This change updates the ixgbe driver to use __netdev_pick_tx instead of
the current logic it is using to select a queue. The main result of this
change is that ixgbe can now fully support XPS, and in the case of non-FCoE
enabled configs it means we don't need to have our own ndo_select_queue.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Reviewed-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change adds support for ixgbe to configure the XPS queue mapping on
load. The result of this change is that on open we will now be resetting
the number of Tx queues, and then setting the default configuration for XPS
based on if ATR is enabled or disabled.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Reviewed-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of adjusting the FCoE and Flow director limits based on the number
of CPUs we can define them much sooner. This allows the user to come
through later and adjust them once we have updated the code to support the
set_channels ethtool operation.
I am still allowing for FCoE and RSS queues to be separated if the number
queues is less than the number of CPUs. This essentially treats the two
groupings like they are two separate traffic classes.
In addition I am changing the initialization to use the MAX_TX/RX_QUEUES
defines instead of trying to compute the value as it will be possible in
upcoming patches for the user to request the maximum number of queues.
I have also updated things so that the upper limit on queues is exactly 63
instead of allowing it to go up to 64. The reason for this change is to
address the fact thqt the driver only supports up to 63 queue vectors since
the hardware supports 64 MSI-X vectors, but one must be reserved for "other"
causes.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On several machines with i350 adapters the ethtool offline self-test sometimes
fails. This happens because link auto negotiation may take longer than the
timeout of 4 seconds. Increasing the timeout by 1 seconds resolves the issue.
Output from a failing i350 offline self-test:
while [ 1 ]; do ethtool -t eth2 offline; done
The test result is PASS
The test extra info:
Register test (offline) 0
Eeprom test (offline) 0
Interrupt test (offline) 0
Loopback test (offline) 0
Link test (on/offline) 0
The test result is FAIL
The test extra info:
Register test (offline) 0
Eeprom test (offline) 0
Interrupt test (offline) 0
Loopback test (offline) 0
Link test (on/offline) 1
The test result is PASS
The test extra info:
Register test (offline) 0
Eeprom test (offline) 0
Interrupt test (offline) 0
Loopback test (offline) 0
Link test (on/offline) 0
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to address several race issues that become possible
because next_to_watch could possibly be set to a value that shows that the
descriptor is done when it is not. In order to correct that we instead make
next_to_watch a pointer that is set to NULL during cleanup, and set to the
eop_desc after the descriptor rings have been written.
To enforce proper ordering the next_to_watch pointer is not set until after
a wmb writing the values to the last descriptor in a transmit. In order to
guarantee that the descriptor is not read until after the eop_desc we use the
read_barrier_depends which is only really necessary on the alpha architecture.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Current e1000e driver doesn't tell nothing when Link Speed is downgraded due to
SmartSpeed. As a result, users suspect that there is something wrong with
NIC. If the cause of it is SmartSpeed, there is no means to replace NIC. This
patch make e1000e notify users that SmartSpeed worked.
Signed-off-by: Koki Sanagi <sanagi.koki@jp.fujitsu.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fixes whitespace issues, such as lines exceeding 80 chars, needless blank
lines and the use of spaces where tabs are needed. In addition, fix
multi-line comments to align with the networking standard.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tegra only supports, and always enables, device tree. Remove all ifdefs
and runtime checks for DT support from the driver. Platform data is
therefore no longer required. Delete the header that defines it, and
rework the driver to parse the device tree directly into struct
tegra_kbc.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
To properly setup event parameters for emulated events, pass
the appropriate flag to the slot initialization function. Also,
all MT-related events should be setup before initialization.
Incidentally, this solves the issue of doubly filtered pointer
events.
Reported-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The pointer emulation events are derived from contact values that
have already been filtered, so send the emulated events as is.
Reported-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make the constants referring to range and bandwidth public so they can
be used when initializing the platform data fields in the platform code.
Fix also some comments regarding the unit of measurement to use for the
range and bandwidth fields, the values are not actually expected to be
in G or HZ, the code in bma150.c just uses the BMA150_RANGE_xxx and
BMA150_BW_xxx constants like they are with no translation from actual
values in G or HZ.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Antonio Ospite <ao2@amarulasolutions.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When PM_RUNTIME is not defined, pm_runtime_get_sync() returns 1, see
include/linux/pm_runtime.c::__pm_runtime_resume(), and the check of the
return value was overlooking this, in this case bma150_open() would
return 1 which is not expected by upper layers.
Maybe the check for != -ENOSYS (Function not implemented) was meant to
cover this, but pm_runtime_get_sync() does not return this value.
