Commit dff173de84 ("bnx2x: Fix statistics locking scheme") changed the
bnx2x locking around statistics state into using a mutex - but the lock
is being accessed via a timer which is forbidden.
[If compiled with CONFIG_DEBUG_MUTEXES, logs show a warning about
accessing the mutex in interrupt context]
This moves the implementation into using a semaphore [with size '1']
instead.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 12a8541d5c "bnx2x: Delay during kdump load" added a 5 seconds
delay to bnx2x's probe function in the kdump case to let the firmware
realize the old driver is gone.
The problem with the delay is that it is per-device, so if you have
several bnx2x NICs in NPAR mode, the delays can accumulate to minutes.
Fix it by adjusting the delay so that we do not wait more than
necessary, i.e. no more delaying after 5 seconds of kernel boot time.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a kdump environment interfaces might be re-loaded without a proper
unload sequence in the previous running kernel.
bnx2x management FW and driver maintains a `pulse' that notifies the FW
that the driver is still up and running.
Driver load on the kdump kernel should be performed only after the pulse
has been out-of-sync long enough for the management FW to identify that
the driver has crashed, on which point it will perform some necessary
cleanup of the HW.
In today's distros kdump loading is quite fast, sometimes too fast for our
FW to get out-of-sync. This patch delays the bnx2x's probe during kdump
to allow a proper re-load on the kdump kernel.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These flags are redundant with dev->features. Remove them.
Just make sure to set dev->features ourselves in bnx2x_set_features()
before performing the reload of the card.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is simpler to have the TPA mode as one three-state variable.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If disable_tpa is set, remove NETIF_F_LRO from hw_features, so ethtool sees
it as "off [fixed]".
Note that setting the NETIF_F_LRO bit in dev->features in the 'else'
branch is not needed, because the bit was already set by
bnx2x_init_dev().
Then the check for disable_tpa in in bnx2x_fix_features() becomes unnecessary.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/asix_common.c
drivers/net/usb/sr9800.c
drivers/net/usb/usbnet.c
include/linux/usb/usbnet.h
net/ipv4/tcp_ipv4.c
net/ipv6/tcp_ipv6.c
The TCP conflicts were overlapping changes. In 'net' we added a
READ_ONCE() to the socket cached RX route read, whilst in 'net-next'
Eric Dumazet touched the surrounding code dealing with how mini
sockets are handled.
With USB, it's a case of the same bug fix first going into net-next
and then I cherry picked it back into net.
Signed-off-by: David S. Miller <davem@davemloft.net>
When IOMM-vtd is active, once main kernel crashes unfinished DMAE transactions
will be blocked, putting the HW in an error state which will cause further
transactions to timeout.
Current employed logic uses wrong macros, causing the first function to be the
only function that cleanups that error state during its probe/load.
This patch allows all the functions to successfully re-load in kdump kernel.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running in a kdump kernel, it's very likely that due to sync. loss with
management firmware the first PCI function to probe and reach the previous
unload flow would decide it can reset the chip and continue onward. While doing
so, it will only close its own Rx port.
On a 4-port device where 2nd port on engine is a 1g-port, the 2nd port would
allow ingress traffic after the chip is reset [assuming it was active on the
first kernel]. This would later cause a HW attention.
This changes driver flow to close both ports' 1g capabilities during the
previous driver unload flow prior to the chip reset.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the driver to use ns_to_timespec64() and
timespec64_to_ns() instead of open coding the same logic.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use bool constants as the return values instead of 1 and 0.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's possible that due to errors [either on PCI or on device itself]
registers reads would fail, returning all-Fs.
This adds a check as early as possible so that driver will not read junk
values and make incorrect probe decisions according to them; instead,
gracefully fail the probe.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver's clock is implemented using a timecounter, and so with
this patch the driver is ready for the year 2038.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To allow drivers to handle the features check for multiple tags,
move the check to ndo_features_check().
