The osdc parameter to ceph_calc_raw_layout() is not used, so get rid
of it. Consequently, the corresponding parameter in calc_layout()
becomes unused, so get rid of that as well.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
A snapshot id must be provided to ceph_calc_raw_layout() even though
it is not needed at all for calculating the layout.
Where the snapshot id *is* needed is when building the request
message for an osd operation.
Drop the snapid parameter from ceph_calc_raw_layout() and pass
that value instead in ceph_osdc_build_request().
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
The len argument to ceph_osdc_build_request() is set up to be
passed by address, but that function never updates its value
so there's no need to do this. Tighten up the interface by
passing the length directly.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
For some reason, the snapid field of the osd request header is
explicitly set to CEPH_NOSNAP in rbd_do_request(). Just a few lines
later--with no code that would access this field in between--a call
is made to ceph_calc_raw_layout() passing the snapid provided to
rbd_do_request(), which encodes the snapid value it is provided into
that field instead.
In other words, there is no need to fill in CEPH_NOSNAP, and doing
so suggests it might be necessary. Don't do that any more.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
The snapc and snapid parameters to rbd_req_sync_op() always take
the values NULL and CEPH_NOSNAP, respectively. So just get rid
of them and use those values where needed.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
All callers of rbd_req_sync_exec() pass CEPH_OSD_FLAG_READ as their
flags argument. Delete that parameter and use CEPH_OSD_FLAG_READ
within the function. If we find a need to support write operations
we can add it back again.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
There is only one caller of rbd_req_sync_read(), and it passes
CEPH_NOSNAP as the snapshot id argument. Delete that parameter
and just use CEPH_NOSNAP within the function.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
The last two parameters to ceph_osd_build_request() describe the
object id, but the values passed always come from the osd request
structure whose address is also provided. Get rid of those last
two parameters.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Pull a block of code that initializes the layout structure in an osd
request into its own function so it can be reused.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Dan Mick <dan.mick@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Right now we get the snapshot context for an rbd image (under
protection of the header semaphore) for every request processed.
There's no need to get the snap context if we're doing a read,
so avoid doing so in that case.
Note that we no longer need to hold the header semaphore to
check the rbd_dev's existence flag.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
The rbd_device->exists field can be updated asynchronously, changing
from set to clear if a mapped snapshot disappears from the base
image's snapshot context.
Currently, value of the "exists" flag is only read and modified
under protection of the header semaphore, but that will change with
the next patch. Making it atomic ensures this won't be a problem
because the a the non-existence of device will be immediately known.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Now that a big hunk in the middle of rbd_rq_fn() has been moved
into its own routine we can simplify it a little more.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Only one of the three callers of rbd_do_request() provide a
collection structure to aggregate status.
If an error occurs in rbd_do_request(), have the caller
take care of calling rbd_coll_end_req() if necessary in
that one spot.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
In rbd_rq_fn(), requests are fetched from the block layer and each
request is processed, looping through the request's list of bio's
until they've all been consumed.
Separate the handling for a single request into its own function to
make it a bit easier to see what's going on.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
The result field in a ceph osd reply header is a signed 32-bit type,
but rbd code often casually uses int to represent it.
The following changes the types of variables that handle this result
value to be "s32" instead of "int" to be completely explicit about
it. Only at the point we pass that result to __blk_end_request()
does the type get converted to the plain old int defined for that
interface.
There is almost certainly no binary impact of this change, but I
prefer to show the exact size and signedness of the value since we
know it.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Dan Mick <dan.mick@inktank.com>
There are spots where a ceph_osds_request pointer variable is given
the name "req". Since we're dealing with (at least) three types of
requests (block layer, rbd, and osd), I find this slightly
distracting.
Change such instances to use "osd_req" consistently to make the
abstraction represented a little more obvious.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Dan Mick <dan.mick@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
There are two names used for items of rbd_request structure type:
"req" and "req_data". The former name is also used to represent
items of pointers to struct ceph_osd_request.
Change all variables that have these names so they are instead
called "rbd_req" consistently.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Dan Mick <dan.mick@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Josh suggested adding warnings to this function to help users
diagnose problems.
