This patch fixes a bug in ixgbe_ptp_check_pps_event where the type was
uninitialized and could cause unknown event outcomes.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
This series contains updates to ixgbe, ixgbevf, igbvf, igb and
networking core (bridge). Most notably is the addition of support
for local link multicast addresses in SR-IOV mode to the networking
core.
Also note, the ixgbe patch "ixgbe: Add support for pipeline reset" and
"ixgbe: Fix return value from macvlan filter function" is revised based
on community feedback.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_<level> calls take less code than dev_printk(KERN_<LEVEL>
and reducing object size is good.
Coalesce formats for easier grep.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following build failure on S390:
In file included from drivers/net/ethernet/cadence/at91_ether.c:35:0:
drivers/net/ethernet/cadence/macb.h: In function 'macb_is_gem':
drivers/net/ethernet/cadence/macb.h:563:2: error: implicit declaration of function '__raw_readl' [-Werror=implicit-function-declaration]
drivers/net/ethernet/cadence/at91_ether.c: In function 'update_mac_address':
drivers/net/ethernet/cadence/at91_ether.c:119:2: error: implicit declaration of function '__raw_writel' [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware doesn't support controlling pause frames autoneg, so
report that back correctly to userspace.
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use the module_pci_driver macro to make the code simpler
by eliminating module_init and module_exit calls.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use the module_pci_driver macro to make the code simpler
by eliminating the module_init and module_exit calls
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable retval is initialized but never used
otherwise, so remove the unused variable.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the module_pci_driver() macro to make the code simpler
by eliminating module_init and module_exit calls.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the net device ops to manage the embedded
hardware bridge on ixgbe devices. With this patch the bridge
mode can be toggled between VEB and VEPA to support stacking
macvlan devices or using the embedded switch without any SW
component in 802.1Qbg/br environments.
Additionally, this adds source address pruning to the ixgbevf
driver to prune any frames sent back from a reflective relay on
the switch. This is required because the existing hardware does
not support this. Without it frames get pushed into the stack
with its own src mac which is invalid per 802.1Qbg VEPA
definition.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change fixes a sparse warning triggered by us casting the timestamp in
the packet as a u64 instead of as a __le64. This change corrects that in
order to resolve the sparse warning.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are multiple places in our device nvm where the version is stored.
This update fixes some output errors with some types of images and
refactors the way the version data is gathered and stored for ethtool output.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Newer devices supported by igb can support auto-crossover detection in
forced operation modes. Enable this in the driver, rather than clobbering
this functionality in forced operation.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Ignoring the return value from a call to the kernel dma_map API functions
can cause data corruption and system instability. Check the return value
and take appropriate action.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver should not forward LLDP type frames. Inspect the ether type and
do not send if it is an LLDP ethertype frame.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Hw timestamping code caused performance regression in ixgbe driver when the
timestamping is not enabled. The culprit is IXGBE_READ_REG call in the Rx
path which is executed for every received skb. This call is not needed when
the timestamping is disabled or for non-ptp packets.
netperf results:
The ixgbe side of the connection was acting as a server, the netperf command
line on the other side was:
netperf -H 192.168.1.23 -T0,0 -t UDP_STREAM -l 20
The values below mean throughput as reported by netperf (local/remote), for
3 runs, with timestamping not enabled.
3.7.0-rc1+ with CONFIG_IXGBE_PTP off:
5373.83 / 3329.32
5721.88 / 3033.89
5653.42 / 3112.38
3.7.0-rc1+ with CONFIG_IXGBE_PTP on:
5233.64 / 1226.85
5448.67 / 1039.32
5421.36 / 1095.66
Patched 3.7.0-rc1+ with CONFIG_IXGBE_PTP on:
5594.72 / 2942.53
5428.95 / 3110.16
5343.56 / 3200.48
Reported-by: Jesper Brouer <jbrouer@redhat.com>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: Andy Gospodarek <gospo@redhat.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Adds/updates ASCII descriptor maps for 82598 and 82599 Tx/Rx descriptors.
Current descriptor maps were out of date for 82598 and incorrect for
82599.
