HDMI/DP codec on SKL/BSW is in the power well.
The power well must be turned on before probing the
HDMI/DP codec.
This is a temporary patch, which will power on the
powerwell by adding AZX_DCAPS_I915_POWERWELL for SKL
and BSW. After restructuring and new flag is added,
this patch will be reverted.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On CHV, PUNIT team confirmed that 'VLV_GFX_CLK_STATUS_BIT' is not a
sticky bit and it will always be set. So ignore Check for previous
Gfx force off during suspend and allow the force clk as part S0ix
Sequence
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Some BIOSes (e.g. the one on the Minnowboard) don't save/restore this
reg. If it's unlocked, we can just restore the previous value, and if
it's locked (in case the BIOS re-programmed it for us) the write will be
ignored and we'll still have "did it move" sanity check in the PM code to
warn us if something is still amiss.
References: https://bugs.freedesktop.org/show_bug.cgi?id=89611
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Darren Hart <dvhart@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
If the connect request from userspace didn't include an extended
capabilities IE, create one using the driver capabilities. This
fixes VHT associations, since those need to set the operating mode
notification capability.
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As the next patch will require the IE splitting utility functions
in cfg80211, move them there from mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It is best to use the physical reset if it is available. This patch adds
support for a GPIO controlled physical reset for the chip.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Although the SPFI BITCLK divider supports a value of up to 255, only
values up to 128 are usable. This results in a maximum possible bit
clock rate of 1/4th the input clock rate.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation for switching to using the SPI core's CS GPIO handling,
move setup of the PORT_STATE register, which must be configured before
CS is asserted, to a prepare_message() callback.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Removes some functions that are not used anywhere:
s5p_jpeg_input_raw_y16() s5p_jpeg_timer_disable() s5p_jpeg_timer_enable().
This was partially found by using a static code analysis program called
cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
JPEG codecs on Exynos4 and Exynos3250 SoCs utilize different number
of planes for storing the raw image data, depending on the format
of the image being processed. For the unused planes a random data
was being written to the related registers. Regardless of the fact
that this seemed not to be harmful, fix the issue for clarity reasons.
Reported-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
JPEG IP found in Exynos5420 is similar to what is in Exynos3250, but
there are some subtle differences which this patch takes into account.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove target from Makefile: this driver no longer exists.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Passing &mcasp->ruledata[dir] to snd_pcm_hw_rule_add() is not correct since
commit:
7b3d165a28 ASoC: davinci-mcasp: Index ruledata in drvdata with substream->stream
now sets up the struct based on the substream->stream (0 or 1) while we pass
a pointer which we take with dir (1 or 2). This will lead kernel crash.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since we have required at least GCC v3.2 for some time now, we
can drop the special handling of the 'gcc[0-9]_compiled.' label
which is not emitted anymore since GCC v3.0.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Michal Marek <mmarek@suse.cz>
When linking large kernels on ARM, the linker will insert veneers
(i.e., PLT like stubs) when function symbols are out of reach for
the ordinary relative branch/branch-and-link instructions.
However, due to the fact that the kallsyms region sits in .rodata,
which is between .text and .init.text, additional veneers may be
emitted in the second pass due to the fact that the size of the
kallsyms region itself has pushed the .init.text section further
apart, requiring even more veneers.
So ignore the veneers when generating the symbol table. Veneers
have no corresponding source code, and they will not turn up in
backtraces anyway.
This patch also lightly refactors the symbol_valid() function
to use a local 'sym_name' rather than the obfuscated 'sym + 1'
and 'sym + offset'
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Add missing terminating newlines to nfc_info and nfc_err
to avoid possible interleaving from other messages.
Miscellanea:
o typo fix of "unknonwn" in message
o remove unnecessary OOM messages as there's a generic dump_stack()
o realign arguments
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds support for the AmLogic Meson8b SoC.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the compatible string for Meson8b in Meson pinctrl documentation
and add new information for Meson8b in source code comments.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch introduces a new PIN macro and few small modifications to
simplify and shorten the Meson pinctrl drivers and cleanup the support
file for the AmLogic Meson8 SoC.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This cleanup is prepare to move the driver to drivers/gpio. Custom
definitions of gpio_get_value()/gpio_set_value() are dropped.
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use endian agnostic _relaxed IO accessors instead of the __raw ones.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We want those fixes (iio primarily) into the -next branch to help with
merge and testing issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The callers of setbat() are actually passing a pgprot_t for the flags
parameter. This doesn't matter unless STRICT_MM_TYPECHECKS is enabled.
So we can turn that on without breaking the build, change setbat() to
take a pgprot_t and have it convert it to an unsigned long internally.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The celleb code has seen no actual development for ~7 years.
We (maintainers) have no access to test hardware, and it is highly
likely the code has bit-rotted.
