off-by: NeilBrown <neilb@suse.de>
When RAID10 supports reshape it will need a 'previous' and a 'current'
geometry, so introduce that here.
Use the 'prev' geometry when before the reshape_position, and the
current 'geo' when beyond it. At other times, use both as
appropriate.
For now, both are identical (And reshape_position is never set).
When we use the 'prev' geometry, we must use the old data_offset.
When we use the current (And a reshape is happening) we must use
the new_data_offset.
Signed-off-by: NeilBrown <neilb@suse.de>
Some resync type operations need to act on the address space of the
device, others on the address space of the array.
This only affects RAID10, so it sets resync_max_sectors to the array
size (it defaults to the device size), and that is currently used for
resync only. However reshape of a RAID10 must be done against the
array size, not device size, so change code to use resync_max_sectors
for both the resync and the reshape cases.
This does not affect RAID5 or RAID1, just RAID10.
Signed-off-by: NeilBrown <neilb@suse.de>
Some code in raid1 and raid10 use sync_page_io to
read/write pages when responding to read errors.
As we will shortly support changing data_offset for
raid10, this function must understand new_data_offset.
So add that understanding.
Signed-off-by: NeilBrown <neilb@suse.de>
We will shortly be adding reshape support for RAID10 which will
require it having 2 concurrent geometries (before and after).
To make that easier, collect most geometry fields into 'struct geom'
and access them from there. Then we will more easily be able to add
a second set of fields.
Note that 'copies' is not in this struct and so cannot be changed.
There is little need to change this number and doing so is a lot
more difficult as it requires reallocating more things.
So leave it out for now.
Signed-off-by: NeilBrown <neilb@suse.de>
The important issue here is incorporating the different in data_offset
into calculations concerning when we might need to over-write data
that is still thought to be valid.
To this end we find the minimum offset difference across all devices
and add that where appropriate.
Signed-off-by: NeilBrown <neilb@suse.de>
As there can now be two different data_offsets - an 'old' and
a 'new' - we need to carefully choose between them.
Signed-off-by: NeilBrown <neilb@suse.de>
When reshaping we can avoid costly intermediate backup by
changing the 'start' address of the array on the device
(if there is enough room).
So as a first step, allow such a change to be requested
through sysfs, and recorded in v1.x metadata.
(As we didn't previous check that all 'pad' fields were zero,
we need a new FEATURE flag for this.
A (belatedly) check that all remaining 'pad' fields are
zero to avoid a repeat of this)
The new data offset must be requested separately for each device.
This allows each to have a different change in the data offset.
This is not likely to be used often but as data_offset can be
set per-device, new_data_offset should be too.
This patch also removes the 'acknowledged' arg to rdev_set_badblocks as
it is never used and never will be. At the same time we add a new
arg ('in_new') which is currently always zero but will be used more
soon.
When a reshape finishes we will need to update the data_offset
and rdev->sectors. So provide an exported function to do that.
Signed-off-by: NeilBrown <neilb@suse.de>
Currently a reshape operation always progresses from the start
of the array to the end unless the number of devices is being
reduced, in which case it progressed in the opposite direction.
To reverse a partial reshape which changes the number of devices
you can stop the array and re-assemble with the raid-disks numbers
reversed and it will undo.
However for a reshape that does not change the number of devices
it is not possible to reverse the reshape in the middle - you have to
wait until it completes.
So add a 'reshape_direction' attribute with is either 'forwards' or
'backwards' and can be explicitly set when delta_disks is zero.
This will become more important when we allow the data_offset to
change in a reshape. Then the explicit statement of what direction is
being used will be more useful.
This can be enabled in raid5 trivially as it already supports
reverse reshape and just needs to use a different trigger to request it.
Signed-off-by: NeilBrown <neilb@suse.de>
A flush request is usually issued in transaction commit code path, so
using GFP_KERNEL to allocate memory for flush request bio falls into
the classic deadlock issue.
This is suitable for any -stable kernel to which it applies as it
avoids a possible deadlock.
Cc: stable@vger.kernel.org
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
The following tightens the padding check from commit
c1412fce7e :
* Take into account combinations of consecutive Pad1 and PadN.
* Catch the corner case of when only padding is present in the
header, when the extention header length is 0 (i.e., 8 bytes).
In this case, the header would have exactly 6 bytes of padding:
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
: Next Header : Hdr Ext Len=0 : :
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ +
: Padding (Pad1 or PadN) :
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the ZTE (Vodafone) K3765-Z to the whitelist. This requires the
previous patch to make the whitelist with forced interface 4 generic
or the device fails to initialise. After applying this patch and
loading the Option driver without usb-modeswitch's bind all
interfaces trick, a wwan0 net interface and /dev/cdc-wdm0 device
file were created. Using Bjorn Mork's perl connection script a
connection was made to a mobile network using QMI and the network
interface's IPv4 address was configured OK.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the forced interface 4 whitelist to use the generic shared
binder instead of the Gobi specific one. Certain ZTE devices
(K3520-Z & K3765-Z) don't work with the Gobi version, but function
quite happily with the generic. This has been tested with the following
devices:
K3520-Z
K3565-Z
K3765-Z
K4505-Z
It hasn't been tested with the ZTE MF820D, which is the only other
device that uses this whitelist at present. Although Bjorn doesn't
expect any problems, any testing with that device would be appreciated.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Davis S. Miller wrote:
"
The way we do that now is overkill. We only needed to use the MMU
cache ops when we had sun4c around because sun4c lacked support for
the "flush" instruction.
But all sun4m and later chips have it so we can use it
unconditionally.
So in the per_cpu_patch() code, get rid of the cache ops invocation,
and instead execute a "flush %reg" after each of the instruction patch
assignments, where %reg is set to the address of the instruction that
was stored into.
Perhaps take the flushi() definition from asm/cacheflush_64.h and
place it into asm/cacheflush.h, then you can simply use that.
"
Implemented as per suggestion.
Moved run-time patching before we call paging_init(),
so helper methods in paging_init() may utilise run-time patching too.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We hang forever when trying to do run-time patching of instructions
identified by the cpuid_patch section
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Explicitly provide the first internal volume ID value in the comment for
UBI_INTERNAL_VOL_START. This allows developers who, when adding features
related to volume ids and observe unexpected very large volume ids, to grep
for the observed value in the source code and find out immediately that it is
expected behaviour.
Signed-off-by: Joel Reardon <reardonj@inf.ethz.ch>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Finally, rename the scan.c file. Now adding fastmap support won't look that
hacky anymore.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
This file is small and it does not make sense to have it separate from where
everything else lives, so merge it with ubi.h.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Rename the constant to UBI_UNKNOWN, for the same reason that we are going
to add nother attaching method and re-use the same data structures, so the
"SCAN" in the name becomes incorrect. I've also removed the "_EC" part because
Joel is going to use this constant for other fields in the attaching info data
structures.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Rename the 'attach_by_scanning()' function to 'ubi_attach()' and move it to
scan.c. Richard will plug his fastmap stuff there.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
We have a couple of initialization funcntionsn left which have "_scan" suffic -
rename them:
ubi_eba_init_scan() -> ubi_eba_init()
ubi_wl_init_scan() -> ubi_wl_init()
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
This patch amends commentaries in scan.[ch] to match the new logic. Reminder -
we did the restructuring to prepare the code for adding the fastmap. This patch
also renames a couple of functions - it was too difficult to separate out that
change and I decided that it is not too bad to have it in the same patch with
commentaries changes.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
