In iwlmvm firmwares, the Byte count written in the scheduler
byte count table is in DWORDs and not in bytes.
We should check that this value fits in the 12 bits and
the value can be either in bits of in DWORD or bytes
depending on the firmware. Check the value after the
translation to DWORDs is done (if needed).
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In a few places, we were disabling interrupts but didn't
make sure that the interrupt handler has finished running.
Add calls to synchronize_irq() to ensure we finish handling
the interrupts before we free resources or other things that
could lead to a crash if the interrupt were to be handled
later.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When the firmware crashes, we can't expect the Tx queues to
progress. Cancel their timer.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Since the time-event is sent with the immediate flag set, there is
no need to sample the device time.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
With the previous patch series, no opmode continues using the
command or handler_status (i.e. the return value from the RX)
so it can be removed now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In the mvm driver, neither the old command nor the return value
are used, so remove them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
After the previous patches, the command that's passed in nor the
return value are used any more, so can be removed.
While at it, make some functions static.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This makes the logging a little less useful, but as they're mostly
synchronous commands it won't matter much. It gets rid of the
dependency on the input command, which this is the only user of.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This driver currently has some very confusing ADD_STA response handling
that runs asynchronously in the background for all of the commands, but
is only really necessary for synchronous ones (the really asynchronous
ones can only be done for already existing stations), and for the sync
ones it actually waits for the RX handler to return a status code.
Rework this to keep the debug printing in the handler, but do the code
that's supposed to have an effect only for sync commands in the command
sending function.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The current key offset assignment algorithm always uses the lowest
unused key offset, which will potentially lead to issues when the
firmware will change to take the key material for TX from the key
table rather than from the TX command.
In order to avoid those issues (and avoid forgetting about them)
change the key offset allocation algorithm now to avoid reusing key
offsets quickly.
The new algorithm always picks as the next offset the least recently
freed offset, i.e. the offset that has been unused for the longest
amount of time. This is implemented by having a generation counter
for each key offset that is incremented every time a key is deleted,
except for the one that's deleted, which is reset to zero. Thus the
highest counter is the key that's been unused longest.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
During NIC initialization shared HW is reset and this disables the
scheduler. Some HW platforms do not activate the scheduler after it.
Consequently all HCMD sent by the driver stay at the queues which cause
to queue stuck.
Set the scheduler to work on auto active mode so it would be activated upon
change over one of the queues' write pointer.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The driver code allows for the disabling of MSI interrupts; however the
module_parm line was missed and the option fails to show with modinfo.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [3.15+]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mwifiex:
* add TX DATA Pause support
* add multichannel and TDLS channel switch support
ath10k:
* enable VHT for IBSS
* initial work to support qca99x0 and the corresponding 10.4 firmware branch
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJVu222AAoJEG4XJFUm622biQIH/1A5WVvXw1WbxbnKh3xJmLSZ
OkuSORBl0rbzf0CTtxDax59JqjZaCUZ2MdehKiCFQsv7DKuYk3JnkkvIhSkuTcpX
k4x5CbTIY0MuERtvtsoH+A4hi571jqYprtECRDCZiyDkhNyEnKpKA+ImPXa8HMeQ
iXny9IsH//jtsgcorM2bNcV6QmeUjUozU1jbcRk1pOLd6755ntmI4dRgR0vEpolt
UUEjPEStiaxovXF+dIpEaaANpTggspjku+lFJ1mH6IIyCZMLsnQ3+V/mlFxnPKAA
xFneaOkDYdQYyBAjG7yrPaWWg705Oraamfl2W5a665cOqbfAsUZ+9H0AbHOzSYI=
=99A8
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2015-07-31' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
Major changes:
mwifiex:
* add TX DATA Pause support
* add multichannel and TDLS channel switch support
ath10k:
* enable VHT for IBSS
* initial work to support qca99x0 and the corresponding 10.4 firmware branch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 6301566e0b. Oleksij Rempel
noticed that the randomness doesn't look to be good enough and Stephan Mueller
commented:
"I would say that the discussed RNG does not seem fit for hooking it up with the
hwrandom framework."