Signed-off-by: Josh Hay <joshua.a.hay@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that compare the total_rx_packets cleaned to budget
instead of decrementing budget. The advantage to this approach is that budget
can now be const and we only end up modifying total_rx_packets instead of
modifying both it and budget.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When setting a MAC filter for the VF the function should return a success
or failure code, not the index of the new filter. It causes spurious NACK
returns to the VF driver.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch simplifies the check for calling en/disable_tx_laser() function
pointer. The pointer is only set on parts that can use it.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In SR-IOV mode the PF driver acts as the uplink port and is
used to send control packets e.g. lldpad, stp, etc.
eth0.1 eth0.2 eth0
VF VF PF
| | | <-- stand-in for uplink
| | |
--------------------------
| Embedded Switch |
--------------------------
|
MAC <-- uplink
But the embedded switch is setup to forward multicast addresses
to all interfaces both VFs and PF and onto the physical link.
This results in reserved MAC addresses used by control protocols
to be forwarded over the switch onto the VF.
In the LLDP case the PF sends an LLDPDU and it is currently
being forwarded to all the VFs who then see the PF as a peer.
This is incorrect.
This patch adds the multicast addresses to the RAR table in the
hardware to prevent this behavior.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function to set the macvlan filter should return success or failure
instead of the index of the filter. The message processing function was
misinterpreting the index as a non-zero return code indicating failure and
NACKing MAC filter set messages that actually succeeded.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Calling the ixgbe_reset_pipeline_82599 function will ensure a full pipeline
reset on all 82599 devices. This is necessary to avoid possible link issues.
Since this patch accomplishes this by modifying AUTOC.LMS we need to wrap
all AUTOC writes when LESM is enabled.
v2- fix LMS behaviour based on feedback by Martin Josefsson
CC: Martin Josefsson <gandalf@mjufs.se>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull networking fixes from David Miller:
"This is what we usually expect at this stage of the game, lots of
little things, mostly in drivers. With the occasional 'oops didn't
mean to do that' kind of regressions in the core code."
1) Uninitialized data in __ip_vs_get_timeouts(), from Arnd Bergmann
2) Reject invalid ACK sequences in Fast Open sockets, from Jerry Chu.
3) Lost error code on return from _rtl_usb_receive(), from Christian
Lamparter.
4) Fix reset resume on USB rt2x00, from Stanislaw Gruszka.
5) Release resources on error in pch_gbe driver, from Veaceslav Falico.
6) Default hop limit not set correctly in ip6_template_metrics[], fix
from Li RongQing.
7) Gianfar PTP code requests wrong kind of resource during probe, fix
from Wei Yang.
8) Fix VHOST net driver on big-endian, from Michael S Tsirkin.
9) Mallenox driver bug fixes from Jack Morgenstein, Or Gerlitz, Moni
Shoua, Dotan Barak, and Uri Habusha.
10) usbnet leaks memory on TX path, fix from Hemant Kumar.
11) Use socket state test, rather than presence of FIN bit packet, to
determine FIONREAD/SIOCINQ value. Fix from Eric Dumazet.
12) Fix cxgb4 build failure, from Vipul Pandya.
13) Provide a SYN_DATA_ACKED state to complement SYN_FASTOPEN in socket
info dumps. From Yuchung Cheng.
14) Fix leak of security path in kfree_skb_partial(). Fix from Eric
Dumazet.
15) Handle RX FIFO overflows more resiliently in pch_gbe driver, from
Veaceslav Falico.
16) Fix MAINTAINERS file pattern for networking drivers, from Jean
Delvare.
17) Add iPhone5 IDs to IPHETH driver, from Jay Purohit.
18) VLAN device type change restriction is too strict, and should not
trigger for the automatically generated vlan0 device. Fix from Jiri
Pirko.
19) Make PMTU/redirect flushing work properly again in ipv4, from
Steffen Klassert.
20) Fix memory corruptions by using kfree_rcu() in netlink_release().
From Eric Dumazet.
21) More qmi_wwan device IDs, from Bjørn Mork.
22) Fix unintentional change of SNAT/DNAT hooks in generic NAT
infrastructure, from Elison Niven.
