According to the datasheet[1]
Register 0x06h Description: RmpCtrl (REGISTER ADDRESS: 0x06h Read/Write)
BIT[5..7]:
RMP[2:0] Output voltage ramp timing
D7-D5 Slope
000 32mV/us
001 16mV/us
010 8mV/us
...
110 0.5mV/us
111 0.25mV/us
Thus to get correct ramp_ctrl value, we need to right-shift 5 bits.
[1] http://www.ti.com/lit/ds/symlink/tps62360.pdf
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Kay Sievers reported that coreutils' stat tool has a problem with
s390's statfs[64] definition:
> The definition of struct statfs::f_type needs a fix. s390 is the only
> architecture in the kernel that uses an int and expects magic
> constants lager than INT_MAX to fit into.
>
> A fix is needed to make Fedora boot on s390, it currently fails to do
> so. Userspace does not want to add code to paper-over this issue.
[...]
> Even coreutils cannot handle it:
> #define RAMFS_MAGIC 0x858458f6
> # stat -f -c%t /
> ffffffff858458f6
>
> #define BTRFS_SUPER_MAGIC 0x9123683E
> # stat -f -c%t /mnt
> ffffffff9123683e
The bug is caused by an implicit sign extension within the stat tool:
out_uint_x (pformat, prefix_len, statfsbuf->f_type);
where the format finally will be "%lx".
A similar problem can be found in the 'tail' tool.
s390 is the only architecture which has an int type f_type member in
struct statfs[64]. Other architectures have either unsigned ints or
long values, so that the problem doesn't occur there.
Therefore change the type of the f_type member to unsigned int, so
that we get zero extension instead of sign extension when assignment to
a long value happens.
This patch changes the s390 uapi struct stafs[64] definition in the kernel
to contain only unsigned values.
This was true for 32 bit builds anyway, since we use the generic uapi
header file in that case. So lets not include conditionally the generic
uapi header file but have the s390 implementation completely independent.
Also fix the types of struct compat_stafs to match reality and move the
definition of struct compat_statfs64 to asm/compat.h since it is not part
of the api.
Reported-by: Kay Sievers <kay@vrfy.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
For offset > PAGE_SIZE, s390_dma_map_pages() will issue a warning
and return a wrong dma address.
This patch removes the warning and fixes the dma return address
calculation.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The compat definitions are not part of the uapi. So move them to
s390's private compat header file.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix this one for !COMPAT:
compat.h: In function ‘arch_compat_alloc_user_space’:
compat.h:292:2: error: implicit declaration of function ‘is_compat_task’
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The f_spare field within struct compat_statfs is four bytes larger
than within the native 31 bit struct statfs.
compat_sys_statfs() clears the f_spare field in user space which
means that in compat mode four bytes that are behind the user space
supplied struct compat_statfs will be corrupted (zeroed).
According to Thomas Gleixner's Linux 2.6 history tree this bug is
present since v2.5.74 87880da124 "[PATCH] s390: 31 bit compat.".
So it get's fixed shortly before its 10th anniversary. Tough luck.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Currently always one page is copied to a user buffer for the last
HSA block in memcpy_hsa(). Now the correct length is used.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The gmap_map_segment function creates a special invalid segment table
entry with the address of the requested target location in the process
address space. The first access will create the connection between the
gmap segment table and the target page table of the main process.
If two threads do this concurrently both will walk the page tables and
allocate a gmap_rmap structure for the same segment table entry.
To avoid the race recheck the segment table entry after taking to page
table lock.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Implement gmap_translate() function which translates a guest absolute address
to a user space process address without establishing the guest page table
entries.
This is useful for kvm guest address translations where no memory access
is expected to happen soon (e.g. tprot exception handler).
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull MIPS fix from Ralf Baechle:
"Revert the change of the definition of PAGE_MASK which was prettier
but broke a few relativly rare platforms"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
Revert "MIPS: page.h: Provide more readable definition for PAGE_MASK."
The intend of this patch is to improve the support of the dib7090 and
dib7790. The AGC1 min value is set to 32768 by default. The actual AGC1 min
and the external attenuation are controled depending on the received RF
level.
Signed-off-by: Olivier Grenie <olivier.grenie@parrot.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@parrot.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The intend of this patch is to remove the support for the dib7090E. The
DiB7090E-package has never left prototype state and never made it to
mass-prod-state.
Signed-off-by: Olivier Grenie <olivier.grenie@parrot.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@parrot.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The intend of this patch is to improve the support of the dib8096. The PLL
parameters are not automatically computed. The limit to set/unset external
diode for attenuation has been updated. The TFE8096P board is using the
new I2C API.
Signed-off-by: Olivier Grenie <olivier.grenie@parrot.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@parrot.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The intend of this patch is to improve the support of the dib0090 tuner.
The ramp tables have been updated. Also some minor enhancements has been
added (EFUSE and reset).
