This patch implements support for sampling of a touchscreen into
the MXS LRADC driver. The LRADC block allows configuring some of
it's channels into special mode where they either output the drive
voltage or sample it, allowing it to operate a 4-wire or 5-wire
resistive touchscreen.
In case the touchscreen mode is enabled, the LRADC slot #7 is
reserved for touchscreen only, therefore it is not possible to
sample 8 LRADC channels at time, but only 7 channels.
The touchscreen controller is configured such that the PENDOWN event
disables touchscreen interrupts and triggers execution of worker
thread, which then polls the touchscreen controller for X, Y and
Pressure values. This reduces the overhead of interrupt-driven
operation. Upon the PENUP event, the worker thread re-enables the
PENDOWN detection interrupt and exits.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Two new PHY drivers coming here: one for Samsung,
one for OMAP. Both architectures are adding USB3
support to mainline kernel.
The PHY layer now allows us to have mulitple PHYs
of the same type, which is necessary for platforms
which provide more than one USB peripheral port.
There's also a few cleanups here: removal of __dev*
annotations, conversion of a cast to to_delayed_work(),
and mxs-phy learns about ->set_suspend.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=c796
-----END PGP SIGNATURE-----
Merge tag 'xceiv-for-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: xceiv: patches for v3.9 merge window
Two new PHY drivers coming here: one for Samsung,
one for OMAP. Both architectures are adding USB3
support to mainline kernel.
The PHY layer now allows us to have mulitple PHYs
of the same type, which is necessary for platforms
which provide more than one USB peripheral port.
There's also a few cleanups here: removal of __dev*
annotations, conversion of a cast to to_delayed_work(),
and mxs-phy learns about ->set_suspend.
Added dt support for dwc3 core and update the documentation with
device tree binding information. Getting a PHY is now done using
devm_usb_get_phy_by_phandle() for dt boot.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Added a driver for usb3 phy that handles the interaction between usb phy
device and dwc3 controller.
This also includes device tree support for usb3 phy driver and
the documentation with device tree binding information is updated.
Currently writing to control module register is taken care in this
driver which will be removed once the control module driver is in place.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Start using the control module driver for powering on the PHY and for
writing to the mailbox instead of writing to the control module
registers on their own.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Added a new driver for the usb part of control module. This has an API
to power on the USB2 phy and an API to write to the mailbox depending on
whether MUSB has to act in host mode or in device mode.
Writing to control module registers for doing the above task which was
previously done in omap glue and in omap-usb2 phy will be removed.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Similarly as it was done for mx6q, use a DT lookup in order to make maintainance
task for the clock devices easier.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Added device tree support for usb3503 driver and add new document with device tree binding information.
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds support for reading display timings from DT into a struct
display_timings. The of_display_timing implementation supports multiple
subnodes. All children are read into an array, that can be queried.
If no native mode is specified, the first subnode will be used.
For cases where the graphics driver knows there can be only one
mode description or where the driver only supports one mode, a helper
function of_get_videomode is added, that gets a struct videomode from DT.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Afzal Mohammed <Afzal@ti.com>
Tested-by: Rob Clark <robclark@gmail.com>
Tested-by: Leela Krishna Amudala <leelakrishna.a@gmail.com>
This patch adds host phy support to samsung-usbphy driver and
further adds support for samsung's exynos5250 usb-phy.
Signed-off-by: Praveen Paneri <p.paneri@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The relation between PIN_BANK numbers and pio letters wasn't made very
clear.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The Allwinner SoCs have an IP module that handle both the muxing and the
GPIOs.
This IP has 8 banks of 32 bits, with a number of pins actually useful
for each of these banks varying from one to another, and depending on
the SoC used on the board.
This driver only implements the pinctrl part, the gpio part will come
eventually.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
SiRFmarco is a dual-core cortex-a9 SMP SoC from CSR. this patch
adds the .dtsi and a basic evb board .dts for it.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
The non-dt probing allowed passing the location via platform data from
the beginning. So make up leeway for device tree probing.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
this patche deletes hard code that registers clkdev by things like:
clk_register_clkdev(clk, NULL, "b0030000.nand");
clk_register_clkdev(clk, NULL, "b0040000.audio");
clk_register_clkdev(clk, NULL, "b0080000.usp");
prima2 clock controller becomes a clock provider and every dt node
just declares its clock sources by dt prop.
it also makes us easier to extend this driver to support both prima2
and marco as marco has different address mapping with prima2.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This adds a driver for the Tegra114 pinmux, and required
parameterization data for Tegra114.
The driver uses the common Tegra pincontrol driver utility
functions to implement the majority of the driver.
