Update operating-points per hardware document and add support for
1 GHz and 1.2 GHz frequencies.
400 MHz, 800 MHz and 1 GHz should be supported by all i.MX6Q chips,
while 1.2 GHz support needs to know from OTP fuse bit.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This mxs usbphy is only needs to be on after system boots
up, and software never needs to control it anymore.
Meanwhile, usbphy's parent needs to be notified if usb
is suspend or not. So we design below mxs usbphy usage:
- usbphy1_gate and usbphy2_gate:
Their parents are dummy clock, we only needs to enable
it after system boots up.
- usbphy1 and usbphy2
Usage reserved bit for this clock, in that case, the refcount
will be updated, but without hardware changing.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Remove silicon version from SDMA firmware.
This makes it consistent with other i.MX SoCs firmware names.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The MBa53 is a baseboard for the TQMA53 embedded module. This enables/adds only
supported devices, i.e. it is not feature complete, because of missing drivers
in mainline linux.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The tqma53 is an embedded module that has some features on board (e.g. emmc),
but mostly just provides access to them on its interface.
Going along with the imx53.dtsi, the tqma53.dtsi specifies the existing
devices and their pinctrl for this module. All devices that are not on the
module are disabled by default and need to be enabled in a baseboard DT.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add pinctrl for cspi, csi.
Add new pingroups for can1 and uart3.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The keypad is on the accessory board of i.MX51 babbage
main board and is driven by Keypad Port(KPP) in SoC.
The keymap is the same to i.MX25 3stack platform as
the accessory board schematic tells that it is designed
in this way.
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Just to keep consistency with other dts files, place 'status' entry as the last
one.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Following omap3-evm.dts way, it changes all imx dts files to use label
in board dts to refer to nodes defined by soc dtsi. Thus, the board
dts files become easier to read and edit with the least indentation
levels.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add missing imx dtb targets, so that make dtbs can cover all imx dtbs.
It's pretty useful for testing dts changes.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add an entry for imx27-pdk.dtb, so that it can be generated by default.
Also, add an entry into Documentation/devicetree/bindings/arm/fsl.txt.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
imx27-pdk is the name found on Freescale website, so use it instead of 3ds.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Any devices wishing to use the AB8500's GPIO IRQs were forced to
request virtual IRQs from the gpio-ab8500 driver. Now that
responsibility has been passed back to the AB8500 core driver,
devices can request real IRQ numbers instead. This patch removes
any traces of the old virtual IRQ conversion handlers, which will
force any drivers requesting IRQs to use real IRQS.
Cc: arm@kernel.org
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
AB8500 GPIO no longer handles its GPIO IRQs. Instead, the AB8500
core driver has taken back the responsibility. Prior to this
happening, the AB8500 GPIO driver provided a set of virtual IRQs
which were used as a pass-through. These virtual IRQs had a base
of MOP500_AB8500_VIR_GPIO_IRQ_BASE, which was passed though pdata.
We don't need to do this anymore, so we're pulling out the
property from the structure.
Cc: arm@kernel.org
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-Compile fix for !SMP
-More cpu cluster id related fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRDSkpAAoJEMhvYp4jgsXiSWYH/jy92oAHpKoNBZQ0wzOVXoa7
Lo9vkPaTexXY1SLNohrTiGDxWwm7LNfi6Lag3OtzyzAblcUAqd6ISyx2Nh7xN3Uu
L+3Y7CIBw9CqCAsrjOunMmKcawo/aiscAlhqOoYsmKGcbopQHEomui+yfDIX6NY+
v59xDXp1IyJHqDc9M3t2VJijfeCHnREIddt33gUeEcSfL7nyuvGf2DXuarAGN5N7
bHd7NxqZS2TNGxTbxuNZIlYuVUgqcVV16LLNlTGrBb27iiPJuIg3uHa6GVVO4n0U
czd388xl5Rca8LeD7rAvWPiHX2rIfyEyvWZO4KvRBC9H6+VgGvlyKtnoUPyNhn8=
=mUYd
-----END PGP SIGNATURE-----
Merge tag 'highbank-fixes-for-3.8' of git://sources.calxeda.com/kernel/linux into fixes
From Rob Herring:
highbank fixes for 3.8
-Compile fix for !SMP
-More cpu cluster id related fixes
* tag 'highbank-fixes-for-3.8' of git://sources.calxeda.com/kernel/linux:
ARM: highbank: mask cluster id from cpu_logical_map
ARM: scu: mask cluster id from cpu_logical_map
ARM: scu: add empty scu_enable for !CONFIG_SMP
Looks like there are few more places that I missed that can cause
compiler warnings. After grepping for omap initcall, all files
needing soc.h should now have it.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
I needed this when compiling for pandaboard.
