`!' has a higher precedence than `&' so parentheses are required.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Keys: 'right arrow', 'up arrow' and 'select' were mapped
wrongly. This patch corrects them.
This patch also adds one missing key present in the board,
currently I added it as 'unknown' key, as I am not able to
find proper description for this key.
One key entry (r: 7, c: 5) is present in the keymap, which
is really not present in the board, removing it.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit f62349ee97 makes it possible to
have some other than first uart port as ttyS0, which breaks the workaround
serial_in_override() function which will try to address the first uart
port (for ttyS0) and not the one that was initialized.
Signed-off-by: Alexander Shishkin <virtuoso@slind.org>
CC: Mika Westerberg <ext-mika.1.westerberg@nokia.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 9905a43b made struct backlight_ops const. Omap was
setting check_fb dynamically, which caused the following
compile error:
drivers/video/backlight/omap1_bl.c: In function 'omapbl_probe':
drivers/video/backlight/omap1_bl.c:142: error: assignment of read-only variable 'omapbl_ops'
Turns out pdata->check_fb is not being used, so just remove
it to fix the compile.
Cc: Emese Revfy <re.emese@gmail.com>
Cc: Richard Purdie <rpurdie@linux.intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 35c9049b27 added
drivers/spi/omap_spi_100k.c.
This patch add the related clocks and pin muxing
entries to make the driver work on omap7xx platforms.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some chips, namely any OMAP1 chips using METHOD_MPUIO,
OMAP15xx and OMAP7xx, cannot be setup to respond to on-chip GPIO
interrupts in both rising and falling edge directions -- they can
only respond to one direction or the other, depending on how the
ICR is configured.
Additionally, current code forces rising edge detection if both
flags are specified:
if (trigger & IRQ_TYPE_EDGE_RISING)
l |= 1 << gpio;
else if (trigger & IRQ_TYPE_EDGE_FALLING)
l &= ~(1 << gpio);
else
goto bad;
This change implements a toggle function that will modify the ICR
to flip the direction of interrupt for IRQs that are requested with
both rising and falling flags. The toggle function is not called
for chips and GPIOs it does not apply to through the use of a flip_mask
that's added on a per-bank basis. The mask is only set for those
GPIOs where a toggle is necessary. Edge detection starts out the
same as above with FALLING mode first.
The toggle happens on EACH interrupt; without it, we have the
following sequence of actions on GPIO transition:
ICR GPIO Result
0x1 0 -> 1 (rising) Interrupt
0x1 1 -> 0 (falling) No interrupt
(set ICR to 0x0 manually)
0x0 0 -> 1 (rising) No interrupt
0x0 1 -> 0 (falling) Interrupt
That is, with the ICR set to 1 for a gpio, only rising edge interrupts
are caught, and with it set to 0, only falling edge interrupts are
caught. If we add in the toggle, we get this:
ICR GPIO Result
0x1 0 -> 1 (rising) Interrupt (ICR set to 0x0)
0x0 1 -> 0 (falling) Interrupt (ICR set to 0x1)
0x1 0 -> 1 ...
so, both rising and falling are caught, per the request for both
(IRQ_TYPE_EDGE_RISING | IRQ_TYPE_EDGE_FALLING).
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In its current form, the omap_mcbsp_request() function can return after
irq_request() failure without any cleanups, effectively locking out the port
forever with clocks left running. Fix it.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] __per_cpu_idtrs[] is a memory hog
[IA64] sanity in #include files. Move fnptr to types.h
[IA64] use helpers for rlimits
[IA64] cpumask_of_node() should handle -1 as a node
normal users are currently allowed to set/modify ebtables rules.
Restrict it to processes with CAP_NET_ADMIN.
Note that this cannot be reproduced with unmodified ebtables binary
because it uses SOCK_RAW.
