Move the SPI and I2C specific write callbacks to the respective
"#if IS_ENABLED(CONFIG_SPI_MASTER)" and "#if IS_ENABLED(CONFIG_I2C)"
protected sections of the code.
This fixes the following warning which occurs if CONFIG_I2C is not set:
drivers/iio/dac/ad5064.c: In function ‘ad5064_i2c_write’:
drivers/iio/dac/ad5064.c:132: error: implicit declaration of function ‘i2c_master_send’
And the follwing warning which occurs when CONFIG_SPI_MASTER is not set:
drivers/iio/dac/ad5064.c:137: warning: ‘ad5064_spi_write’ defined but not used
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
It is possible that on one of the error paths we are going to try to free
'rxbuf', even though it has not been allocated yet, which cause the following
warning:
drivers/staging/iio/adc/max1363_ring.c: In function 'max1363_trigger_handler':
drivers/staging/iio/adc/max1363_ring.c:87:7: warning: 'rxbuf' may be used
uninitialized in this function
Reported-by: Fengguang Wu <wfg@linux.intel.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
sensor has 4 channels (10-bit each, R/G/B and clear), sensitivity
and gain is controlled in the driver by ext_info integration_time
and CHAN_INFO_HARDWAREGAIN
driver supports triggered buffer and IIO_CHAN_INFO_RAW to get the
sensor data
v5: address comments by Jonathan Cameron
* use macro for channel declaration
* get timestamp right before measurement
* cleanups
v4: address comments by Lars-Peter Clausen
* make sure trigger handler is exited with iio_trigger_notify_done()
and IRQ_HANDLED
* kfree()/kalloc() -> krealloc()
v3:
* fix warnings
v2: address comments by Lars-Peter Clausen
* buffer allocation now in update_scan_mode instead of in trigger
handler
* simplify trigger code (assume active_scan_mask is not empty, use
for_each_set_bit, use iio_push_to_buffer)
* reorder entry in Makefile and Kconfig
* fix remove
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
From Shawn Guo <shawn.guo@linaro.org>:
Here is the second (last) batch of mxs mxs device tree changes for 3.6.
* 'mxs/dt-for-3.6' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: dts: imx28-evk: add usb devices
ARM: mxs: rename dts files with soc name being the prefix
ARM: apx4devkit: add pin muxing for GPIOs
ARM: apx4devkit: remove AUART3
ARM: apx4devkit: add SSP2 support
ARM: apx4devkit: fix the bus-width of SSP0 to 4 bits
ARM: apx4devkit: add display support
ARM: apx4devkit: add NAND support
ARM: mxs: add dtb-y target into Makefile.boot
ARM: mxs: convert stmp378x_devb board to device tree
ARM: mxs: convert tx28 board to device tree
ARM: mxs: convert apx4devkit board to device tree
ARM: mxs: convert m28evk board to device tree
ARM: dts: imx28: move lcdif control pins into board dts
ARM: dts: imx28: move extra gpmi-nand pins into board dts
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=CD8C
-----END PGP SIGNATURE-----
Merge tag 'imx-defconfig' of git://git.pengutronix.de/git/imx/linux-2.6 into next/defconfig
From Sascha Hauer <s.hauer@pengutronix.de>:
ARM i.MX defconfig updates for v3.6
* tag 'imx-defconfig' of git://git.pengutronix.de/git/imx/linux-2.6:
ARM: imx_v4_v5_defconfig: update features
ARM: imx_v6_v7_defconfig: update features
Includes an update to v3.5-rc5
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Shawn Guo <shawn.guo@linaro.org>:
Here is the second (last) batch of imx device tree changes for 3.6.
* 'imx/dt-for-3.6' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: imx6q: ensure ANATOP controller is available
ARM: dts: imx6q-sabrelite: add ecspi1 pinctrl support
ARM: dts: imx6q-sabrelite: add usb devices
ARM: imx6q: disable usb charger detector
ARM: imx6q: add usbphy clocks
ARM: imx6q: add usb controller clock lookups
ARM: dts: imx: update #interrupt-cells for gpio nodes
bindings: update imx and mxs #gpio-cells
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Sascha Hauer <s.hauer@pengutronix.de>:
ARM i.MX dt updates for v3.6
* tag 'imx-dt' of git://git.pengutronix.de/git/imx/linux-2.6:
arm/dts: Add support for i.MX31 bug 1.x board from buglabs.
