From Wang Zhenyu:
High queue depth was a problem for some targets so make queue_depth adjustable
From Mike Christie
Make default queue_depth a little lower
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From Wang Zhenyu:
data digest fix (the bug caused data corruption w/Wasabi StorageBuilder target)
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
from Wang Zhenyu:
Must check SCSI CMD and R2T response according to the spec
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From tomof@acm.org:
There is one more issue about Equallogic systems. They send
re-direction info with FIN. I think that the kernel module needs to
let iscsid to read data from the socket before killing it.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Must check only valid opcode bits.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Rather than print a list of targets at driver init time, print each
disabled target as we attempt to scan it.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The NVRAM for both Tekram and Symbios boards allows the user to set the
speed and width for individual targets. I took that code out in March
2004 when we introduced Domain Validation, but it seems there's still
a legitimate need for it in some configurations.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
sym_show_msg was almost a duplicate of scsi_print_msg, except not as
featureful. So use the common code instead.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Now that this constant has been added to dma-mapping.h, we don't need our
own definition
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The upper layer doesn't send these down since 2.4.x (or 2.6 in
practice), so no need to handle it. Inline sym_setup_data_pointers
into its only caller so we can fail gracefully in the case we'd get
one neverless.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Allocate the lcb in slave_alloc and free it in slave_destroy. This allows
us to remove all the code that checks to see if it's already been allocated.
From: Christoph Hellwig <hch@lst.de>
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The SYM_OPT_SNIFF_INQUIRY define is never set any more, and the
sym_sniff_inquiry() function doesn't exist
From: Christoph Hellwig <hch@lst.de>
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Transition driver to exclusively use the request_firmware()
interfaces to retrieve firmware-blobs from user-space. This
will be the default behaviour going forward until the
embedded firmware-binary images are removed from the
upstream kernel.
Upon request, the driver caches the firmware image until the
driver is unloaded.
NOTE: The option is present to allow the user to continue to
use the firmware-loader modules, but, should be considered
deprecated.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Rejections fixed up and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
None of the other domain validation messages have a trailing full stop,
so I don't see why this one should.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
patch below marks a few scsi core datastructures as const, so that they end up
in the .rodata section and don't cacheline share with things that get dirtied
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When kexec booting a kernel when the previous kernel did not
call ipr's shutdown method, the ipr adapter does not get
properly initialized, which can result in the ipr adapter
completing commands issued by the previous kernel. Fix ipr
to detect this scenario by reading the adapter's interrupt
mask register and the microprocessor interrupt register.
If the interrupt mask register indicates that interrupts
are enabled or the reset alert bit is set when the card is
probed, this means the card is in an unknown state and we
hard reset the card.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch fixes
- PCI ID overlap issue
- node name changed to 'megaraid_legacy'
I hope this patch addresses concerns brought by Daniel Drake.
Signed-off by: Seokmann Ju <seokmann.ju@enginio.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When we got a device only capable of async, we would zero out goal->period
which would cause us to try PPR negotiations. Leave goal->period alone,
and check goal->offset before doing PPR. Kudos to Daniel Forsgren for
figuring this out.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Let's put my money where my mouth is. Smaller code is almost always
faster, if only because a single I$ miss ends up leaving a lot of cycles
to make up for. And system software - kernels in particular - are known
for taking more cache misses than most other kinds.
On my random config, this made the kernel about 10% smaller, and lmbench
seems to say that it's pretty uniformly faster too. Your milage may vary.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ERR_SEVERITY item is defined as a 8 bits item in SAL documentation
($B.2.1 rev december 2003), but as an u16 in sal.h.
This has the side effect that current code in mca.c may not call
ia64_sal_clear_state_info() upon receiving corrected platform errors
if there are bits set in the validation byte. Reported by Xavier Bru.
Signed-off-by: Tony Luck <tony.luck@intel.com>
KOBJECT_UEVENT=n seems to be a common pitfall for udev users in 2.6.14 .
-mm already contains a bigger patch removing this option that is IMHO
too big for being applied now to 2.6.15-rc.
This patch simply allows KOBJECT_UEVENT=n only if EMBEDDED.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use sbp2_remove_device() to free FIFO and ORB DMAs in a failure case.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jody McIntyre <scjody@modernduck.com>
sbp2_create_command_orb() code cleanup:
- add two helper functions to reduce nesting depth
- omit the return value which was always ignored
- remove unnecessary declaration from sb2.h
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jody McIntyre <scjody@modernduck.com>
Print the number of IR and IT contexts which a hardware implements
as an informational log message when ohci1394 initializes.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jody McIntyre <scjody@modernduck.com>
Combined mode sucks. Especially when both libata and the legacy IDE
drivers try to drive ports on the same device, since that makes DMA
rather difficult.