Signed-off-by: Florian Westphal <fwestphal@astaro.com>
Cc: stable@kernel.org
Signed-off-by: Patrick McHardy <kaber@trash.net>
We need to set the LRCLK inversion bit to select DSP mode.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: stable@kernel.org
Fix the following warning, which appears when the register dump for a
faulting process is printed in a kernel with SMP, DEBUG_PREEMPT, and
DEBUG_USER (with user_debug=31) enabled:
BUG: using smp_processor_id() in preemptible [00000000] code: init/1
caller is __show_regs+0x18/0x234
Backtrace:
[<c0159e5c>] (dump_backtrace+0x0/0x114) from [<c01faf30>] (dump_stack+0x18/0x1c)
r6:c781a000 r5:c0157544 r4:00000001 r3:00000000
[<c01faf18>] (dump_stack+0x0/0x1c) from [<c01e5230>] (debug_smp_processor_id+0xc4/0xf8)
[<c01e516c>] (debug_smp_processor_id+0x0/0xf8) from [<c0157544>] (__show_regs+0x18/0x234)
r6:c781bfb0 r5:00000000 r4:c781bfb0 r3:00000000
[<c015752c>] (__show_regs+0x0/0x234) from [<c01577a0>] (show_regs+0x40/0x50)
[<c0157760>] (show_regs+0x0/0x50) from [<c015c968>] (__do_user_fault+0x5c/0xa4)
r4:c781c000 r3:00000000
[<c015c90c>] (__do_user_fault+0x0/0xa4) from [<c015cbe0>] (do_page_fault+0x1b4/0x1e4)
r7:00000000 r6:00010000 r5:c781bfb0 r4:c781c000
[<c015ca2c>] (do_page_fault+0x0/0x1e4) from [<c01554c8>] (do_DataAbort+0x3c/0xa0)
[<c015548c>] (do_DataAbort+0x0/0xa0) from [<c01560c4>] (ret_from_exception+0x0/0x10)
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This updates the U300 defconfig to include the DMA driver merged
in 2.6.33-rc1 and adds a codepage that's needed to mount VFAT MMC
cards as default. The rest is new config options.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Make registers unsigned for kernel space. This is important for
example in the perf events where the PC is stored into a u64. We
don't want it sign extended so make the regs unsigned to prevent
casts throughout the kernel.
Signed-off-by: Jamie Iles <jamie.iles@picochip.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ref counting for the bh returned by gfs2_ea_find() was
wrong. This patch ensures that we always drop the ref count
to that bh correctly.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
The rename code was taking a resource group lock in cases where
it wasn't actually needed, this caused problems if the rename
was resulting in an inode being unlinked. The patch ensures that
we only take the rgrp lock early if it is really needed.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
The VFS reads the inode size during generic_file_aio_write() but
with no locking around it. In order to get the expected result
from O_APPEND opens, this patch updated the inode size before
calling generic_file_aio_write()
There is of course still a race here, in that there is nothing to
prevent another node coming in and extending the file in the
mean time. On the other hand, when used with file locking this
will ensure that the expected results are obtained.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Collect interrupt statistics, printable via debugfs:
debugfs/omapdss/dispc_irq
debugfs/omapdss/dsi_irq
The counters are reset when printed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
- dsi_vc_send_short() needs to use dest_per for the peripheral id
- dsi_vc_send_null() was always using channel id 0
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
This patch adds support for the global device reset interrupt. Without
this change the drivers will report tx hangs on all ports when a global
device reset occurs.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds documentation for the MSCAN OF device bindings for
the MPC512x and moves the one for the MPC5200 to the new common file
"Documentation/powerpc/dts-bindings/fsl/can.txt".
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The main differences compared to the MSCAN on the MPC5200 are:
- More flexibility in choosing the CAN source clock and frequency:
Three different clock sources can be selected: "ip", "ref" or "sys".
For the latter two, a clock divider can be defined as well. If the
clock source is not specified by the device tree, we first try to
find an optimal CAN source clock based on the system clock. If that
is not possible, the reference clock will be used.
- The behavior of bus-off recovery is configurable:
To comply with the usual handling of Socket-CAN bus-off recovery,
"recovery on request" is selected (instead of automatic recovery).
Note that only MPC5121 Rev. 2 and later is supported.
