When the config TDP level is not nominal (level = 0), the MSR values for
reading level 1 and level 2 ratios contain power in low 14 bits and actual
ratio bits are at bits [23:16]. The current processing for level 1 and
level 2 is wrong as there is no shift done to get actual ratio.
Fixes: 6a35fc2d6c (cpufreq: intel_pstate: get P1 from TAR when available)
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: 4.4+ <stable@vger.kernel.org> # 4.4+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If using IRQF_TRIGGER_FALLING, then there is a race here: if the reset
completes before we enable the IRQ, then CHG is already low and touch
will be broken.
This has been seen on Chromebook Pixel 2.
A workaround is to reconfig T18 COMMSCONFIG to enable the RETRIGEN bit
using mxt-app:
mxt-app -W -T18 44
mxt-app --backup
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
A wrong decoding of the touch coordinate message causes a wrong touch
ID. Touch ID for dual touch must be 0 or 1.
According to the actual Neonode nine byte touch coordinate coding,
the state is transported in the lower nibble and the touch ID in
the higher nibble of payload byte five.
Signed-off-by: Knut Wohlrab <Knut.Wohlrab@de.bosch.com>
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
commit c6f39257c9 ("mfd: twl6040: Use regmap for register cache")
did remove the private cache for the vibra control registers and replaced
access within twl6040_get_vibralr_status() by calls to regmap. This is OK,
as long as twl6040_get_vibralr_status() uses already cached values or is
not called from interrupt context. But we call this in vibra_play() for
checking that the vibrator is not configured for audio mode.
The result is a "BUG: scheduling while atomic" if the first use of the
twl6040 is a vibra effect, because the first fetch is by reading the
twl6040 registers through (blocking) i2c and not from the cache.
As soon as the regmap has cached the status, further calls are fine.
The solution is to move the condition to the work() function which
runs in context that can block.
The original code returns -EBUSY, but the return value of ->play()
functions is ignored anyways. Hence, we do not loose functionality
by not returning an error but just reporting the issue to INFO loglevel.
Tested-on: Pyra (omap5) prototype
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
ip6_route_output looks into different fields in the passed flowi6 structure,
yet cxgbi passes garbage in nearly all those fields. Zero the structure out
first.
Fixes: fc8d0590d9 ("libcxgbi: Add ipv6 api to driver")
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hello,
So, this ended up a lot simpler than I originally expected. I tested
it lightly and it seems to work fine. Petr, can you please test these
two patches w/o the lru drain drop patch and see whether the problem
is gone?
Thanks.
------ 8< ------
If charge moving is used, memcg performs relabeling of the affected
pages from its ->attach callback which is called under both
cgroup_threadgroup_rwsem and thus can't create new kthreads. This is
fragile as various operations may depend on workqueues making forward
progress which relies on the ability to create new kthreads.
There's no reason to perform charge moving from ->attach which is deep
in the task migration path. Move it to ->post_attach which is called
after the actual migration is finished and cgroup_threadgroup_rwsem is
dropped.
* move_charge_struct->mm is added and ->can_attach is now responsible
for pinning and recording the target mm. mem_cgroup_clear_mc() is
updated accordingly. This also simplifies mem_cgroup_move_task().
* mem_cgroup_move_task() is now called from ->post_attach instead of
->attach.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@kernel.org>
Debugged-and-tested-by: Petr Mladek <pmladek@suse.com>
Reported-by: Cyril Hrubis <chrubis@suse.cz>
Reported-by: Johannes Weiner <hannes@cmpxchg.org>
Fixes: 1ed1328792 ("sched, cgroup: replace signal_struct->group_rwsem with a global percpu_rwsem")
Cc: <stable@vger.kernel.org> # 4.4+
Since e93ad19d05 ("cpuset: make mm migration asynchronous"), cpuset
kicks off asynchronous NUMA node migration if necessary during task
migration and flushes it from cpuset_post_attach_flush() which is
called at the end of __cgroup_procs_write(). This is to avoid
performing migration with cgroup_threadgroup_rwsem write-locked which
can lead to deadlock through dependency on kworker creation.
memcg has a similar issue with charge moving, so let's convert it to
an official callback rather than the current one-off cpuset specific
function. This patch adds cgroup_subsys->post_attach callback and
makes cpuset register cpuset_post_attach_flush() as its ->post_attach.
