The current iteration in get_dsi_id_from_intf() is wrong:
instead of iterating until hw_cfg->intf.count, we need to iterate
until MDP5_INTF_NUM_MAX here.
Let's take the example of msm8x16:
hw_cfg->intf.count = 1
intfs[0] = INTF_Disabled
intfs[1] = INTF_DSI
If we stop iterating once i reaches hw_cfg->intf.count (== 1),
we will miss the test for intfs[1].
Actually, this hw_cfg->intf.count entry is quite confusing and is not
(or *should not be*) used anywhere else; let's remove it.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
This change adds the support in mdp5 kms driver for single
and dual DSI. Dual DSI case depends on the framework API
and sequence change to support dual data path.
v1: Initial change
v2: Address Rob Clark's comment
- Separate command mode encoder to a new file mdp5_cmd_encoder.c
- Rebase to not depend on msm_drm_sub_dev change
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change is to make the content in construct_encoder reflect its
name.
Also, DSI connector may be connected to video mode or command mode
encoder, so that 2 different encoders need to be constructed for DSI.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
MDP block is actually contained inside the MDSS block. For some
chipsets, the base address of the MDP registers is different from the
current (assumed) 0x100 offset.
Like CTL and LM blocks, this changes introduce a dynamic offset
for the MDP instance, which can be found out at runtime, once the
MDSS HW version is read.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Up until now, we assume that eDP is tight to intf_0 and HDMI to
intf_3. This information shall actually come from the mdp5_cfg
module since it can change from one chip to another.
v2: rename macro to mdp5_cfg_intf_is_virtual() [pointed by Archit]
v3: add sanity check before writing in INTF_TIMING_ENGINE_EN registers
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
DSI and WB interfaces need a more complex pipeline configuration
than the current mdp5_ctl_set_intf().
For example, memory output connections need to be selected for
WB. Interface mode (Video vs. Command modes) also need to be
configured for DSI.
This change takes care of configuring the whole pipeline as far
as operation mode goes. DSI and WB interfaces will be added
later.
v2: rename macro to mdp5_cfg_intf_is_virtual() [pointed by Archit]
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
[Remove temp bisectability hack -Rob]
Signed-off-by: Rob Clark <robdclark@gmail.com>
Modified the hard-coded hdmi connector/encoder implementations in msm drm
driver to support both edp and hdmi.
V1: Initial change
V2: Address Thierry's change
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
As a result of atomic DPMS support, the various prepare/commit hooks get
called in a way that msm dislikes. We were expecting prepare/commit to
bracket a modeset, which is no longer the case. This was needed to hold
various extra clk's (such as interface clks) on while we are touching
registers, and in the case of mdp4 holding vblank enabled.
The most straightforward way to deal with this, since we already have
our own atomic_commit(), is to just handle prepare/commit internally to
the driver (with some additional vfuncs for mdp4 vs mdp5), and switch
everything over to instead use the new enable/disable hooks. It doesn't
really change too much, despite the code motion. What used to be in the
encoder/crtc dpms() fxns is split out into enable/disable.
We should be able to drop our own enable-state tracking, as the atomic
helpers should do this for us. But keeping that for the short term for
extra debugging as atomic stablizes.
Signed-off-by: Rob Clark <robdclark@gmail.com>
If crtc <-> encoder linkage changes, we could end up with the CRTC
listening for the wrong error or vsync irqs. Generally this problem
would correct itself relatively quickly, since we update the global
irqmask after dispatching irqs, but to be sure let the CRTC trigger
update_irq().
Signed-off-by: Rob Clark <robdclark@gmail.com>
For example, use 'struct mdp5_smp *' everywhere instead of 'void *', but
only declare it as 'struct mdp5_smp;' in common headers, so the struct
body is still private. The accomplishes the desired modularity while
still letting the compiler provide some type checking for us.
Signed-off-by: Rob Clark <robdclark@gmail.com>
MDP5 currently support one single CRTC with its private pipe.
This change allows the configuration of multiple CRTCs with
the possibility to attach several public planes to these CRTCs.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The hardware configuration modification from a version to another
is quite consequent. Introducing a configuration module
(mdp5_cfg) may make things more clear and easier to access when a
new hardware version comes up.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The Shared Memory Pool (SMP) has its own limitation, features and
state. Some examples are:
- the number of Memory Macro Block (MMB) and their size
- the number of lines that can be fetched
- the state of MMB currently allocated
- the computation of number of blocks required per plane
- client IDs ...
In order to avoid private data to be overwritten by other modules,
let's make these private to the SMP module.