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The start_xmit function of the MSCAN Driver did return improperly if
the CAN dlc check failed (skb not freed and invalid return code). This
patch adds a proper check of the frame lenght and data size and returns
now correctly. The invalid skb packets are dropped silently as suggested
by David Miller in the thread "[RFC] ndo_validate_skb: Let the netdev
check a valid skb content" on the netdev mailing list.
Furthermore, a typo has been fixed.
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
General cleanup of the ep93xx_eth driver.
1) Use pr_fmt() to prefix the module name and __func__ to the error
messages.
2) <linux/io.h> instead of <asm/io.h>
3) <mach/hardware.h> instead of <mach/ep93xx-regs.h> and <mach/platform.h>
4) Move the ep93xx_mdio_read (and ep93xx_mdio_write) function to eliminate
the function prototype.
5) Change all the printk(<level> messages to pr_<level> and remove the
__func__ argument.
6) Use platform_get_{resource/irq} to get the platform resources and add
an error check.
7) Use resource_size() for request_mem_region() and ioremap().
8) Use %pM to print the MAC address at the end of the probe.
9) Use dev->dev_addr not data->dev_addr for the MAC argument because a
random address could be used if the platform does not supply one.
The message at the end of the probe is left as a printk since it displays
cleaner without the function name that would be displayed with pr_info().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Lennert Buytenhek <kernel@wantstofly.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MSI-X table size needs to be properly set before pci_enable_msix()
is called. But on certain machines, the writes are delayed and the
MSI-X table size is incorrectly read. By reading the
BNX2_PCI_MSIX_CONTROL register, the writes are flushed and now
ensure that the MSI-X table is set correctly before MSI-X
is enable on the device.
This patch was originally diagnosed and authored by
Kalyan Ram Chintalapati <kalyanc@vmware.com>.
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Kalyan Ram Chintalapati <kalyanc@vmware.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix e1000e_rar_set() to flush consecutive register writes to avoid write
combining which some parts cannot handle. Update e1000e_init_rx_addrs()
to call the fixed e1000e_rar_set() instead of duplicating code.
Also change e1000e_rar_set() to _not_ set the Address Valid bit if the MAC
address is all zeros.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
e1000e_enable_tx_pkt_filtering() will return a non-zero value if the
driver fails to enable the manageability interface on the host for
any reason; instead it should retun zero to indicate filtering has been
disabled. Also provide a single exit point for the function.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adaptive IFS which involves writing to the Adaptive IFS Throttle register
was being done for all devices supported by the driver even though it is
not supported (i.e. the register doesn't even exist) on some devices. The
feature is supported on 8257x/82583 and ICH/PCH based devices, but not
on ESB2.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to a change in pci_restore_state()[1] which clears the saved_state
flag, the driver should call pci_save_state() to set the flag once again
to avoid issues with EEH (same fix that recently was submitted for ixgbe).
[1] commmit 4b77b0a2ba
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o If tx and rx resources are not available, during set mac request.
Then this request wont be passed to firmware and it will be added to
driver mac list and will never make it to firmware.
So if resources are not available, don't add it to driver mac list.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o While unloading driver or resetting the context, tx ring was not
getting free.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch "sbawe: fix memory detection" fixed detection
for memoryless SB32 cards but broke detection of memory
above 512KB. This patch fixes the regression.
The patch has been tested on the SB32 card (CT3670) with
0MB, 2MB and 8MB memory installed.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The problem is that in the original code sound_nblocks could go up to 1024
which would be an array overflow.
This was found with a static checker and has been compile tested only.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The patch implements a firmware command to fetch the eeprom data.
Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use DEFINE_PCI_DEVICE_TABLE() so we get place PCI ids table into correct section
in every case.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If for any reason we haven't installed handler we shouldn't try to
enable IRQ/MSI on the hw so we don't get unhandled IRQ/MSI which
makes the kernel sad.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In some case vblank might not be initialized and we shouldn't
try to use associated function. This patch make sure this is
the case. It also export drm_vblank_cleanup so driver can cleanup
vblank if for any reason IRQ/MSI is not working.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