ARM i.MX31: Add devicetree support
ARM: dts: Add basic support for mx27_3ds board
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Tony Lindgren <tony@atomide.com>:
Device tree related patches for omaps
* tag 'omap-devel-dt-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
arm/dts: New dts file for PandaBoardES (4460)
arm/dts: omap4-panda: Audio support for PandaBoard 4430
arm/dts: omap4-sdp: Enable audio support via device tree
arm/dts: omap4-sdp: Add support for twl6040
arm/dts: omap4-sdp: Add fixed regulator to represent VBAT
arm/dts: omap4: Add entry for OMAP DMIC IP
arm/dts: omap4: Add entry for OMAP McPDM IP
arm/dts: am33xx wdt node
arm/dts: remove MMC/SD and SPI related entries from am33xx.dtsi
watchdog: omap_wdt: add device tree support
ARM: OMAP: avoid build wdt platform device if with dt support
arm/dts: add wdt node for omap3 and omap4
arm/dts: OMAP4: Add Variscite OMAP4 System-On-Modeule support
arm/dts: Add support for AM335x BeagleBone
arm/dts: Add support for AM335x EVM
arm/dts: Add initial DT support for AM33XX SoC family
arm/dts: omap3-evm: Add i2c and twl4030 support
arm/dts: Add support for TI AM3517/05 EVM board
arm/dts: OMAP2: Add support for OMAP2420H4 Board
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Nicolas Ferre <nicolas.ferre@atmel.com>:
Two new boards described with device tree
* tag 'at91-for-next-dt' of git://github.com/at91linux/linux-at91:
ARM: at91: Add support for board aks-cdu
ARM: at91: add support for Telit EVK-PRO3 with Telit GE863-PRO3
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This branch contains changes to Tegra device tree files, and related
Kconfig and Makefile changes. Highlights are:
* New support for the Whistler board.
* Use of the I2C pinctrl-based bus mux on Seaboard/Springbank.
This branch is based on Tegra's for-3.6/cleanup branch from a previous
pull request.
* 'for-3.6/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: dt: tegra seaboard: move battery monitor to mux'd I2C bus.
ARM: dt: tegra: seaboard: instantiate pinctrl-based I2C bus mux
ARM: dt: tegra: add Whistler device tree file
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=44461
Signed-off-by: Alan Cox <alan@linux.intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Imported from mailing list
* picoxcell/timer:
clocksource: dw_apb_timer: Add common DTS glue for dw_apb_timer
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Make a common device tree glue for clocksource/dw_apb_timer.
Move mach-picoxcell/time.c to be a generic device tree application
of the dw_apb_timer.
Configure mach-picoxcell to use the dw_apb_timer_of device tree
implementation in drivers/clocksource.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Entries that are in a sunrpc cache but are not valid should be reported
with a leading '#' so they look like a comment.
Commit d202cce896 (sunrpc: never return expired entries in sunrpc_cache_lookup)
broke this for expired entries.
This particularly applies to entries that have been replaced by newer entries.
sunrpc_cache_update sets the expiry of the replaced entry to '0', but it
remains in the cache until the next 'cache_clean'.
The result is that if you
echo 0 2000000000 1 0 > /proc/net/rpc/auth.unix.gid/channel
several times, then
cat /proc/net/rpc/auth.unix.gid/content
It will display multiple entries for the one uid, which is at least confusing:
#uid cnt: gids...
0 1: 0
0 1: 0
0 1: 0
With this patch, expired entries are marked as comments so you get
#uid cnt: gids...
0 1: 0
# 0 1: 0
# 0 1: 0
These expired entries will never be seen by cache_check() as they are always
*after* a non-expired entry with the same key - so the extra check is only
needed in c_show()
Signed-off-by: NeilBrown <neilb@suse.de>
--
It's not a big problem, but it had me confused for a while, so it could
well confuse others.
Thanks,
NeilBrown
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
... in preparation for common clock coming for Integrator
and Versatile Express.
Based on Linus Walleij's "ARM: integrator: convert to common
clock" patch.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
With recent enough motherboard firmware, core tile can be fitted
in either of the two daughterboard sites. The non-DT tile code for
V2P-CA9 did not check that when configuring DVI output nor setting
CLCD pixel clock.
Fixed now, providing "get master site" API in motherboard's code.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
The vexpress Kconfig setup tries to be clever^Whelpful and selects some
errata workarounds for certain revisions of the Cortex-A9 and PL310,
which may be required depending on the core tile.