The conversion is mostly one-to-one except that the new callback is
called under cgroup_mutex. This is to guarantee that no other
migration operations are started before ->post_attach callbacks are
finished. cgroup_mutex is one of the outermost mutex in the system
and has never been and shouldn't be a problem. We can add specialized
synchronization around __cgroup_procs_write() but I don't think
there's any noticeable benefit.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Li Zefan <lizefan@huawei.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: <stable@vger.kernel.org> # 4.4+ prerequisite for the next patch
This reverts the following three commits:
70af921db6799977d9aaf1705ec197
The feature was ill conceived, has terrible semantics, and has added
nothing but regressions to the already fragile ipv6 stack.
Fixes: f1705ec197 ("net: ipv6: Make address flushing on ifdown optional")
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting the kernel client with cephx disabled and then enabling cephx
and restarting userspace daemons can result in a crash:
[262671.478162] BUG: unable to handle kernel paging request at ffffebe000000000
[262671.531460] IP: [<ffffffff811cd04a>] kfree+0x5a/0x130
[262671.584334] PGD 0
[262671.635847] Oops: 0000 [#1] SMP
[262672.055841] CPU: 22 PID: 2961272 Comm: kworker/22:2 Not tainted 4.2.0-34-generic #39~14.04.1-Ubuntu
[262672.162338] Hardware name: Dell Inc. PowerEdge R720/068CDY, BIOS 2.4.3 07/09/2014
[262672.268937] Workqueue: ceph-msgr con_work [libceph]
[262672.322290] task: ffff88081c2d0dc0 ti: ffff880149ae8000 task.ti: ffff880149ae8000
[262672.428330] RIP: 0010:[<ffffffff811cd04a>] [<ffffffff811cd04a>] kfree+0x5a/0x130
[262672.535880] RSP: 0018:ffff880149aeba58 EFLAGS: 00010286
[262672.589486] RAX: 000001e000000000 RBX: 0000000000000012 RCX: ffff8807e7461018
[262672.695980] RDX: 000077ff80000000 RSI: ffff88081af2be04 RDI: 0000000000000012
[262672.803668] RBP: ffff880149aeba78 R08: 0000000000000000 R09: 0000000000000000
[262672.912299] R10: ffffebe000000000 R11: ffff880819a60e78 R12: ffff8800aec8df40
[262673.021769] R13: ffffffffc035f70f R14: ffff8807e5b138e0 R15: ffff880da9785840
[262673.131722] FS: 0000000000000000(0000) GS:ffff88081fac0000(0000) knlGS:0000000000000000
[262673.245377] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[262673.303281] CR2: ffffebe000000000 CR3: 0000000001c0d000 CR4: 00000000001406e0
[262673.417556] Stack:
[262673.472943] ffff880149aeba88 ffff88081af2be04 ffff8800aec8df40 ffff88081af2be04
[262673.583767] ffff880149aeba98 ffffffffc035f70f ffff880149aebac8 ffff8800aec8df00
[262673.694546] ffff880149aebac8 ffffffffc035c89e ffff8807e5b138e0 ffff8805b047f800
[262673.805230] Call Trace:
[262673.859116] [<ffffffffc035f70f>] ceph_x_destroy_authorizer+0x1f/0x50 [libceph]
[262673.968705] [<ffffffffc035c89e>] ceph_auth_destroy_authorizer+0x3e/0x60 [libceph]
[262674.078852] [<ffffffffc0352805>] put_osd+0x45/0x80 [libceph]
[262674.134249] [<ffffffffc035290e>] remove_osd+0xae/0x140 [libceph]
[262674.189124] [<ffffffffc0352aa3>] __reset_osd+0x103/0x150 [libceph]
[262674.243749] [<ffffffffc0354703>] kick_requests+0x223/0x460 [libceph]
[262674.297485] [<ffffffffc03559e2>] ceph_osdc_handle_map+0x282/0x5e0 [libceph]
[262674.350813] [<ffffffffc035022e>] dispatch+0x4e/0x720 [libceph]
[262674.403312] [<ffffffffc034bd91>] try_read+0x3d1/0x1090 [libceph]
[262674.454712] [<ffffffff810ab7c2>] ? dequeue_entity+0x152/0x690
[262674.505096] [<ffffffffc034cb1b>] con_work+0xcb/0x1300 [libceph]
[262674.555104] [<ffffffff8108fb3e>] process_one_work+0x14e/0x3d0
[262674.604072] [<ffffffff810901ea>] worker_thread+0x11a/0x470
[262674.652187] [<ffffffff810900d0>] ? rescuer_thread+0x310/0x310
[262674.699022] [<ffffffff810957a2>] kthread+0xd2/0xf0
[262674.744494] [<ffffffff810956d0>] ? kthread_create_on_node+0x1c0/0x1c0
[262674.789543] [<ffffffff817bd81f>] ret_from_fork+0x3f/0x70
[262674.834094] [<ffffffff810956d0>] ? kthread_create_on_node+0x1c0/0x1c0
What happens is the following:
(1) new MON session is established
(2) old "none" ac is destroyed
(3) new "cephx" ac is constructed
...
