macb0 DT node can have phy child nodes, so add the #{address,
size}_cells for macb0 node.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add the leds DT node in the dts file.
In the leds, d10 is set as heartbeat led.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add alias, node declaration and pinctrl for i2c1 (aka: twi1).
Signed-off-by: Philip Attfield <phil.attfield@seqlabs.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Gpio-keys nodes are not using the "reg" property in their sub nodes.
So, there is no need to define #address-cells and #size-cells properties
in gpio-keys nodes: we remove them in these new boards.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
File name had at91 prefix, which is not the case anymore for SAMA5D3.
AT91SAM9x5 was mentioned instead of SAMA5D3 SoC.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Enable ISI and ov2640 for at91sam9g25ek board.
Meantime, we need to disable the mmc1 and spi0 as they have pin conflict
with ISI.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add the camera sensor ov2640 dt support. And connect sensor to isi node
as well.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add a new file: at91sam9x5_isi.dtsi, which includes ISI node and
pinctrls.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Following the introduction of the Marvell Armada 39x support, let's
enabled it by default in mvebu_v7_defconfig.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This commit adds the Device Tree files for the Armada 39x family of
processors, as well as one Armada 398 Development Board.
Like for other Marvell EBU families, a common armada-39x.dtsi contains
the description of the common features of all Armada 39x SoCs, while
armada-390.dtsi and armada-398.dtsi respectively describe the
specificities of those SoCs.
Finally, an armada-398-db.dts file is added to describe the Armada 398
Development Board itself.
So far, the following features are supported:
* SMP: dual Cortex-A9
* Basic ARM IPs: SCU, timer, GIC, L2 cache
* Basic Marvell IPs: pin-muxing, clocks, system controller, MBus
controller, MPIC interrupt controller, timer, CPU reset for SMP,
PMSU.
* I2C
* SPI
* SDHCI
* XOR
* NAND
* UART
* PCIe
Additional features will be supported in the future.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This commit adds the core support for Armada 39x, which is quite
simple:
- a new Kconfig option which selects the appropriate clock and
pinctrl drivers as well as other common features (GIC, L2 cache,
SMP, etc.)
- a new DT_MACHINE_START which references the top-level compatible
strings supported for the Marvell Armada 39x.
- a new SMP enable-method. The mechanism to enable CPUs for Armada
39x appears to be the same as Armada 38x. However, we do not want
to use marvell,armada-380-smp in the Device Tree, in the case of
the discovery of a subtle difference in the future, which would
require changing the Device Tree. And the enable-method isn't a
compatible string: you can't specify several values and expect a
fallback on the second string if the first one isn't
supported. Therefore, we simply declare the SMP enable method
"marvell,armada-390-smp" as doing the same thing as the
"marvell,armada-380-smp" one.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Device Tree nodes describing the MPIC nodes on Armada 370, 375,
38x and XP had a unit address that did not match the first reg
property, as suggested by the ePAPR. This commit fixes that.
[gregory.clement@free-electrons.com: removed the armada-38x part, as it
was already applied by a previous patch]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This commit adds the stdout-path property in /chosen for all Armada
boards that were not yet carrying this property, and gets rid of
/chosen/bootargs which becomes unneeded: earlyprintk should not be
used by default, and the console= parameter is replaced by the
/chosen/stdout-path property.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This commit adds 'serialX' aliases for the various serial ports on
Armada 370, 375, 38x and XP platforms. It will allow the usage of the
stdout-path property.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Having aliases for Ethernet devices is useless, since the networking
subsystem unfortunately doesn't care about aliases to name network
interfaces.
Note that the 'aliases' nodes in armada-370-xp.dtsi and armada-xp.dtsi
become empty, but that we keep it as is since a followup patch will
re-add some aliases to it.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This commit adds the standard uart0 and uart1 DT labels to the Device
Tree description of the Marvell Armada 375 SoC.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Armada 38x had a label for UART0, but not UART1. This commit fixes
that.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
On Marvell Armada 38x, the USB2 controller registers are at 0x58000,
so the corresponding Device Tree node should have a unit address of
58000, and not 50000. We were using 50000 due to an incorrect
copy/pastebin of Armada 370/XP code.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
As suggested by Stephen Boyd, this commit adds the __initconst
specifier to the dt_compat table declarations used by the
DT_MACHINE_START structures in mach-mvebu land.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Armada 385 Access Point Development Board has a 1GB NAND SLC chip from
Micron as its main storage. Enable it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add a DSA section to the DT blob representing the Ethernet switch.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
On the LaCie 2Big Network v2 (net2big_v2) board, the fan alarm is not
wired to the I2C fan controller but to a separe GPIO. This GPIO can be
controlled by using the gpio-fan driver.
