cpu and memory hotplug scripts use the same name. Change
cpu on-off-test.sh to cpu-on-off-test.sh.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yuval Mintz says:
====================
bnx2x: kdump related fixes
This patch series aims to fix bnx2x driver issues when loading in kdump kernel.
Both issues fixed here would be fatal to the device, requiring full reset of
the system in order to recover, preventing the device from serving its purpose
in the kdump environment.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When IOMM-vtd is active, once main kernel crashes unfinished DMAE transactions
will be blocked, putting the HW in an error state which will cause further
transactions to timeout.
Current employed logic uses wrong macros, causing the first function to be the
only function that cleanups that error state during its probe/load.
This patch allows all the functions to successfully re-load in kdump kernel.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running in a kdump kernel, it's very likely that due to sync. loss with
management firmware the first PCI function to probe and reach the previous
unload flow would decide it can reset the chip and continue onward. While doing
so, it will only close its own Rx port.
On a 4-port device where 2nd port on engine is a 1g-port, the 2nd port would
allow ingress traffic after the chip is reset [assuming it was active on the
first kernel]. This would later cause a HW attention.
This changes driver flow to close both ports' 1g capabilities during the
previous driver unload flow prior to the chip reset.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the ahci_st driver will hang the system on probe, as the
st_configure_oob function does some register writes before the IP
is clocked. This patch moves the function call to after
ahci_platform_enable_resources (which enables the IP clock), and
resolves the hang.
Addtionally st_ahci_configure_oob should be called in the st_ahci_resume
function, so we also rectify that ensuring it is also called after
the IP clock has been enabled.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
As part of testing ahci_st driver working on stih407 I noticed
several things wrong in the DT documentation: -
1) Compatible string doesn't match the driver code
2) pwr-rst reset isn't documented (but exists in the driver)
3) some whitespace issues (spaces not tabs)
Also add in a stih407 family example into the doc.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The example is wrong in that the phys property should take a
phandle to the phy port.
Also with the changing over to generic PHY type constants we also
update that as well.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch marks functions llog_cat_set_first_idx and cat_cancel_cb
static as these are used only within this file. Also since cat_cancel_cb
is made static do not export it.
This eliminates the following sparse warning:
warning: symbol * was not declared. Should it be static?
Signed-off-by: Darshana Padmadas <darshanapadmadas@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch makes functions mgc_logname2resid, mgc_set_info_async
and mgc_init static as these are only used internally.
This also eliminates sparse warnings of the type:
warning: symbol * was not declared. Should it be static?
Signed-off-by: Darshana Padmadas <darshanapadmadas@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch includes the header file mdc_internal.h that declares the
function lprocfs_mdc_init_vars.
This also eliminates the sparse warning:
warning: symbol 'lprocfs_mdc_init_vars' was not declared. Should it be static?
Signed-off-by: Darshana Padmadas <darshanapadmadas@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch includes the header lustre/include/lclient.h that declares
the functions lov_lsm_put and lov_read_and_clear_async_rc defined in
lov_object.c.
This eliminates warnings reported by sparse:
warning: symbol was not declared. Should it be static?
Signed-off-by: Darshana Padmadas <darshanapadmadas@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch includes the header file lmv_internal.h that declares
the function lprocfs_lmv_init_vars defined in lproc_lmv.c.
This eliminates the sparse warning:
warning: symbol 'lprocfs_lmv_init_vars' was not declared. Should it be static?
Signed-off-by: Darshana Padmadas <darshanapadmadas@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function obd_proc_version_seq_show is only used in this
file, so make it static.
This eliminates the following sparse warning:
warning: symbol 'obd_proc_version_seq_show' was not declared. Should it be static?
Signed-off-by: Darshana Padmadas <darshanapadmadas@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Handle VERSION Rx protocol packets. We should respond to a VERSION packet
with a string indicating the Rx version. This is a maximum of 64 characters
and is padded out to 65 chars with NUL bytes.
Note that other AFS clients use the version request as a NAT keepalive so we
need to handle it rather than returning an abort.
The standard formulation seems to be:
<project> <version> built <yyyy>-<mm>-<dd>
for example:
" OpenAFS 1.6.2 built 2013-05-07 "
(note the three extra spaces) as obtained with:
rxdebug grand.mit.edu -version
from the openafs package.
Signed-off-by: David Howells <dhowells@redhat.com>
Sparse reported the following warnings:
warning: symbol 'lstcon_console_init' was not declared. Should it be static?
warning: symbol 'lstcon_console_fini' was not declared. Should it be static?
warning: symbol 'lstcon_ioctl_entry' was not declared. Should it be static?
However since these functions are used in other files,
they cannot be made static, so add protoypes for the same in console.h.
Signed-off-by: Darshana Padmadas <darshanapadmadas@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Delete duplicated argument to | for the state argument in
the _clr_fwstate_() function call as it is redundant.
Detected with coccinelle.
Signed-off-by: Cristina Opriceana <cristina.opriceana@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use memdup_user() to avoid its duplicated implementation and simplify
code. memdup_user() uses GFP_KERNEL instead of GFP_ATOMIC,
which is valid because copy_from_user() might sleep and it's useless
to make the allocation atomic. Found with coccinelle.
Signed-off-by: Cristina Opriceana <cristina.opriceana@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Place driver on standby mode on error in order to prevent wasting
power. Move standby function above to be seen by the new call.
