There are a few different tx paths depending on
firmware and frame itself.
Creating a uniform decision will make it possible
to switch between different txmode easier, both
for testing and for future features as well.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If htt.freq isn't cleared and contains garbage fw
may discard tx packets. Prevent this from
happening by clearing htt.freq properly.
Possible manifestation of the problem could be not
being able to send auth request/response frames on
firmware with HTT >= 3.4 (when freq param was
introduced), e.g. on qca6174.
Fixes: 8d6d362436 ("ath10k: fix offchan reliability")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit 8348db2984 ("ath10k: add ATH10K_FW_IE_HTT_OP_VERSION") broke QCA6174
receive side as the HTT ids from ATH10K_FW_HTT_OP_VERSION_MAIN don't have
HTT_TLV_T2H_MSG_TYPE_RX_IN_ORD_PADDR_IND set. Fix this by adding a backwards
compatibility code which sets HTT op version if it's not set by the firmware
image.
Fixes: 8348db2984 ("ath10k: add ATH10K_FW_IE_HTT_OP_VERSION")
Reported-by: Michal Kazior <michal.kazior@tieto.com>
Tested-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add new ID for ASUS N10 WiFi dongle.
Signed-off-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: John W. Linville <linville@tuxdriver.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
USB ID 2001:330d is used for a D-Link DWA-131.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This will expose in /sys whether the ifname of a device is set by
userspace or generated by the kernel. The latter kind (wlanX, etc)
is not deterministic, so userspace needs to rename these devices
to names that are guaranteed to stay the same between reboots. The
former, however should never be renamed, so userspace needs to be
able to reliably tell the difference.
Similar functionality was introduced for the rtnetlink core in
commit 5517750f05 ("net: rtnetlink - make create_link take name_assign_type")
Signed-off-by: Tom Gundersen <teg@jklm.no>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Brett Rudley <brudley@broadcom.com>
Cc: Arend van Spriel <arend@broadcom.com>
Cc: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Cc: Hante Meuleman <meuleman@broadcom.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
[reformat changelog to fit 72 cols]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds recovery mechanism for SDIO RX during SKB allocation
failures.
For allocation failures during multiport aggregation, we skip and drop RX
packets.
For single port read case, we will use preallocated card->mpa_rx.buf to
complete cmd53 read.
Now we terminate SDIO operations only upon cmd53 failures.
CC: James Cameron <quozl@laptop.org>
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Cancel all pending commands including scan commands and stop CAC
during cfg80211 suspend handler.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
"adapter->sleep_cfm" is always non-NULL at this point. Static checkers
complain that we already dereference it at the start of the function
when we do:
skb_put(adapter->sleep_cfm, sizeof(struct mwifiex_opt_sleep_confirm));
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
SDIO reset was not happening properly on mwifiex as cancel_work_sync
in mwifiex_sdio_remove used to kill the calling work function itself.
Due to this, the interface was not getting removed and card was not
getting added again. Reset work function has been made independent
of adapter variable and cancel_work_sync has been moved to cleanup
function.
Signed-off-by: Maithili Hinge <maithili@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
replace REG_WRITE to REG_RMW and place every thing in one
RMW buffer.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
it is possible to reduce time needed for this function
by rplacing REG_WRITE with REG_RMW (plus dummy 0) and putt all commands
in same buffer.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
it will reduce exution time from 14ms to 2ms on ar9271
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
use REG_RMW in ath9k_hw_analog_shift_rmw.
It will double execution speed on usb bus.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
insted of reading each register separatly
and waste 4ms on each operation, we can
use one shot read.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
REG_READ generate most overhead on usb bus. It send and read micro packages
and reduce usb bandwidth. To reduce this overhead we should read in batches.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This function uses mixed styles for register names/numbers which
is make harder reading and optimisation.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since usb bus add extra delay on each request, a command
with read + write requests is too expensive. We can dramtically
reduce usb load by moving this command to firmware.
