Setup the emc pins used by external memory devices and add
configuration for the devices found on the EA4357 devkit.
The EA4357 devkit has a NOR Flash attached to chip select 0
and a D-type flip-flop used for LEDs on chip select 2.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Enable USB0 on the EA4357 devkit and setup the required USB0
control pins.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
All devices in the LPC18xx/43xx familiy contain a ARM PL172
MultiPort Memory Controller (MPMC).
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
NXP LPC185x and LPC435x/70 devices contain a ARM PL111 lcd controller.
Signed-off-by: Joachim Eastwood <joachim.eastwood@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add the USB OTG phy under the CREG syscon node and attach it to
the USB0 EHCI controller.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
*) Fix compiler error when sun4i usb phy driver is built as module
*) Fix SATA Lockup issue in dra7 SoC
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=j6wu
-----END PGP SIGNATURE-----
Merge tag 'phy-for-4.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-linus
Kishon writes:
phy: for 4.2-rc6
*) Fix compiler error when sun4i usb phy driver is built as module
*) Fix SATA Lockup issue in dra7 SoC
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The PMU device contains an interrupt controller, power control and
resets. The interrupt controller is a little sub-standard in that
there is no race free way to clear down pending interrupts, so we try
to avoid problems by reducing the window as much as possible, and
clearing as infrequently as possible.
The interrupt support is implemented using an IRQ domain, and the
parent interrupt referenced in the standard DT way.
The power domains and reset support is closely related - there is a
defined sequence for powering down a domain which is tightly coupled
with asserting the reset. Hence, it makes sense to group these two
together, and in order to avoid any locking contention disrupting this
sequence, we avoid the use of syscon or regmap.
This patch adds the core PMU driver: power domains must be defined in
the DT file in order to make use of them. The reset controller can
be referenced in the standard way for reset controllers.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add the description of the GPU power domain to the PMU DT entry.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add the description of the video decoder power domain to the PMU DT
entry.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Now that we have a PMU driver, we can wire up the RTC interrupt in the
DT description for Dove.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add the PMU node, and move the child devices of the PMU node beneath
this new node, giving it a "simple-bus" so that the OF platform
device creator will create these child devices. No functional change
from this is expected.
The PMU provides multiple features, including an interrupt, reset,
power and isolation controller.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Merge "ARM: Interrupt cleanups and API change preparation" from Thomas
Gleixner:
The following patch series contains the following changes:
- Consolidation of chained interrupt handler setup/removal
- Switch to functions which avoid a redundant interrupt
descriptor lookup
- Preparation of interrupt flow handlers for the 'irq' argument
removal
* 'queue/irq/arm' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
ARM/orion/gpio: Prepare gpio_irq_handler for irq argument removal
ARM/pxa: Prepare balloon3_irq_handler for irq argument removal
ARM/pxa: Prepare *_irq_handler for irq argument removal
ARM/dove: Prepare pmu_irq_handler for irq argument removal
ARM/sa1111: Prepare sa1111_irq_handler for irq argument removal
ARM/locomo: Prepare locomo_handler for irq argument removal
ARM, irq: Use irq_desc_get_xxx() to avoid redundant lookup of irq_desc
ARM/LPC32xx: Use irq_set_handler_locked()
ARM/irq: Use access helper irq_data_get_affinity_mask()
ARM/locomo: Consolidate chained IRQ handler install/remove
ARM/orion: Consolidate chained IRQ handler install/remove
Signed-off-by: Olof Johansson <olof@lixom.net>
Nand controller often share some pins with sd/mmc controller on
atlas and prima series, nand node can be disabled if the pins are
used by sd/mmc controller.
Signed-off-by: Huayi Li <huayi.li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
this patch adds SDR(software digital raio) nodes and the DMA channels
for it.
Signed-off-by: Yonghui Zhang <yonghui.zhang@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
this patch adds lost PWM node, and also fixes the ranges of its
parent node.
