This patch fixes two problems in the claw driver identified by
static code analysis:
o Change in case differentiation of received sense codes
o Use correct data length in claw hard_start_xmit routine
Signed-off-by: Andrew H. Richter <richtera@us.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Ursula Braun <ursula.braun@de.ibm.com>
This patch fixes problems in the ctcm driver identified by
static code analysis:
o remove an unnecessary always true condition in ctcm_unpack_skb
o remove duplicate assignment in ctc_mpc_alloc_channel
o remove an unnecessary always true condition in ctcmpc_send_sweep_resp
o remove duplicate initialization in ctcmpc_unpack_skb
o shorten if condition in mpc_action_go_inop
o remove INOP event if mpc group is undefined in mpc_action_doxid7
Signed-off-by: Joel A. Fowler <fowlerja@us.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the receive code should tolerate any incoming garbage, it
should be protected against a potential wraparound when manipulating
length values within incoming data.
block_len is unsigned, so a too large subtraction will cause a
wraparound.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid kernel warning by using the correct hard_start_xmit return
code NETDEV_TX_BUSY for skb requeuing.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid kernel warnings by using the correct hard_start_xmit return
code NETDEV_TX_BUSY for skb requeuing.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid kernel warning by using the correct hard_start_xmit return
code NETDEV_TX_BUSY for skb requeuing.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lcs hard_start_xmit routine issued return codes other than
defined for this interface. Now lcs returns only either
NETDEV_TX_OK or NETDEV_TX_BUSY.
Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lcs uses low-level kernel_thread implementation.
All drivers should use <linux/kthread.h> API instead.
Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Pass pointer to buffer for IDENTIFY data to do_identify()
and try_to_identify().
* Un-static try_to_identify() and use it in ide_driveid_update().
* Rename try_to_identify() to ide_dev_read_id().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Clear drive IRQ after re-enabling local IRQs in ide_driveid_update()
to match try_to_identify().
Also remove superfluous local_irq_enable() call while at it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Defer classifying device type from do_identify() to do_probe().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
do_identify() marks EXABYTENEST device as non-present and frees
drive->id so enable_nest() has absolutely no chance of working.
The code was like this since at least 2.6.12-rc2 and nobody
has noticed so just remove broken EXABYTENEST support.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Doing kmalloc() in the middle of command execution is not only ugly
but leaves drive waiting to send data on kmalloc() failure. Fix it.
While at it:
* Unify error code paths.
* Fixup error message to be more useful and add missing KERN_ERR level.
* Rename 'stat' variable to 's'.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove superfluous <asm/intctl-regs.h> include.
* Remove no longer used SUPPORT_SLOW_DATA_PORTS define.
* Move defining SUPPORT_VLB_SYNC to <linux/ide.h>.
* Use __ide_mm_*() macros from <asm-generic/ide_iops.h>
(MN10300 uses only memory-mapped I/O).
* Remove <asm/ide.h>.
While at it:
* Remove superfluous SPARC64 #ifdef from <linux/ide.h>.
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Set ->irq explicitly in cs5520.c.
* Remove irq argument from ide_hw_configure().
* Remove pciirq argument from ide_pci_setup_ports().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Return 0 instead of dev->irq in ->init_chipset implementations.
* Fix ->init_chipset method to return 'int' value instead of
'unsigned int' one.
This fixes ->init_chipset handling for host drivers (cs5530, hpt366
and pdc202xx_new) for which it is possible for this method to fail.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This is now handled by core IDE PCI code.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Move handling of IDE_HFLAG[_FORCE]_LEGACY_IRQS from ide_init_port()
to ide_pci_init_{one,two}().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Core IDE PCI code takes care of assigning hwif->irq for both ports.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Core IDE PCI code takes care of assigning hwif->irq for both ports.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix ->init_hwif to check if IDE PCI controller is in compatibility
mode instead of checking for hwif->irq == 0.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add missing pci_get_legacy_ide_irq() implementation
before it becomes required by core IDE PCI code.
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Do some CodingStyle fixups in <linux/ide.h> while at it.
v2:
Add missing <linux/delay.h> include (reported by Stephen Rothwell).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix following checkpatch.pl warnings/errors:
- WARNING: space prohibited between function name and open parenthesis '('
- WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
- WARNING: line over 80 characters
- ERROR: trailing whitespace
- ERROR: space required before the open parenthesis '('
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move xfer mode tuning code to ide-xfer-mode.c.
* Add CONFIG_IDE_XFER_MODE config option to be selected by host drivers
that support xfer mode tuning.
* Add CONFIG_IDE_XFER_MODE=n static inline versions of ide_set_pio()
and ide_set_xfer_rate().
* Make IDE_TIMINGS and BLK_DEV_IDEDMA config options select IDE_XFER_MODE,
also add explicit selects for few host drivers that need it.
* Build/link ide-xfer-mode.o and ide-pio-blacklist.o (it is needed only
by ide-xfer-mode.o) only if CONFIG_IDE_XFER_MODE=y.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Factor out processing of special commands from ide_special_rq()
to ide_do_devset() and ide_do_park_unpark().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use elv_add_request() instead of __elv_add_request() in ide_do_drive_cmd().
* ide_do_drive_cmd() is used only in ide-{atapi,cd}.c so inline it there.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Move ide_dma_timeout_retry() to ide-dma.c and add static inline
version for CONFIG_BLK_DEV_IDEDMA=n.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Move drive_is_ready() to ide-io.c, then make it static.
Also make some minor CodingStyle fixups while at it.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* taskfile_load_raw() is used only by do_drive_set_taskfiles()
so inline it there.
While at it:
- rename 'args' variable to 'task'
- remove struct taskfile_array
- do ide_acpigtf check early
- use REGS_PER_GTF
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