For now fix the issue locally by checking explicitly for negative return
values.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Antonio Ospite <ao2@amarulasolutions.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
As the number of iovecs in a send request is already limited within
UIO_MAXIOV(i.e. 1024) in __sys_sendmsg(), it's unnecessary to check it
again in TIPC stack.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Change overload control to be purely byte-based, using
sk->sk_rmem_alloc as byte counter, and compare it to a calculated
upper limit for the socket receive queue.
For all connection messages, irrespective of message importance,
the overload limit is set to a constant value (i.e, 67MB). This
limit should normally never be reached because of the lower
limit used by the flow control algorithm, and is there only
as a last resort in case a faulty peer doesn't respect the send
window limit.
For datagram messages, message importance is taken into account
when calculating the overload limit. The calculation is based
on sk->sk_rcvbuf, and is hence configurable via the socket option
SO_RCVBUF.
Cc: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
When intel_pstate is configured into the kernel it will become the
preferred scaling driver for processors that it supports. Allow the
user to override this by adding:
intel_pstate=disable
on the kernel command line.
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Load order is important in order for intel_pstate to take over as the
default scaling driver from acpi-cpufreq.
If both are built-in, acpi-cpufreq uses late_initcall() and
intel_pstate uses device_initcall() so it will be able to register as
the scaling before acpi-cpufreq for the processors supported by
intel_pstate.
If acpi-cpufreq is built as a module then intel_pstate still gets
first option to become the scaling driver.
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The tipc function discard_rx_queue() is just a duplicated
implementation of __skb_queue_purge(). Remove the former
and directly invoke __skb_queue_purge().
In doing so, the underscores convey to the code reader, more
information about the current locking state that is assumed.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
After commit 3c294cb3 "tipc: remove the bearer congestion mechanism",
we try to grab the broadcast bearer lock when sending multicast
messages over the broadcast link. This will cause an oops because
the lock is never initialized. This is an old bug, but the lock
was never actually used before commit 3c294cb3, so that why it was
not visible until now. The oops will look something like:
BUG: spinlock bad magic on CPU#2, daemon/147
lock: bcast_bearer+0x48/0xffffffffffffd19a [tipc],
.magic: 00000000, .owner: <none>/-1, .owner_cpu: 0
Pid: 147, comm: daemon Not tainted 3.8.0-rc3+ #206
Call Trace:
spin_dump+0x8a/0x8f
spin_bug+0x21/0x26
do_raw_spin_lock+0x114/0x150
_raw_spin_lock_bh+0x19/0x20
tipc_bearer_blocked+0x1f/0x40 [tipc]
tipc_link_send_buf+0x82/0x280 [tipc]
? __alloc_skb+0x9f/0x2b0
tipc_bclink_send_msg+0x77/0xa0 [tipc]
tipc_multicast+0x11b/0x1b0 [tipc]
send_msg+0x225/0x530 [tipc]
sock_sendmsg+0xca/0xe0
The above can be triggered by running the multicast demo program.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We no longer need to use mac_len, lets cleanup things.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to implement empty suspend/resume callbacks if there is nothing
to do during suspend/resume. The drivers will behave the same with no callbacks
or empty callbacks during suspend/resume.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This pacth fixes the parsing of the eee_timer driver parameter.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
This series contains updates to igb and ixgbe. Most of the changes
are against igb, except for one patch against ixgbe.
There are 3 igb fixes from Carolyn which were reported by Dan
Carpenter which resolve issues found in the get_i2c_client(). Alex
does some cleanup of the igb driver to match similar functionality
in ixgbe on transmit. Alex also makes it so that we can enable the use
of build_skb for cases where jumbo frames are disabled. The advantage
to this is that we do not have to perform a memcpy to populate the header
and as a result we see a significant performance improvement.
Akeem provides 4 patches to initialize function pointers and do a
re-factoring of the function pointers in igb_get_variants() to assist
with driver debugging.
The ixgbe patch comes from Emil to reshuffle the switch/case structure
of the flag assignment to allow for the flags to be set for each MAC
type separately. This is needed for new hardware that does not have feature
parity with older hardware.
v2: updated patches 4 & 5 based on feedback from Ben Hutchings and Eric
Dumazet
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Following patch adds GRE protocol offload handler so that
skb_gso_segment() can segment GRE packets.
SKB GSO CB is added to keep track of total header length so that
skb_segment can push entire header. e.g. in case of GRE, skb_segment
need to push inner and outer headers to every segment.
New NETIF_F_GRE_GSO feature is added for devices which support HW
GRE TSO offload. Currently none of devices support it therefore GRE GSO
always fall backs to software GSO.