Signed-off-by: Olivier Grenie <olivier.grenie@parrot.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@parrot.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The intend of this patch is to improve the support of the dib7000p. It is
now possible to set the minimum value for the AGC1. Also, the driver takes
into account the frequency offset introduced in the tuned frequency.
Signed-off-by: Olivier Grenie <olivier.grenie@parrot.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@parrot.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Recently I changed the SETCLIENTID code to use AUTH_GSS(krb5i), and
then retry with AUTH_NONE if that didn't work. This was to enable
Kerberos NFS mounts to work without forcing Linux NFS clients to
have a keytab on hand.
Rick Macklem reports that the FreeBSD server accepts AUTH_NONE only
for NULL operations (thus certainly not for SETCLIENTID). Falling
back to AUTH_NONE means our proposed 3.10 NFS client will not
interoperate with FreeBSD servers over NFSv4 unless Kerberos is
fully configured on both ends.
If the Linux client falls back to using AUTH_SYS instead for
SETCLIENTID, all should work fine as long as the NFS server is
configured to allow AUTH_SYS for SETCLIENTID.
This may still prevent access to Kerberos-only FreeBSD servers by
Linux clients with no keytab. Rick is of the opinion that the
security settings the server applies to its pseudo-fs should also
apply to the SETCLIENTID operation.
Linux and Solaris NFS servers do not place that limitation on
SETCLIENTID. The security settings for the server's pseudo-fs are
determined automatically as the union of security flavors allowed on
real exports, as recommended by RFC 3530bis; and the flavors allowed
for SETCLIENTID are all flavors supported by the respective server
implementation.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The intend of this patch is to improve the support of the dib8000.
Signed-off-by: Olivier Grenie <olivier.grenie@parrot.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@parrot.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by Rob Herring[1] there were some mismatched types between
drivers/clk/ux500/clk.h and the corresponding function definitions:
drivers/clk/ux500/clk-prcc.c:145:13: error: conflicting types for 'clk_reg_prcc_pclk'
drivers/clk/ux500/clk-prcc.c:155:13: error: conflicting types for 'clk_reg_prcc_kclk'
[1] http://article.gmane.org/gmane.linux.ports.arm.kernel/232246
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Cc: Rob Herring <robherring2@gmail.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
commit 7ec98e15aa (timekeeping: Delay update of clock->cycle_last)
forgot to update tk->cycle_last in the resume path. This results in a
stale value versus clock->cycle_last and prevents resume in the worst
case.
Reported-by: Jiri Slaby <jslaby@suse.cz>
Reported-and-tested-by: Borislav Petkov <bp@alien8.de>
Acked-by: John Stultz <john.stultz@linaro.org>
Cc: Linux-pm mailing list <linux-pm@lists.linux-foundation.org>
Link: http://lkml.kernel.org/r/alpine.LFD.2.02.1304211648150.21884@ionos
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
If we're not maxed out then oz_get_pd_list() leaves part of the "list"
struct uninitialized. We should clear this so that no stack information
is leaked to userspace.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If "nd->nd_vpd_len" is less than 512 then the last part of the
"vpd.vpd_data" has uninitialized stack information. We need to clear it
before copying the buffer to user space.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All the RTC dma support code in this driver is #ifdef'ed out.
Remove the unused code to assist in cleaning up this driver.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All the RTC dma support code in this driver is #ifdef'ed out.
Remove the unused code to assist in cleaning up this driver.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver core already takes care of refcounting, no need to do this on
driver level again.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit c17a655478.
Manuel Lauss writes:
lmo commit c17a6554 (MIPS: page.h: Provide more readable definition for
PAGE_MASK) apparently breaks ioremap of 36-bit addresses on my Alchemy
systems (PCI and PCMCIA) The reason is that in arch/mips/mm/ioremap.c
line 157 (phys_addr &= PAGE_MASK) bits 32-35 are cut off. Seems the
new PAGE_MASK is explicitly 32bit, or one could make it signed instead
of unsigned long.
We should always clear it before initiating file recovery.
Also ensure that we clear it after a CLOSE and/or after TEST_STATEID fails.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Pull crypto fix from Herbert Xu:
"This fixes a kernel memory leak in the algif interface"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: algif - suppress sending source address information in recvmsg
commit 61ff5d69 "em28xx: improve em2710/em2820 distinction" missed the
le16_to_cpu conversion of the USB vendor ID.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Because they're signed, "is_video" and "is_audio" can be 0 and -1
instead of 0 and 1 as intended. It doesn't cause a bug, but it makes
Sparse complain:
drivers/staging/media/go7007/go7007-priv.h:94:31: error: dubious one-bit signed bitfield
drivers/staging/media/go7007/go7007-priv.h:95:31: error: dubious one-bit signed bitfield
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Legacy PCI suspend-resume handlers are called with interrupts enabled.
But cx8800_suspend/cx8800_resume and
cx8802_suspend_common/cx8802_resume_common use spin_lock/spin_unlock
functions to acquire dev->slock, while the same lock is acquired in the
corresponding irq-handlers: cx8800_irq and cx8802_irq.