23) Fix 3.6.x regression in xt_TEE netfilter module, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (57 commits)
tilegx: fix some issues in the SW TSO support
qmi_wwan/cdc_ether: move Novatel 551 and E362 to qmi_wwan
net: usb: Fix memory leak on Tx data path
net/mlx4_core: Unmap UAR also in the case of error flow
net/mlx4_en: Don't use vlan tag value as an indication for vlan presence
net/mlx4_en: Fix double-release-range in tx-rings
bas_gigaset: fix pre_reset handling
vhost: fix mergeable bufs on BE hosts
gianfar_ptp: use iomem, not ioports resource tree in probe
ipv6: Set default hoplimit as zero.
NET_VENDOR_TI: make available for am33xx as well
pch_gbe: fix error handling in pch_gbe_up()
b43: Fix oops on unload when firmware not found
mwifiex: clean up scan state on error
mwifiex: return -EBUSY if specific scan request cannot be honored
brcmfmac: fix potential NULL dereference
Revert "ath9k_hw: Updated AR9003 tx gain table for 5GHz"
ath9k_htc: Add PID/VID for a Ubiquiti WiFiStation
rt2x00: usb: fix reset resume
rtlwifi: pass rx setup error code to caller
...
- Fix crash in error path in cxgb4
- Fix build error on 32 bits in mlx4
- Fix SR-IOV bugs in mlx4
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=1EJ/
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband fixes from Roland Dreier:
"Small batch of fixes for 3.7:
- Fix crash in error path in cxgb4
- Fix build error on 32 bits in mlx4
- Fix SR-IOV bugs in mlx4"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
mlx4_core: Perform correct resource cleanup if mlx4_QUERY_ADAPTER() fails
mlx4_core: Remove annoying debug messages from SR-IOV flow
RDMA/cxgb4: Don't free chunk that we have failed to allocate
IB/mlx4: Synchronize cleanup of MCGs in MCG paravirtualization
IB/mlx4: Fix QP1 P_Key processing in the Primary Physical Function (PPF)
IB/mlx4: Fix build error on platforms where UL is not 64 bits
This change correctly computes the header length and data length in
the fragments to avoid a bug where we would end up with extremely
slow performance. Also adopt use of skb_frag_size() accessor.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Cc: stable@vger.kernel.org [v3.6]
Signed-off-by: David S. Miller <davem@davemloft.net>
If a failure takes place during the EQ creation, we need to unmap the
UAR memory block too.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Uri Habusha <urih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vlan tag can be zero. This is why it can't serve as an indication
that packet requires VLAN header in the TX flow.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The QP range is reserved as a single block. However, when freeing the
en resources, the tx-ring QPs are released both in mlx4_en_destroy_tx_ring
(one at a time) and in mlx4_en_free_resources (as a block release).
Fix by eliminating the one-at-a-time release in mlx4_en_destroy_tx_ring.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable ALDPS function to save power when link down. Note that the
feature should be set after the other PHY settings. And the firmware
is necessary. Don't enable it without loading the firmware.
None of the firmware-free chipsets support ALDPS. Neither do the
RTL8168d/8111d.
For 8136 series, make sure the ALDPS is disabled before loading the
firmware. For 8168 series, the ALDPS would be disabled automatically
when loading firmware. You must not disable it directly.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using a 36 bit dtb file, the driver complains "resource busy".
Investigating the source of the message leads one to the
gianfar_ptp_probe function.
Since the type of the device resource requested in this function
is IORESOURCE_MEM, it should use "iomem_resource" instead of
"ioports_resource".
Signed-off-by: Wei Yang <Wei.Yang@windriver.com>
Cc: Claudiu Manoil <claudiu.manoil@freescale.com>
Cc: Timur Tabi <timur@freescale.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cpsw/davinci mdio ip cores are present on am33xx, so make NET_VENDOR_TI
visible for it as well.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we fail to allocate rx buffers pool by any reason, we'll just return
with an error, however we've previously successfully requested an irq. Fix
this by releasing the irq before returning the error.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FW flashing code, even though it works correctly, makes some hidden
assumptions about buffer sizes. This is causing code analysers to
report error. Cleanup FW flashing code to remove these hidden assumptions.
