We'll need that function for IBSS station management,
so pass it the address, which is the only thing it
uses from the station struct.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
iwl3945 should not use iwl_add_local_station(..., false)
because that would leave the IWL_STA_UCODE_INPROGRESS flag
set for the station, which is not desirable. Instead it
can use iwl3945_add_bcast_station() here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
When adding the broadcast station the link quality command is
generated on demand, sent to device, and disappears. It is thus not
available for later cases when we need to restore stations and need
to send the link quality command afterwards. Now, when first adding the
broadcast station, also generate its link quality command to always be
available for later restoring.
Also fix an issue when adding local stations where the "in progress" state
is never cleared.
Reported-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Dump the firmware version and build number in case of firmware SW
error. This would help firmware engineer analyze the error log.
Requested-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Multiple error condition require fw/rf reset, driver should check all
the possible errors as long as the error checking functions for the
devices are available.
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
wifi/wimax co-exist command is part of _agn device configuration
sequence; move it to iwl-agn-ucode.c which is more appropriate place for the
function.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Return -EAGAIN when request tx power information and uCode is not ready;
so it will not confuse with tx power information not available.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
sensitivity calibration and chain noise calibration are not available
for all the devices; use .cfg to configure the availability of those
calibration functions
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Instead of checking device type for enable/disable continuous ucode
trace function; put it in .cfg for better control and more
flexibilities.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Instead of checking device type for enable/disable tx power control,
move it to .cfg for better control and more flexibilities.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
The iw_mode will always follow the only vif we
have, but using the vif directly seems easier.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
The "chain_tx_power" debugfs function is to display the tx power per
chain based. Name it "tx_power" is misleading.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
For the devices do not have power save support, remove the power save
control related debugfs files.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Rename the current 6000 series Gen2 devices to Gen2a.
Rename the ucode name prefix to iwlwifi-6000g2a.
Also corrected the device IDs for Gen2a series devices.
Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
When we kick off a firmware loading process,
and then unbind from the pci device right
away, we get into trouble. Avoid that by
waiting for the firmware loading to finish
(whether successfully or not) before the
unbind in iwl_pci_remove.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Replace the introduced i_sem by an i_mutex in the filesystem locking
documentation. This was introduced [1] after all occurrences were
already replaced in the same text [2]. However, the term "inode
semaphore" has not been replaced then, and it's replaced now.
[1] afddba49d1
[2] a7bc02f4f4
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The i386 subarch happens to pull in original NR_syscalls. Maybe we can
make that work for all host arch, but for now just avoid the clash by
using an all-upper-case name.
CC arch/um/kernel/skas/syscall.o/data/linux-2.6/arch/um/kernel/skas/syscall.c:13:1: warning: "NR_syscalls" redefined
In file included from /data/linux-2.6/arch/x86/include/asm/unistd.h:3,
from /data/linux-2.6/arch/um/sys-i386/shared/sysdep/syscalls.h:6,
from /data/linux-2.6/arch/um/kernel/skas/syscall.c:10:
/data/linux-2.6/arch/x86/include/asm/unistd_32.h:349:1: warning: this is the location of the previous definition
Signed-off-by: Jan Kiszka <jan.kiszka@web.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Update stale comments regarding locking order and add a little more detail
so it's easier to follow the locking between the cgroup freezer and the
power management freezer code.
Signed-off-by: Matt Helsley <matthltc@us.ibm.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Currently the default runtime PM callbacks for platform devices return
-ENOSYS, preventing the use of runtime PM platforms until they have
provided at least a default implementation. This hinders the use of
runtime PM by devices which work with many platforms such as memory
mapped devices, MFDs and on chip IPs shared by multiple architectures.
Change the default implementation to the standard pm_generic_runtime
one, allowing drivers to use runtime PM without per-architecture
changes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
There are three issues with the i2c bus type's power management
callbacks at the moment. First, they don't include any hibernate
callbacks, although they should at least include the .restore()
callback (there's no guarantee that the driver will be present in
memory before loading the image kernel and we must restore the
pre-hibernation state of the device). Second, the "legacy"
callbacks are not going to be invoked by the PM core since the bus
type's pm object is not NULL. Finally, the system sleep PM
(ie. suspend/resume) callbacks don't check if the device has been
already suspended at run time, in which case they should skip
suspending it. Also, it looks like the i2c bus type can use the
generic subsystem-level runtime PM callbacks.
For these reasons, rework the system sleep PM callbacks provided by
the i2c bus type to handle hibernation correctly and to invoke the
"legacy" callbacks for drivers that provide them. In addition to
that make the i2c bus type use the generic subsystem-level runtime
PM callbacks.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
This patch changes the string based list management to a handle base
implementation to help with the hot path use of pm-qos, it also renames
much of the API to use "request" as opposed to "requirement" that was
used in the initial implementation. I did this because request more
accurately represents what it actually does.
Also, I added a string based ABI for users wanting to use a string
interface. So if the user writes 0xDDDDDDDD formatted hex it will be
accepted by the interface. (someone asked me for it and I don't think
it hurts anything.)