Since the mach-vexpress can support A5, A7 and A15 coretiles, let's
make errata workaround selection optional.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Rob Herring <robherring2@gmail.com>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
After FW download, activate new FW by invoking FW reset.
Recreate rings once new FW is operational.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Invoke only required initialization routines for Lancer.
Remove invocation of unnecessary routines.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Query die temperature stat for Lancer to report it correctly
in ethtool.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Autonegotiation of pause parameters is possible only on some PHYs.
Ability of autoneg of pause parameters is reported by adapter.
Autoneg of pause parameters cannot be changed from driver.
Fix driver to give error when autoneg mode is toggled by user.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In SGMII riser card different PHY chip are used with different external
IRQ from eTSEC. To support PHY link state auto detect in SGMII mode we
should add another group of PHY nodes for SGMII mode.
For MPC8572DS IRQ6 is used for PHY0~PHY1, IRQ7 is used for PHY2~PHY3.
For MPC8544DS and MPC8536DS IRQ6 is used for PHY0~PHY1.
For P2020DS IRQ5 is used for PHY1~PHY2.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jia Hongtao <B38951@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
All handler->err() routines expect that we've done a pskb_may_pull()
test to make sure that IP header length + 8 bytes can be safely
pulled.
Reported-by: Hiroaki SHIMODA <shimoda.hiroaki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Can be used to match packets against netfilter ip sets created via ipset(8).
skb->sk_iif is used as 'incoming interface', skb->dev is 'outgoing interface'.
Since ipset is usually called from netfilter, the ematch
initializes a fake xt_action_param, pulls the ip header into the
linear area and also sets skb->data to the IP header (otherwise
matching Layer 4 set types doesn't work).
Tested-by: Mr Dash Four <mr.dash.four@googlemail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
First update the adapter variables with the current speed and
mode before fire the notification. Otherwise, the get_settings()
may provide old values.
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Acked-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6lowpan module starts collecting incomming frames and fragments
right after lowpan_module_init() therefor it will be better to
clean unfinished fragments in lowpan_cleanup_module() function
instead of doing it when link goes down.
Changed spinlocks type to prevent deadlock with expired timer event
and removed unused one.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function lowpan_alloc_new_frame() takes u8 tag as an argument. However,
its only caller, lowpan_process_data() passes down a u16. Hence,
the tag value can get corrupted. This prevent 6lowpan fragment reassembly of a
message when the fragment tag value is over 256.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Cc: Tony Cheneau <tony.cheneau@amnesiak.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make symbols static to avoid the following warning shown up
by sparse:
warning: symbol ... was not declared. Should it be static?
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use netdev_alloc_skb_ip_align() instead of alloc_skb() to get some
extra headroom in case we need to forward this frame in a tunnel or
something else.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add method to get the device short 802.15.4 address. This call
needed by ieee802154 layer to satisfy 'iz list' request from
the user space.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix LOCKDEP bug message for the irq handler spinlock.
Make the irq processing code more explicit and stable.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Revert the commit 768f7c7c12 to initialize
spinlock in the more preferable way and make it static to avoid sparse
warning.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"retval" has to be a signed integer for the error handling to work.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of older ColdFire CPU based boards use NS8390 based network
controllers. Most use the Davicom 9008F or the UMC 9008F. This driver
provides the support code to get these devices working on these platforms.
Generally the NS8390 based eth device is direct connected via the general
purpose bus of the ColdFire CPU. So its addressing and interrupt setup is
fixed on each of the different platforms (classic platform setup).
This driver is based on the other drivers/net/ethernet/8390 drivers, and
includes the lib8390.c code. It uses the existing definitions of the
board NS8390 device addresses, interrupts and access types from the
arch/m68k/include/asm/mcf8390.h, but moves the IO access functions into
the driver code and out of that header.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mcfne.h include contains definitions to support NS8390 eth based hardware
on ColdFire based CPU boards. So change its name to reflect that better.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this change, running AP + station on the same wiphy
does not work since the commit "cfg80211: add channel checking
for iface combinations". The stopped AP prevents the client
from connecting to an AP on a different channel.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[line-break commit message to < 72 chars]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With the default name table size of 1024, it is possible that
the sanity check in tipc_nametbl_stop could spam out 1024
essentially identical error messages if memory was corrupted
or similar. Limit it to issuing no more than a single message.
The actual chain number (i.e. 0 --> 1023) wouldn't provide any
useful insight if/when such an instance happened, so don't
bother printing out that value.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