http://lkml.kernel.org/g/3945775.m5HblJPgiO@tauon.atsec.com
So let's the revert the patch until we are sure that we can trust this random
generator.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In commit 33511b157b ("rtlwifi: add support to
send beacon frame"), the mechanism for sending beacons was established. That
patch works correctly for rtl8192cu, but there is a possibility of getting
the following warnings in the PCI drivers:
WARNING: CPU: 1 PID: 2439 at net/mac80211/driver-ops.h:12
ieee80211_bss_info_change_notify+0x179/0x1d0 [mac80211]()
wlp5s0: Failed check-sdata-in-driver check, flags: 0x0
The warning is followed by a NULL pointer dereference as follows:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000006
IP: [<ffffffffc073998e>] rtl_get_tcb_desc+0x5e/0x760 [rtlwifi]
This problem was reported at http://thread.gmane.org/gmane.linux.kernel.wireless.general/138645,
but no solution was found at that time.
The problem was also reported at https://bugzilla.kernel.org/show_bug.cgi?id=9744
and this solution was developed and tested there.
The USB driver works with a NULL final argument in the adapter_tx() callback;
however, the PCI drivers need a struct rtl_tcb_desc in that position.
Fixes: 33511b157b ("rtlwifi: add support to send beacon frame.")
Signed-off-by: Luis Felipe Dominguez Vega <lfdominguez@nauta.cu>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [3.19+]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On the 2GHz and and on the 5GHZ band only the extpa_gain setting from
the 5GHz band was checked. this patch makes it check the property from
the correct band.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes commit eae79b4f3e ("rsi: fix memory leak in rsi_load_ta_instructions()")
which stopped the driver from functioning.
Firmware data has been allocated using vmalloc(), resulting in memory
that cannot be used for DMA. Hence the firmware was first copied to a
buffer allocated with kmalloc() in the original code. This patch reverts
the commit and only calls "kfree()" to release the buffer after sending
the data. This fixes the memory leak without breaking the driver.
Add a comment to the kmemdup() calls to explain why this is done, and abort
if memory allocation fails.
Tested on a Topic Miami-Florida board which contains the rsi SDIO chip.
Also added the same kfree() call to the USB glue driver. This was not
tested on actual hardware though, as I only have the SDIO version.
Fixes: eae79b4f3e ("rsi: fix memory leak in rsi_load_ta_instructions()")
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Cc: stable@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
noisy false alarms.
* a fix for the NIC prepare flow that prevented the driver
from being able to access the device on certain systems.
* a fix for the scan prority handling which allows the
regular scan to run even if a scheduled scan is already
running.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gMW5
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-for-kalle-2015-07-30' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
* a fix for the stuck TFD queue mechanism - it was producing
noisy false alarms.
* a fix for the NIC prepare flow that prevented the driver
from being able to access the device on certain systems.
* a fix for the scan prority handling which allows the
regular scan to run even if a scheduled scan is already
running.
The stuck queue detection mechanism allows to detect queues
that are stuck. For sleeping clients, a queue may rightfully
be stuck: if a poor client implementation stays asleep for
more than 10s, then we don't want to trigger recovery flows
because of that client.
In order to cope with this, I added a mechanism that
monitors the state of the client: when a client goes to
sleep, the timer of his queues is frozen. When he wakes up,
the timer is reset to the right value so that if a client
was awake for more than 10s and the queues are stuck, only
then, the recovery flow will kick in.
This is valid only on non-shared queues: A-MPDU queues.
There was a bug in case we Tx to a sleeping client that has
an empty A-MPDU queue: the timer was armed to now + 10s.
This is bad, but pretty harmless.
The problem is that when the client wakes up, the timer is
modified to be now + remainder. But remainder is 0 since the
queue was empty when that client went to sleep...
Fix this by checking the state of the client before playing
with the timer when we add a packet to an empty queue.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Initial QCA99X0 support has a known issue with TCP Tx throughput.
All other path such as UDP Tx/Rx and TCP Rx meet their expectation
(> 900Mbps), but TCP Tx marked as low as 5Mbps when single pair is
used on iperf.
The root cause is turned out because TSO flag is not initialized
properly so that firmware configures TSO in wrong way.