This driver is not compatible with the earlier NVIDIA's SoCs,
hence add new compatibile as "nvidia,tegra114-pinmux".
Originally written by Pritesh.
ldewangan:
- cleanup the patches,
- remove non-require tables.
- Use module_platform_driver() for driver registartion.
Signed-off-by: Pritesh Raithatha <praithatha@nvidia.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Adding support to parse device node data in order to get
required properties to set pmu isolation for usb-phy.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This driver uses usb_phy interface to interact with s3c-hsotg. Supports
phy_init and phy_shutdown functions to enable/disable usb phy. Support
will be extended to host controllers and more Samsung SoCs.
Signed-off-by: Praveen Paneri <p.paneri@samsung.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The NVIDIA's Tegra KBC has maximum 24 pins to make matrix keypad.
Any pin can be configured as row or column. The maximum column pin
can be 8 and maximum row pin can be 16.
Remove the assumption that all first 16 pins will be used as row
and remaining as columns and Add the property for configuring pins
to either row or column from DT. Update the devicetree binding
document accordingly.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds a very simple machine driver using the Wolfson wm9712 AC97
codec.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* DT binding for arc-uart
* With alll the bits in place we can now use DT probing.
Note that there's a bit of kludge right now because earlyprintk portion
of driver can't use the DT infrastrcuture to get resoures/plat_data.
This requires some infrastructre changes to of_flat_ framework
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Cox <alan@linux.intel.com>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NVIDIA's Tegra has multiple UART controller which supports:
- APB DMA based controller fifo read/write.
- End Of Data interrupt in incoming data to know whether end
of frame achieve or not.
- HW controlled RTS and CTS flow control to reduce SW overhead.
Add serial driver to use all above feature.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds basic DT bindings for OMAP GPMC.
The actual peripherals are instantiated from child nodes within the GPMC
node, and the only type of device that is currently supported is NAND.
Code was added to parse the generic GPMC timing parameters and some
documentation with examples on how to use them.
Successfully tested on an AM33xx board.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
[tony@atomide.com: updated to apply]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Support for loading the Renesas FSI driver via devicetree.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This adds the driver for the Tegra 2x AC97 host controller.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This series is based on:
git://server.prisktech.co.nz/git/linuxwmt.git tags/vt8500-multiplatform-3.9
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQ8NEiAAoJEAKiPfwuf9N/F0gH/0fAJkX6qPxVe33yPDbMFE1/
fKzPNM/FtzZh72updnNPKvAkO+V8ybDWo8tkn/nyvC7wNYNTFhlcFIc/zFyIwL1W
H2gcIl8aygdee6pRkigIi0alkK1ZHgClmdKJXnCv0nyHWLXqQCeiqCgAUYLBwfPA
4ZoVLs7djWiSF9TP51hDRbeG4Rzn38GQMxO8cmnk5qitfPc06hDP5Z6Hu8oLTXRn
ekGZI6aOqFz+RBHGGtQ813wH+kWrHu3/VHz8DPAVZ5KKz5bDFgcwcp07xQXCbfgX
kS2JytpJ+5Rmh6XVLTPNrxeaqht8MUwdL327rEVi0UO3z7CmYmVBf/6ajWW+QBU=
=Q4oq
-----END PGP SIGNATURE-----
Merge tag 'armsoc-3.9' of git://server.prisktech.co.nz/git/linuxwmt into next/soc
From Tony Prisk:
Add support for WM8750 and WM8850 SoCs.
* tag 'armsoc-3.9' of git://server.prisktech.co.nz/git/linuxwmt:
arm: vt8500: Add support for Wondermedia WM8750/WM8850
arm: vt8500: Remove remaining mach includes
arm: vt8500: Convert debug-macro.S to be multiplatform friendly
arm: vt8500: Remove single platform Kconfig options
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds support for the WM8750 (ARMv6) and WM8850 (ARMv7).
Devicetree documentation is updated for new SoCs.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
This implements pin multiplexing and pin configuration for
the Nomadik pin controller using the device tree.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@stericsson.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Philippe Langlais <philippe.langlais@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds a new devicetree binding for describing PSCI firmware
to Linux.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Support for loading the ak4642 codec module via devicetree.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add support to set polarity on PWM devices, allowing for inverted
duty cycles.
Also update the binding document to #pwm-cells = <3> to allow
passing the flags from devicetree.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
People are back from the holiday breaks, and it shows. Here are a bunch of
fixes for a number of platforms:
- A couple of small fixes for Nomadik
- A larger set of changes for kirkwood/mvebu
- uart driver selection, dt clocks, gpio-poweroff fixups,
a few __init annotation fixes and some error handling improvement
in their xor dma driver.