The reason this is needed is that we are now using
omap_initcalls to keep them multiplatform safe.
Signed-off-by: André Hentschel <nerv@dawncrow.de>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
- Mostly cfa100xx related device tree source updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJREKBFAAoJEFBXWFqHsHzOdVwH/2x2a0mJi9Y/mE0y5ZSn/Ktj
bYIOJt4wjq15/rYcSzCrZtJ+u4+JwP7C06z0oTtNeiIw2kHuAiUTVrTBdaf60k4f
2FauaoX9koedCsBP2JPVAq5ZVE8BdAbj4inuoNUFJeN/pkH8Q5+PWQZbgxAYeN58
X//DUXPq8L2tNWdEl/F+DIYwH/y9ck01tV2Fyy6AItjEShStOCglootmmtzXoyj0
/8bOmc2ppdePofAd+M/5B+JE5S18WbakrdfNp8qVwBlYzjsUvFgz9Vwkbn81jPzJ
5Hx/vDiZFktqMuI6726DJ/oqxP0w+GqYzw657LdIKqS3zCbLGb752iaM/vPgo0c=
=SM0I
-----END PGP SIGNATURE-----
Merge tag 'mxs-dt-3.9' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/dt
From Shawn Guo:
mxs device tree changes for 3.9
- Mostly cfa100xx related device tree source updates
* tag 'mxs-dt-3.9' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: mxs: dts: Add rotary encoder to the CFA-10049
ARM: mxs: dts: Add gpio-keys for the rotary to the CFA-10049
ARM: dts: mxs: Add the LCD to the 10049 board
ARM: dts: mxs: Add muxing options for the third PWM
ARM: dts: cfa10049: Change the SPI3 bus to spi-gpio
ARM: mxs: dt: Add Crystalfontz CFA-10037 device tree support
ARM: mxs: Enable touchscreen on m28evk
ARM: dts: cfa10049: Add PCA9555 GPIO expander to the device tree
- A couple of optimization on timer
- Some updates on mxs_defconfig
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJREJ4lAAoJEFBXWFqHsHzO5bwIAJkZC1IZ+GEh3n9ogbl/JwfE
B0k7xsTrx7TgsXvdX1oxrivu75rxWfhwVgZdp9dO3zEnyeOjFRitnlyfaliKx1JM
8ZHHsVP/VxOTvw5HarirmFejyWr9x+xx1H2p9swDHT+kccUA6aazEykEx4HFAADg
9c7Z3QWVLugwo950ayMgWk6QeRJb6pZj02OlszMiW4t/qphDhoF4qiqR9QiVL1aP
Td655hZzuoCuHrjyrRxUTgTwp70ntzxvwEDCaEqwGhmzN7tqJbi/wXTCcTg8A11A
2u3P8UvqeYKbATeqMP8vl/Ne6E1kAy8sGVTsAFoaooUUtZoN2YMdsIIXiw+JKy4=
=Veye
-----END PGP SIGNATURE-----
Merge tag 'mxs-soc-3.9' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/soc
From Shawn Guo:
mxs soc changes for 3.9
- A couple of optimization on timer
- Some updates on mxs_defconfig
* tag 'mxs-soc-3.9' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: mxs_defconfig: Select CONFIG_DEVTMPFS_MOUNT
ARM: mxs: decrease mxs_clockevent_device.min_delta_ns to 2 clock cycles
ARM: mxs: use apbx bus clock to drive the timers on timrotv2
ARM: mxs: Update mxs_defconfig
The Kconfig options selected by ARCH_TEGRA_*_SOC were recently sorted.
Update the newly added ARCH_TEGRA_114_SOC's select statements to match.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
CONFIG_ARCH_TEGRA_114_SOC doesn't currently enable gpiolib, which causes
numerous build problems building a Tegra kernel with only Tegra114
enabled, and not Tegra20 or Tegra30. Enable ARCH_REQUIRE_GPIOLIB to
solve this. However, all Tegra will use gpiolib, so select this option
from ARCH_TEGRA rather than each individual ARCH_TEGRA_*_SOC, to
prevent this problem for any future chips.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch fixes the build error when ARCH_TEGRA_114_SOC is enabled
and ARCH_TEGRA_3x_SOC is disabled.
This provides Tegra114 with its own tegra114_init_early() instead of
making use of tegra30_init_early() so that T114 build doesn't depend
on T3x anymore.
Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This pull request adds support for I2C0 and watchdog timer
for DA850 EVM booting using device tree. It also enables
machine reboot when using device tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iQIcBAABAgAGBQJRFoKmAAoJEGFBu2jqvgRN0PMP/jRz7la56By25SrTx0mf8RLt
MY8KqLEipoVSATEv5W/SzE7Py1PKQXKFERU6JB14/JwU/+68NfPYfWcRPJ5Ya7/a
vDM7QTSllOjAPRFjpviUD4E5PRz7HV6odYb9l/lKMXhAV7+0X/I14T6k4gEd/3pw
TdhcLRQpPyCr8HKBfnw3n0fHtWo5Zt5J7wze66vL13CIHtPaoIAY7UUN/KggSum6
mHZ3G/Po+iQjkaRyTl0O/sTTkNA3CCp9bVb7v0DXHs6Im283jdVaPX9s5HsuN7Jw
mzs3VTtS1E7is/WJbywy8ry2pjMJozJdRDWYse7wDGzTgCteQsJrQ3+C1H68IvPN
+Phb4NZhrU8clnYtMvCIENiUsK7jNrRbzDPEGLEQa/Z5apqHLFbtWa/Qx88aqALg
QdQsMgG92ZThIJ+LNaLj4fvHH9xnJjYBvYMiaKSwiTWs0b+zILQG+9Dfo8eFpQj+
PgXIhYW5Cg7CP3AqVyS6E2VSV36HCo0pSZ6aaBW6wvoCXDkOEHbxi0NpgvCWCIXK
svKGDbrSqsHnnAJz8xfeuuqpU30YqOAtScfdjfdSTUXVyOSzRD5Tb0bCK4YCpyqm
gCFWRx9y3BlP7AT4RYKKH+JJgkUEmAX7MO0EOIwk9FzxapE3dbNAcV51NoffAILl
M/jfDPHuPZLiG3zBfa+0
=d1si
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v3.9/dt-2' of git://gitorious.org/linux-davinci/linux-davinci into next/dt
From Sekhar Nori:
Second round of DT updates for DaVinci.
This pull request adds support for I2C0 and watchdog timer
for DA850 EVM booting using device tree. It also enables
machine reboot when using device tree.
* tag 'davinci-for-v3.9/dt-2' of git://gitorious.org/linux-davinci/linux-davinci:
ARM: davinci: da850 DT: add support for machine reboot
ARM: davinci: da850: add wdt DT node
ARM: davinci: da850: add DT node for I2C0
- adding the watchdog to Animeo IP board
- some more DT support for at91rm9200 peripherals
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRE8zDAAoJEAf03oE53VmQOXIH/0btL+h2tiV6lY4he090YLTL
SNBbs1m05SvtfMfei1P9sFKokc5IEbf36izd1E30hcLw1bcsUulS9CChyXu4KEc2
Xd6LLIOyH4jLl2/s0rZz1lhxCoFIv9bFp0xaZgtuasUxxlsV5Kg9iee4jYIeHL4G
cX+z8qLgTpL77Ep6HBzc2K1ALXqW/0sjo+5eHwUJDHiM/+awPD3lJMnJjDKLdY8j
0BoODOuHFGTo3fdIeEprJhPTiqZMEFDfOPsLYA2ksPqZEw5LV+ITAnHiw8V5LbBI
XNP8gYTUWLv3LJqnKc9qt/6KjHUsztbtcjsSdOGmZp5IbFQw9AJGg/mBBTpEvJM=
=6yzB
-----END PGP SIGNATURE-----
Merge tag 'at91-dt' of git://github.com/at91linux/linux-at91 into next/dt
From Nicolas Ferre:
Update to DT files for AT91:
- adding the watchdog to Animeo IP board
- some more DT support for at91rm9200 peripherals
* tag 'at91-dt' of git://github.com/at91linux/linux-at91:
ARM: at91: add EMAC bindings to RM9200 DT
ARM: at91: add SSC bindings to RM9200 DT
ARM: at91: add MMC bindings to RM9200 DT
ARM: at91: Animeo IP: enable watchdog support
Signed-off-by: Olof Johansson <olof@lixom.net>
Update for audio support via omap-twl4030 and pwm updates in board level,
and zoom-peripherals update to not request the TWL GPIO7.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=pDtV
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.9/twl-signed-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/boards
From Tony Lidgren:
OMAP TWL updates from Peter Ujfalusi <peter.ujfalusi@ti.com>:
Update for audio support via omap-twl4030 and pwm updates in board level,
and zoom-peripherals update to not request the TWL GPIO7.