TSO flags in msdu extension descriptor is required to be reset
to indicate firmware there is no TSO is enabled, otherwise it
could act as TSO is enabled which causes huge throughput drop.
In fact, it's enough by resetting TSO flags only to prevent the
unexpected behavior, but initializing whole msdu ext. descriptor
will help to clear uncertainty of firmware could bring on as it
constantly updated.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add vendor/device id of QCA99X0 V2.0 to pci id table and
QCA99X0_HW_2_0_CHIP_ID_REV to ath10k_pci_supp_chips[] for
QCA99X0 to get detected by the driver.
kvalo: now QCA99X0 family of chipsets is supported by ath10k.
Tested client, AP and monitor mode with QCA9990.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When max client was set to 512 in qca99x0, there was host memory
alloc failure during wmi service ready event handling. This issue
got resolved now, increasing max client limit from 256 to 512.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Host memory required for firmware is allocated while handling
wmi service ready event. Right now, wmi service ready is handled
in tasklet context and it calls dma_alloc_coherent() with atomic
flag (GFP_ATOMIC) to allocate memory in host needed for firmware.
The problem is, dma_alloc_coherent() with GFP_ATOMIC fails in
the platform (at least in AP platform) where it has less atomic
pool memory (< 2mb). QCA99X0 requires around 2 MB of host memory
for one card, having additional QCA99X0 card in the same platform
will require similarly amount of memory. So, it's not guaranteed that
all the platform will have enough atomic memory pool.
Fix this issue, by handling wmi service ready event in workqueue
context and calling dma_alloc_coherent() with GFP_KERNEL. mac80211 work
queue will not be ready at the time of handling wmi service ready.
So, it can't be used to handle wmi service ready. Also, register work
gets scheduled during insmod in existing ath10k_wq and waits for
wmi service ready to completed. Both workqueue can't be used for
this purpose. New auxiliary workqueue is added to handle wmi service
ready.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch enables raw Rx/Tx encap mode to support software based
crypto engine. This patch introduces a new module param 'cryptmode'.
cryptmode:
0: Use hardware crypto engine globally with native Wi-Fi mode TX/RX
encapsulation to the firmware. This is the default mode.
1: Use sofware crypto engine globally with raw mode TX/RX
encapsulation to the firmware.
Known limitation:
A-MSDU must be disabled for RAW Tx encap mode to perform well when
heavy traffic is applied.
Testing: (by Michal Kazior <michal.kazior@tieto.com>)
a) Performance Testing
cryptmode=1
ap=qca988x sta=killer1525
killer1525 -> qca988x 194.496 mbps [tcp1 ip4]
killer1525 -> qca988x 238.309 mbps [tcp5 ip4]
killer1525 -> qca988x 266.958 mbps [udp1 ip4]
killer1525 -> qca988x 477.468 mbps [udp5 ip4]
qca988x -> killer1525 301.378 mbps [tcp1 ip4]
qca988x -> killer1525 297.949 mbps [tcp5 ip4]
qca988x -> killer1525 331.351 mbps [udp1 ip4]
qca988x -> killer1525 371.528 mbps [udp5 ip4]
ap=killer1525 sta=qca988x
qca988x -> killer1525 331.447 mbps [tcp1 ip4]
qca988x -> killer1525 328.783 mbps [tcp5 ip4]
qca988x -> killer1525 375.309 mbps [udp1 ip4]
qca988x -> killer1525 403.379 mbps [udp5 ip4]
killer1525 -> qca988x 203.689 mbps [tcp1 ip4]
killer1525 -> qca988x 222.339 mbps [tcp5 ip4]