[ Compute pkt_len before ip_local_out() invocation. -DaveM ]
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function will be used in next GRE_GSO patch. This patch does
not change any functionality. It only exports skb_mac_gso_segment()
function.
[ Use skb_reset_mac_len() -DaveM ]
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
with older hypervisor stacks, such as Xen 4.1.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iQEcBAABAgAGBQJRHZ7eAAoJEFjIrFwIi8fJZ+sH/ieMkzdBB6aqbFMcNr7mkfBo
i3swjO2JQI7REYIHfKEVoR3IgHfqKEuABdeEQrceE0XqDepFh84YiKGI2QpPRWEA
903vUV4DXVdcBrypbL45tSFZ1Jxsrzx+F7WfV/f9WHyeiwOyaZTGVQH0VuOzpcum
RvPTT7MmC7g8MJDi66SDYBaX/pBQzifQ81nMWWjXNw0w4CwWX7le1cScZEP42MR6
jTEHzYMLDojdO+2aQM5pt/0CGI5tzBHtX5nNRl6tovlPI3ckknYYx6a7RfxkfZzF
IkMIuGS32yLfsswPPIiMs47/Qgiq3BN6eSTJXMZKUwQokL9yEs8LodcnRDYfgyQ=
=fqcJ
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.8-rc7-tag-two' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull xen fixes from Konrad Rzeszutek Wilk:
"Two fixes:
- A simple bug-fix for redundant NULL check.
- CVE-2013-0228/XSA-42: x86/xen: don't assume %ds is usable in
xen_iret for 32-bit PVOPS
and two reverts:
- Revert the PVonHVM kexec. The patch introduces a regression with
older hypervisor stacks, such as Xen 4.1."
* tag 'stable/for-linus-3.8-rc7-tag-two' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
Revert "xen PVonHVM: use E820_Reserved area for shared_info"
Revert "xen/PVonHVM: fix compile warning in init_hvm_pv_info"
xen: remove redundant NULL check before unregister_and_remove_pcpu().
x86/xen: don't assume %ds is usable in xen_iret for 32-bit PVOPS.
As reported by Klaus Schmidinger:
"In VDR I use an ioctl() call with FE_READ_UNCORRECTED_BLOCKS on a
device (using stb0899). After this call I check 'errno' for
EOPNOTSUPP to determine whether this device supports this call. This
used to work just fine, until a few months ago I noticed that my
devices using stb0899 didn't display their signal quality in VDR's OSD
any more. After further investigation I found that
ioctl(FE_READ_UNCORRECTED_BLOCKS) no longer returns EOPNOTSUPP, but
rather ENOTTY. And since I stop getting the signal quality in case
any unknown errno value appears, this broke my signal quality query
function."
While the changes reflect what is there at:
http://comments.gmane.org/gmane.linux.kernel/1235728
it does cause regression on userspace. So, revert it to stop the
damage.
This reverts commit 177ffe506c ("[media] dvb_frontend: return -ENOTTY
for unimplement IOCTL").
Reported-by: Klaus Schmidinger <Klaus.Schmidinger@tvdr.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This function will be used in next GRE_GSO patch. This patch does
not change any functionality.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Pull sparc fixes from David Miller:
"A couple small fixes for sparc including some THP brown-paper-bag
material:
1) During the merging of all the THP support for various
architectures, sparc missed adding a
HAVE_ARCH_TRANSPARENT_HUGEPAGE to it's Kconfig, oops.
2) Sparc needs to be mindful of hugepages in get_user_pages_fast().
3) Fix memory leak in SBUS probe, from Cong Ding.
4) The sunvdc virtual disk client driver has a test of the bitmask of
vdisk server supported operations which was off by one bit"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sunvdc: Fix off-by-one in generic_request().
sparc64: Fix get_user_pages_fast() wrt. THP.
sparc64: Add missing HAVE_ARCH_TRANSPARENT_HUGEPAGE.
sparc: kernel/sbus.c: fix memory leakage
Pull one more x86 fix from Peter Anvin:
"Sigh. One more patch in the "please don't brick my Samsung" series"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi: Clear EFI_RUNTIME_SERVICES rather than EFI_BOOT by "noefi" boot parameter
Hotplug
PCI/PM: Clean up PME state when removing a device
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=zdXb
-----END PGP SIGNATURE-----
Merge tag '3.8-pci-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fix from Bjorn Helgaas:
"This is another fix for v3.8. It fixes an oops that happens when a
Thunderbolt adapter is unplugged (remove device, poll for PME events
on no-longer-existing device, oops)."