That means a deadlock is possible if an interrupt happens while suspend
or resume owns the lock. The patch replaces spin_lock/spin_unlock with
spin_lock_irqsave/spin_unlock_irqrestore.
Found by Linux Driver Verification project (linuxtesting.org).
[mchehab@redhat.com: Fix CodingStyle]
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Sparse complains that these are "dubious one-bit signed bitfields" and
the comment says it was intended to be 1 and 0 instead of -1 and 0.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Datasheet says:
Time Step (TSTEP) selection, when changing the output voltage, the new value is
reached through successive voltage steps (if not bypassed). The equivalent
programmable slew rate of the output voltage is:
TSTEP[1:0]: 00 Jump (no slope control)
TSTEP[1:0]: 01 10mV/us
TSTEP[1:0]: 10 5mV/us (default)
TSTEP[1:0]: 11 2.5mV/us
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The ctrl_addr setting for SMPS10 is missed, thus palmas_smps_init() read/write
wrong register for SMPS10 in current code. Fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently we decide if the _BQC is using index by first setting the
level to maximum, and then check if _BQC returned maximum; if not, we
say it is using index.
This is not true for some buggy systems, where the _BQC method will
always return a constant value(e.g. 0 or 100 for the two broken system)
and thus break the current logic. So this patch tries to enhance the
quirk detect logic for _BQC: we do this by picking a test_level, it can
be the maximum level or the mininum one based on some condition. And we
don't make the assumption that if _BQC returned a value that is not what
we just set, it must be using an index. Instead, we will compare the
value returned from _BQC and if it doesn't match, see if the returned
value is an index. And if still no, clear the capability of _BQC.
References: https://bugzilla.kernel.org/show_bug.cgi?id=42861
References: https://bugzilla.kernel.org/show_bug.cgi?id=56011
Reported-and-tested-by: Artem Savkov <artem.savkov@gmail.com>
Reported-by: Luis Medinas <lmedinas@gmail.com>
Reported-by: Cheppes <cheppes@mailinator.com>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The builtin .dtb.S intermediate file needs to be marked with .SECONDARY
so that it isn't automatically deleted (which causes it to be
regenerated on every build). Also add *.dtb.S to clean-files so it gets
cleaned up by make clean.
Similarly, if the specified builtin dtb isn't already in dtb-y (e.g.
imported into the tree and specified in CONFIG_METAG_BUILTIN_DTB_NAME)
it too will be treated as an intermediate and deleted automatically
(again causing it to be regenerated on every build), so add it to dtb-y
so it gets added to targets and the dtbs target.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Vineet Gupta <Vineet.Gupta1@synopsys.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Michal Marek <mmarek@suse.cz>
Cc: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Borislav Petkov reported a lockdep splat warning about kzalloc()
done in an IPI (hardirq) handler.
This is a real bug, do not call kzalloc() in a smp_call_function_single()
handler because it can schedule and crash.
Reported-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Jacob Shin <jacob.shin@amd.com>
Tested-by: Borislav Petkov <bp@suse.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: <eranian@google.com>
Cc: <a.p.zijlstra@chello.nl>
Cc: <acme@ghostprotocols.net>
Cc: <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/20130421180627.GA21049@jshin-Toonie
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In a previous commit the en_core_tk_irqen flag has been added but we missed
the cpuidle_wrap_enter which was doing the job to measure the time for the
'omap3_enter_idle' function.
Actually, I don't see any reason to use this wrapper in the code. In the better
case, the time computation is not correctly done because of the different
operations done in omap3_enter_idle_bm which were not taken into account
before the en_core_tk_irqen flag was set.
As the time is reflected for the state overridden by the omap3_enter_idle_bm,
using the wrapper is pointless now, so removing it.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 688036b538 removed the function
'shmobile_enter_wfi' but we forgot to remove the definition in the header file.
Note this function is just an alias to 'cpu_do_idle()' wrapped into a cpuidle
function callback prototype which already exists with the default WFI state
and the arm_simple_enter function.
Remove the function prototype.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Remove the shmobile_enter_wfi function which is the same as the
common WFI enter function from the arm cpuidle driver defined
with the ARM_CPUIDLE_WFI_STATE macro.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Parent node must be put after using it to balance its usage count. This was
missing in cpufreq-cpu0 driver. Fix it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This driver isn't updated to work with latest cpufreq core updates that happened
recently. Fix them.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
DT nodes should be put using of_node_put() to balance their usage counts. This
is not done properly in ARM's big LITTLE driver. Fix it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some cpufreq drivers implement their own governor and so don't need
us to call generic governors interface via __cpufreq_governor(). Few
recent commits haven't obeyed this law well and we saw some
regressions.
This patch is an attempt to fix the above issue.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reported-and-tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Tested-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Registering the driver, or the device, can fail, let's check the return code
and return the error code to the PM layer.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Like all the other drivers, let's initialize the structure a compile time
instead of init time.
The states #1 and #2 are not enabled by default. The init function will
check the features of the board in order to enable the state.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