Other than memory allocatino errors, there are two places where
errors can be returned. Both represent problems that should
have been caught earlier, and as such might well have been
handled with BUG_ON() calls. But if either ever did manage to
happen, it will be reported.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Add a warning in bio_chain_clone_range() to help a user determine
what exactly might have led to a failure. There is only one; please
say something if you disagree with the following reasoning.
There are three places this can return abnormally:
- Initially, if there is nothing to clone. It turns out that
right now this cannot happen anyway. The test is in place
because the code below it doesn't work if those conditions
don't hold. As such they could be assertions but since I can
return a null to indicate an error I just do that instead.
I have not added a warning here because it won't happen.
- While processing bio's, if none remain but there are supposed
to be more bytes to clone. Here I have added a warning.
- If bio_clone_range() returns a null pointer. That function
will have already produced a warning (at least the first
time, via WARN_ON_ONCE()) to distinguish the cause of the
error. The only exception is memory exhaustion, and I'd
rather not pepper the code with warnings in all those spots.
So no warning is added in that place.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Tell the user (via dmesg) what was wrong with the arguments provided
via /sys/bus/rbd/add.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Dan Mick <dan.mick@inktank.com>
Define a new function rbd_warn() that produces a boilerplate warning
message, identifying in the resulting message the affected rbd
device in the best way available. Use it in a few places that now
use pr_warning().
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Dan Mick <dan.mick@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
This replaces two kmalloc()/memcpy() combinations with a single
call to kmemdup().
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: David Zafman <david.zafman@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
There is no real benefit to keeping the length of an image id, so
get rid of it.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: David Zafman <david.zafman@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
There may have been a benefit to hanging on to the length of an
image name before, but there is really none now. The only time it's
used is when probing for rbd images, so we can just compute the
length then.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: David Zafman <david.zafman@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
I promised Josh I would document whether there were any restrictions
needed for accessing fields of an rbd_spec structure. This adds a
big block of comments that documents the structure and how it is
used--including the fact that we don't attempt to synchronize access
to it.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: David Zafman <david.zafman@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Hi Asai,
FYI, there are new sparse warnings show up in
tree: git://git.kernel.dk/linux-block.git for-3.9/drivers
head: 3d6a87430e
commit: 152834694d [2/3] mtip32xx: add trim support
>> drivers/block/mtip32xx/mtip32xx.c:1726:5: sparse: symbol 'mtip_send_trim' was not declared. Should it be static?
drivers/block/mtip32xx/mtip32xx.c:3348:17: sparse: cast to restricted __le32
drivers/block/mtip32xx/mtip32xx.c:4125:1: sparse: symbol 'mtip_workq_sdbf0' was not declared. Should it be static?
drivers/block/mtip32xx/mtip32xx.c:4126:1: sparse: symbol 'mtip_workq_sdbf1' was not declared. Should it be static?
drivers/block/mtip32xx/mtip32xx.c:4127:1: sparse: symbol 'mtip_workq_sdbf2' was not declared. Should it be static?
drivers/block/mtip32xx/mtip32xx.c:4128:1: sparse: symbol 'mtip_workq_sdbf3' was not declared. Should it be static?
drivers/block/mtip32xx/mtip32xx.c:4129:1: sparse: symbol 'mtip_workq_sdbf4' was not declared. Should it be static?
drivers/block/mtip32xx/mtip32xx.c:4130:1: sparse: symbol 'mtip_workq_sdbf5' was not declared. Should it be static?
drivers/block/mtip32xx/mtip32xx.c:4131:1: sparse: symbol 'mtip_workq_sdbf6' was not declared. Should it be static?
drivers/block/mtip32xx/mtip32xx.c:4132:1: sparse: symbol 'mtip_workq_sdbf7' was not declared. Should it be static?
drivers/block/mtip32xx/mtip32xx.c: In function 'mtip_hw_read_flags':
drivers/block/mtip32xx/mtip32xx.c:2804:1: warning: the frame size of 1036 bytes is larger than 1024 bytes [-Wframe-larger-than=]
drivers/block/mtip32xx/mtip32xx.c: In function 'mtip_hw_read_registers':
drivers/block/mtip32xx/mtip32xx.c:2781:1: warning: the frame size of 1044 bytes is larger than 1024 bytes [-Wframe-larger-than=]
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Hi Asai,
FYI, there are new sparse warnings show up in
tree: git://git.kernel.dk/linux-block.git for-3.9/drivers
head: 3d6a87430e
commit: 16c906e51c [1/3] mtip32xx: Add workqueue and NUMA support
drivers/block/mtip32xx/mtip32xx.c:3267:17: sparse: cast to restricted __le32
>> drivers/block/mtip32xx/mtip32xx.c:4029:1: sparse: symbol 'mtip_workq_sdbf0' was not declared. Should it be static?