(4) old OSD session (w/ "none" authorizer) is put
ceph_auth_destroy_authorizer(ac, osd->o_auth.authorizer)
osd->o_auth.authorizer in the "none" case is just a bare pointer into
ac, which contains a single static copy for all services. By the time
we get to (4), "none" ac, freed in (2), is long gone. On top of that,
a new vtable installed in (3) points us at ceph_x_destroy_authorizer(),
so we end up trying to destroy a "none" authorizer with a "cephx"
destructor operating on invalid memory!
To fix this, decouple authorizer destruction from ac and do away with
a single static "none" authorizer by making a copy for each OSD or MDS
session. Authorizers themselves are independent of ac and so there is
no reason for destroy_authorizer() to be an ac op. Make it an op on
the authorizer itself by turning ceph_authorizer into a real struct.
Fixes: http://tracker.ceph.com/issues/15447
Reported-by: Alan Zhang <alan.zhang@linux.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Sage Weil <sage@redhat.com>
Commit 52cbae0127 ("toshiba_acpi: Change default Hotkey enabling value")
changed the hotkeys enabling value, as it was the same value Windows uses,
however, it turns out that the value tells the EC that the driver will now
take care of the hardware events like the physical RFKill switch or the
pointing device toggle button.
This patch reverts such commit by changing the default hotkey enabling
value to 0x09, which enables hotkey events only, making the hardware
buttons working again.
Fixes bugs 113331 and 114941.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Pull crypto fixes from Herbert Xu:
"This fixes a couple of regressions in the talitos driver that were
introduced back in 4.3.
The first bug causes a crash when the driver's AEAD functionality is
used while the second bug prevents its AEAD feature from working once
you get past the first bug"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: talitos - fix AEAD tcrypt tests
crypto: talitos - fix crash in talitos_cra_init()
to the clk-ti branch from the Linux clk tree for the ADPLL clock driver.
Otherwise things won't keep booting properly when we flip over to use
the clock driver instead of fixed clocks set up by the bootloader.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2Lew
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.6/dt-ti81xx-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Enable dm814x and dra62x clock driver. This branch has a dependency
to the clk-ti branch from the Linux clk tree for the ADPLL clock driver.
Otherwise things won't keep booting properly when we flip over to use
the clock driver instead of fixed clocks set up by the bootloader.
* tag 'omap-for-v4.6/dt-ti81xx-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Add clocks for dm814x ADPLL
Remove the final printk. All preceding output is already properly
newline-terminated and the printk isn't even KERN_CONT to begin with,
so it only adds one empty line to the log.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Needed for v2 of the device firmware, otherwise kernel will stuck for few
seconds and throw "usb_submit_urb(ctrl) failed: -1" early on system boot.
Signed-off-by: Nazar Mokrynskyi <nazar@mokrynskyi.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The way cpufreq_governor_start() initializes j_cdbs->prev_load is
questionable.
First off, j_cdbs->prev_cpu_wall used as a denominator in the
computation may be zero. The case this happens is when
get_cpu_idle_time_us() returns -1 and get_cpu_idle_time_jiffy()
used to return that number is called exactly at the jiffies_64
wrap time. It is rather hard to trigger that error, but it is not
impossible and it will just crash the kernel then.
Second, j_cdbs->prev_load is computed as the average load during
the entire time since the system started and it may not reflect the
load in the previous sampling period (as it is expected to).
That doesn't play well with the way dbs_update() uses that value.
