This change adds the first network driver for the tile architecture,
supporting the on-chip XGBE and GBE shims.
The infrastructure is present for the TILE-Gx networking drivers (another
three source files in the new directory) but for now the the actual
tilegx sources are waiting on releasing hardware to initial customers.
Note that arch/tile/include/hv/* are "upstream" headers from the
Tilera hypervisor and will probably benefit less from LKML review.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Commit d09c23de intended to add a 30ms delay to give the ADD time to
detect any TVs connected. However, it used the sdvo->is_tv flag to do so
which is dependent upon the previous detection result and not whether the
output supports TVs.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Vegard Nossum found a unix socket OOM was possible, posting an exploit
program.
My analysis is we can eat all LOWMEM memory before unix_gc() being
called from unix_release_sock(). Moreover, the thread blocked in
unix_gc() can consume huge amount of time to perform cleanup because of
huge working set.
One way to handle this is to have a sensible limit on unix_tot_inflight,
tested from wait_for_unix_gc() and to force a call to unix_gc() if this
limit is hit.
This solves the OOM and also reduce overall latencies, and should not
slowdown normal workloads.
Reported-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only make swapper_pg_dir readonly and pinned when generic x86 architecture code
(which also starts on initial_page_table) switches to it. This helps ensure
that the generic setup paths work on Xen unmodified. In particular
clone_pgd_range writes directly to the destination pgd entries and is used to
initialise swapper_pg_dir so we need to ensure that it remains writeable until
the last possible moment during bring up.
This is complicated slightly by the need to avoid sharing kernel PMD entries
when running under Xen, therefore the Xen implementation must make a copy of
the kernel PMD (which is otherwise referred to by both intial_page_table and
swapper_pg_dir) before switching to swapper_pg_dir.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
I didn't know the difference between the two when I wrote this code in
commit c30116c6f0.
Signed-off-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Add new MUTE key seen on Medion Akoya AIO PC P4010D using MSI motherboard
(Product Name: MS-7621)
Reported-and-tested-by: Mark Huijgen <mark.sf.net@huijgen.tk>
Signed-off-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Asus UL30A has a 3G chip, but the radio is disabled by default.
The DSDT also reference a WIMAX device, which is not present on this model.
This patch adds two new files: wwan and wimax to control WWAN and
WIMAX devices. It does not use rfkill, because like WLED and BLED,
we don't know yet that the two ACPI functions will always control the
radio, they may control only the leds on some hardware.
We may add rfkill switchs later.
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
This fixes the following:
CC [M] drivers/platform/x86/eeepc-wmi.o
drivers/platform/x86/eeepc-wmi.c:322: warning: initialization from incompatible pointer type
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Some of the IBM servers that are supported by ibm_rtl
can run in both Legacy mode (BIOS) and in UEFI mode.
When running in UEFI mode, it is possible that the
EBDA table exists but cannot be mapped and reports
errors. We need to make sure that by default we don't
try to probe the machines if they are running in UEFI
mode.
Signed-off-by: Vernon Mauery <vernux@us.ibm.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Allow all IBM machines to pass the DMI check so that we
don't have to add them one by one to the driver. Any IBM
machine that has the _RTL_ table in the EBDA will work.
Signed-off-by: Vernon Mauery <vernux@us.ibm.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Delete successive assignments to the same location.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression i;
@@
*i = ...;
i = ...;
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Based on cpufv text from sysfs-platform-eeepc-laptop that
has almost same behavior.
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Corentin Chary <corentincj@iksaif.net>
A lone FN key press on a Toshiba Portégé R700 without another key in
conjunction results in an ACPI event and a spurious error message on
the console.
Add a key entry to map this event to a KEY_FN keypress. This prevents
the console message.
Signed-off-by: Jon Dowland <jmtd@debian.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Fix printk format warning:
drivers/platform/x86/ibm_rtl.c:305:warning: format '%#llx' expects type 'long long unsigned int', but argument 2 has type 'phys_addr_t'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Keith Mannthey <kmannth@us.ibm.com>
Cc: Vernon Mauery <vernux@us.ibm.com>
Cc: platform-driver-x86@vger.kernel.org
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
The patch enables ALC887-VD to use the DAC at nid 0x26,
which makes it possible to use this DAC for e g Headphone
volume.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Return PTR_ERR(omap3pandora_dac_reg) instead of 0 if regulator_get failed.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
MCLKDIV bit of Register 04h Clocking1:
0 : Divide by 1
1 : Divide by 2
Thus in the case of freq <= 16500000, we should clear MCLKDIV bit.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
DACSLOPE bit of Register 06h ADC and DAC Control 2:
0: Normal mode
1: Sloping stop-band mode
Thus in the case of normal mode, we should clear DACSLOPE bit.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
MX51 Babbage has an AT45DB321 SPI Flash connected to eCSPI1.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Code called from an initcall can be maybe called for
machines it's not intended for. So check for valid
machines and return gracefully if an incompatible machine
is found.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Code called from an initcall can be maybe called for
machines it's not intended for. So check for valid
machines and return gracefully if an incompatible machine
is found.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Code called from an initcall can be maybe called for
machines it's not intended for. So check for valid
machines and return gracefully if an incompatible machine
is found.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds a Kconfig option for the avic irq controller
and lets the SoCs that need it select this option.
Also, as we have two irq controllers for i.MX, irq.c is not
appropriate anymore, so rename it to avic.c
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
PHYS_OFFSET may become a variable once the runtime PHYS_OFFSET
patch is merged, so use MX51_PHYS_OFFSET for boot_params.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Commit "ARM: i.MX IOMUX-V3 replace struct pad_desc with bitmapped cookie"
(b705cb4d42e95a4a43a8945571c8613e71526c3d) introduced a typo which was
preventing my efikamx to boot. This patch is fixing that.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The efikamx board is using a gpio to reset the board so add support
for it
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
On efikamx, uboot is stored on a nor spi flash. Add support for it
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds support for power key button of the efika mx. It's connected
on GPIO 2 31.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The efika mx a 3 leds (1 blue, 1 red, 1 green) connected on GPIOS 3 13/14/15.
Also, some special care is done for default trigger of blue led for mmc as
the mmc host used is different between hw revisions
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The efika mx is using a esdhc host for mmc support. Now that the sdhci
has support for it, enable it.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- add definition to configure pads as ESDHC{1,2} WP and CD
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- ALT0 is used to set GPIO mode of GPIO_1_{2,3,4,5,6,7,8,9} but it's ALT1
for GPIO_1_{0,1}.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
read board id value from the GPIO3_16/17/11
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
On the mx31_3ds board the touchscreen feature is provided by MC13783 PMIC.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The following patch is a first step to convert the 'struct pad_desc'
to a bitmapped cookie to facilitate adding platform specific pullup or
drive strength definitions to existing pad definitions without need to
rewrite the complete pad def.
The patch wraps 'struct pad_desc' in an opaque data type and
introduces macros to access the individual members.
This patch does not constitute any functional change!
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The file is not needed.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
