This driver will set RT5645_DEPOP_MAN bit in headphone power up
depop process. We need to restore it in headphone power down
process. Otherwise, we will get headphone noise when push button
function is enabled.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In codec bias level off, we need to disable gate mode with MCLK
for power saving. It is set by one bit. We don't need to write
while register for that.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
RT5645 doesn't support auto incrementing writes so driver should set
the use_single_rw flag for regmap.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rt5650 and rt5645 use different register bits for format configuration.
This patch modifies rt5645_hw_params and rt5645_set_dai_fmt to support
both codecs.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The WM8741 DAC supports the following typical audio sampling rates:
44.1kHz, 88.2kHz, 176.4kHz (eg: with a master clock of 22.5792MHz)
32kHz, 48kHz, 96kHz, 192kHz (eg: with a master clock of 24.576MHz)
For the rates lists, we should use 82000 instead of 88235, 176400
instead of 1764000 and 192000 instead of 19200 (seems to be a typo).
Signed-off-by: Sergej Sawazki <ce3a@gmx.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
ak4642 has power-save mode for stereo line to reduce pop noise.
This patch enables it.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is worth to check the regmap_read result for ID check since it
is the first regmap_read. And we can check if there is any i2c
issue.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently GPIO4 is hardcoded to output the pll-lock signal.
Unfortunately this is after the pll-out GPIO is configured which
is selectable in the device tree. Therefore it is not possible to
use GPIO4 for pll-out. Therefore this patch removes the
configuration of GPIO4.
Signed-off-by: Howard Mitchell <hm@hmbedded.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
If den=1 and pllin_rate>20MHz then den and num are adjusted to 0
causing a divide by zero error a few lines further on. Therefore
this patch correctly scales num and den such that
pllin_rate/den < 20MHz as required in the device data sheet.
Signed-off-by: Howard Mitchell <hm@hmbedded.co.uk>
Signed-off-by: Mark Brown <broonie@sirena.org.uk>
Cc: stable@vger.kernel.org
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is to ensure that 'alsactl restore' does not apply default
initialisation as the chip reset defaults are preferred.
Signed-off-by: Howard Mitchell <hm@hmbedded.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Constify local structures (snd_soc_dai_ops, snd_soc_codec_driver,
regmap_config) and array (reg_defaults) which are not modified by the
driver and passed to core as pointer to const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It needs DAC -> Playback route instead of direct settings via
SND_SOC_DAPM_DAC. otherwise, it can't find correct path if
sound card used prefix name
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The default value for the bias_level is SND_SOC_BIAS_OFF when probe is being
called, there is no need to initialize it explicitly.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The default value for the bias_level is SND_SOC_BIAS_OFF when probe is being
called, there is no need to initialize it explicitly.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Enable WM8731 to support common clock framework.
Signed-off-by: Songjun Wu <songjun.wu@atmel.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch defines an API to select the clock source for specified filters.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove adc stereo2 filter since it is not in rt5645/rt5650 codec.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rt5650 and rt5645 use different register bits for TDM configuration.
This patch modifies rt5645_set_tdm_slot to support both codecs.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
type T;
identifier f;
@@
static T f (...) { ... }
@@
identifier r.f;
declarer name EXPORT_SYMBOL_GPL;
@@
-EXPORT_SYMBOL_GPL(f);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
We force enable "Mic Det Power" when a jack is inserted. Also, we
set codec idle_bias_off = true. As a result, codec driver will not
suspend as we expect.
On Braswell, we don't need the jack detection when suspend but need
it after resume, so export the jack suspend/resume APIs which are
provided for machine driver to control during suspend/resume.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Jin Yao <yao.jin@linux.intel.com>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds the IRQ function support of rt5670. We use a flag
named dev_gpio in platform data to inform codec driver if the IRQ
function is used or not. Also, we export rt5670_set_jack_detect
for machine driver to pass the jack point.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
Even if bus is not hot-pluggable, the devices can be unbound from the
driver via sysfs, so we should not be using __exit annotations on
remove() methods. The only exception is drivers registered with
platform_driver_probe() which specifically disables sysfs bind/unbind
attributes.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Even if bus is not hot-pluggable, the devices can be unbound from the
driver via sysfs, so we should not be using __exit annotations on
remove() methods. The only exception is drivers registered with
platform_driver_probe() which specifically disables sysfs bind/unbind
attributes.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
return type of wait_for_completion_timeout is unsigned long not int. An
appropriately named unsigned long is added and the assignment fixed up.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
return type of wait_for_completion_timeout is unsigned long not int. An
appropriately named unsigned long is added and the assignment fixed up.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
return type of wait_for_completion_timeout is unsigned long not int. An
appropriately named unsigned long is added and the assignment fixed up.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