This patch addresses the problem by allowing the user to control which
driver binds to the ports in a combined mode configuration. In many
cases, they'll probably want the libata driver to control both ports
since it can use DMA for talking with ATAPI devices (when
libata.atapi_enabled=1 of course). It also allows the user to get old
school behavior by letting the legacy IDE driver bind to both ports.
But neither is forced, the patch doesn't change current behavior unless
one of combined_mode=ide or combined_mode=libata is passed
on the boot line. Either of those options may require you to access
your devices via different device nodes (/dev/hd* in the ide case
and /dev/sd* in the libata case), though of course if you have udev
installed nicely you may not notice anything. :)
Let me know if the documentation is too cryptic, I'd be happy to expand
on it if necessary. I think most users will want to boot with
'combined_mode=libata' and add 'options libata atapi_enabled=1'
to their modules.conf to get good DVD playing and disk behavior
(haven't tested CD or DVD writing though).
I'd much rather things behave sanely by default (i.e. DMA for devices on
both ports), but apparently that's difficult given the various chip
bugs and hardware configs out there (not to mention that people's
drives may suddenly change from /dev/hdc to /dev/sdb), so this boot
option may be the correct long term fix.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Some hardware does not support the PACKET command at all.
Other hardware supports ATAPI, but the driver does something nasty such
as calling BUG() when an ATAPI command is issued.
For these such cases, we mark them with a new flag, ATA_FLAG_NO_ATAPI.
Initial version contributed by Ben Collins.
There is no user of qc->waiting left after ata_exec_internal()
changes. Kill the field.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
There is no user of ata_qc_wait_err() and ata_qc_complete_noop() after
ata_exec_internal() changes. Remove unused functions.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch converts all users of libata internal commands to use
ata_exec_internal().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch implements ata_exec_internal() function which performs
libata internal command execution. Previously, this was done by each
user by manually initializing a qc, issueing it, waiting for its
completion and handling errors. In addition to obvious code
factoring, using ata_exec_internal() fixes the following bugs.
* qc not freed on issue failure
* ap->qactive clearing could race with the next internal command
* race between timeout handling and irq
* ignoring error condition not represented in tf->status
Also, qc & hardware are not accessed anymore once it's completed,
making internal commands more conformant with general semantics.
ata_exec_internal() also makes it easy to issue internal commands from
multiple threads if that becomes necessary.
This patch only implements ata_exec_internal(). A following patch
will convert all users.
Signed-off-by: Tejun Heo <htejun@gmail.com>
--
Jeff, all patches have been regenerated against upstream branch as of
today. (575ab52a21)
Also, I took out a debug printk from ata_exec_internal (don't know how
that one got left there). Other than that, all patches are identical
to the previous posting.
Thanks. :-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The drawing function cfbfillrect does not work correctly when access is not
unsigned-long aligned. It manifests as extra lines of pixels that are not
complete drawn. Reversing the shift operator solves the problem, so I would
presume that this bug would manifest only on little endian machines. The
function cfbcopyarea may also have this bug.
Aligned access should present no problems.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In slow imageblit, the pixel value is shifted by a certain amount (dependent
on the bpp and endianness) for each iteration. This is inefficient. Better
do the shifting once before going into the loop.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Every framebuffer driver relies on the assumption that the set_par()
function of the driver is called before drawing functions and other
functions dependent on the hardware state are executed.
Whenever you switch from X to a framebuffer console for the very first
time, there is a chance that a broken X system has _not_ set the mode to
KD_GRAPHICS, thus the vt and framebuffer code executes a screen redraw and
several other functions before a set_par() is executed. This is believed
to be not a bug of linux but a bug of X/xdm. At least some X releases used
by SuSE and Debian show this behaviour.
There was a 2nd case, but that has been fixed by Antonino Daplas on
10-dec-2005.
This patch allows drivers to set a flag to inform fbcon_switch() that they
prefer a set_par() call on every console switch, working around the
problems caused by the broken X releases.
The flag will be used by the next release of cyblafb and might help other
drivers that assume a hardware state different to the one used by X.
As the default behaviour does not change, this patch should be acceptable
to everybody.
Signed-off-by: Knut Petersen <Knut_Petersen@t-online.de>
Acked-by: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Avoid calls to fb_pan_display when driver is suspended or not in text mode.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Fix fb_pan_display rejecting yoffsets that are valid if panning mode
is ywrap.
- Add more robust error checking in fb_pan_display specially since this
function is accessible by userland apps.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add hooks to save and restore the graphics state. These hooks are called in
fbcon_blank() when entering/leaving KD_GRAPHICS mode. This is needed by
savagefb at least so it can cooperate with savage_dri and by cyblafb.
State save/restoration can be full or partial.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