* tag '3.8-pci-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI/PM: Clean up PME state when removing a device
omapdss)
* fix DPI displays on OMAP3630 (OMAPDSS: add FEAT_DPI_USES_VDDS_DSI to
omap3630_dss_feat_list)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=eJF5
-----END PGP SIGNATURE-----
Merge tag 'omapdss-for-3.8-rc8' of git://gitorious.org/linux-omap-dss2/linux
Pull omapdss fixes from Tomi Valkeinen:
"It'd be great if these two late fixes would still make it into 3.8.
The other one fixes ARM kernel compilation when using 'allyesconfig',
and the other makes DPI displays function again on OMAP3630 boards:
- Fix ARM compilation with "allyesconfig" (omapdrm: fix the
dependency to omapdss)
- fix DPI displays on OMAP3630 (OMAPDSS: add FEAT_DPI_USES_VDDS_DSI
to omap3630_dss_feat_list)"
* tag 'omapdss-for-3.8-rc8' of git://gitorious.org/linux-omap-dss2/linux:
omapdrm: fix the dependency to omapdss
OMAPDSS: add FEAT_DPI_USES_VDDS_DSI to omap3630_dss_feat_list
Pull i2c maintainer info update from Wolfram Sang:
"Since my old email and repos are not working anymore, and this already
caused some confusion, I think a MAINTAINERS update for 3.8 is
helpful. So, people trying I2C with the new kernel can properly reach
me and find my repos."
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
MAINTAINERS: change my email and repos
Several tracepoints are using STA_PR_FMT where STA_PR_ARG should be
used, resulting in messages like "phy0 sta:ARG TYPE NOT FIELD BUT 1".
Change these to STA_PR_ARG.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds the definition for the cldvfs function for Tegra114 pinctrl
support. This is based on work by Pritesh Raithatha.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Before the device is opened, the carrier state should be off. It
will not race with the link interrupt if we set it before calling
register_netdev().
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't set the default size to 128K if it is 5762. Instead, rely on the
size we obtain from NVRAM location 0xf0.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This chip supports Energy Efficient Ethernet. The existing code only
supports a smaller set of devices with 5718 PCI ID. Expand support for
all devices with the same 5717 B0 chip ID.
Signed-off-by: Michael Chan <mchan@broadocm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch also adds a couple of fixes
- For the 57766 and non Ax versions of 57765, bootcode needs to setup
the PCIE Fast Training Sequence (FTS) value to prevent transmit hangs.
Unfortunately, it does not have enough room in the selfboot case (i.e.
devices with no NVRAM). The driver needs to implement this.
- For performance reasons, the 2k DMA engine mode on the 57766 should
be enabled and dma size limited to 2k for standard sized packets.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since mesh powersaving was added, pending bcast/mcast frames may go out the
CAB queue now. Unfortunately, the queue was only set up for AP mode, so we
would try to tx on the IEEE80211_INVAL_HW_QUEUE. Allow cab_queue for mesh
interfaces as well.
Fixes the following warning (or crash without MAC80211_VERBOSE_DEBUG):
WARNING: at net/mac80211/tx.c:1223 __ieee80211_tx+0x162/0x35f [mac80211]()
Modules linked in: mac80211_hwsim mac80211 cfg80211 [...]
Pid: 3085, comm: avahi-daemon Tainted: G W 3.8.0-rc1+ #377
Call Trace:
[<ffffffff81045c20>] warn_slowpath_common+0x83/0x9c
[<ffffffff81045c53>] warn_slowpath_null+0x1a/0x1c
[<ffffffffa083aef0>] __ieee80211_tx+0x162/0x35f [mac80211]
[<ffffffffa083cb1d>] ieee80211_tx+0xd3/0xf9 [mac80211]
[<ffffffffa083cc0f>] ieee80211_xmit+0xcc/0xd5 [mac80211]
[<ffffffffa083db59>] ieee80211_subif_start_xmit+0xc53/0xcd8 [mac80211]
[<ffffffff81319acd>] dev_hard_start_xmit+0x259/0x3ce
[<ffffffff81333d6b>] sch_direct_xmit+0x74/0x17d
[<ffffffff8131a0b1>] dev_queue_xmit+0x230/0x414
[<ffffffff8134877a>] ip_finish_output2+0x348/0x3aa
[<ffffffff81349029>] ip_finish_output+0x6c/0x71
[<ffffffff81349046>] NF_HOOK_COND.constprop.44+0x18/0x58
[<ffffffff8134a03a>] ip_mc_output+0x134/0x13c
[<ffffffff8134835a>] dst_output+0x18/0x1c
[<ffffffff81349a24>] ip_local_out+0x20/0x24
[<ffffffff8134a8cf>] ip_send_skb+0x16/0x3c
[<ffffffff8136bfba>] udp_send_skb+0x254/0x2b9
[<ffffffff8136c85e>] udp_sendmsg+0x5a8/0x7d4
Signed-off-by: Bob Copeland <bob@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
. Fix cleanup in case of kzalloc failure, from Daniel Baluta.