killer1525 -> qca988x 264.199 mbps [udp1 ip4]
killer1525 -> qca988x 479.371 mbps [udp5 ip4]
Note:
- only open network tested for RAW vs nwifi performance comparison
- killer1525 (qca6174 hw2.2) is 2x2 device (hence max 866mbps)
- used iperf
- OTA, devices a few cm apart from each other, no shielding
- tcpX/udpX, X - means number of threads used
Overview:
- relative Tx performance drop is seen but is within reasonable and
expected threshold (A-MSDU must be disabled with RAW Tx)
b) Connectivity Testing
cryptmode=1
ap=iwl6205 sta1=qca988x crypto=open topology-1ap1sta OK
ap=iwl6205 sta1=qca988x crypto=wep1 topology-1ap1sta OK
ap=iwl6205 sta1=qca988x crypto=wpa topology-1ap1sta OK
ap=iwl6205 sta1=qca988x crypto=wpa-ccmp topology-1ap1sta OK
ap=qca988x sta1=iwl6205 crypto=open topology-1ap1sta OK
ap=qca988x sta1=iwl6205 crypto=wep1 topology-1ap1sta OK
ap=qca988x sta1=iwl6205 crypto=wpa topology-1ap1sta OK
ap=qca988x sta1=iwl6205 crypto=wpa-ccmp topology-1ap1sta OK
ap=iwl6205 sta1=qca988x crypto=open topology-1ap1sta2br OK
ap=iwl6205 sta1=qca988x crypto=wep1 topology-1ap1sta2br OK
ap=iwl6205 sta1=qca988x crypto=wpa topology-1ap1sta2br OK
ap=iwl6205 sta1=qca988x crypto=wpa-ccmp topology-1ap1sta2br OK
ap=qca988x sta1=iwl6205 crypto=open topology-1ap1sta2br OK
ap=qca988x sta1=iwl6205 crypto=wep1 topology-1ap1sta2br OK
ap=qca988x sta1=iwl6205 crypto=wpa topology-1ap1sta2br OK
ap=qca988x sta1=iwl6205 crypto=wpa-ccmp topology-1ap1sta2br OK
ap=iwl6205 sta1=qca988x crypto=open topology-1ap1sta2br1vlan OK
ap=iwl6205 sta1=qca988x crypto=wep1 topology-1ap1sta2br1vlan OK
ap=iwl6205 sta1=qca988x crypto=wpa topology-1ap1sta2br1vlan OK
ap=iwl6205 sta1=qca988x crypto=wpa-ccmp topology-1ap1sta2br1vlan OK
ap=qca988x sta1=iwl6205 crypto=open topology-1ap1sta2br1vlan OK
ap=qca988x sta1=iwl6205 crypto=wep1 topology-1ap1sta2br1vlan OK
ap=qca988x sta1=iwl6205 crypto=wpa topology-1ap1sta2br1vlan OK
ap=qca988x sta1=iwl6205 crypto=wpa-ccmp topology-1ap1sta2br1vlan OK
Note:
- each test takes all possible endpoint pairs and pings
- each pair-ping flushes arp table
- ip6 is used
c) Testbed Topology:
1ap1sta:
[ap] ---- [sta]
endpoints: ap, sta
1ap1sta2br:
[veth0] [ap] ---- [sta] [veth2]
| | | |
[veth1] | \ [veth3]
\ / \ /
[br0] [br1]
endpoints: veth0, veth2, br0, br1
note: STA works in 4addr mode, AP has wds_sta=1
1ap1sta2br1vlan:
[veth0] [ap] ---- [sta] [veth2]
| | | |
[veth1] | \ [veth3]
\ / \ /
[br0] [br1]
| |
[vlan0_id2] [vlan1_id2]
endpoints: vlan0_id2, vlan1_id2
note: STA works in 4addr mode, AP has wds_sta=1
Credits:
Thanks to Michal Kazior <michal.kazior@tieto.com> who helped find the
amsdu issue, contributed a workaround (already squashed into this
patch), and contributed the throughput and connectivity tests results.
Signed-off-by: David Liu <cfliu.tw@gmail.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Tested-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
During tx completion, tx_lock is held for longer than required, preventing
efficient refill of htt->pending_tx. Refactor the code so that only MSDU
related operations are protected by the lock.
Improves downstream performance on a dual-core ARM Freescale LS1024A
(f.k.a. Mindspeed Comcerto 2000) AP with a 3x3 client from 495 to 580 Mbps.
Other CPU bound multicore systems may also benefit.
Signed-off-by: Denton Gentry <dgentry@google.com>
Signed-off-by: Avery Pennarun <apenwarr@google.com>
[mfaltesek@google.com: removed conflicting code for tracking msdu_ids.]
