Since the function ipu_dmfc_init_channel() always returns zero, we may
change the return type to void to simplify the code.
Signed-off-by: Liu Ying <gnuiyl@gmail.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
To avoid race condition issue, we should protect the function
ipu_dmfc_init_channel() with the mutex dmfc->priv->mutex, since it
configures the register DMFC_GENERAL1 at runtime which contains
several control bits for various display channels. This matches
better with fine grained locking logic in upper layer.
Signed-off-by: Liu Ying <gnuiyl@gmail.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The IMX dw_hdmi driver just called platform_set_drvdata() to get
your hopes up that maybe, somehow, you'd be able to retrieve the 'struct
imx_hdmi' from a pointer to the 'struct device'. You can't. When
we call dw_hdmi_bind() the main driver calls dev_set_drvdata(), which
clobbers our setting.
Let's just remove the platform_set_drvdata() to avoid dashing people's
hopes.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The drm_encoder_cleanup() was missing both from the error path of
dw_hdmi_imx_bind(). This caused a crash when slub_debug was
enabled and we ended up deferring probe of HDMI at boot.
This call isn't needed from unbind() because if dw_hdmi_bind() returns
no error then it takes over the job of freeing the encoder (in
dw_hdmi_unbind).
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The driver already advertises multi-planar YUV support, but
previously the U/V offset and stride setup was missing.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The IPU addresses multiplanar formats using a base address and relative
offsets for the secondary planes. Since those offsets must be positive
and not too large, and none of the plane parameters except the base address
may be changed while scanout is active, store the pitches and u/v offsets
and check all values against IDMAC limitations.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Let ipu_cpmem_set_yuv_planar_full take a DRM_FORMAT instead of a
V4L2_PIXFMT and allow better control over U/V stride, U offset and
V offset settings in the CPMEM.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Pull up was reported as pull down and vice versa. Fix this.
Fixes: 8f1774a2a9 "pinctrl: nomadik: improve GPIO debug prints"
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When the kernel is running at EL2, it doesn't need init_hyp_mode() to
configure page tables for HYP. This function also registers the CPU
hotplug and lower power notifiers that cause HYP to be re-initialised
after the CPU has been reset.
To avoid losing the register state that controls stage2 translation, move
the registering of these notifiers into init_subsystems(), and add a
is_kernel_in_hyp_mode() path to each callback.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Fixes: 1e947bad0b ("arm64: KVM: Skip HYP setup when already running in HYP")
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
In the error path, event_file not being NULL is used to determine
whether the event itself still needs to be free'd, so fix it up to
avoid leaking.
Reported-by: Leon Yu <chianglungyu@gmail.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Fixes: 130056275a ("perf: Do not double free")
Link: http://lkml.kernel.org/r/87twk06yxp.fsf@ashishki-desk.ger.corp.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Stephane reported that commit:
3cbaa59069 ("perf: Fix ctx time tracking by introducing EVENT_TIME")
introduced a regression wrt. time tracking, as easily observed by:
> This patch introduce a bug in the time tracking of events when
> multiplexing is used.
>
> The issue is easily reproducible with the following perf run:
>
> $ perf stat -a -C 0 -e branches,branches,branches,branches,branches,branches -I 1000
> 1.000730239 652,394 branches (66.41%)
> 1.000730239 597,809 branches (66.41%)
> 1.000730239 593,870 branches (66.63%)
> 1.000730239 651,440 branches (67.03%)
> 1.000730239 656,725 branches (66.96%)
> 1.000730239 <not counted> branches
>
> One branches event is shown as not having run. Yet, with
> multiplexing, all events should run especially with a 1s (-I 1000)
> interval. The delta for time_running comes out to 0. Yet, the event
> has run because the kernel is actually multiplexing the events. The
> problem is that the time tracking is the kernel and especially in
> ctx_sched_out() is wrong now.