>> drivers/block/mtip32xx/mtip32xx.c:4030:1: sparse: symbol 'mtip_workq_sdbf1' was not declared. Should it be static?
>> drivers/block/mtip32xx/mtip32xx.c:4031:1: sparse: symbol 'mtip_workq_sdbf2' was not declared. Should it be static?
>> drivers/block/mtip32xx/mtip32xx.c:4032:1: sparse: symbol 'mtip_workq_sdbf3' was not declared. Should it be static?
>> drivers/block/mtip32xx/mtip32xx.c:4033:1: sparse: symbol 'mtip_workq_sdbf4' was not declared. Should it be static?
>> drivers/block/mtip32xx/mtip32xx.c:4034:1: sparse: symbol 'mtip_workq_sdbf5' was not declared. Should it be static?
>> drivers/block/mtip32xx/mtip32xx.c:4035:1: sparse: symbol 'mtip_workq_sdbf6' was not declared. Should it be static?
>> drivers/block/mtip32xx/mtip32xx.c:4036:1: sparse: symbol 'mtip_workq_sdbf7' was not declared. Should it be static?
drivers/block/mtip32xx/mtip32xx.c: In function 'mtip_hw_read_flags':
drivers/block/mtip32xx/mtip32xx.c:2723:1: warning: the frame size of 1036 bytes is larger than 1024 bytes [-Wframe-larger-than=]
drivers/block/mtip32xx/mtip32xx.c: In function 'mtip_hw_read_registers':
drivers/block/mtip32xx/mtip32xx.c:2700:1: warning: the frame size of 1044 bytes is larger than 1024 bytes [-Wframe-larger-than=]
Please consider folding the below diff :-)
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There is a missing break statement here. This used to return directly
but we re-worked it in 2008 to add locking as part of the BKL push down.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
TRIM support added through vendor unique command.
Signed-off-by: Sam Bradshaw < sbradshaw@micron.com>
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch contains
* parallel command completion using workers
* bind the workers to the chosen numa node
* bind isr to the chosen numa node
* allocating memory in the chosen numa node
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Sam Bradshaw <sbradshaw@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When rebuild is in progress, disk->queue is yet to be created. Surprise
removing the device will call remove()-> del_gendisk(). del_gendisk()
expect disk->queue be not NULL. Fix is to call put_disk() when disk_queue
is NULL.
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If an I/O command times out when a PIO command is active,
MTIP_PF_EH_ACTIVE_BIT is not cleared. This results in I/O
hang in the driver. Fix is to clear this bit.
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This driver was for the 8 bit ISA cards that were installed in
the PC-XT machines of 1980 vintage. They supported the dual
ribbon cable MFM drives of 10-20MB capacity, and ran at a 3:1
interleave, giving performance on the order of 128kB/s.
By the introduction of the PC-AT (286) these controllers were
already scrapped in favour of 16 bit controllers with some onboard
RAM that could support a 1:1 interleave.
The git history doesn't show any evidence of runtime fixes that
would reflect active usage; instead just the usual tree-wide API
type changes/cleanups. Going back to in-source changelogs, the
last "runtime" fix that is evident is something I did over a
dozen years ago[1] -- and even back then, the hardware was long
since unavailable, so that ancient fix was also not runtime tested.
The time is long overdue for this to get flushed, so lets get
rid of it before anyone wastes more time doing builds and sparse
checks etc. on long since dead code.
[1] http://lkml.indiana.edu/hypermail/linux/kernel/0102.2/0027.html
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Mike Miller <mike.miller@hp.com>
Cc: Chirag Kantharia <chirag.kantharia@hp.com>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Jim Paris <jim@jtan.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Matthew Wilcox <matthew.r.wilcox@intel.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: NeilBrown <neilb@suse.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Tao Guo <Tao.Guo@emc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a file system is mounted on a virtio-blk disk, we then remove it
and then reattach it, the reattached disk gets the same disk name and
ids as the hot removed one.