- i.MX had a couple of minor fixes (and a critical one for flexcan2
clock setup)
- MXS has a small board fix and a framebuffer bugfix
- A set of fixes for Samsung Exynos, fixing default bootargs and some
Exynos5440 clock issues
- A set of OMAP changes including PM fixes and a few sparse warning
fixups
All in all a bit more positive code delta than we'd ideally want to see
here, mostly from the OMAP PM changes, but nothing overly crazy.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=s9fE
-----END PGP SIGNATURE-----
Merge tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"People are back from the holiday breaks, and it shows. Here are a
bunch of fixes for a number of platforms:
- A couple of small fixes for Nomadik
- A larger set of changes for kirkwood/mvebu
- uart driver selection, dt clocks, gpio-poweroff fixups, a few
__init annotation fixes and some error handling improvement in
their xor dma driver.
- i.MX had a couple of minor fixes (and a critical one for flexcan2
clock setup)
- MXS has a small board fix and a framebuffer bugfix
- A set of fixes for Samsung Exynos, fixing default bootargs and some
Exynos5440 clock issues
- A set of OMAP changes including PM fixes and a few sparse warning
fixups
All in all a bit more positive code delta than we'd ideally want to
see here, mostly from the OMAP PM changes, but nothing overly crazy."
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (44 commits)
ARM: clps711x: Fix bad merge of clockevents setup
ARM: highbank: save and restore L2 cache and GIC on suspend
ARM: highbank: add a power request clear
ARM: highbank: fix secondary boot and hotplug
ARM: highbank: fix typos with hignbank in power request functions
ARM: dts: fix highbank cpu mpidr values
ARM: dts: add device_type prop to cpu nodes on Calxeda platforms
ARM: mx5: Fix MX53 flexcan2 clock
ARM: OMAP2+: am33xx-hwmod: Fix wrongly terminated am33xx_usbss_mpu_irqs array
pinctrl: mvebu: make pdma clock on dove mandatory
ARM: Dove: Add pinctrl clock to DT
dma: mv_xor: fix error handling for clocks
dma: mv_xor: fix error handling of mv_xor_channel_add()
arm: mvebu: Add missing ; for cpu node.
arm: mvebu: Armada XP MV78230 has only three Ethernet interfaces
arm: mvebu: Armada XP MV78230 has two cores, not one
clk: mvebu: Remove inappropriate __init tagging
ARM: Kirkwood: Use fixed-regulator instead of board gpio call
ARM: Kirkwood: Fix missing sdio clock
ARM: Kirkwood: Switch TWSI1 of 88f6282 to DT clock providers
...
when the port gets brought up. The other two are non-critical fixes,
which are sent together here, since it's still early -rc stage.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQ7Dk+AAoJEFBXWFqHsHzOUugIAJZblDy7ORFZhW0R8L4Be541
pS5aBGFY7VYCrL9BGUKGsLuITI+arbYFHc+H4nqhNMBAvgChPxJZMnaG4kp1Q5Vm
AVr9tNrwsauVHLlryUk4ekut4G4WWo1NDcFq4S6rxD/jxA/uP6rnMUCY6PX4LLL9
ZpGDb3BWQ2bbUaANu3cjc1I1/Gle1ir9LObm6ZC6l8MHTTG7hyTMHvS8eCZzmDbc
9z01ZrvTKn1AneeHOpArd2/jo14b6Kap8ykx2hdVUeBhIbZp3pomezZau9ya8/kB
+1BQVODdkOMzBm6gkIkfU3HbUPnIPL18MG/uKyD+f67YkX5YODinUVdq63upLxc=
=7yrS
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-3.8' of git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo:
It includes one critical fix - wrong flexcan2 clock will hang system
when the port gets brought up. The other two are non-critical fixes,
which are sent together here, since it's still early -rc stage.
* tag 'imx-fixes-3.8' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: mx5: Fix MX53 flexcan2 clock
ARM: dts: imx31-bug: Fix manufacturer compatible string
clk: imx: Remove 'clock-output-names' from the examples
This patch adds a PWM driver based on Atmel Timer Counter Block. The
Timer Counter Block is used in Waveform generator mode.
A Timer Counter Block provides up to 6 PWM devices grouped by 2:
* group 0 = PWM 0 and 1
* group 1 = PWM 2 and 3
* group 2 = PMW 4 and 5
PWM devices in a given group must be configured with the same period
value. If a PWM device in a group tries to change the period value and
the other device is already configured with a different value an error
will be returned.