Signed-off-by: Guo Zeng <guo.zeng@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
this patch adds lost G2D node, and also fixes the range of its
parent node.
Signed-off-by: Dongli Li <Kasin.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
this patch adds multimedia video codec node, and also fixes the
ranges of its parent node.
Signed-off-by: Xiaofeng Fei <xiaofeng.fei@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
spi framework can use alias name of spi device to retrieve the bus id,
so bus id will not be dynamical but statical and it will be easier for
test for a specified spi device with a fixed name like use spidev.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
this patch adds lost ethernet gmac node, and also fix the ranges of
its parent node.
Signed-off-by: Ye He <ye.he@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
this patch adds lost jpeg node, and also fix the ranges of its
parent node.
Signed-off-by: Lily.Li <Lily.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Add FEC MAC refrence clock init.
Add phy fixup init for i.MX6ul 14x14 evk board that installs KSZ8081 phy.
For the phy, there needs extra phy fixup for MII and RMII mode.
Signed-off-by: Fugang Duan <b38611@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add eMMC pinmux and mmc2 related bits. We keep the mmc2
controller disabled as it conflits with gpmc/NAND.
To enable emmc, simply set mmc2 controller node to "okay"
and set the gpmc node to "disabled" and change the
SelEMMCorNAND gpio-hog to output-high.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On this board either eMMC or NAND can work based on the level of
spi2_cs0.gpio0_23. Add a gpio-hog to enable configuration of this
pin in the device tree.
Move pinmux for spi2_cs0 (SEL_eMMCorNANDn) out of
NAND node into gpio0 so it is initialized with gpio0.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ldo1_reg in addition to being connected to the io lines is also
connected to the card detect line. On card removal, omap_hsmmc
driver does a regulator_disable causing card detect line to be
pulled down. This raises a card insertion interrupt and once the
MMC core detects there is no card inserted, it does a
regulator disable which again raises a card insertion interrupt.
This happens in a loop causing infinite MMC interrupts.
Fix it by making ldo1_reg as always_on.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ldo1_reg in addition to being connected to the io lines is also
connected to the card detect line. On card removal, omap_hsmmc
driver does a regulator_disable causing card detect line to be
pulled down. This raises a card insertion interrupt and once the
MMC core detects there is no card inserted, it does a
regulator disable which again raises a card insertion interrupt.
This happens in a loop causing infinite MMC interrupts.
Fix it by making ldo1_reg as always_on.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
pbias-supply is initialized in dra7.dtsi. Remove redundant initialization
of pbias-supply from MMC1 dt node in am57xx-beagle-x15.dts
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
SDMMC Card Detect can be used over default GPIO map.
Reported-by: Yan Liu <yan-liu@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
MMC1 supports SDR104 and MMC2 supports HS200 both of which requires
192MHz clock. Set the maximum operating clock frequency to 192 MHz.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a node for evm_3v3_sd using onboard pcf GPIO expander which feeds
on to mmc vdd.
Update mapping for vmmc-supply and vmmc_aux-supply.
evm_3v3_sd supplies to SD card vdd, and ldo1 to sdcard i/o lines.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a node for evm_3v3_sd using pcf which feeds on to mmc vdd.
Update mapping for vmmc-supply and vmmc_aux-supply.
evm_3v3_sd supplies to SD card vdd, and ldo1 to sdcard i/o lines.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the Wakeup M3 IPC device node for the wkup_m3_ipc driver on
AM4372 SoC. This node uses the IPC registers, part of the Control
Module, and is therefore added as a child of the scm node.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the Wakeup M3 IPC node for the wkup_m3_ipc driver on AM33xx SoCs.
This node uses the IPC registers, part of the Control Module, and is
therefore added as a child of the scm node.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
commit <d919501fef> ("ARM: dts: dra7: add minimal l4 bus
layout with control module support") moved pbias_regulator dt node
from being a child node of ocp to be the child node of
scm_conf. After this device for pbias_regulator is
not created.