Signed-off-by: Marty Faltesek <mfaltesek@google.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When using DFS channels on Ath10k, kernel log has repeated warning message
'failed to process fft: -22' typically under medium/heavy traffic.
This patch switches the warnings to driver debug (WMI events) mode only
thus reducing log file noise.
DFS and spectral scan share underlying HW mechanisms and enabling one
(DFS) enables the other (spectral scan) as far as event reporting from
firmware to driver is concerned. Spectral scan events take no part in
processing of DFS radar pulses which are delivered as distinct events,
so the fft (spectral event) warning is harmless and DFS interference
detection/protection still occurs.
Symptoms seen & fix tested in both debug & non-debug modes on TP-Link
Archer C7 v2 platform.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This fixes two misspellings of "distribution" in a comment.
Signed-off-by: Nik Nyby <nikolas@gnu.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The code checks the total number of iterations to differentiate
between regular scan and scheduled scan. However, regular scan has
a total of one iteration, not zero. As a result, regular scan will
have lower priority than it should have, and in case scheduled
scan is already running when regular scan is requested, regular scan
will be delayed until scheduled scan is aborted.
Fix that by checking for total iterations number of one as an
identifier for regular scan.
Fixes: 133c8259f8 ("iwlwifi: mvm: rename generic_scan_cmd functions to dwell")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When the card is not owned by the PCIe bus, we need to
acquire ownership first. This flow is implemented in
iwl_pcie_prepare_card_hw. Because of a hardware bug, we
need to disable link power management before we can
request ownership otherwise the other user of the device
won't get notified that we are requesting the device which
will prevent us from acquire ownership.
Same holds for the down flow where we need to make sure
that any other potential user is notified that the driver
is going down.
CC: <stable@vger.kernel.org> [4.1]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
HTT_H2T_MSG_TYPE_MGMT_TX msg in 10.4 firmware carries additional
4 byte in htt_mgmt_tx_desc where it tells to firmware that at what
rate mgmt frame has to go out in the air. It's an optional parameter,
setting this field to zero will force firmware to choose auto rate
and send the frame out.
Those 4 byte info is missed out in the current code and 10.4 firmware
ended up reading some junk in those 4 byte and sometime malfunctioning.
Fix it by adding 4 byte in struct htt_mgmt_tx_desc. Non 10.4 firmware
will not process those four byte. So, adding 4 byte at the end of
struct htt_mgmt_tx_desc will not create any impact on other chipset.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The patch adds support to offload TCP/UDP checksum
calculations for QCA99x0.
Signed-off-by: Manikanta Pubbisetty <c_mpubbi@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
chandef is initialized with NULL and on the very next line, we are using it to
get channel, which is not correct. Channel should be initialized after
obtaining chandef.
Found by cppcheck:
ath/ath10k/mac.c:839]: (error) Possible null pointer dereference: chandef
Signed-off-by: Maninder Singh <maninder1.s@samsung.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA99X0 chip has an extra 4 bytes in rx_msdu_start,
20 bytes in rx_msdu_end and 20 bytes in rx_ppdu_end structure
which are used in htt_rx_desc and HTT Rx ring offset setup.
This is necessary for correct Rx for QCA99X0 or Rx descriptors
will be overwritten and corrupted.
With this patch QCA988X and QCA6174 will have extra 44 bytes
padding in Rx descriptor layout which is harmless.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
rx_ppdu_end_common structure is valid for both of qca998x and
qca6174, but not for qca99x0 since it has new additional members.
Hence update the common structure to cover qca99x0 as well.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since QCA99X0 uses fragmentation descriptor differently from
other ones on tx path, we need to handle it separately.
QCA99X0 is using 48 bits for address and 16 bits for length
out of 2 dword and each values have to be programmed by frag
desc base addr + msdu id, so that hardware can retrieve
corresponding frag data.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is observed that during cold reset pcie access right
after a write operation to SOC_GLOBAL_RESET_ADDRESS causes
Data Bus Error and system hard lockup. The reason
for bus error is that pcie needs some time to get
back to stable state for any transaction during cold reset. Add
delay of 20 msecs after write of SOC_GLOBAL_RESET_ADDRESS
to fix this issue. This patch is tested on QCA988X. This is
also tested on QCA99X0 which is WIP.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
While changing interface type from p2p client or p2p go to
station, we should update counters for p2p interface and
station interface. Also calling mwifiex_cfg80211_deinit_p2p
method instead of mwifiex_cfg80211_init_p2p_client method to
deinit p2p interface.