This driver requires device tree support. The Timer Counter Block number
used to create a PWM chip is given by the tc-block field in an
"atmel,tcb-pwm" compatible node.
This patch was tested on kizbox board (at91sam9g20 SoC) with pwm-leds.
Signed-off-by: Boris BREZILLON <linux-arm@overkiz.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
dw_dmac driver already supports device tree but it used to have its platform
data passed the non-DT way.
This patch does following changes:
- pass platform data via DT, non-DT way still takes precedence if both are used.
- create generic filter routine
- Earlier slave information was made available by slave specific filter routines
in chan->private field. Now, this information would be passed from within dmac
DT node. Slave drivers would now be required to pass bus_id (a string) as
parameter to this generic filter(), which would be compared against the slave
data passed from DT, by the generic filter routine.
- Update binding document
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[Fixed __devinit usage]
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Some semicolons were left out in the examples.
The #dma-channels and #dma-requests properties have a prefix
that is, by convention, reserved for cell size properties.
Rename those properties to dma-channels and dma-requests.
Signed-off-by: Matt Porter <mporter@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
This is based upon the work by Benoit Cousson [1] and Nicolas Ferre [2]
to add some basic helpers to retrieve a DMA controller device_node and the
DMA request/channel information.
Aim of DMA helpers
- The purpose of device-tree is to describe the capabilites of the hardware.
Thinking about DMA controllers purely from the context of the hardware to
begin with, we can describe a device in terms of a DMA controller as
follows ...
1. Number of DMA controllers
2. Number of channels (maybe physical or logical)
3. Mapping of DMA requests signals to DMA controller
4. Number of DMA interrupts
5. Mapping of DMA interrupts to channels
- With the above in mind the aim of the DT DMA helper functions is to extract
the above information from the DT and provide to the appropriate driver.
However, due to the vast number of DMA controllers and not all are using a
common driver (such as DMA Engine) it has been seen that this is not a
trivial task. In previous discussions on this topic the following concerns
have been raised ...
1. How does the binding support devices with multiple DMA controllers?
2. How to support both legacy DMA controllers not using DMA Engine as
well as those that support DMA Engine.
3. When using with DMA Engine how do we support the various
implementations where the opaque filter function parameter differs
between implementations?
4. How do we handle DMA channels that are identified with a string
versus a integer?
- Hence the design of the DMA helpers has to accomodate the above or align on
an agreement what can be or should be supported.
Design of DMA helpers
1. Registering DMA controllers
In the case of DMA controllers that are using DMA Engine, requesting a
channel is performed by calling the following function.
struct dma_chan *dma_request_channel(dma_cap_mask_t mask,
dma_filter_fn filter_fn,
void *filter_param);
The mask variable is used to match a type of the device controller in a list
of controllers. The filter_fn and filter_param are used to identify the
required dma channel and return a handle to the dma channel of type dma_chan.
From the examples I have seen, the mask and filter_fn are constant
for a given DMA controller and therefore, we can specify these as controller
specific data when registering the DMA controller with the device-tree DMA
helpers.
The filter_param variable is of an unknown type and is typically specific
to the DMA engine implementation for a given DMA controller. To allow some
flexibility in the type and formating of this filter_param we employ an
xlate to translate the device-tree binding information into the appropriate
format. The xlate function used for a DMA controller can also be specified
when registering the DMA controller with the device-tree DMA helpers.
Based upon the above, a function for registering the DMA controller with the
DMA helpers now looks like the below. The data variable is used to pass a
pointer to DMA controller specific data used by the xlate function.
int of_dma_controller_register(struct device_node *np,
struct dma_chan *(*of_dma_xlate)
(struct of_phandle_args *, struct of_dma *),
void *data)
For example, in the case where DMA engine is used, we define the following
structure (that stores the DMA engine capability mask and filter function)
and pass this to the data variable in the above function.
struct of_dma_filter_info {
dma_cap_mask_t dma_cap;
dma_filter_fn filter_fn;
};
2. Representing and requesting channel information
Please see the dma binding documentation included in this patch for a
description of how DMA controllers and client information should be
represented with device-tree. For more information on how this binding
came about please see [3]. In addition to this, feedback received from
the Linux kernel summit showed a consensus (among those who attended) to
use a name to identify DMA client information [4].