Fix it by adding "simple-bus" compatible property to
scm_conf dt node.
Fixes: d919501fef ("ARM: dts: dra7: add minimal l4 bus
layout with control module support")
Cc: <stable@vger.kernel.org> # v4.1
Suggested-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
commit <ed8509eddd> ("ARM: dts: omap5: add minimal l4 bus
layout with control module support") moved pbias_regulator dt node
from being a child node of ocp to be the child node of
omap5_padconf_global. After this device for pbias_regulator is
not created.
Fix it by adding "simple-bus" compatible property to
omap5_padconf_global dt node.
Fixes: ed8509eddd ("ARM: dts: omap5: add minimal l4 bus
layout with control module support")
Cc: <stable@vger.kernel.org> # v4.1
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
commit <7415b0b4c6> ("ARM: dts: omap4: add minimal l4 bus layout
with control module support") moved pbias_regulator dt node
from being a child node of ocp to be the child node of
omap4_padconf_global. After this device for pbias_regulator
is not created.
Fix it by adding "simple-bus" compatible property to
omap4_padconf_global dt node.
Fixes: 7415b0b4c6 ("ARM: dts: omap4: add minimal l4 bus layout
with control module support")
Cc: <stable@vger.kernel.org> # v4.1
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
commit <72b10ac00e> ("ARM: dts: omap24xx: add minimal l4 bus
layout with control module support") moved pbias_regulator dt node
from being a child node of ocp to be the child node of
scm_conf. After this device for pbias_regulator is
not created.
Fix it by adding "simple-bus" compatible property to
scm_conf dt node.
Fixes: 72b10ac00e ("ARM: dts: omap24xx: add minimal l4 bus
layout with control module support")
Cc: <stable@vger.kernel.org> # v4.1
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This region contains CTRL_CORE_SMA_SW2..9 registers which
are not specific to any domain and can be reasonably
accessed via syscon driver.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need to add 4 bytes to include the last 32-bit register space.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These nodes are wrongly placed. They must come under the
scm node. Nobody uses them either so get rid of them.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 60f96b41f7 ("genirq: Add IRQCHIP_SKIP_SET_WAKE flag")
introduced a new flag to skip the irq_set_wake callback in the irqchip
core to avoid adding dummy irq_set_wake in the irqchip implementations.
This patch removes the dummy callback and sets the IRQCHIP_SKIP_SET_WAKE
flags.
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Improve dt support for orion5x
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlW7QLAACgkQCwYYjhRyO9VAqgCePD1+poLPe2yvEG0tlVO+Riq4
DLMAn3OoOO5UaISBXMBu/fPsd80UGDbH
=Yrv4
-----END PGP SIGNATURE-----
Merge tag 'mvebu-config-4.3-2' of git://git.infradead.org/linux-mvebu into next/defconfig
mvebu config changes for v4.3 (part #2)
Improve dt support for orion5x
* tag 'mvebu-config-4.3-2' of git://git.infradead.org/linux-mvebu:
ARM: defconfig: orion5x: add DT support
Signed-off-by: Olof Johansson <olof@lixom.net>
- Extend suspend to RAM support in order to add new mvebu SoC
- Add standby support for all Armada 3xx/XP SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlW7OiYACgkQCwYYjhRyO9WEIgCglOTwI09tYdDRxrW3gETI8RbM
cX8An3XYyaPavLOh58x9UMmiXwTBU5EM
=YmnC
-----END PGP SIGNATURE-----