As no drivers currently handle multiple tagged TSO, introduce
dflt_features_check() and call it if the driver does not have
ndo_features_check().
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Statistics' state-machine in bnx2x driver must be synced with various driver
flows, but its current locking scheme manages to be wasteful [using 2 locks +
additional local variable] and prone to race-conditions at the same time,
as the state-machine and 'action' are being accessed under different locks.
In addition, current 'safe exec' isn't in fact safe, since the only guarantee
it gives is that DMA transactions are over, but ramrods might still be running.
This patch cleans up said logic, leaving us with a single lock for the entire
flow and removing the possible races.
Changes from v2:
- Switched into mutex locking from semaphore locking.
- Release locks on error flows.
Changes from v1:
Failure to acquire lock fails flow instead of printing a warning and
allowing access to the critical section.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/emulex/benet/be_main.c
net/core/sysctl_net_core.c
net/ipv4/inet_diag.c
The be_main.c conflict resolution was really tricky. The conflict
hunks generated by GIT were very unhelpful, to say the least. It
split functions in half and moved them around, when the real actual
conflict only existed solely inside of one function, that being
be_map_pci_bars().
So instead, to resolve this, I checked out be_main.c from the top
of net-next, then I applied the be_main.c changes from 'net' since
the last time I merged. And this worked beautifully.
The inet_diag.c and sysctl_net_core.c conflicts were simple
overlapping changes, and were easily to resolve.
Signed-off-by: David S. Miller <davem@davemloft.net>
E1x chips (57710, 57711(E)) have no support for encapsulation
offload. bnx2x incorrectly advertises the support as available.
Setting of those features is conditional on "!CHIP_IS_E1x(bp)", but
the bp struct is not initialized yet at this point and consequently
any chip passes the check.
The check must use the "chip_is_e1x" local variable instead to work
correctly.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/cadence/macb.c
Overlapping changes in macb driver, mostly fixes and cleanups
in 'net' overlapping with the integration of at91_ether into
macb in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
EEH recovery for bnx2x based adapters is not reliable on all Power
systems using the default hot reset, which can result in an
unrecoverable EEH error. Forcing the use of fundamental reset
during EEH recovery fixes this.
Cc: stable<stable@vger.kernel.org>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the built-in function instead of memset.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
this patch fixes following sparse warnings:
bnx2x_main.c:9172:6: warning: symbol 'bnx2x_stop_ptp' was not declared. Should it be static?
bnx2x_main.c:13321:6: warning: symbol 'bnx2x_register_phc' was not declared. Should it be static?
bnx2x_main.c:14638:5: warning: symbol 'bnx2x_enable_ptp_packets' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the driver to use the new and improved method
for adjusting the offset of a timecounter.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GSO isn't the only offload feature with restrictions that
potentially can't be expressed with the current features mechanism.
Checksum is another although it's a general issue that could in
theory apply to anything. Even if it may be possible to
implement these restrictions in other ways, it can result in
duplicate code or inefficient per-packet behavior.
This generalizes ndo_gso_check so that drivers can remove any
features that don't make sense for a given packet, similar to
netif_skb_features(). It also converts existing driver
restrictions to the new format, completing the work that was
done to support tunnel protocols since the issues apply to
checksums as well.
By actually removing features from the set that are used to do
offloading, it solves another problem with the existing
interface. In these cases, GSO would run with the original set
of features and not do anything because it appears that
segmentation is not required.
CC: Tom Herbert <therbert@google.com>
CC: Joe Stringer <joestringer@nicira.com>
CC: Eric Dumazet <edumazet@google.com>
CC: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Acked-by: Tom Herbert <therbert@google.com>
Fixes: 04ffcb255f ("net: Add ndo_gso_check")
Tested-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/amd/xgbe/xgbe-desc.c
drivers/net/ethernet/renesas/sh_eth.c
Overlapping changes in both conflict cases.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use vxlan_gso_check() to advertise offload support for this NIC.