This leads to very nasty effects - mostly rendering the newly attached
device completely unusable.
Trying what happens when I do the same thing with a USB device, I saw
that the sd node simply doesn't get free'd when a device gets forcefully
removed.
Imitate the same behavior for vd devices. This way broken vd devices
simply are never free'd and newly attached ones keep working just fine.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org
Pull Ceph update from Sage Weil:
"There are a few different groups of commits here. The largest is
Alex's ongoing work to enable the coming RBD features (cloning,
striping). There is some cleanup in libceph that goes along with it.
Cyril and David have fixed some problems with NFS reexport (leaking
dentries and page locks), and there is a batch of patches from Yan
fixing problems with the fs client when running against a clustered
MDS. There are a few bug fixes mixed in for good measure, many of
which will be going to the stable trees once they're upstream.
My apologies for the late pull. There is still a gremlin in the rbd
map/unmap code and I was hoping to include the fix for that as well,
but we haven't been able to confirm the fix is correct yet; I'll send
that in a separate pull once it's nailed down."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (68 commits)
rbd: get rid of rbd_{get,put}_dev()
libceph: register request before unregister linger
libceph: don't use rb_init_node() in ceph_osdc_alloc_request()
libceph: init event->node in ceph_osdc_create_event()
libceph: init osd->o_node in create_osd()
libceph: report connection fault with warning
libceph: socket can close in any connection state
rbd: don't use ENOTSUPP
rbd: remove linger unconditionally
rbd: get rid of RBD_MAX_SEG_NAME_LEN
libceph: avoid using freed osd in __kick_osd_requests()
ceph: don't reference req after put
rbd: do not allow remove of mounted-on image
libceph: Unlock unprocessed pages in start_read() error path
ceph: call handle_cap_grant() for cap import message
ceph: Fix __ceph_do_pending_vmtruncate
ceph: Don't add dirty inode to dirty list if caps is in migration
ceph: Fix infinite loop in __wake_requests
ceph: Don't update i_max_size when handling non-auth cap
bdi_register: add __printf verification, fix arg mismatch
...
The functions rbd_get_dev() and rbd_put_dev() are trivial wrappers
that add no value, and their existence suggests they may do more
than what they do.
Get rid of them.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Dan Mick <dan.mick@inktank.com>
Konrad writes:
Please git pull the following branch:
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen.git stable/for-jens-3.8
which has a bug-fix to the xen-blkfront and xen-blkback driver
when using the persistent mode. An issue was discovered where LVM
disks could not be read correctly and this fixes it. There
is also a change in llist.h which has been blessed by akpm.
Merge misc patches from Andrew Morton:
"Incoming:
- lots of misc stuff
- backlight tree updates
- lib/ updates
- Oleg's percpu-rwsem changes
- checkpatch
- rtc
- aoe
- more checkpoint/restart support
I still have a pile of MM stuff pending - Pekka should be merging
later today after which that is good to go. A number of other things
are twiddling thumbs awaiting maintainer merges."
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (180 commits)
scatterlist: don't BUG when we can trivially return a proper error.
docs: update documentation about /proc/<pid>/fdinfo/<fd> fanotify output
fs, fanotify: add @mflags field to fanotify output
docs: add documentation about /proc/<pid>/fdinfo/<fd> output
fs, notify: add procfs fdinfo helper
fs, exportfs: add exportfs_encode_inode_fh() helper
fs, exportfs: escape nil dereference if no s_export_op present
fs, epoll: add procfs fdinfo helper
fs, eventfd: add procfs fdinfo helper
procfs: add ability to plug in auxiliary fdinfo providers
tools/testing/selftests/kcmp/kcmp_test.c: print reason for failure in kcmp_test
breakpoint selftests: print failure status instead of cause make error
kcmp selftests: print fail status instead of cause make error
kcmp selftests: make run_tests fix
mem-hotplug selftests: print failure status instead of cause make error
cpu-hotplug selftests: print failure status instead of cause make error
mqueue selftests: print failure status instead of cause make error
vm selftests: print failure status instead of cause make error
ubifs: use prandom_bytes
mtd: nandsim: use prandom_bytes
...