>
> The problem is that in case that the kernel enters ctx_sched_out() with the
> following state:
> ctx->is_active=0x7 event_type=0x1
> Call Trace:
> [<ffffffff813ddd41>] dump_stack+0x63/0x82
> [<ffffffff81182bdc>] ctx_sched_out+0x2bc/0x2d0
> [<ffffffff81183896>] perf_mux_hrtimer_handler+0xf6/0x2c0
> [<ffffffff811837a0>] ? __perf_install_in_context+0x130/0x130
> [<ffffffff810f5818>] __hrtimer_run_queues+0xf8/0x2f0
> [<ffffffff810f6097>] hrtimer_interrupt+0xb7/0x1d0
> [<ffffffff810509a8>] local_apic_timer_interrupt+0x38/0x60
> [<ffffffff8175ca9d>] smp_apic_timer_interrupt+0x3d/0x50
> [<ffffffff8175ac7c>] apic_timer_interrupt+0x8c/0xa0
>
> In that case, the test:
> if (is_active & EVENT_TIME)
>
> will be false and the time will not be updated. Time must always be updated on
> sched out.
Fix this by always updating time if EVENT_TIME was set, as opposed to
only updating time when EVENT_TIME changed.
Reported-by: Stephane Eranian <eranian@google.com>
Tested-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: kan.liang@intel.com
Cc: namhyung@kernel.org
Fixes: 3cbaa59069 ("perf: Fix ctx time tracking by introducing EVENT_TIME")
Link: http://lkml.kernel.org/r/20160329072644.GB3408@twins.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
- Fix determination of a callchain node's childlessness in
the top/report TUI, which was preventing navigating some
callchains, --stdio unnaffected (Andres Freund)
- Fix jitdump's genelf assumption that PowerPC is big endian
only (Anton Blanchard)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=GmW5
-----END PGP SIGNATURE-----
Merge tag 'perf-urgent-for-mingo-20160330' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent
Pull perf/urgent fixes from Arnaldo Carvalho de Melo:
- Fix determination of a callchain node's childlessness in
the top/report TUI, which was preventing navigating some
callchains, --stdio unnaffected (Andres Freund)
- Fix jitdump's genelf assumption that PowerPC is big endian
only (Anton Blanchard)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
commit b37d83a6a4 ("usb: Parse the new USB 3.1 SuperSpeedPlus Isoc
endpoint companion descriptor") caused a regression in 4.6-rc1 and fails
to parse SuperSpeed endpoint companion descriptors.
The new SuperSpeedPlus Isoc endpoint companion parsing code incorrectly
decreased the the remaining buffer size before comparing the size with the
expected length of the descriptor.
This lead to possible failure in reading the SuperSpeed endpoint companion
descriptor of the last endpoint, displaying a message like:
"No SuperSpeed endpoint companion for config 1 interface 0 altsetting 0
ep 129: using minimum values"
Fix it by decreasing the size after comparing it.
Also finish all the SS endpoint companion parsing before calling SSP isoc
endpoint parsing function.
Fixes: b37d83a6a4
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix potential out-of-bounds write to urb->transfer_buffer
usbip handles network communication directly in the kernel. When receiving a
packet from its peer, usbip code parses headers according to protocol. As
part of this parsing urb->actual_length is filled. Since the input for
urb->actual_length comes from the network, it should be treated as untrusted.
Any entity controlling the network may put any value in the input and the
preallocated urb->transfer_buffer may not be large enough to hold the data.
Thus, the malicious entity is able to write arbitrary data to kernel memory.
Signed-off-by: Ignat Korchagin <ignat.korchagin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A couple fixes for the new SuperSpeedPlus that went
in during this merge window. Also two minor fixes
for dwc3 (one for setting endpoint naming correctly
and another to improve time spent in our reset
sequence) and an old bug fix on Atmel UDC which was
disabling endpoints when it shouldn't.
There's also a build breakage fix to the qcom phy
driver and a fix to the f_midi gadget to avoid a
race condition with f_midi_transmit().