Merge tag 'mvebu-soc-4.3-1' of git://git.infradead.org/linux-mvebu into next/soc
mvebu soc changes for v4.3 (part #1)
- Extend suspend to RAM support in order to add new mvebu SoC
- Add standby support for all Armada 3xx/XP SoCs
* tag 'mvebu-soc-4.3-1' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: Warn about the wake-up sources not taken into account in suspend
ARM: mvebu: Add standby support
ARM: mvebu: Use __init for the PM initialization functions
ARM: mvebu: prepare pm-board.c for the introduction of Armada 38x support
ARM: mvebu: prepare mvebu_pm_store_bootinfo() to support multiple SoCs
ARM: mvebu: do not check machine in mvebu_pm_init()
ARM: mvebu: prepare set_cpu_coherent() for future extension
Signed-off-by: Olof Johansson <olof@lixom.net>
- Fix earlyprintk, jump trampoline for SMP
- Update git tree location
- Setup PL310 aux (bit 22)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iEYEABECAAYFAlW7MWAACgkQykllyylKDCHkTACfT3Kzs+Cl7jc9A4kQ6dkbUqtC
E1MAn0g3yHcqGHgUtfyHu6lXtptJFbDn
=DuTZ
-----END PGP SIGNATURE-----
Merge tag 'zynq-soc-for-4.3' of https://github.com/Xilinx/linux-xlnx into next/soc
arm: Xilinx Zynq SoC patches for v4.2
- Fix earlyprintk, jump trampoline for SMP
- Update git tree location
- Setup PL310 aux (bit 22)
* tag 'zynq-soc-for-4.3' of https://github.com/Xilinx/linux-xlnx:
ARM: zynq: reserve space for jump target in secondary trampoline
clk: zynq: remove redundant $(CONFIG_ARCH_ZYNQ) in Makefile
MAINTAINERS: Update Zynq git tree location
ARM: zynq: Set bit 22 in PL310 AuxCtrl register (6395/1)
ARM: zynq: Fix earlyprintk in big endian mode
Signed-off-by: Olof Johansson <olof@lixom.net>
* Switch to use pinctrl compatible for GPIOs
* Add RPM regulators for MSM8960
* Add SPI Ethernet support on MSM8960 CDP
* Add SMEM support along with dependencies
* Add PM8921 support for GPIO and MPP
* Fix GSBI cell index
* Switch to use real regulators on APQ8064 w/ SDCC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=kyj6
-----END PGP SIGNATURE-----
Merge tag 'qcom-dt-for-4.3' of git://codeaurora.org/quic/kernel/agross-msm into next/dt
Qualcomm ARM Based Device Tree Updates for v4.3
* Switch to use pinctrl compatible for GPIOs
* Add RPM regulators for MSM8960
* Add SPI Ethernet support on MSM8960 CDP
* Add SMEM support along with dependencies
* Add PM8921 support for GPIO and MPP
* Fix GSBI cell index
* Switch to use real regulators on APQ8064 w/ SDCC
* tag 'qcom-dt-for-4.3' of git://codeaurora.org/quic/kernel/agross-msm:
ARM: dts: qs600: Add real regulators to sdcc
ARM: dts: ifc6410: add real regulators for sdcc nodes.
ARM: dts: apq8064: remove temporary fixed regulator for mmc
ARM: dts: apq8064: fix missing gsbi cell-index
ARM: dts: apq8064: Add DT support for GSBI6 and for UART pin mux
ARM: dts: apq8064: add pm8921 mpp support
ARM: dts: apq8064: Add pm8921 mfd and its gpio node
ARM: dts: msm8974: Add smem reservation and node
ARM: dts: msm8974: Add tcsr mutex node
ARM: dts: qcom: Add ks8851 node for wired ethernet
ARM: dts: qcom: Add MSM8960 CDP RPM regulators
ARM: dts: qcom: Add MSM8960 RPM and RPM regulator nodes
ARM: dts: qcom: Replace gpio node with pinctrl node
ARM: dts: qcom: Replace gpio node with pinctrl node
Signed-off-by: Olof Johansson <olof@lixom.net>
Add Atmel-isi and ov2640 driver in defconfig
Signed-off-by: Josh Wu <josh.wu@atmel.com>
[nicolas.ferre@atmel.com: make SOC_CAMERA_OV2640 selected as a module]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