As far as we're aware the hardware was never widely available, and is
certainly no longer available, and no one on the list has shown any
interest in it over the years.
So remove it. If anyone has one and cares please speak up.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
The powernv code has some conditional support for running on bare metal
machines that have no OPAL firmware, but provide RTAS.
No released machines ever supported that, and even in the lab it was
just a transitional hack in the days when OPAL was still being
developed.
So remove the code.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Stewart Smith <stewart@linux.vnet.ibm.com>
When the kernel deleted a vti6 interface, this interface was not removed from
the tunnels list. Thus, when the ip6_vti module was removed, this old interface
was found and the kernel tried to delete it again. This was leading to a kernel
panic.
Fixes: 61220ab349 ("vti6: Enable namespace changing")
Signed-off-by: Yao Xiwei <xiwei.yao@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
https://bugzilla.kernel.org/show_bug.cgi?id=95211
Commit 70be6c91c8
("xfrm: Add xfrm_tunnel_skb_cb to the skb common buffer") added check
which dereferences ->outer_mode too early but larval SAs don't have
this pointer set (yet). So check for tunnel stuff later.
Mike Noordermeer reported this bug and patiently applied all the debugging.
Technically this is remote-oops-in-interrupt-context type of thing.
BUG: unable to handle kernel NULL pointer dereference at 0000000000000034
IP: [<ffffffff8150dca2>] xfrm_input+0x3c2/0x5a0
...
[<ffffffff81500fc6>] ? xfrm4_esp_rcv+0x36/0x70
[<ffffffff814acc9a>] ? ip_local_deliver_finish+0x9a/0x200
[<ffffffff81471b83>] ? __netif_receive_skb_core+0x6f3/0x8f0
...
RIP [<ffffffff8150dca2>] xfrm_input+0x3c2/0x5a0
Kernel panic - not syncing: Fatal exception in interrupt
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Freescale updates from Scott:
"Highlights include BMan device tree nodes, an MSI erratum workaround, a
couple minor performance improvements, config updates, and misc
fixes/cleanup."
Conflicts:
drivers/net/ethernet/mellanox/mlx4/cmd.c
net/core/fib_rules.c
net/ipv4/fib_frontend.c
The fib_rules.c and fib_frontend.c conflicts were locking adjustments
in 'net' overlapping addition and removal of code in 'net-next'.
The mlx4 conflict was a bug fix in 'net' happening in the same
place a constant was being replaced with a more suitable macro.
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we can safely increase the avtab max buckets without
triggering high order allocations and have a hash function that
will make better use of the larger number of buckets, increase
the max buckets to 2^16.
Original:
101421 entries and 2048/2048 buckets used, longest chain length 374
With new hash function:
101421 entries and 2048/2048 buckets used, longest chain length 81
With increased max buckets:
101421 entries and 31078/32768 buckets used, longest chain length 12
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Paul Moore <pmoore@redhat.com>
This function, based on murmurhash3, has much better distribution than
the original. Using the current default of 2048 buckets, there are many
fewer collisions:
Before:
101421 entries and 2048/2048 buckets used, longest chain length 374
After:
101421 entries and 2048/2048 buckets used, longest chain length 81
The difference becomes much more significant when buckets are increased.
A naive attempt to expand the current function to larger outputs doesn't
yield any significant improvement; so this function is a prerequisite
for increasing the bucket size.
sds: Adapted from the original patches for libsepol to the kernel.
Signed-off-by: John Brooks <john.brooks@jolla.com>
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Paul Moore <pmoore@redhat.com>
Previously we shrank the avtab max hash buckets to avoid
high order memory allocations, but this causes avtab lookups to
degenerate to very long linear searches for the Fedora policy. Convert to
using a flex_array instead so that we can increase the buckets
without such limitations.
This change does not alter the max hash buckets; that is left to a
separate follow-on change.
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Paul Moore <pmoore@redhat.com>
Move the NetLabel secattr MLS category import logic into
mls_import_netlbl_cat() where it belongs, and use the
mls_import_netlbl_cat() function in security_netlbl_secattr_to_sid().
Reported-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Paul Moore <pmoore@redhat.com>
Commit f01e1af445 ("selinux: don't pass in NULL avd to avc_has_perm_noaudit")
made this pointer reassignment unnecessary. Avd should continue to reference
the stack-based copy.
Signed-off-by: Jeff Vander Stoep <jeffv@google.com>
Acked-by: Stephen Smalley <sds@tycho.nsa.gov>
[PM: tweaked subject line]
Signed-off-by: Paul Moore <pmoore@redhat.com>
Commit 84c91b7ae0 (PM / hibernate: avoid unsafe pages in e820 reserved
regions) is reported to make resume from hibernation on Lenovo x230
unreliable, so revert it.