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our FW can support several fastpath HSI [for backward compatibility] but up
until now VFs were always configured to use latest fastpath HSI [although VF
driver might be older and use an older fastpath HSI].
For linux drivers, the differences are insignificant since driver never
utilized features that were overridden by the HSI change. But for VMs running
other operating systems this might be a problem.
In addition, eventually FW might change fastpath HSI in such a manner that
backward compatibility WILL break unless configured with proper version.
This patch fixes the issue for other operating system VMs, as well as lays
the ground work for forward compatibility in regard to the fastpath HSI.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So this can be reused for identification of other "items" as well.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Reviewed-by: Thomas Graf <tgraf@suug.ch>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x_msix_fp_int() and bnx2x_interrupt() run from hard interrupt
context.
They can use napi_schedule_irqoff() instead of napi_schedule()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ariel Elior <ariel.elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using new Multi-function modes it's possible that due to incompatible
configuration management FW will fallback into an existing mode.
Notice that at the moment this fallback is exactly the same as the already
existing switch-independent multi-function mode, but we still use existing
infrastructure to hold this information [in case some small differences will
arise in the future].
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Dmitry Kravkov <Dmitry.Kravkov@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for a new multi-function mode based on the Unified Fabric Port
system specifications.
Support includes configuration of:
1. Outer vlan tags.
2. Bandwidth settings.
3. Virtual link enable/disable.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Dmitry Kravkov <Dmitry.Kravkov@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rearrange macros to query for storage-only modes in different MF environment.
Improves the readibility and maintainability of the code. E.g.:
- if (IS_MF_STORAGE_SD(bp) || IS_MF_FCOE_AFEX(bp))
+ if (IS_MF_STORAGE_ONLY(bp))
In addition, this removes the need for bnx2x_is_valid_ether_addr().
Signed-off-by: Dmitry Kravkov <Dmitry.Kravkov@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some hosts can be both little and big endian.
In certain scenarios a big endian kernel can kexec a little endian kernel.
This patch fixes this case from both ends:
1) Return endianity to original values on shutdown (in case little endian kernel boots after we shutdown).
2) Do not rely on HW reset values when loading driver in little endian kernel
but configure them explicitly (in case previous kernel was big endian and did not reset the HW).
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Incorrect checking of array instead of array contents in panic_dump
flow - results of commit e261199872 ("bnx2x: Safe bnx2x_panic_dump()").
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When STOP_ON_ERROR is set driver will not compile. Even if it did,
traffic will not pass without this patch as several fields which are
verified by FW/HW on the Tx path are not properly set.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use is_kdump_kernel() to detect kdump kernel, instead of
reset_devices.
CC: Ariel Elior <ariel.elior@qlogic.com>
CC: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is mostly a semantic change which modifies the code parsing and printing
of FW asserts.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bnx2x panic dump spills a lot of information from the driver's
fastpath, but may be called while some of the fastpath is uninitialized.
This patch verifies that pointers are already allocated before dereferencing
them to prevent possible kernel panics.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch does several semantic things:
- Fixing typos.
- Removing unnecessary prints.
- Removing unused functions and definitions.
- Change 'strange' usage of boolean variables.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a PHC to the bnx2x driver. Driver supports timestamping send/receive
PTP packets, as well as adjusting the on-chip clock.
The driver has been tested with linuxptp project.
Signed-off-by: Michal Kalderon <Michal.Kalderon@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- (L2) In some multi-function configurations, inter-PF and inter-VF
Tx switching is incorrectly enabled.
- (L2) Wrong assert code in FLR final cleanup in case it is sent not
after FLR.
- (L2) Chip may stall in very rare cases under heavy traffic with FW GRO
enabled.
- (L2) VF malicious notification error fixes.
- (L2) Default gre tunnel to IPGRE which allows proper RSS for IPGRE packets,
L2GRE traffic will reach single queue.
- (FCoE) Fix data being placed in wrong buffer when corrupt FCoE frame is
received.