A DMA channel can be requested by calling the following function, where name
is a required parameter used for identifying a DMA channel. This function
has been designed to return a structure of type dma_chan to work with the
DMA engine driver. Note that if DMA engine is used then drivers should be
using the DMA engine API dma_request_slave_channel() (implemented in part 2
of this series, "dmaengine: add helper function to request a slave DMA
channel") which will in turn call the below function if device-tree is
present. The aim being to have a common DMA engine interface regardless of
whether device tree is being used.
struct dma_chan *of_dma_request_slave_channel(struct device_node *np,
char *name)
3. Supporting legacy devices not using DMA Engine
These devices present a problem, as there may not be a uniform way to easily
support them with regard to device tree. Ideally, these should be migrated
to DMA engine. However, if this is not possible, then they should still be
able to use this binding, the only constaint imposed by this implementation
is that when requesting a DMA channel via of_dma_request_slave_channel(), it
will return a type of dma_chan.
This implementation has been tested on OMAP4430 using the kernel v3.6-rc5. I
have validated that MMC is working on the PANDA board with this implementation.
My development branch for testing on OMAP can be found here [5].
v6: - minor corrections in DMA binding documentation
v5: - minor update to binding documentation
- added loop to exhaustively search for a slave channel in the case where
there could be alternative channels available
v4: - revert the removal of xlate function from v3
- update the proposed binding format and APIs based upon discussions [3]
v3: - avoid passing an xlate function and instead pass DMA engine parameters
- define number of dma channels and requests in dma-controller node
v2: - remove of_dma_to_resource API
- make property #dma-cells required (no fallback anymore)
- another check in of_dma_xlate_onenumbercell() function
[1] http://article.gmane.org/gmane.linux.drivers.devicetree/12022
[2] http://article.gmane.org/gmane.linux.ports.arm.omap/73622
[3] http://marc.info/?l=linux-omap&m=133582085008539&w=2
[4] http://pad.linaro.org/arm-mini-summit-2012
[5] https://github.com/jonhunter/linux/tree/dev-dt-dma
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <djbw@fb.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Some devices, Buffalo Linkstation LS-XHL and LS-CHLv2 for example,
power-off by restarting to letting u-boot hold the SoC until the user
presses a key. Add a generic driver to implement this. It binds a function
to pm_power_off, which calls arm_pm_restart.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
The QNAP NAS boxes have a microcontroller attached to the SoCs second
serial port. By sending it a simple command, it will turn the power for
the board off. This driver registers a function for pm_power_off to send
such a command.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Improve the documentation to clarify level vs edge triggered power off.
Improve the comments for level vs edge triggered power off.
Make use of gpio_is_valid().
Reported-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
'clock-output-names' is not used in any of the dts/dtsi files for i.mx.
Remove it from the examples, so that the example and the real usage in the
dtsi files can match.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
- i.MX5 register configuration
- Swap a kfree to devm_kfree() to avoid memory
corruption in the at91 driver
- Add the missing device tree binding doc for the
SIRF pin controller
- Enable the SIRF GPIO pull up/down configuration
from the device tree, it was previously retired
from the hard-coded approach.
- NULL check for the prcm_base in the Nomadik pin
controller.
- Provide the prcm_base from the device tree in the
DT boot path for the Nomadik pin controller.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=ca6M
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl fixes from Linus Walleij:
"A first round of pinctrl fixes for v3.8:
- i.MX5 register configuration
- Swap a kfree to devm_kfree() to avoid memory corruption in the at91
driver
- Add the missing device tree binding doc for the SIRF pin controller
- Enable the SIRF GPIO pull up/down configuration from the device
tree, it was previously retired from the hard-coded approach.
- NULL check for the prcm_base in the Nomadik pin controller.
- Provide the prcm_base from the device tree in the DT boot path for
the Nomadik pin controller."
* tag 'pinctrl-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
ARM: ux500: add pinctrl address resources
pinctrl: nomadik: return if prcm_base is NULL
pinctrl: sirf: enable GPIO pullup/down configuration from dts
pinctrl: sirf: add missing DT-binding document
pinctrl: fix comment mistake
drivers/pinctrl/pinctrl-at91.c: convert kfree to devm_kfree
pinctrl: imx5: fix GPIO_8 pad CAN1_RXCAN configuration
This patch adds device tree support for imx keypad driver.
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Update the common machine driver to support more boards including Zoom2 and
SDP3430.
- Support for voice port of twl4030
- HS jack plug detection support
- The audio routing can be fine tuned via pdata or via provided routing
table from DT.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add DT support for twl4030_wdt. This is needed to get twl4030_wdt to
probe when booting with DT.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add DT support for the TI TPS51632. Add device binding document also.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
commit 7bec207427 remove sirfsoc_gpio_set_pull function,
this patches takes the feature back by adding sirf,pullups and
sirf,pulldowns prop in dts, and the driver will set the GPIO
pull according to the dts.
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
