Change logic to check for various chip or core families to inline functions.
Checks for specific chips should be made against the state->id field now. This
is in preparation for chip/core specific code for setting up PLLs for the
CX2388[578] family of cores, that all run with different crystal frequencies.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add improved logic to detect the exact CX2388[578] A/V core that is being
probed. Also cleaned up detection and logging for CX2310[12], CX2583[67],
and CX2584[0123] cores and chips.
Also added code to identify a CX2388[578] A/V decoder core that is not
responding properly. Typical symptoms include registers 0x00-0xff
responding properly but all other registers returning the same value
(0x13 and 0x5 have been observed). This state will cause proper detection of
'885 vs. '887 vs. '888 to fail and the chip won't respond to get configured
properly anyway. I have no method of reseting the core to a working state at
this time; but I didn't try too hard to work one out either. The problem
likely only occurs in development. I suspect configuring the SYS PLL VCO to
oscillate too slowly (286.3 MHz?) before post divide may be the root cause,
when encountered.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This change adds a skeletal implementation of a v4l2_subdevice to provide
encapsulation and abstraction of the CX23888's integrated consumer infrared
controller. This change also instantiates the cx23888_ir subdev for the
HVR-1850 which has IR hardware physically wired up to a CX23888.
The cx23888_ir subdev code is being written with long-term objectives to:
1. port it to the cx25840 module for the CX2584x, CX2583x, CX23885, & CX231xx
IR controllers
2. possibly port it to the cx18 module for the CX23418 IR controller
3. have the IR subdevice accessed abstractly in the cx23885 module, so the
driver can ignore the difference between the CX23885 and CX23888.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This changes corrects the ioctl() operations for both the CX2388[578] analog
video and MPEG video device nodes to properly and consistently support
VIDIOC_G_CHIP_IDENT, VIDIOC_DBG_G_REGISTER and VIDIOC_DBG_S_REGISTER ioctl()s.
This caused some ioctl() support routines to be broken out into a separate
source file.
Now v4l2-dbg can be used to manipulate CX2388[578] and CX23417 registers
including the CX2388[57] functions handled by the cx25840 module.
This was done in anticipation of developing a new v4l2_subdev for the
integrated IR controller of the CX23888.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add identifiers for CX2388[578] chips, CX2310[012] chips, integrated
A/V decoders cores, integrated IR controller core, and the CX23417
MPEG encoder. The cx23885 module and cx25840 module will use these
identifiers in upcoming changes.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The board support has been validated by the user, so get rid of the warning
that shows up on board load.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Dmitri's patch for the Behold X7 didn't use the #define I had setup for
XC5000_RADIO_FM1, so cut over to using that instead of "1".
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for the digital side of the Behold X7
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make analog audio, dvb and the remote work on a Terratec Cinergy Hybrid
XS (em2882).
Note by djh: Thanks go out fo Andrej Suligoi for his contribution in providing
and testing pretty much the exact same patch as provided by Uros. Between
the two of them, they got all the core functionality working for the device.
Cc: Andrej Suligoi <suligoi@gmail.com>
Signed-off-by: Uroš Vampl <mobile.leecher@gmail.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Seems that the reference design used for the KWorld 2800d switched from the
em2860 to em2862, so we need to add the new USB id (and the i2c hash remains
so all we need is the default em2862 id.
Thanks to Ian Young for reporting the issue and testing the fix.
Cc: Ian Young <ian@duffrecords.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove hard-coded definition of the xc5000 FM radio input, making it a
parameter passed in when doing the attach call.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Set radio frequency only upon success.
Signed-off-by: David Ellingsworth <david@identd.dyndns.org>
Acked-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Preserve radio state during suspend/resume.
Signed-off-by: David Ellingsworth <david@identd.dyndns.org>
Acked-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ensure the radio is initialized to a consistent state.
Signed-off-by: David Ellingsworth <david@identd.dyndns.org>
Acked-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Looks like eeprom IR mode byte value 0x04 means there is remote
which should be polled. Patch enables polling also in case of 0x04.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Support for MSI DIGIVOX mini III remote.
Thanks to Aleksandr V. Piskunov <aleksandr.v.piskunov@gmail.com>
Thanks to Roman <lists@hasnoname.de>
Cc: Aleksandr V. Piskunov <aleksandr.v.piskunov@gmail.com>
Cc: Roman <lists@hasnoname.de>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add USB ID 1b80:c161 for KWorld PlusTV DVB-T PCI Pro Card (DVB-T PC160-T).
Thanks to Andrew Cruickshank <atcrank@gmail.com> for reporting this.
Cc: Andrew Cruickshank <atcrank@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Update the dib7000p:
The status is HAS_LOCK only if the demod is able to decode the TPS. Sometimes, there is a TPS data lock, even if the demod is not able to decode it (ex: no RF signal).
For the STK7770P: correct value for the charge pump
Signed-off-by: Olivier Grenie <olivier.grenie@dibcom.fr>
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
dib7000p/dib8000: added pid filtering
dib8000: the SNR is in 10th of dB (not in dB)
dib7000p and dib8000: added the pid filtering. This feature is enabled by module option (dvb-usb module).
Signed-off-by: Olivier Grenie <olivier.grenie@dibcom.fr>
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This IR uses NEC protocol. In order to use, dvb_usb_dib0700_ir_proto=0
should be used.
Cc: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently, dvb_usb_dib0700_ir_proto is supported only with firmwares
older than 1.2. Adds support for it also with the newer firmware.
This is needed in order to support PixelView SBTVD IR.
Cc: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Otherwise we have no guarantees that other processes won't start another
RPC call while we're resetting the session.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
in NFSv4.1 the seqid part of a stateid in CB_RECALL must be 0
Signed-off-by: Alexandros Batsakis <batsakis@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
the server can indicate a number of error conditions by setting the
appropriate bits in the SEQUENCE operation. The client re-establishes
state with the server when it receives one of those, with the action
depending on the specific case.
Signed-off-by: Alexandros Batsakis <batsakis@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The v4.1 client should take into account the desired rsize, wsize when
negotiating the max size in CREATE_SESSION. Accordingly, it should use
rsize, wsize that are smaller than the session negotiated values.
Signed-off-by: Alexandros Batsakis <batsakis@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
In v4.1 the client MUST/SHOULD use the EXCLUSIVE4_1 flag instead of
EXCLUSIVE4, and GUARDED when the server supports persistent sessions.
For now (and until we support suppattr_exclcreat), we don't send any
attributes with EXCLUSIVE4_1 relying in the subsequent SETATTR as in v4.0
Signed-off-by: Alexandros Batsakis <batsakis@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
For now the clients returns _all_ the delegations of the specificed type
it holds
Signed-off-by: Alexandros Batsakis <batsakis@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The NFSv4.1 spec-29 (18.36.3) says that the server MUST use an ONC RPC
(program) version number equal to 4 in callbacks sent to the client.
For now we allow both versions 1 and 4.
Signed-off-by: Alexandros Batsakis <batsakis@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