In my tests, this patch will reduce channel scan time
for about 5-10 seconds.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
I changed REG_CR+2 and (MSR) to MSR because MSR is defined as (REG_CR + 2).
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Seems H/W report correctly firmware Autorun value only at initialization
stage. When we close interface and open it again, Autorun value is 0 and
we try to load firmware what kills the device. To fix clear
REQUIRE_FIRMWARE firmware flag, to do not load firmware again, once we
discover Autorun mode.
Reported-and-tested-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We will be able to add more events, such as MLME events and
others. The low level driver may be interested in knowing
about these events to dump firmware data upon failures, or
to change parameters in case connection attempts fail etc...
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Patch "ath10k: introduce basic tdls functionality" depends on this mac80211
patch:
c23e31cf7b mac80211: initialize rate control earlier for tdls station
was loaded.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wIgU
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-for-kalle-2015-03-30' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
* fix a memory leak: we leaked memory each time the module
was loaded.
Firmware 10.2.4.48-3 now supports management frames over HTT feature and has
ATH10K_FW_FEATURE_HAS_WMI_MGMT_TX. But as 10.2.4 branch has conflicting HTT ids
patch "ath10k: add ATH10K_FW_IE_HTT_OP_VERSION" is needed to fix the issue.
Older ath10k versions don't have support that support and to maintain backwards
compatibility we need bump up the FW API to 5 not break older versions.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Target to host HTT messages are conflicting between 10.x and other
firmware revisions. By maintaining separate HTT T2H tables for each
firmware revisions (main, 10x and tlv) similar to WMI abstraction,
solves the conflicts. Add ATH10K_FW_IE_HTT_OP_VERSION so that the firmware can
advertise the HTT interface to ath10k.
This fix is needed to get management frames over HTT (ie.
ATH10K_FW_FEATURE_HAS_WMI_MGMT_TX disabled) working with 10.2.4.48-2 firmware.
Otherwise there will be unknown htt events and nothing works:
[30087.438343] ath10k_pci 0000:02:00.0: htt event (19) not handled
[30087.448691] ath10k_pci 0000:02:00.0: htt event (19) not handled
[30149.032974] ath10k_pci 0000:02:00.0: htt event (19) not handled
If the firmware does not have ATH10K_FW_IE_HTT_OP_VERSION use the main HTT
interface. That way old firmware images will still work.
Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add support for WOW disconnect and magic-packet.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add WMI support for WOW like enable,
wakeup events and host wakeup indication.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In the reset flow, the driver cancels ongoing scan and sends scan
complete notification to mac80211. However it does not clean its UID.
Add cleaning scan UID for the ongoing scan. Loop over all other UIDs
to make sure there's nothing left there and warn if any is found.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
There is a strong relationship between the NVM version and
the hardware step. Enforce that in the driver in case the
default NVM on the platform is the wrong one.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The semaphore may not be accessible. Fix the debug prints
accordingly.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Sometimes we will want to configure the timeouts for the
Tx queues based on the vif type. Allow to do that using the
trigger mechanism.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
There is no need to implement the enable_scan_iteration_notif handling
explicitly and there's no reason not to export the current value. So
use debugfs_create_bool() instead.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add support for delaying the start of a scheduled scan (or a WoWLAN
net-detect scan).
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
ref_count is currently initialized on start_fw(). This causes
some issues in restart flow, as currently active references
(e.g. unclaimed command) will get cleared, resulting in
invalid reference accounting.
Move the ref_count initialization to the configure() trans op,
so it won't be re-initialized on restart.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In nic restart flow we inform mac80211 that scan was aborted, but it was
based only on scan_status which is not set by UMAC scan. Fix that.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The AP_START d0i3 reference was never removed if the AP started correctly.
This has the unpleasant side-effect of preventing D0i3 on Android if the
WiFi hotspot was ever started on the device.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