Namely, if the update time delta (wall_time) happens do be greater
than twice the sampling rate on the first invocation of it, the
initial value of j_cdbs->prev_load (which may be completely off) will
be returned to the caller as the current load (unless it is equal to
zero and unless another CPU sharing the same policy object has a
greater load value).
For this reason, notice that the prev_load field of struct cpu_dbs_info
is only used by dbs_update() and only in that one place, so if
cpufreq_governor_start() is modified to always initialize it to 0,
it will make dbs_update() always compute the actual load first time
it checks the update time delta against the doubled sampling rate
(after initialization) and there won't be any side effects of it.
Consequently, modify cpufreq_governor_start() as described.
Fixes: 18b46abd00 (cpufreq: governor: Be friendly towards latency-sensitive bursty workloads)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
The cpufreq-dt-platdev driver supports creation of cpufreq-dt platform
device now, reuse that and remove similar code from platform code.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq-dt-platdev driver supports creation of cpufreq-dt platform
device now, reuse that and remove similar code from platform code.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq-dt-platdev driver supports creation of cpufreq-dt platform
device now, reuse that and remove similar code from platform code.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq-dt-platdev driver supports creation of cpufreq-dt platform
device now, reuse that and remove similar code from platform code.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch add rockchip's compatible string to the compat list and
remove similar code from platform code for supporting generic platdev
driver.
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq-dt-platdev driver supports creation of cpufreq-dt platform
device now, reuse that and remove similar code from platform code.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq-dt-platdev driver supports creation of cpufreq-dt platform
device now, reuse that and remove similar code from platform code.
Note that the complete routine imx27_dt_init() is removed as
of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
has same effect as a NULL .init_machine machine callback pointer.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq-dt-platdev driver supports creation of cpufreq-dt platform
device now, reuse that and remove similar code from platform code.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The machines array in cpufreq-dt-platdev is used only once at boot time
and so should be marked with __initconst, so that kernel can free up
memory used for it, if required.
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
opp core allows OPPs to be explicitly marked as shared from platform
code, in case of operating-point v1 bindings.
Though we do everything fine in that case, we don't set the flag in the
opp-table to indicate that the OPPs are shared. It works fine today as
the flag isn't used anywhere else in the core, but we should be doing
the right thing by marking it set.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Move dev_pm_opp_set_sharing_cpus() towards the end of the file. This
is required for better readability after the next patch is applied,
which adds dev_pm_opp_get_sharing_cpus().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
dev_pm_opp_set_sharing_cpus() doesn't do any DT specific stuff and its
declarations are added within the CONFIG_OF ifdef by mistake. Take them
out of that.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Few of the routines in cpu.c were missing these, add them.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Don't send -EINVAL and propagate what's received from _find_opp_table().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cooling device is registered by ready callback. It's also invoked while
system resuming from sleep (Enabling non-boot cpus). Thus cooling device
may be multiple registered. Matchable unregistration is added to exit
callback to fix this issue.
Signed-off-by: Jia Hongtao <hongtao.jia@nxp.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
.exit callback (qoriq_cpufreq_cpu_exit()) is also used during suspend.
So __exit macro should be removed or the function will be discarded.
Signed-off-by: Jia Hongtao <hongtao.jia@nxp.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When THERMAL_OF is undefined the cooling device messages should not be
shown. -ENOSYS is returned from of_cpufreq_cooling_register() when
THERMAL_OF is undefined.
Signed-off-by: Jia Hongtao <hongtao.jia@nxp.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add a function to cleanup at module exit and export
appropriate GPL string to enable moduler support
for the cppc_cpufreq driver.
Reported-by: Srinivas Pandruvada <srinivas.pandruvada@intel.com>
Signed-off-by: Ashwin Chaugule <ashwin.chaugule@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The result returned by pid_calc() is subtracted from current_pstate
(which is the P-State requested during the last period) in order to
obtain the target P-State for the current iteration.
However, current_pstate may not reflect the real current P-State of
the CPU. In particular, that P-State may be higher because of the
frequency sharing per module.
The theory is:
- The load is the percentage of time spent in C0 and is related to
the average P-State during the same period.
- The last requested P-State can be completely different than the
average P-State (because of frequency sharing or throttling).
- The P-State shift computed by the pid_calc is based on the load
computed at average P-State, so the shift must be relative to
this average P-State.