This patch updates some documentation input I got from Randy.
Signed-off-by: markgross <mgross@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Fix printk format warning in block_io.c:
kernel/power/block_io.c:41: warning: format '%ld' expects type 'long int', but argument 2 has type 'sector_t'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Move all the swap processing into one function. It will make swap
calls from a non-swap code easier.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The first sector knowledge is swap-only specific. Move it into the
swap handle. This will be needed for later non-swap specific code
moving into snapshot.c.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Move block I/O operations to a separate file. It is because it will
be used later not only by the swap writer.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Remove support of reads with offset. This means snapshot_read/write_next
now does not accept count parameter. It allows to clean up the functions
and snapshot handle which no longer needs to care about offsets.
/dev/snapshot handler is converted to simple_{read_from,write_to}_buffer
which take care of offsets.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
It will be used in suspend code and serves as an easy wrap around
copy_from_user. Similar to simple_read_from_buffer, it takes care
of transfers with proper lengths depending on available and count
parameters and advances ppos appropriately.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Opening and closing /dev/snapshot causes the kernel to carry out
some hibernate preparations that should be documented.
[rjw: Added the changelog.]
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Add a few sysfs files relating to runtime power management for
advanced debug purposes:
runtime_enabled: is runtime PM enabled for this device? States
are "enabled", "disabled", "forbidden" or a combination
of the latter two.
runtime_status: what state is the device in currently? E.g., it
reports "suspended" for runtime-suspended devices, and
"active" for active devices. NOTE: if runtime_enabled
returns "disabled", the value of this file may not
reflect its physical state.
runtime_usage: the runtime PM usage count of a device
runtime_active_kids: the runtime PM children usage count of a device, or
0 if the ignore_children flag is set.
Also, CONFIG_PM_SLEEP_ADVANCED_DEBUG is not defined in any Kconfig
file, so replace it with CONFIG_PM_ADVANCED_DEBUG.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Improve the device power management document after it's been
updated by the previous patch.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The device PM document, Documentation/power/devices.txt, is badly
outdated and requires total rework to fit the current design of the
PM framework. Make it more up to date.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Randy Dunlap <randy.dunlap@oracle.com>
This patch (as1361) changes the runtime PM interface slightly; it
allows suspend requests to be scheduled while the runtime_suspend
method is running. If the method succeeds then the scheduled request
is cancelled, whereas if the method fails then an idle notification is
sent only if no request was scheduled.
Being able to schedule suspend requests from within a runtime_suspend
method is useful for drivers that need to test for idleness and
suspend the device all while holding a single spinlock, or for drivers
that want to check for idleness by polling.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Also change couple of stubs implemented as macros in !CONFIG_PM case
in statinc inline functions to provide proper typechecking of
arguments regardless of config.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The proper constraint for a receiving 8-bit variable is "=qm", not
"=g" which equals "=rim"; even though the "i" will never match, bugs
can and do happen due to the difference between "q" and "r".
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Avi Kivity <avi@redhat.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <1273135546-29690-2-git-send-email-avi@redhat.com>
Unbreak FPU emulation, broken by checkin
8660328332:
x86: Introduce 'struct fpu' and related API
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Avi Kivity <avi@redhat.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <1273135546-29690-3-git-send-email-avi@redhat.com>
When CONFIG_NET is disabled, the attempt to build wext-priv.c
fails with:
net/wireless/wext-priv.c: In function 'ioctl_private_call':
net/wireless/wext-priv.c:207: error: implicit declaration of function 'call_commit_handler'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
s/X/x
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With a little bit of restructuring it isn't necessary to have special
cases in rt2x00queue_write_tx_descriptor for writing the descriptor
for beacons.
Simply split off the kicking of the TX queue to a separate function
with is only called for non-beacons.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
According to the Ralink vendor driver for rt2800 we don't need a full
TXD for a beacon but just a TXWI in front of the actual beacon.
Fix the rt2800pci and rt2800usb beaconing code accordingly.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Preparation to fix rt2800 beaconing.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All of the driver's kick_tx_queue callback functions treat the TX queue
for beacons in a special manner.
Clean this up by integrating the kicking of the beacon queue into the
write_beacon callback function, and let the generic code no longer call
the kick_tx_queue callback function when updating the beacon.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RXWI processing is exactly the same for rt2800pci and rt2800usb, so
make it common code.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TXWI writing is exactly the same for rt2800pci and rt2800usb, so
make it common code.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We should simply follow what the hardware told us it has done.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove unused RXD_DESC_SIZE define and remove duplicated RXWI definitions
from rt2800.h.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We should take the stripping of the IV into account for the txdesc->length
field.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Tested-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are several places that use > ARRAY_SIZE() instead of
>= ARRAY_SIZE().
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I changed "> ATH9K_HTC_MAX_TID" to ">= ATH9K_HTC_MAX_TID" to avoid a
potential overflow.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