Currently blkfront fails to handle cases in blkif_completion like the
following:
1st loop in rq_for_each_segment
* bv_offset: 3584
* bv_len: 512
* offset += bv_len
* i: 0
2nd loop:
* bv_offset: 0
* bv_len: 512
* i: 0
In the second loop i should be 1, since we assume we only wanted to
read a part of the previous page. This patches fixes this cases where
only a part of the shared page is read, and blkif_completion assumes
that if the bv_offset of a bvec is less than the previous bv_offset
plus the bv_size we have to switch to the next shared page.
Reported-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Cc: linux-kernel@vger.kernel.org
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Implement a safe version of llist_for_each_entry, and use it in
blkif_free. Previously grants where freed while iterating the list,
which lead to dereferences when trying to fetch the next item.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
[v2: Move the llist_for_each_entry_safe in llist.h]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
We should return NULL on failure instead of returning a freed pointer.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This version number is printed to the console on module initialization
and is available in sysfs, which is where the userland aoe-version tool
looks for it.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This change only affects experimental AoE storage networks.
It modifies the console message about runt packets detected so that the
AoE major and minor addresses of the AoE target that generated the runt
are mentioned.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
By default, the aoe driver uses any ethernet interface for AoE, but the
aoe_iflist module parameter provides a convenient way to limit AoE
traffic to a specific list of local network interfaces.
This change allows a list to be specified using the comma character as a
separator. For example,
modprobe aoe aoe_iflist=eth2,eth3
Before, it was inconvenient to get the quoting right in shell scripts
when setting aoe_iflist to have more than one network interface.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With this change, the aoe driver treats the value zero as special for
the aoe_deadsecs module parameter. Normally, this value specifies the
number of seconds during which the driver will continue to attempt
retransmits to an unresponsive AoE target. After aoe_deadsecs has
elapsed, the aoe driver marks the aoe device as "down" and fails all
I/O.
The new meaning of an aoe_deadsecs of zero is for the driver to
retransmit commands indefinitely.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many AoE targets have four or fewer network ports, but some existing
storage devices have many, and the AoE protocol sets no limit.
This patch allows the use of more than eight remote MAC addresses per AoE
target, while reducing the amount of memory used by the aoe driver in
cases where there are many AoE targets with fewer than eight MAC addresses
each.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This change avoids a race that could result in a NULL pointer derference
following a WARNing from kobject_add_internal, "don't try to register
things with the same name in the same directory."
The problem was found with a test that forgets and discovers an
aoe device in a loop:
while test ! -r /tmp/stop; do
aoe-flush -a
aoe-discover
done
The race was between aoedev_flush taking aoedevs out of the devlist,
allowing a new discovery of the same AoE target to take place before the
driver gets around to calling sysfs_remove_group. Fixing that one
revealed another race between do_open and add_disk, and this patch avoids
that, too.
The fix required some care, because for flushing (forgetting) an aoedev,
some of the steps must be performed under lock and some must be able to
sleep. Also, for discovering a new aoedev, some steps might sleep.
The check for a bad aoedev pointer remains from a time when about half of
this patch was done, and it was possible for the
bdev->bd_disk->private_data to become corrupted. The check should be
removed eventually, but it is not expected to add significant overhead,
occurring in the aoeblk_open routine.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
An AoE target can have multiple network ports used for AoE, and in the
aoe driver, those are tracked by the aoetgt struct. These changes allow
the aoe driver to handle network paths, or aoetgts, that are not working
well, compared to the others.
Paths that do not get responses despite the retransmission of AoE
commands are marked as "tainted", and non-tainted paths are preferred.
Meanwhile, the aoe driver attempts to "probe" the tainted path in the
background by issuing reads of LBA 0 that are padded out to full
(possibly jumbo-frame) size. If the probes get responses, then the path
is "redeemed", and its taint is removed.
This mechanism has been shown to be helpful in transparently handling
and recovering from real-world network "brown outs" in ways that the
earlier "shoot the help-needing target in the head" mechanism could not.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The value returned by the static minor device number number allocator is
the real minor number, so it must be multiplied by the supported number
of partitions per aoedev.
Without this fix the support for systems without udev is incomplete, and
the few users of aoe on such systems will have surprising results when
device nodes names do not match the AoE target.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