Using the average P-State instead of current P-State improves power
without significant performance penalty in cases when a task migrates
from one core to other core sharing frequency and voltage.
Performance and power comparison with this patch on Cherry Trail
platform using Android:
Benchmark ?Perf ?Power
FishTank 10.45% 3.1%
SmartBench-Gaming -0.1% -10.4%
SmartBench-Productivity -0.8% -10.4%
CandyCrush n/a -17.4%
AngryBirds n/a -5.9%
videoPlayback n/a -13.9%
audioPlayback n/a -4.9%
IcyRocks-20-50 0.0% -38.4%
iozone RR -0.16% -1.3%
iozone RW 0.74% -1.3%
Signed-off-by: Philippe Longepe <philippe.longepe@linux.intel.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On page unaligned frames, create_framevec forces get_vaddr_frames to
allocate an extra page at the end of the buffer. Under some
circumstances, this leads to -EINVAL on VIDIOC_QBUF.
E.g:
We have vm_a that vm_area that goes from 0x1000 to 0x3000. And a
frame that goes from 0x1800 to 0x2800, i.e. 2 pages.
frame_vector_create will be called with the following params:
get_vaddr_frames(0x1800, 2, write, 1, vec);
get_vaddr will allocate the first page after checking that the memory
0x1800-0x27ff is valid, but it will not allocate the second page because
the range 0x2800-0x37ff is out of the vm_a range. This results in
create_framevec returning -EFAULT
Error Trace:
[ 9083.793015] video0: VIDIOC_QBUF: 00:00:00.00000000 index=1,
type=vid-cap, flags=0x00002002, field=any, sequence=0,
memory=userptr, bytesused=0, offset/userptr=0x7ff2b023ca80, length=5765760
[ 9083.793028] timecode=00:00:00 type=0, flags=0x00000000,
frames=0, userbits=0x00000000
[ 9083.793117] video0: VIDIOC_QBUF: error -22: 00:00:00.00000000
index=2, type=vid-cap, flags=0x00000000, field=any, sequence=0,
memory=userptr, bytesused=0, offset/userptr=0x7ff2b07bc500, length=5765760
Also use true instead of 1 since that argument is a bool in the
get_vaddr_frames() prototype.
Fixes: 21fb0cb7ec ("[media] vb2: Provide helpers for mapping virtual addresses")
Reported-by: Albert Antony <albert@newtec.dk>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
[hans.verkuil@cisco.com: merged the 'bool' change into this patch]
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: <stable@vger.kernel.org> # for v4.3 and up
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When using a device is read/write mode, vb2 does not handle properly the
first select/poll operation.
The reason for this, is that when this code has been refactored, some of
the operations have changed their order, and now fileio emulator is not
started.
The reintroduced check to the core is enabled by a quirk flag, that
avoids this check by other subsystems like DVB.
Fixes: 49d8ab9fea ("media] media: videobuf2: Separate vb2_poll()")
Reported-by: Dimitrios Katsaros <patcherwork@gmail.com>
Cc: Junghak Sung <jh1009.sung@samsung.com>
Cc: <stable@vger.kernel.org> # for v4.5 and up
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The VSync polarity was negative instead of positive for the 4k CEA formats.
I probably copy-and-pasted these from the DMT 4k format, which does have a
negative VSync polarity.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Martin Bugge <marbugge@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.1 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Commit 9293fcfbc1
("udf: Remove struct ustr as non-needed intermediate storage"),
while getting rid of 'struct ustr', does not take any special care
of 'dstring' fields and effectively use fixed field length instead
of actual string length, encoded in the last byte of the field.
Also, commit 484a10f493
("udf: Merge linux specific translation into CS0 conversion function")
introduced checking of the length of the string being converted,
requiring proper alignment to number of bytes constituing each
character.
The UDF volume identifier is represented as a 32-bytes 'dstring',
and needs to be converted from CS0 to UTF8, while mounting UDF
filesystem. The changes in mentioned commits can in some cases
lead to incorrect handling of volume identifier:
- if the actual string in 'dstring' is of maximal length and
does not have zero bytes separating it from dstring encoded
length in last byte, that last byte may be included in conversion,
thus making incorrect resulting string;
- if the identifier is encoded with 2-bytes characters (compression
code is 16), the length of 31 bytes (32 bytes of field length minus
1 byte of compression code), taken as the string length, is reported
as an incorrect (unaligned) length, and the conversion fails, which
in its turn leads to volume mounting failure.