- (FCoE) Burst of FIP packets with destination MAC of ALL-FCF_MACs
causes FCoE traffic to stop.
Signed-off-by: Dmitry Kravkov <Dmitry.Kravkov@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 91ebb929b6 ("bnx2x: Add support for Multi-Function UNDI") [which was
later supposedly fixed by de682941ee ("bnx2x: Fix UNDI driver unload")]
introduced a bug in which in some [yet-to-be-determined] scenarios the
alternative flushing mechanism which was to guarantee the Rx buffers are
empty before resetting them during device probe will fail.
If this happens, when device will be loaded once more a fatal attention will
occur; Since this most likely happens in boot from SAN scenarios, the machine
will fail to load.
Notice this may occur not only in the 'Multi-Function' scenario but in the
regular scenario as well, i.e., this introduced a regression in the driver's
ability to perform boot from SAN.
The patch reverts the mechanism and applies the old scheme to multi-function
devices as well as to single-function devices.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines. This issue was reported by checkpatch.
A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@
- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;
// </smpl>
[bhelgaas: add semantic patch]
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Until now VFs were oblvious to the actual configured link parameters.
This patch does 2 things:
1. It enables a PF to inform its VF using the bulletin board of the link
configured, and allows the VF to present that information.
2. It adds support of `ndo_set_vf_link_state', allowing the hypervisor
to set the VF link state.
Signed-off-by: Dmitry Kravkov <Dmitry.Kravkov@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MSI-X should use PCI_MSIX_FLAGS not PCI_MSI_FLAGS.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Seccomp BPF filters can now be JIT'd, from Alexei Starovoitov.
2) Multiqueue support in xen-netback and xen-netfront, from Andrew J
Benniston.
3) Allow tweaking of aggregation settings in cdc_ncm driver, from Bjørn
Mork.
4) BPF now has a "random" opcode, from Chema Gonzalez.
5) Add more BPF documentation and improve test framework, from Daniel
Borkmann.
6) Support TCP fastopen over ipv6, from Daniel Lee.
7) Add software TSO helper functions and use them to support software
TSO in mvneta and mv643xx_eth drivers. From Ezequiel Garcia.
8) Support software TSO in fec driver too, from Nimrod Andy.
9) Add Broadcom SYSTEMPORT driver, from Florian Fainelli.
10) Handle broadcasts more gracefully over macvlan when there are large
numbers of interfaces configured, from Herbert Xu.
11) Allow more control over fwmark used for non-socket based responses,
from Lorenzo Colitti.
12) Do TCP congestion window limiting based upon measurements, from Neal
Cardwell.
13) Support busy polling in SCTP, from Neal Horman.
14) Allow RSS key to be configured via ethtool, from Venkata Duvvuru.
15) Bridge promisc mode handling improvements from Vlad Yasevich.
16) Don't use inetpeer entries to implement ID generation any more, it
performs poorly, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1522 commits)
rtnetlink: fix userspace API breakage for iproute2 < v3.9.0
tcp: fixing TLP's FIN recovery
net: fec: Add software TSO support
net: fec: Add Scatter/gather support
net: fec: Increase buffer descriptor entry number
net: fec: Factorize feature setting
net: fec: Enable IP header hardware checksum
net: fec: Factorize the .xmit transmit function
bridge: fix compile error when compiling without IPv6 support
bridge: fix smatch warning / potential null pointer dereference
via-rhine: fix full-duplex with autoneg disable
bnx2x: Enlarge the dorq threshold for VFs
bnx2x: Check for UNDI in uncommon branch
bnx2x: Fix 1G-baseT link
bnx2x: Fix link for KR with swapped polarity lane
sctp: Fix sk_ack_backlog wrap-around problem
net/core: Add VF link state control policy
net/fsl: xgmac_mdio is dependent on OF_MDIO
net/fsl: Make xgmac_mdio read error message useful
net_sched: drr: warn when qdisc is not work conserving
...