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJW+64KAAoJEIaOsuA1yqRE4GIP/jjyMQct/zUKhmYwc4HHh0e5
cBN30H8hv6d7vz24ilxw6xOCfwOgr2YQKFh7i6hSORhP1yKc7orlx8M8QXqhvGbB
nCWvCSpNyNQTQUM3D42Ty71mVNBumQvDdSUDtBoEit/t8VxzoYvIz/7TZquKCAoG
R+nSb4grFWurFi61EgszOFm3/w37S0XDUfHkjIwuJWkUGTn2x1UpPef7ALzilDeg
WNKCC7ZMJa4pXBWcpjof6OE3slKB0/5Qqb5j5mHcL+BQ2uvQdN5LW3rxSfJiFDBQ
DNxuHhwScXk1oWrs6bwAPbbSdyNJo+1KfIpMqIQAgCsVh4O+ANLU5g5JQwHDdEUy
lPRzRTOQT1Cowmh/yV8VA47UX7sx9kz3qU1uGJRbVKzgW/k9TzkOU7RlN2UU5R/Y
VbDripDMnZqf8oraDMWClbpLX48hrb456tEjqigE4baiqEc5qY8nj+FfO2QVjluS
fOMPFiQbLFwD5w7CXT+i9HzgR/hHVS1CoYc7mHP52+YRF9GUd3LZYmAL+UND864D
aS+6NzgVMvSAvJDYPzhtLo7dzkEnjs6l8rl2yHlkiMg0i/V2G5vq1r1f6SgnVyZR
UrSollFuIuI2G/PdemM0aHmJZ+MerbiNxq0Rf14cJqJPuRRbXtcuZGyb3m/3vdMJ
2In8/60pWpw6fYj2iSeH
=cLYy
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v4.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.6-rc2
A couple fixes for the new SuperSpeedPlus that went
in during this merge window. Also two minor fixes
for dwc3 (one for setting endpoint naming correctly
and another to improve time spent in our reset
sequence) and an old bug fix on Atmel UDC which was
disabling endpoints when it shouldn't.
There's also a build breakage fix to the qcom phy
driver and a fix to the f_midi gadget to avoid a
race condition with f_midi_transmit().
We should try to trigger automount *before* bailing out on negative dentry.
Reported-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Reported-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Reported-by: Arend van Spriel <arend@broadcom.com>
Tested-by: Arend van Spriel <arend@broadcom.com>
Tested-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
We need to have the WWN fully initialized before addig default groups to it,
so add a new method to add these groups after the WWN has been initialized.
Also remove the default groups in the core while we're at it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The iSCSI targets wants to add a default group, for which we need to
have the list of default groups initialized previously.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Instead we can clean up the list of default ACLs in core code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now the rdma core offers a QP draining service in v4.6-rc1,
use it instead of our own.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
If a directory has a large number of empty blocks, iterating over all
of them can take a long time, leading to scheduler warnings and users
getting irritated when they can't kill a process in the middle of one
of these long-running readdir operations. Fix this by adding checks to
ext4_readdir() and ext4_htree_fill_tree().
Reported-by: Benjamin LaHaise <bcrl@kvack.org>
Google-Bug-Id: 27880676
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
nios2 builds fail with the following build error.
arch/nios2/kernel/prom.c: In function 'early_init_dt_scan_serial':
arch/nios2/kernel/prom.c💯2: error:
implicit declaration of function 'fdt_translate_address'
Commit c90fe9c039 ("of: earlycon: Move address translation to
of_setup_earlycon()") replaced fdt_translate_address() with
of_flat_dt_translate_address() but missed updating the nios2 code.
