We currently get the output connected to LVDS by looking for a phandle
called 'qcom,lvds-panel' under the mdp DT node.
Use the more standard of_graph approach to create an lvds output port,
and retrieve the panel node from the port's endpoint data.
v3
- Fix return value checks of of_graph_* calls.
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The maximum output width of one pipeline depends on the LayerMixer's
capability. It may be different on each target. Also, MDP5 doesn't
have vertical limitation in one frame, as long as the pixel clock
can be supported.
This change obtains the maximum LM resolution from configuration
table and treat it as the whole pipe's limitation for MDP5. The size
limit on MDP4 is not changed.
Signed-off-by: Hai Li <hali@codeaurora.org>
MDP FLUSH registers could indicate if the previous flush updates
has taken effect at vsync boundary. Making use of this H/W feature
can catch the vsync that happened between CRTC atomic_flush and
*_wait_for_vblanks, to avoid unnecessary wait.
This change allows kms CRTCs to use their own *_wait_for_commit_done
functions to wait for FLUSH register cleared at vsync, before commit
completion.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Using fb modifier flag, support NV12MT format in MDP4.
v2:
- rework the modifier's description [Daniel Vetter's comment]
- drop .set_mode_config() callback [Rob Clark's comment]
v3:
- change VENDOR's name and restrict usage to NV12 [pointed by Daniel]
Signed-off-by: Rob Clark <robdclark@gmail.com>
As a result of atomic DPMS support, the various prepare/commit hooks get
called in a way that msm dislikes. We were expecting prepare/commit to
bracket a modeset, which is no longer the case. This was needed to hold
various extra clk's (such as interface clks) on while we are touching
registers, and in the case of mdp4 holding vblank enabled.
The most straightforward way to deal with this, since we already have
our own atomic_commit(), is to just handle prepare/commit internally to
the driver (with some additional vfuncs for mdp4 vs mdp5), and switch
everything over to instead use the new enable/disable hooks. It doesn't
really change too much, despite the code motion. What used to be in the
encoder/crtc dpms() fxns is split out into enable/disable.
We should be able to drop our own enable-state tracking, as the atomic
helpers should do this for us. But keeping that for the short term for
extra debugging as atomic stablizes.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Split up hdmi_init() into hdmi_init() (done at hdmi sub-device
bind/probe time) and hdmi_modeset_init() done from master driver's
modeset_init().
Anything that can fail due to dependencies on other drivers which
may be missing or not probed yet should go in hdmi_init(), so that
devm error/cleanup paths work properly.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Fixes a potential error, spotted by Felipe with randconfig:
-----
drivers/gpu/drm/msm/mdp/mdp4/mdp4_kms.c: In function ‘mdp4_kms_init’:
drivers/gpu/drm/msm/mdp/mdp4/mdp4_kms.c:384:2: error: implicit declaration \
of function ‘devm_regulator_get_exclusive’ [-Werror=implicit-function-declaration]
mdp4_kms->vdd = devm_regulator_get_exclusive(&pdev->dev, "vdd");
^
drivers/gpu/drm/msm/mdp/mdp4/mdp4_kms.c:384:16: error: assignment makes \
pointer from integer without a cast [-Werror]
mdp4_kms->vdd = devm_regulator_get_exclusive(&pdev->dev, "vdd");
^
-----
Also add a brief comment explaining the use of _get_exclusive()
Reported-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
LVDS panel support uses the LCDC (parallel) encoder. Unlike with HDMI,
there is not a separate LVDS block, so no need to split things into a
bridge+connector. Nor is there is anything re-used with mdp5.
Note that there can be some regulators shared between HDMI and LVDS (in
particular, on apq8064, ext_3v3p), so we should not use the _exclusive()
variants of devm_regulator_get().
The drm_panel framework is used for panel-specific driver.
Signed-off-by: Rob Clark <robdclark@gmail.com>
In particular, blend_setup() should not overwrite the other crtc's mixer
settings. Also, the encoder needs to be able to specify the mixer-id
explicitly, since both LVDS and DTV use 'INTF_LVDC_DTV', so we cannot
guess the mixer-id from the interface.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Downstream kernel IOMMU had a non-standard way of dealing with multiple
devices and multiple ports/contexts. We don't need that on upstream
kernel, so rip out the crazy.
Note that we have to move the pinning of the ringbuffer to after the
IOMMU is attached. No idea how that managed to work properly on the
downstream kernel.
For now, I am leaving the IOMMU port name stuff in place, to simplify
things for folks trying to backport latest drm/msm to device kernels.
Once we no longer have to care about pre-DT kernels, we can drop this
and instead backport upstream IOMMU driver.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Downstream kernel holds this clk via a fake-parent relationship.
Upstream clock framework requires that we hold it explicitly.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Now that we (almost) have enough dependencies in place (MMCC, RPM, etc),
add necessary DT support so that we can use drm/msm on upstream kernel.
v2: update for review comments
v3: rebase on component helper changes
Signed-off-by: Rob Clark <robdclark@gmail.com>
The hw cursor is relatively adept at triggering underflows, which
manifest as a "blue flash" (since blue is configured as the underflow
color). Juggle a few things around to tighten up the timing for setting
cursor registers in DONE irq.
And most importantly, don't ever disable the hw cursor. Instead flip it
to a blank/empty cursor. This seems far more reliable, as even simply
clearing the cursor-enable bit (with no other updates in previous/
following frames) can in some cases cause underflow.
v1: original
v2: add missing locking spotted by Micah
Cc: Micah Richert <richert@braincorporation.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The HDMI block is basically the same between older SoC's with mdp4
display controller, and newer ones with mdp5.
So mostly this consists of better abstracting out the different sets of
regulators, clks, etc. In particular, for regulators and clks we can
split it up by what is needed for hot plug detect to work, and what is
needed to light up the display.
Also, 8x74 has a new phy.. a very simple one, but split out into a
different mmio space. And with mdp5, the irq is shared with mdp, so we
don't directly register our own irq handler.
Signed-off-by: Rob Clark <robdclark@gmail.com>
This can be shared between mdp4 and mdp5. Both use the same set of
parameters to describe the format to the hw.
Signed-off-by: Rob Clark <robdclark@gmail.com>
There are some little bits and pieces that mdp4 and mdp5 can share, so
move things around so that we can have both in a common parent
directory.
Signed-off-by: Rob Clark <robdclark@gmail.com>
2014-01-09 14:38:59 -05:00
Renamed from drivers/gpu/drm/msm/mdp4/mdp4_kms.c (Browse further)