Signed-off-by: Cristina Opriceana <cristina.opriceana@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes explicit NULL comparison and writes it in its
shorter form. Detected with coccinelle.
Signed-off-by: Cristina Opriceana <cristina.opriceana@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes explicit NULL comparison and replaces it with
its shorter form. Detected with coccinelle.
Signed-off-by: Cristina Opriceana <cristina.opriceana@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes explicit NULL comparison and replaces it
with its shorter form. Detected with coccinelle.
Signed-off-by: Cristina Opriceana <cristina.opriceana@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch checks if an error occurred on probe and stops the
device in order to avoid wasting power.
Signed-off-by: Cristina Opriceana <cristina.opriceana@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This add south-bridge (SB700/SB710/SB800 chipset) ACPI platform driver
for Loongson-3. This will be used by EC (Embedded Controller, used by
laptops) driver and STR (Suspend To RAM).
[ralf@linux-mips.org: Fix build error if !CONFIG_CPU_LOONGSON3. Build
doesn't like it if no obj-* variable is defined at all in a Makefile.
Obviously this has not been tested on other platforms.]
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/9619/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On SGI Origin 2k/Onyx2 and SGI Octane systems, there can exist multiple PCI
buses attached to the Xtalk bus. The current code will stop counting PCI buses
after it finds the first one. If one installs the optional PCI cardcage
("shoebox") into these systems, because of the order of the Xtalk widgets, the
current PCI code will find the cardcage first, and fail to detect the BaseIO
PCI devices, which are on a higher Xtalk widget ID.
This patch adds the hooks needed for resolving this issue in the IP27 PCI code
(in a later patch).
Verified on both an SGI Onyx2 and an SGI Octane.
Signed-off-by: Joshua Kinard <kumba@gentoo.org>
Cc: Linux MIPS List <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/9074/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When hardware checksum generation is switched on the checksum
generation was only being signalled to the hardware correctly
in Big Endian mode.
Signed-off-by: Paul Martin <paul.martin@codethink.co.uk>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9634/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The octeon crypto co-processor expects values to be big endian.
Wrap the data transfers with cpu_to_be64() and be64_to_cpu()
transformations.
This passes for all the MD5 test vectors in crypto/testmgr.h
Signed-off-by: Paul Martin <paul.martin@codethink.co.uk>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9631/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
64 bit access is unaffected but for 32 bit access, swap high and
low words. Similarly for 16 bit access, reverse the order of the
four possible words, and for 8 bit access reverse the order of byte
accesses.
Signed-off-by: Paul Martin <paul.martin@codethink.co.uk>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9630/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Although the proper way to do this for bitfields would be to use
the macro that Ralf has provided, this is a little easier to
understand as a diff.
Signed-off-by: Paul Martin <paul.martin@codethink.co.uk>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9628/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This allows the kernel to correctly detect an R16000 MIPS CPU on systems that
have those. Otherwise, such systems will detect the CPU as an R14000, due to
similarities in the CPU PRId value.
Signed-off-by: Joshua Kinard <kumba@gentoo.org>
Cc: Linux MIPS List <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/9092/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As an alternative to the "clock-frequency" property, allow the GIC
timer operating clock to be specified in the device-tree instead.
This is useful on systems which use common clock or where the GIC
is not fixed to a particular frequency and is instead, for example,
derived from the CPU clock.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9309/
Computing sum introduces true data dependency. This patch removes some
true data depdendencies, hence increases instruction level parallelism.
This patch brings up to 50% csum performance gain on Loongson 3a.
One example about how this patch works is in CSUM_BIGCHUNK1:
// ** original ** vs ** patch applied **
ADDC(sum, t0) ADDC(t0, t1)
ADDC(sum, t1) ADDC(t2, t3)
ADDC(sum, t2) ADDC(sum, t0)
ADDC(sum, t3) ADDC(sum, t2)
In the original implementation, each ADDC(sum, ...) depends on the sum
value updated by previous ADDC(as source operand).
With this patch applied, the first two ADDC operations are independent,
hence can be executed simultaneously if possible.
Another example is in the "copy and sum calculating chunk":
// ** original ** vs ** patch applied **
STORE(t0, UNIT(0) ... STORE(t0, UNIT(0) ...
ADDC(sum, t0) ADDC(t0, t1)
STORE(t1, UNIT(1) ... STORE(t1, UNIT(1) ...
ADDC(sum, t1) ADDC(sum, t0)
STORE(t2, UNIT(2) ... STORE(t2, UNIT(2) ...
ADDC(sum, t2) ADDC(t2, t3)
STORE(t3, UNIT(3) ... STORE(t3, UNIT(3) ...
ADDC(sum, t3) ADDC(sum, t2)
With this patch applied, ADDC and the **next next** ADDC are independent.
Signed-off-by: chenj <chenj@lemote.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9608/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
DSR-1000N board has two GPIO LEDs next to USB ports. Add support for them.
[ralf@linux-mips.org: Resolved conflict due to the moving of the DTS files
into vendor subdirectories.]
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9624/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch has no functional changes, it just to keep the assembler
code to a minimum. Files and functions naming is borrowed from X86.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/9616/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We found that TLB mismatch not only happens after kernel resume, but
also happens during snapshot restore. So move it to the beginning of
swsusp_arch_suspend().
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: <stable@vger.kernel.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: stable@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9621/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
With no I2C driver available, keeping the platform device registration
makes no sense just as keeping the code to instantiage the I2C devices.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