Some of these depend on the hardware configuration, let's add them
to the mdp5_config struct.
In some hw configurations, some MMBs are statically tied to RGB
pipes and cannot be re-allocated dynamically. This change
introduces the concept of MMB static usage and makes sure that
dynamic MMB requests are dimensioned accordingly.
A note on passing a pipe pointer, instead of client IDs:
Client IDs are SMP-related information. Passing PIPE information
to SMP lets SMP module to find out which SMP client(s) are used.
This allows the SMP module to access the PIPE pointer, which can
be used for FIFO watermark configuration.
By the way, even though REG_MDP5_PIPE_REQPRIO_FIFO_WM_* registers
are part of the PIPE registers, their functionality is to reflect
the behavior of the SMP block. These registers access is now
restricted to the SMP module.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The core clock rate depends on the hw configuration. Once we have
read the hardware revision, we can set the core clock to its
maximum value.
Before then, the clock is set at a rate supported by all MDP5
revisions.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
For mdp5, the irqs of hdmi/eDP/dsi0/dsi1 blocks get routed through the
mdp block. In order to decouple hdmi/eDP/etc, register an irq domain
in mdp5. When hdmi/dsi/etc are used with mdp4, they can directly setup
their irqs in their DT nodes as normal. When used with mdp5, instead
set the mdp device as the interrupt-parent, as in:
mdp: qcom,mdss_mdp@fd900000 {
compatible = "qcom,mdss_mdp";
interrupt-controller;
#interrupt-cells = <1>;
...
};
hdmi: qcom,hdmi_tx@fd922100 {
compatible = "qcom,hdmi-tx-8074";
interrupt-parent = <&mdp>;
interrupts = <8 0>; /* MDP5_HW_INTR_STATUS.INTR_HDMI */
...
};
There is a slight awkwardness, in that we cannot disable child irqs
at the mdp level, they can only be cleared in the child block. So
you must not use threaded irq handlers in the child. I'm not sure
if there is a better way to deal with that.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Split up hdmi_init() into hdmi_init() (done at hdmi sub-device
bind/probe time) and hdmi_modeset_init() done from master driver's
modeset_init().
Anything that can fail due to dependencies on other drivers which
may be missing or not probed yet should go in hdmi_init(), so that
devm error/cleanup paths work properly.
Signed-off-by: Rob Clark <robdclark@gmail.com>
MDP5 has several functional blocks (ie: VIG/RGB pipes, LMs, ...).
From one revision to another, these blocks' base addresses might
change due to the number of instances present in the MDP5 hw.
A way of dealing with these offset changes is to introduce
dynamic offsets 'per block'.
This change adds support for the new revision of MDP5: v1.3.
The idea is to define one hw config per MDP version and select
either one of them at runtime, after reading the MDP5 version.
Once the MDP version is known, 'per block' dynamic offsets
are initialized through a global pointer, which is then used for
read/write register access.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Downstream kernel IOMMU had a non-standard way of dealing with multiple
devices and multiple ports/contexts. We don't need that on upstream
kernel, so rip out the crazy.
Note that we have to move the pinning of the ringbuffer to after the
IOMMU is attached. No idea how that managed to work properly on the
downstream kernel.
For now, I am leaving the IOMMU port name stuff in place, to simplify
things for folks trying to backport latest drm/msm to device kernels.
Once we no longer have to care about pre-DT kernels, we can drop this
and instead backport upstream IOMMU driver.
Signed-off-by: Rob Clark <robdclark@gmail.com>
This changes activates the iommu support for MDP5, through the
platform config structure.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
If probe fails after IOMMU is attached, we need to detach in order to
clean up properly. Before this change, IOMMU faults would occur if the
probe failed (-EPROBE_DEFER).
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add support for the new MDP5 display controller block. The mapping
between parts of the display controller and KMS is:
plane -> PIPE{RGBn,VIGn} \
crtc -> LM (layer mixer) |-> MDP "device"
encoder -> INTF /
connector -> HDMI/DSI/eDP/etc --> other device(s)
Unlike MDP4, it appears we can get by with a single encoder, rather
than needing a different implementation for DTV, DSI, etc. (Ie. the
register interface is same, just different bases.)
Also unlike MDP4, all the IRQs for other blocks (HDMI, DSI, etc) are
routed through MDP.
And finally, MDP5 has this "Shared Memory Pool" (called "SMP"), from
which blocks need to be allocated to the active pipes based on fetch
stride.
Signed-off-by: Rob Clark <robdclark@gmail.com>