Fixes: c90fe9c039 ("of: earlycon: Move address translation to of_setup_earlycon()")
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Ley Foon Tan <lftan@altera.com>
If the lower or upper directory of an overlayfs mount belong to a btrfs
file system and we fsync the file through the overlayfs' merged directory
we ended up accessing an inode that didn't belong to btrfs as if it were
a btrfs inode at btrfs_sync_file() resulting in a crash like the following:
[ 7782.588845] BUG: unable to handle kernel NULL pointer dereference at 0000000000000544
[ 7782.590624] IP: [<ffffffffa030b7ab>] btrfs_sync_file+0x11b/0x3e9 [btrfs]
[ 7782.591931] PGD 4d954067 PUD 1e878067 PMD 0
[ 7782.592016] Oops: 0002 [#6] PREEMPT SMP DEBUG_PAGEALLOC
[ 7782.592016] Modules linked in: btrfs overlay ppdev crc32c_generic evdev xor raid6_pq psmouse pcspkr sg serio_raw acpi_cpufreq parport_pc parport tpm_tis i2c_piix4 tpm i2c_core processor button loop autofs4 ext4 crc16 mbcache jbd2 sr_mod cdrom sd_mod ata_generic virtio_scsi ata_piix virtio_pci libata virtio_ring virtio scsi_mod e1000 floppy [last unloaded: btrfs]
[ 7782.592016] CPU: 10 PID: 16437 Comm: xfs_io Tainted: G D 4.5.0-rc6-btrfs-next-26+ #1
[ 7782.592016] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS by qemu-project.org 04/01/2014
[ 7782.592016] task: ffff88001b8d40c0 ti: ffff880137488000 task.ti: ffff880137488000
[ 7782.592016] RIP: 0010:[<ffffffffa030b7ab>] [<ffffffffa030b7ab>] btrfs_sync_file+0x11b/0x3e9 [btrfs]
[ 7782.592016] RSP: 0018:ffff88013748be40 EFLAGS: 00010286
[ 7782.592016] RAX: 0000000080000000 RBX: ffff880133b30c88 RCX: 0000000000000001
[ 7782.592016] RDX: 0000000000000001 RSI: ffffffff8148fec0 RDI: 00000000ffffffff
[ 7782.592016] RBP: ffff88013748bec0 R08: 0000000000000001 R09: 0000000000000000
[ 7782.624248] R10: ffff88013748be40 R11: 0000000000000246 R12: 0000000000000000
[ 7782.624248] R13: 0000000000000000 R14: 00000000009305a0 R15: ffff880015e3be40
[ 7782.624248] FS: 00007fa83b9cb700(0000) GS:ffff88023ed40000(0000) knlGS:0000000000000000
[ 7782.624248] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 7782.624248] CR2: 0000000000000544 CR3: 00000001fa652000 CR4: 00000000000006e0
[ 7782.624248] Stack:
[ 7782.624248] ffffffff8108b5cc ffff88013748bec0 0000000000000246 ffff8800b005ded0
[ 7782.624248] ffff880133b30d60 8000000000000000 7fffffffffffffff 0000000000000246
[ 7782.624248] 0000000000000246 ffffffff81074f9b ffffffff8104357c ffff880015e3be40
[ 7782.624248] Call Trace:
[ 7782.624248] [<ffffffff8108b5cc>] ? arch_local_irq_save+0x9/0xc
[ 7782.624248] [<ffffffff81074f9b>] ? ___might_sleep+0xce/0x217
[ 7782.624248] [<ffffffff8104357c>] ? __do_page_fault+0x3c0/0x43a
[ 7782.624248] [<ffffffff811a2351>] vfs_fsync_range+0x8c/0x9e
[ 7782.624248] [<ffffffff811a237f>] vfs_fsync+0x1c/0x1e
[ 7782.624248] [<ffffffff811a24d6>] do_fsync+0x31/0x4a
[ 7782.624248] [<ffffffff811a2700>] SyS_fsync+0x10/0x14
[ 7782.624248] [<ffffffff81493617>] entry_SYSCALL_64_fastpath+0x12/0x6b
[ 7782.624248] Code: 85 c0 0f 85 e2 02 00 00 48 8b 45 b0 31 f6 4c 29 e8 48 ff c0 48 89 45 a8 48 8d 83 d8 00 00 00 48 89 c7 48 89 45 a0 e8 fc 43 18 e1 <f0> 41 ff 84 24 44 05 00 00 48 8b 83 58 ff ff ff 48 c1 e8 07 83
[ 7782.624248] RIP [<ffffffffa030b7ab>] btrfs_sync_file+0x11b/0x3e9 [btrfs]
[ 7782.624248] RSP <ffff88013748be40>
[ 7782.624248] CR2: 0000000000000544
[ 7782.661994] ---[ end trace 721e14960eb939bc ]---
This started happening since commit 4bacc9c923 (overlayfs: Make f_path
always point to the overlay and f_inode to the underlay) and even though
after this change we could still access the btrfs inode through
struct file->f_mapping->host or struct file->f_inode, we would end up
resulting in more similar issues later on at check_parent_dirs_for_sync()
because the dentry we got (from struct file->f_path.dentry) was from
overlayfs and not from btrfs, that is, we had no way of getting the dentry
that belonged to btrfs (we always got the dentry that belonged to
overlayfs).