* tag 'omap-for-v3.9/twl-signed-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix twl section warnings related to omap_twl4030_audio_init
ARM: board-zoom: Do not request LCD panel enable GPIO from twl4030
ARM: OMAP: omap3beagle: Use the pwm_leds driver to control the PMU_STAT led
ARM: OMAP: board-4430sdp: Proper support for TWL6030 PWM LED/Backlight
ARM: OMAP: sdp3430: Audio support via the common omap-twl4030 machine driver
ARM: OMAP: zoom: Audio support via the common omap-twl4030 machine driver
ARM: OMAP2+: twl-common: Allow boards to customize the twl4030 audio setup
ARM: OMAP2+: twl-common: Add default twl4030 audio configuration
ARM: OMAP: zoom: Zoom2 does not have extmute functionality
ARM: OMAP: 3430sdp: Enable extmute functionality for audio
Register ARM architected timer.
This is preparatory work by Magnus Damm for SoC(s) that use
the ARM architected timer.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Wq1K
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc4-for-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
From Simon Horman:
Fourth round of Renesas ARM-based SoC changes for v3.9
Register ARM architected timer.
This is preparatory work by Magnus Damm for SoC(s) that use
the ARM architected timer.
* tag 'renesas-soc4-for-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Register ARM architected timer
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRFRkcAAoJEAf03oE53VmQ71EH/08SOBM+kgQjKCzFe9ekuytz
DlnUzFWOQlSibjWOL7ruWoLPiTurJHQNiKEpePw7g3dh8ars7fJLlVIr0yRehHBs
pJpxzH7/ZqHqzi+4YXCrn5XAVK9ej7HKFo9zoDD1GMctsOD2FoNDIzOIh47s3z4Y
G92kvGFG5z8EACvcob/+q53RcVjimugcrKRhz61MhKdpiIGGzz/+wl45StyM8RYc
mLFb7yGa1j9Zdstm/45a+3XwMUEbxsbi0NGeA9E9kL3XZZERWkfcDL4MiV3F0l6Q
oJqVQ6/QzGyqnTolr+2FAVkaXDP4geo6S42N97pGIjtIco2gaQ5kbMPoyei98N0=
=SVnr
-----END PGP SIGNATURE-----
Merge tag 'at91-cleanup' of git://github.com/at91linux/linux-at91 into next/cleanup
From Nicolas Ferre:
Little AT91 cleanup: only remove one deprecated board.
* tag 'at91-cleanup' of git://github.com/at91linux/linux-at91:
ARM: at91: remove NEOCORE 926 board
Signed-off-by: Olof Johansson <olof@lixom.net>
Modify/remove conflict in arch/arm/mach-at91/board-neocore926.c
When running on Integrator/AP using atags, ap_syscon_base is initialised
in ->map_io, which isn't called for !MMU platforms.
Instead, initialise the pointer in ->machine_init, as we do when booting
with device-tree.
Cc: stable@vger.kernel.org
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Update the da8xx_restart() function to support machine reboot
when booting using DT. Have the function search for the watchdog
platform device instead of always using "da8xx_wdt_device" which
is never registered in DT case.
While at it, also make da8xx_wdt_device static since there is no need
for it to be globally visible.
Tested machine reboot with both DT and non-DT boot on DA850 EVM.
Signed-off-by: Kumar, Anil <anilkumar.v@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add I2C0 device tree and pin muxing information to da850-evm.
Also, add OF_DEV_AUXDATA for I2C0 controller driver in da850
board dt file to use I2C0 clock.
Verified i2c0 node gets created in sys class interface as
"/sys/class/i2c-dev/i2c-0/subsystem/i2c-0".
nsekhar@ti.com: tested using i2cdetect and i2cdump.
Signed-off-by: Vishwanathrao Badarkhe, Manish <manishv.b@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The device->state_count is initialized in the cpuidle_register_device
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Len Brown <len.brown@intel.com>
With one function handling the idle state and a single variable,
the usage of the davinci_ops is overkill.
This patch removes these ops and simplify the code.
Furthermore, the 'driver_data' field is no longer used, we have
1 of the 3 remaining user of this field removed.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The patch is mindless, it just moves the idle function below in the file
in order to prevent forward declaration in the next patch.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Len Brown <len.brown@intel.com>
That will allow to cleanup the rest of the code right after,
because the ops won't make sense.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Enabling UART FIFO in bootloader caused the kernel infinite
loop on S5PV210 due to uninitialized fifo_max and fifo_mask global
variables. This patch adds the correct initialization.