Signed-off-by: Aniket Nagarnaik <aniketn@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
0xfe is basically a magic number used to ask firmware match
provided string in a SSID. In this case, firmware will
return scan results containing"DIRECT-" string.
Signed-off-by: Aniket Nagarnaik <aniketn@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We are setting BSS mode as ANY so that firmware will provide
all types of scan entries.
Signed-off-by: Aniket Nagarnaik <aniketn@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is no need to use hex_dump_to_buffer() in the cases like this:
hexdump_to_buffer(buf, len, 16, 1, outbuf, outlen, false); /* len <= 16 */
sprintf("%s\n", outbuf);
since it maybe easily converted to simple:
sprintf("%*ph\n", len, buf);
Note: it seems in the case the output is groupped by 2 bytes and looks like a
typo. Thus, patch changes that to plain byte stream.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
update the rssi reading on rx_status
to read both RSSI level (7 bits) and
antenna diversity (msb)
Signed-off-by: Guy Mishol <guym@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We measured the FFT-based entropy in 3 ways, Shannon entropy,
collision entropy, and directly measured min-entropy. Just to
be conservative, we recommend the estimated min-Entropy to be
10 bits per 16-bit value.
Analysis was done by Jacobson,David(djacobso@qti.qualcomm.com).
Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Broadcom's firmware requires every BSS to use MAC address with unique
last few bits. The amount of bits may depend on a particular firmware,
it was verified to be 2 for BCM43602 one.
If this condition won't be fulfilled firmware will reject such MAC:
brcmfmac: _brcmf_set_mac_address: Setting cur_etheraddr failed, -52
We don't want to simply set addr_mask as it would also disallow using
locally administrated bit. Instead let's build a list of addresses
manually enabling 0x2 bit for extra interfaces.
Signed-off-by: Rafa? Mi?ecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
While compiling ath9k with some extra flags I've
found that:
ath9k/xmit.c +2473 ## 16: warning: restricted __le16 degrades to integer
ath9k/xmit.c +2474 ## 36: warning: invalid assignment: &=
ath9k/xmit.c +2474 ## 36: left side has type restricted __le16
ath9k/xmit.c +2474 ## 36: right side has type int
There's no way for frame ftype/stype to be
mistreated as the offending 'moredata' flag when
considering cab queue.
This could've however theoretically led sometimes
to increased power consumption on connected
stations as they would keep their Rx active
waiting for frames that would never come.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Replace a kmalloc+strcpy by an equivalent kstrdup in order to improve
readability.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In routine _rtl8821ae_set_media_status(), an incorrect mask results in a test
for AP status to always be false. Similar bugs were fixed in rtl8192cu and
rtl8192de, but this instance was missed at that time.
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [3.18+]
Cc: David Binderman <dcb314@hotmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch fixes following issues in p2p code paths.
1) bss role, bss type and connection type was not set correctly
for p2p GO and p2p client at couple of places.
2) Driver appends a proprietary header to management frames
which will be parsed by our firmware. Later while informing
TX status to cfg80211, modified frame buffer was passed to
cfg80211_mgmt_tx_status() instead of original one.
Signed-off-by: Aniket Nagarnaik <aniketn@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A long time ago, ath9k had issues during reset where the DMA engine
would stay active and could potentially corrupt memory.
To debug those issues, the driver would print warnings whenever they
occur.
Nowadays, these issues are gone and the primary cause of these messages
is if the MAC is stuck during reset or busy processing a long
transmission. This is fairly harmless, yet these messages continue to
worry users.
To reduce the number of bogus bug reports, turn these messages into
debug messages and count their occurence in the "reset" debugfs file.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When wlcore_probe_of failed, return the correct error code instead of ENOMEM
Signed-off-by: Raphaël Poggi <poggi.raph@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