. Limit unwind support to x86 archs, fix from Jiri Olsa.
. Initial GTK+ annotate browser, from Namhyung Kim.
. Fix build with bison 2.3 and older, from Vinson Lee.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)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=lo/L
-----END PGP SIGNATURE-----
Merge tag 'perf-core-for-mingo' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/core
Pull perf/core improvements and fixes from Arnaldo Carvalho de Melo:
* Fix cleanup in case of kzalloc failure, from Daniel Baluta.
* Limit unwind support to x86 archs, fix from Jiri Olsa.
* Initial GTK+ annotate browser, from Namhyung Kim.
* Fix build with bison 2.3 and older, from Vinson Lee.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
There's various code with strange indentation,
questionable loop and locking constructs, etc.
The bigger change is moving the "sdata" argument
to the first argument of all functions, like all
other mac80211 functions that have one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* 'next/cpufreq-exynos' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
cpufreq: exynos: Fix hang in pm handler due to frequency mismatch
cpufreq: exynos: Initialize return variable
cpufreq: exynos: Fix unsigned variable being checked for negative value
cpufreq: exynos: Get booting freq value in exynos_cpufreq_init
cpufreq: exynos: Show list of available frequencies
cpufreq: exynos: Add missing static
cpufreq: exynos: Split exynos_target function into two functions
cpufreq: exynos: Use APLL_FREQ macro for cpu divider value
cpufreq: exynos: Check old & new frequency early
cpufreq: exynos: Remove unused variable & IS_ERR
* pm-cpufreq: (55 commits)
cpufreq / intel_pstate: Fix 32 bit build
cpufreq: conservative: Fix typos in comments
cpufreq: ondemand: Fix typos in comments
cpufreq: exynos: simplify .init() for setting policy->cpus
cpufreq: kirkwood: Add a cpufreq driver for Marvell Kirkwood SoCs
cpufreq/x86: Add P-state driver for sandy bridge.
cpufreq_stats: do not remove sysfs files if frequency table is not present
cpufreq: Do not track governor name for scaling drivers with internal governors.
cpufreq: Only call cpufreq_out_of_sync() for driver that implement cpufreq_driver.target()
cpufreq: Retrieve current frequency from scaling drivers with internal governors
cpufreq: Fix locking issues
cpufreq: Create a macro for unlock_policy_rwsem{read,write}
cpufreq: Remove unused HOTPLUG_CPU code
cpufreq: governors: Fix WARN_ON() for multi-policy platforms
cpufreq: ondemand: Replace down_differential tuner with adj_up_threshold
cpufreq / stats: Get rid of CPUFREQ_STATDEVICE_ATTR
cpufreq: Don't check cpu_online(policy->cpu)
cpufreq: add imx6q-cpufreq driver
cpufreq: Don't remove sysfs link for policy->cpu
cpufreq: Remove unnecessary use of policy->shared_type
...
* acpi-cleanup: (21 commits)
ACPI / hotplug: Fix concurrency issues and memory leaks
ACPI: Remove the use of CONFIG_ACPI_CONTAINER_MODULE
ACPI / scan: Full transition to D3cold in acpi_device_unregister()
ACPI / scan: Make acpi_bus_hot_remove_device() acquire the scan lock
ACPI: Drop the container.h header file
ACPI / Documentation: refer to correct file for acpi_platform_device_ids[] table
ACPI / scan: Make container driver use struct acpi_scan_handler
ACPI / scan: Remove useless #ifndef from acpi_eject_store()
ACPI: Unbind ACPI drv when probe failed
ACPI: sysfs eject support for ACPI scan handlers
ACPI / scan: Follow priorities of IDs when matching scan handlers
ACPI / PCI: pci_slot: replace printk(KERN_xxx) with pr_xxx()
ACPI / dock: Fix acpi_bus_get_device() check in drivers/acpi/dock.c
ACPI / scan: Clean up acpi_bus_get_parent()
ACPI / platform: Use struct acpi_scan_handler for creating devices
ACPI / PCI: Make PCI IRQ link driver use struct acpi_scan_handler
ACPI / PCI: Make PCI root driver use struct acpi_scan_handler
ACPI / scan: Introduce struct acpi_scan_handler
ACPI / scan: Make scanning of fixed devices follow the general scheme
ACPI: Drop device start operation that is not used
...