We will revisit the issue the commit in question was supposed to fix
in the future.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=96111
Reported-by: rhn <kebuac.rhn@porcupinefactory.org>
Cc: 3.17+ <stable@vger.kernel.org> # 3.17+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On ASUS TP500LN and X750JN, the touchpad absolute mode is reset each
time set_rate is done.
In order to fix this, we will verify the firmware version, and if it
matches the one in those laptops, the set_rate function is overloaded
with a function elantech_set_rate_restore_reg_07 that performs the
set_rate with the original function, followed by a restore of reg_07
(the register that sets the absolute mode on elantech v4 hardware).
Also the ASUS TP500LN and X750JN firmware version, capabilities, and
button constellation is added to elantech.c
Cc: stable@vger.kernel.org
Reported-and-tested-by: George Moutsopoulos <gmoutso@yahoo.co.uk>
Signed-off-by: Ulrik De Bie <ulrik.debie-os@e2big.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull networking fixes from David Miller:
1) In TCP, don't register an FRTO for cumulatively ACK'd data that was
previously SACK'd, from Neal Cardwell.
2) Need to hold RNL mutex in ipv4 multicast code namespace cleanup,
from Cong WANG.
3) Similarly we have to hold RNL mutex for fib_rules_unregister(), also
from Cong WANG.
4) Revert and rework netns nsid allocation fix, from Nicolas Dichtel.
5) When we encapsulate for a tunnel device, skb->sk still points to the
user socket. So this leads to cases where we retraverse the
ipv4/ipv6 output path with skb->sk being of some other address
family (f.e. AF_PACKET). This can cause things to crash since the
ipv4 output path is dereferencing an AF_PACKET socket as if it were
an ipv4 one.
The short term fix for 'net' and -stable is to elide these socket
checks once we've entered an encapsulation sequence by testing
xmit_recursion.
Longer term we have a better solution wherein we pass the tunnel's
socket down through the output paths, but that is way too invasive
for 'net' and -stable.
From Hannes Frederic Sowa.
6) l2tp_init() failure path forgets to unregister per-net ops, from
Cong WANG.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net/mlx4_core: Fix error message deprecation for ConnectX-2 cards
net: dsa: fix filling routing table from OF description
l2tp: unregister l2tp_net_ops on failure path
mvneta: dont call mvneta_adjust_link() manually
ipv6: protect skb->sk accesses from recursive dereference inside the stack
netns: don't allocate an id for dead netns
Revert "netns: don't clear nsid too early on removal"
ip6mr: call del_timer_sync() in ip6mr_free_table()
net: move fib_rules_unregister() under rtnl lock
ipv4: take rtnl_lock and mark mrt table as freed on namespace cleanup
tcp: fix FRTO undo on cumulative ACK of SACKed range
xen-netfront: transmit fully GSO-sized packets
If we fail past the aio_setup_ring(), we need to destroy the
mapping. We don't need to care about anybody having found ctx,
or added requests to it, since the last failure exit is exactly
the failure to make ctx visible to lookups.
Reproducer (based on one by Joe Mario <jmario@redhat.com>):
void count(char *p)
{
char s[80];
printf("%s: ", p);
fflush(stdout);
sprintf(s, "/bin/cat /proc/%d/maps|/bin/fgrep -c '/[aio] (deleted)'", getpid());
system(s);
}
int main()
{
io_context_t *ctx;
int created, limit, i, destroyed;
FILE *f;
count("before");
if ((f = fopen("/proc/sys/fs/aio-max-nr", "r")) == NULL)
perror("opening aio-max-nr");
else if (fscanf(f, "%d", &limit) != 1)
fprintf(stderr, "can't parse aio-max-nr\n");
else if ((ctx = calloc(limit, sizeof(io_context_t))) == NULL)
perror("allocating aio_context_t array");
else {
for (i = 0, created = 0; i < limit; i++) {
if (io_setup(1000, ctx + created) == 0)
created++;
}
for (i = 0, destroyed = 0; i < created; i++)
if (io_destroy(ctx[i]) == 0)
destroyed++;
printf("created %d, failed %d, destroyed %d\n",
created, limit - created, destroyed);
count("after");
}
}
Found-by: Joe Mario <jmario@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
teach ->mremap() method to return an error and have it fail for
aio mappings in process of being killed
Note that in case of ->mremap() failure we need to undo move_page_tables()
we'd already done; we could call ->mremap() first, but then the failure of
move_page_tables() would require undoing whatever _successful_ ->mremap()
has done, which would be a lot more headache in general.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Commit 1daa4303b4 ("net/mlx4_core: Deprecate error message at
ConnectX-2 cards startup to debug") did the deprecation only for port 1
of the card. Need to deprecate for port 2 as well.
Fixes: 1daa4303b4 ("net/mlx4_core: Deprecate error message at ConnectX-2 cards startup to debug")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