Signed-off-by: Alexey Galakhov <agalakhov@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Symbol S3C_DEV_USB_HOST should be defined to avoid this problem.
LINK vmlinux
LD vmlinux.o
MODPOST vmlinux.o
WARNING: modpost: Found 2 section mismatch(es).
To see full details build your kernel with:
'make CONFIG_DEBUG_SECTION_MISMATCH=y'
GEN .version
CHK include/generated/compile.h
UPD include/generated/compile.h
CC init/version.o
LD init/built-in.o
arch/arm/mach-s3c24xx/built-in.o:(.init.data+0x660): undefined reference to `s3c_device_ohci'
make: *** [vmlinux] Error 1
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Pull ARM fixes from Russell King:
"I was going to hold these off until v3.8 was out, and send them with a
stable tag, but as everyone else is pushing much bigger fixes which
Linus is accepting, let's save people from the hastle of having to
patch v3.8 back into working or use a stable kernel.
Looking at the diffstat, this really is high value for its size; this
is miniscule compared to how the -rc6 to tip diffstat currently looks.
So, four patches in this set:
- Punit Agrawal reports that the kernel no longer boots on MPCore due
to a new assumption made in the GIC code which isn't true of
earlier GIC designs. This is the biggest change in this set.
- Punit's boot log also revealed a bunch of WARN_ON() dumps caused by
the DT-ification of the GIC support without fixing up non-DT
Realview - which now sees a greater number of interrupts than it
did before.
- A fix for the DMA coherent code from Marek which uses the wrong
check for atomic allocations; this can result in spinlock lockups
or other nasty effects.
- A fix from Will, which will affect all Android based platforms if
not applied (which use the 2G:2G VM split) - this causes
particularly 'make' to misbehave unless this bug is fixed."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7641/1: memory: fix broken mmap by ensuring TASK_UNMAPPED_BASE is aligned
ARM: DMA mapping: fix bad atomic test
ARM: realview: ensure that we have sufficient IRQs available
ARM: GIC: fix GIC cpumask initialization
The missing include led to a implcit declaration warning:
In file included from arch/arm/mach-s3c24xx/mach-osiris.c:34:0:
include/linux/platform_data/i2c-s3c2410.h:37:26: warning: 'struct platform_device' declared inside parameter list [enabled by default]
include/linux/platform_data/i2c-s3c2410.h:37:26: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default]
include/linux/platform_data/i2c-s3c2410.h:66:38: warning: 'struct platform_device' declared inside parameter list [enabled by default]
include/linux/platform_data/i2c-s3c2410.h:67:38: warning: 'struct platform_device' declared inside parameter list [enabled by default]
include/linux/platform_data/i2c-s3c2410.h:68:38: warning: 'struct platform_device' declared inside parameter list [enabled by default]
include/linux/platform_data/i2c-s3c2410.h:69:38: warning: 'struct platform_device' declared inside parameter list [enabled by default]
include/linux/platform_data/i2c-s3c2410.h:70:38: warning: 'struct platform_device' declared inside parameter list [enabled by default]
include/linux/platform_data/i2c-s3c2410.h:71:38: warning: 'struct platform_device' declared inside parameter list [enabled by default]
include/linux/platform_data/i2c-s3c2410.h:72:38: warning: 'struct platform_device' declared inside parameter list [enabled by default]
include/linux/platform_data/i2c-s3c2410.h:73:38: warning: 'struct platform_device' declared inside parameter list [enabled by default]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The code to enter sleep is used by both the s3c2412 and s3c2416 and
was thus factored out into an extra config option.
But it seems it was forgotten to add the appropriate select to the
s3c2412 pm option, resulting in breakage when only compiling s3c2412
support.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
dpll_usb needs the clkdm association so the clkdm can be
turned on before a relock. All other dplls for omap4 belong
to the ALWON (always on) domain.
The association was present as part of the older data file
(clock44xx_data.c) but looks like got accidently dropped with
the common clk convertion.
More details of the patch which fixed this up in the older
data file can be dound here..
http://www.spinics.net/lists/linux-omap/msg63076.html
Adding the .clkdm_name as part of the clk_hw_omap struct also
means a new .init needs to be part of the clk_ops for dpll_usb
to initialise the clkdm.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit 1416408d {ARM: OMAP2+: PM: share some suspend-related functions
across OMAP2, 3, 4} moved suspend code to common place but now with
that change, for DT build on OMAP4, suspend hooks are not getting
registered which results in no suspend support.
The DT return condition is limited to PMIC and smartreflex
initialization and hence restrict it so that suspend ops gets
registered.
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