The new patch from Miklos Szeredi, titled "vfs: add file_dentry()" and
recently submitted to linux-fsdevel, adds a file_dentry() API that allows
us to get the btrfs dentry from the input file and therefore being able
to fsync when the upper and lower directories belong to btrfs filesystems.
This issue has been reported several times by users in the mailing list
and bugzilla. A test case for xfstests is being submitted as well.
Fixes: 4bacc9c923 ("overlayfs: Make f_path always point to the overlay and f_inode to the underlay")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=101951
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=109791
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
Cc: stable@vger.kernel.org
Make the 2 byte padding in struct bpf_tunnel_key between tunnel_ttl
and tunnel_label members explicit. No issue has been observed, and
gcc/llvm does padding for the old struct already, where tunnel_label
was not yet present, so the current code works, but since it's part
of uapi, make sure we don't introduce holes in structs.
Therefore, add tunnel_ext that we can use generically in future
(f.e. to flag OAM messages for backends, etc). Also add the offset
to the compat tests to be sure should some compilers not padd the
tail of the old version of bpf_tunnel_key.
Fixes: 4018ab1875 ("bpf: support flow label for bpf_skb_{set, get}_tunnel_key")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 counters updates use a different macro than IPv4.
Fixes: 36cbb2452c ("udp: Increment UDP_MIB_IGNOREDMULTI for arriving unmatched multicasts")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Rick Jones <rick.jones2@hp.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To report flow control tx/rx settings accurately regardless of autoneg
setting, we should use link_info->req_flow_ctrl. Before this patch,
the reported settings were only correct when autoneg was on.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The typo caused the wrong flow control bit to be set.
Reported by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The size of every padded firmware message is specified in the first
HWRM_VER_GET response message. Use this value to pad every message
after that.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing code does the following:
allocate completion ring
initialize completion ring doorbell
disable interrupts on this completion ring by writing to the doorbell
We can have a race where firmware sends an asynchronous event to the host
after completion ring allocation and before doorbell is initialized.
When this happens driver can crash while ringing the doorbell using
uninitialized value as part of handling the IRQ/napi request.
Signed-off-by: Prashant Sreedharan <prashant.sreedharan@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 9b07e27f88 ("perf inject: Add jitdump mmap injection support")
incorrectly assumed that PowerPC is big endian only.
Simplify things by consolidating the define of GEN_ELF_ENDIAN and checking
for __BYTE_ORDER == __BIG_ENDIAN.
The PowerPC checks were also incorrect, they do not match what gcc
emits. We should first look for __powerpc64__, then __powerpc__.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: Carl Love <cel@us.ibm.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Cc: linuxppc-dev@lists.ozlabs.org
Fixes: 9b07e27f88 ("perf inject: Add jitdump mmap injection support")
Link: http://lkml.kernel.org/r/20160329175944.33a211cc@kryten
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The 4b3a321223 ("perf hists browser: Support flat callchains") commit
over-aggressively tried to optimize callchain_node__init_have_children().