This patch introduces handling of 'dstring' encoded length field
in udf_CS0toUTF8 function, that is used in all and only cases
when 'dstring' fields are converted. Currently these cases are
processing of Volume Identifier and Volume Set Identifier fields.
The function is also renamed to udf_dstrCS0toUTF8 to distinctly
indicate that it handles 'dstring' input.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Jan Kara <jack@suse.cz>
fuse_get_user_pages() should return error or 0. Otherwise fuse_direct_io
read will not return 0 to indicate that read has completed.
Fixes: 742f992708 ("fuse: return patrial success from fuse_direct_io()")
Signed-off-by: Ashish Samant <ashish.samant@oracle.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
We want to skip reparenting a clock on turning on power domain, if we
do not have the parent yet. The parent is obtained when turning the
domain off. However due to a typo, the loop is continued on IS_ERR() of
clock being reparented, not on the IS_ERR() of the parent.
Theoretically this could lead to OOPS on first turn on of a power
domain, if there was no turn off before. Practically that should never
happen because all power domains are turned on by default (reset value,
bootloader does not turn off them usually) so the first action will be
always turn off.
Fixes: 29e5eea06b ("ARM: EXYNOS: Get current parent clock for power domain on/off")
Reported-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
After commit fbd40ea018 ("ipv4: Don't do expensive useless work
during inetdev destroy.") when deleting an interface,
fib_del_ifaddr() can be executed without any primary address
present on the dead interface.
The above is safe, but triggers some "bug: prim == NULL" warnings.
This commit avoids warning if the in_dev is dead
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Revert commit 0df35026c6 (cpufreq: governor: Fix negative idle_time
when configured with CONFIG_HZ_PERIODIC) that introduced a regression
by causing the ondemand cpufreq governor to misbehave for
CONFIG_TICK_CPU_ACCOUNTING unset (the frequency goes up to the max at
one point and stays there indefinitely).
The revert takes subsequent modifications of the code in question into
account.
Fixes: 0df35026c6 (cpufreq: governor: Fix negative idle_time when configured with CONFIG_HZ_PERIODIC)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=115261
Reported-and-tested-by: Timo Valtoaho <timo.valtoaho@gmail.com>
Cc: 4.5+ <stable@vger.kernel.org> # 4.5+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Saeed Mahameed says:
====================
mlx5 driver updates and fixes
Changes from V0:
- Dropped: ("net/mlx5e: Reset link modes upon setting speed to zero")
- Fixed compilation issue introduced to mlx5_ib driver.
- Rebased to df63719390 ('Revert "Prevent NUll pointer dereference with two PHYs on cpsw"')
This series has few bug fixes for mlx5 core and ethernet driver.
Eli fixed a wrong static local variable declaration in flow steering API.
Majd added the support of ConnectX-5 PF and VF and added the support
for kernel shutdown pci callback for more robust reboot procedures.
Maor fixed a soft lockup in flow steering.
Rana fixed a wrog speed define in mlx5 EN driver.
I also had the chance to introduce some bug fixes in mlx5 EN mtu
reporting and handling.
For -stable:
net/mlx5_core: Fix soft lockup in steering error flow
net/mlx5e: Device's mtu field is u16 and not int
net/mlx5e: Fix minimum MTU
net/mlx5e: Use vport MTU rather than physical port MTU
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces kexec support for mlx5.
When switching kernels, kexec() calls shutdown, which unloads
the driver and cleans its resources.
In addition, remove unregister netdev from shutdown flow. This will
allow a clean shutdown, even if some netdev clients did not release their
reference from this netdev. Releasing The HW resources only is enough as
the kernel is shutting down
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Haggai Abramovsky <hagaya@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The static is not required and breaks re-entrancy if it will be required.
Fixes: 2530236303 ("net/mlx5_core: Flow steering tree initialization")
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set and report vport MTU rather than physical MTU,
Driver will set both vport and physical port mtu and will
rely on the query of vport mtu.
SRIOV VFs have to report their MTU to their vport manager (PF),
and this will allow them to work with any MTU they need
without failing the request.
Also for some cases where the PF is not a port owner, PF can
work with MTU less than the physical port mtu if set physical
port mtu didn't take effect.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