Reported-by: Yuanhan Liu <yuanhan.liu@intel.com>
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed the resource cleanup to act correctly and prevent a kernel oops when
mlx4_QUERY_ADAPTER() fails.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
These debug prints left behind by commits c82e9aa0a8 ("mlx4_core:
resource tracking for HCA resources used by guests"), 54679e1482
("mlx4: Implement QP paravirtualization and maintain phys_pkey_cache
for smp_snoop") and 993c401e20 ("mlx4_core: Add IB port-state
machine and port mgmt event propagation") make it pretty hard to
actually use the mlx4_core debug messages when running in SRIOV/IB
mode -- for example, the module load sequence of a device with one VF
yielded 631 debug prints, with 408 of them being from this set. Let's
just remove them.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Ignoring the return value from a call to the kernel dma_map API functions
can cause data corruption and system instability. Check the return value
and take appropriate action.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch updates the igb driver version to 4.0.17.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There was a problem in the initial implementation of the get cable length
function for i210 and it did not work properly. This patch fixes that
problem for i210/i211 devices.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is a HW requirement. Although a buffer as short as 1 byte is allowed,
the total length of packet before, padding and CRC insertion, must be at
least 17 bytes. So pad all small packets manually up to 17 bytes before
delivering them to HW.
Signed-off-by: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
This series contains updates to ixgbe only. Only change to this series
is I dropped the "ixgbe: Add support for pipeline reset" due to
change requested by Martin Josefsson.
Alexander Duyck (7):
ixgbe: Add support for IPv6 and UDP to ixgbe_get_headlen
ixgbe: Add support for tracking the default user priority to SR-IOV
ixgbe: Add support for GET_QUEUES message to get DCB configuration
ixgbe: Enable support for VF API version 1.1 in the PF.
ixgbevf: Add VF DCB + SR-IOV support
ixgbe: Drop unnecessary addition from ixgbe_set_rx_buffer_len
ixgbe: Fix possible memory leak in ixgbe_set_ringparam
Don Skidmore (1):
ixgbe: Add function ixgbe_reset_pipeline_82599
Emil Tantilov (1):
ixgbe: add WOL support for new subdevice id
Jacob Keller (1):
ixgbe: (PTP) refactor init, cyclecounter and reset
Tushar Dave (1):
ixgbe: Correcting small packet padding
Wei Yongjun (1):
ixgbe: using is_zero_ether_addr() to simplify the code
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This will allow us to remove the last mach include from at91_ether
and also make it easier to share address setup with macb.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that HAVE_NET_MACB is gone let's just select MACB to
satisfy the dependecies in at91_ether.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
macb is a platform driver and there is nothing that prevents
this driver from being built on non-ARM/AVR32 platforms.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building macb on x86_64 the following warnings show up:
drivers/net/ethernet/cadence/macb.c: In function macb_interrupt:
drivers/net/ethernet/cadence/macb.c:556:4: warning: large integer implicitly truncated to unsigned type [-Woverflow]
drivers/net/ethernet/cadence/macb.c: In function macb_reset_hw:
drivers/net/ethernet/cadence/macb.c:792:2: warning: large integer implicitly truncated to unsigned type [-Woverflow]
drivers/net/ethernet/cadence/macb.c:793:2: warning: large integer implicitly truncated to unsigned type [-Woverflow]
drivers/net/ethernet/cadence/macb.c:796:2: warning: large integer implicitly truncated to unsigned type [-Woverflow]
Use -1 insted of ~0UL, as done in other places in the driver,
to silence these warnings.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when FIFO_ERR happens, we stop the dma, wait for it to become
idle and then reset the whole MAC_RX logic (and after that we must re-set
multicast addresses and also re-enable MAC_RX when we're finally ready to
accept new packets). This leads to CRC errors on high number of incoming
packets and is not needed according to the datasheet.
This patch fixes it by the following steps:
1) remove this reset in pch_gbe_stop_receive(), which causes some functions
to not be used anywhere
2) remove already unused functions pch_gbe_wait_clr_bit_irq() and
pch_gbe_mac_reset_rx() to correctly build
3) move pch_gbe_enable_mac_rx() out of pch_gbe_start_receive() to
pch_gbe_up() where it's only needed after we've removed the MAC_RX reset
4) rename pch_gbe_start/stop_receive() to pch_gbe_enable/disable_dma_rx()
to more precisely reflect what the functions are now doing.
After these changes we already don't see the CRC errors and gain some
increase in RX processing speed.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