That lead to --tui mode not allowing to expand call chain elements if a
call chain element had only one parent. That's why --inverted callgraphs
looked halfway sane, but plain ones didn't.
Revert that individual optimization, it wasn't really related to the
rest of the commit.
Signed-off-by: Andres Freund <andres@anarazel.de>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Fixes: 4b3a321223 ("perf hists browser: Support flat callchains")
Link: http://lkml.kernel.org/r/20160330190245.GB13305@awork2.anarazel.de
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
There is an issue when we use mavtap over team:
When we replug nic links from team0, the real nics's mc list will not
include the maddr for macvtap any more. then we can't receive pkts to
macvtap device, as they are filterred by mc list of nic.
In Bonding Driver, it syncs the uc/mc addrs in bond_enslave().
We will fix this issue on team by adding the port's uc/mc addrs sync in
team_port_add.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the following patch,
f2fs: split journal cache from curseg cache
journal cache is split from curseg cache. So IO write statistics should be
retrived from journal cache but not curseg->sum_blk. Otherwise, it will
get 0, and the stat is lost.
Signed-off-by: Shuoran Liu <liushuoran@huawei.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
In the encrypted symlink case, we should check its corrupted symname after
decrypting it.
Otherwise, we can report -ENOENT incorrectly, if encrypted symname starts with
'\0'.
Cc: stable 4.5+ <stable@vger.kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
When we detect support for 16bit VMID in ID_AA64MMFR1, we set the
VTCR_EL2_VS field to 1 to make use of 16bit vmids. But, with
commit 3a3604bc5e ("arm64: KVM: Switch to C-based stage2 init")
this is broken and we corrupt VTCR_EL2:T0SZ instead of updating the VS
field. VTCR_EL2_VS was actually defined to the field shift (19) and
not the real value for VS. This patch fixes the issue.
Fixes: commit 3a3604bc5e ("arm64: KVM: Switch to C-based stage2 init")
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
This patch should fix the issues seen with a recent fix to prevent
tunnel-in-tunnel frames from being generated with GRO. The fix itself is
correct for now as long as we do not add any devices that support
NETIF_F_GSO_GRE_CSUM. When such a device is added it could have the
potential to mess things up due to the fact that the outer transport header
points to the outer UDP header and not the GRE header as would be expected.
Fixes: fac8e0f579 ("tunnels: Don't apply GRO to multiple layers of encapsulation.")
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
in the case where qed_slowpath_irq_req is not called, rc is not
assigned and so qed_int_igu_enable will return a garbage value.
Fix this by initializing rc to 0.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Somehow my patch for commit cea8768f33 ("sctp: allow
sctp_transmit_packet and others to use gfp") missed two important
chunks, which are now added.
Fixes: cea8768f33 ("sctp: allow sctp_transmit_packet and others to use gfp")
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-By: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When NET_SWITCHDEV=n, switchdev_port_attr_set will return -EOPNOTSUPP,
we should ignore this error code and continue to set the ageing time.
Fixes: c62987bbd8 ("bridge: push bridge setting ageing_time down to switchdev")
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull crypto fix from Herbert Xu:
"This fixes a bug in pkcs7_validate_trust and its users where the
output value may in fact be taken from uninitialised memory"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
PKCS#7: pkcs7_validate_trust(): initialize the _trusted output argument
This fixes a bug from the configfs cleanup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ityW
-----END PGP SIGNATURE-----
Merge tag 'dlm-4.6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/linux-dlm
Pull dlm fix from David Teigland:
"This fixes a bug from the configfs cleanup"
* tag 'dlm-4.6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/linux-dlm:
dlm: config: Fix ENOMEM failures in make_cluster()
This patch adds a code to surely disable TX IRQ of the pipe before
starting TX DMAC transfer. Otherwise, a lot of unnecessary TX IRQs
may happen in rare cases when DMAC is used.
Fixes: e73a989 ("usb: renesas_usbhs: add DMAEngine support")
Cc: <stable@vger.kernel.org> # v3.1+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Jan reported this:
===
After enabling CONFIG_I2C_DEBUG_CORE my system was broken
(no network, console login not possible). System log was
flooded with the this message:
...
[ 608.052077] rtc-ds1307 0-0068: uevent
[ 608.052500] rtc-ds1307 0-0068: uevent
[ 608.052925] rtc-ds1307 0-0068: uevent
...
The culprit is the dev_dbg printk in the i2c uevent handler.
If this is activated (for instance by CONFIG_I2C_DEBUG_CORE)
it results in an endless loop with systemd-journald.
This happens if user-space scans the system log and reads the uevent
file to get information about a newly created device, which seems fair
use to me. Unfortunately reading the "uevent" file uses the same
function that runs for creating the uevent for a new device,
generating the next syslog entry.
Ideally user-space would implement a recursion detection and
after reading the same device file for the 1000th time call it a
day, but nevertheless I think we should avoid this problem by
removing the debug print completely or using another print variant.
The same problem seems to be reported here:
https://bugs.freedesktop.org/show_bug.cgi?id=76886
===
His patch converted the message to pr_debug, but I think the debug can
simply go. We have other means to see code paths these days. This
enables us to clean up the function some more while we are here.
Reported-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Tested-by: Jan Glauber <jglauber@cavium.com>
Josh Boyer reported that my recent change to uapi/linux/swab.h broke the Qemu build:
bc27fb68aa ("include/uapi/linux/byteorder, swab: force inlining of some byteswap operations")
Unfortunately, UAPI headers don't include compiler.h so fixing it there is not enough,
add an __always_inline definition to uapi/linux/stddef.h instead.
Testcase: "make headers_install" and try to compile this:
#include <linux/swab.h>
void main() {}
Reported-by: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David Rientjes <rientjes@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Thomas Graf <tgraf@suug.ch>
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/1459289697-12875-1-git-send-email-dvlasenk@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
buflen by default (256) is smaller than wMaxPacketSize (512) in high-speed
devices.
That caused the OUT endpoint to freeze if the host send any data packet of
length greater than 256 bytes.
This is an example dump of what happended on that enpoint:
HOST: [DATA][Length=260][...]
DEVICE: [NAK]
HOST: [PING]
DEVICE: [NAK]
HOST: [PING]
DEVICE: [NAK]
...
HOST: [PING]
DEVICE: [NAK]
This patch fixes this problem by setting the minimum usb_request's buffer size
for the OUT endpoint as its wMaxPacketSize.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Here on Ubuntu/precise I have GNU/coreutils v8.13 installed
where 'basename -s' is not supported.
The result is that run_tests.sh is not done properly.
How to reproduce:
$ cd $BUILD_DIR
$ LC_ALL=C make -C tools/ liblockdep
$ cd tools/lib/lockdep/
$ LC_ALL=C ./run_tests.sh
basename: invalid option -- 's'
Try `basename --help' for more information.
... timeout: failed to run command `./tests/': Permission denied
FAILED!
rm: cannot remove `tests/': Is a directory
Due to unsupported basename the tests programs are not generated
and cannot be removed.
Fix this by doing a compatible basename invocation and check for
the existence of generated tests programs.
For more details see this LKML thread:
http://marc.info/?t=145906667300001&r=1&w=2
Signed-off-by: Sedat Dilek <sedat.dilek@gmail.com>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sasha Levin <sasha.levin@oracle.com> (maintainer:LIBLOCKDEP)
Cc: Shuah Khan <shuahkh@osg.samsung.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-fsdevel <linux-fsdevel@vger.kernel.org>
Link: http://lkml.kernel.org/r/1459326169-7009-1-git-send-email-sedat.dilek@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