This patch adds the gpio-fan alarm description in the net2big_v2 DTS.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The unit-address is supposed to be equal the first reg address, which is not
the case for the MPIC, that uses the mbus-controller one. Fix this.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This add common pinctrl settings for pcie[01]_clkreq, spi1, i2c[23],
and internal i2c mux. These settings have either one or two options
only, so put them into the SoC dtsi instead of repeating them on
board level.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Since turning on idle-halt in commit fe46aa679f (ARM: at91/dt: add
sam9 watchdog default options to SoCs), SoCs compatible with at91sam9260-wdt
no longer reboot if the watchdog times out while the CPU is in idle state.
Removing the 'idle-halt' flag that was set by default fixes this.
Signed-off-by: Michel Marti <mma@objectxp.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
[nicolas.ferre@atmel.com: rework the commit message]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
There is now only one defconfig for the at91rm9200 and at91sam9. Add ethernet
support for the at91rm9200.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Recent distributions and userspace tools after 2009/2010 depend on
the existence of /sys/class/block/, and will not work with this option enabled.
Signed-off-by: Anthony Harivel <anthony.harivel@emtrion.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Corrected pins used by usart3.
Signed-off-by: Jonas Andersson <jonas@microbit.se>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Pull networking fixes from David Miller:
1) If an IPVS tunnel is created with a mixed-family destination
address, it cannot be removed. Fix from Alexey Andriyanov.
2) Fix module refcount underflow in netfilter's nft_compat, from Pablo
Neira Ayuso.
3) Generic statistics infrastructure can reference variables sitting on
a released function stack, therefore use dynamic allocation always.
Fix from Ignacy Gawędzki.
4) skb_copy_bits() return value test is inverted in ip_check_defrag().
5) Fix network namespace exit in openvswitch, we have to release all of
the per-net vports. From Pravin B Shelar.
6) Fix signedness bug in CAIF's cfpkt_iterate(), from Dan Carpenter.
7) Fix rhashtable grow/shrink behavior, only expand during inserts and
shrink during deletes. From Daniel Borkmann.
8) Netdevice names with semicolons should never be allowed, because
they serve as a separator. From Matthew Thode.
9) Use {,__}set_current_state() where appropriate, from Fabian
Frederick.
10) Revert byte queue limits support in r8169 driver, it's causing
regressions we can't figure out.
11) tcp_should_expand_sndbuf() erroneously uses tp->packets_out to
measure packets in flight, properly use tcp_packets_in_flight()
instead. From Neal Cardwell.
12) Fix accidental removal of support for bluetooth in CSR based Intel
wireless cards. From Marcel Holtmann.
13) We accidently added a behavioral change between native and compat
tasks, wrt testing the MSG_CMSG_COMPAT bit. Just ignore it if the
user happened to set it in a native binary as that was always the
behavior we had. From Catalin Marinas.
14) Check genlmsg_unicast() return valud in hwsim netlink tx frame
handling, from Bob Copeland.
15) Fix stale ->radar_required setting in mac80211 that can prevent
starting new scans, from Eliad Peller.
16) Fix memory leak in nl80211 monitor, from Johannes Berg.
17) Fix race in TX index handling in xen-netback, from David Vrabel.
18) Don't enable interrupts in amx-xgbe driver until all software et al.
state is ready for the interrupt handler to run. From Thomas
Lendacky.
19) Add missing netlink_ns_capable() checks to rtnl_newlink(), from Eric
W Biederman.
20) The amount of header space needed in macvtap was not calculated
properly, fix it otherwise we splat past the beginning of the
packet. From Eric Dumazet.
21) Fix bcmgenet TCP TX perf regression, from Jaedon Shin.
22) Don't raw initialize or mod timers, use setup_timer() and
mod_timer() instead. From Vaishali Thakkar.
23) Fix software maintained statistics in bcmgenet and systemport
drivers, from Florian Fainelli.
24) DMA descriptor updates in sh_eth need proper memory barriers, from
Ben Hutchings.
25) Don't do UDP Fragmentation Offload on RAW sockets, from Michal
Kubecek.
26) Openvswitch's non-masked set actions aren't constructed properly
into netlink messages, fix from Joe Stringer.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (116 commits)
openvswitch: Fix serialization of non-masked set actions.
gianfar: Reduce logging noise seen due to phy polling if link is down
ibmveth: Add function to enable live MAC address changes
net: bridge: add compile-time assert for cb struct size
udp: only allow UFO for packets from SOCK_DGRAM sockets
sh_eth: Really fix padding of short frames on TX
Revert "sh_eth: Enable Rx descriptor word 0 shift for r8a7790"
sh_eth: Fix RX recovery on R-Car in case of RX ring underrun
sh_eth: Ensure proper ordering of descriptor active bit write/read
net/mlx4_en: Disbale GRO for incoming loopback/selftest packets
net/mlx4_core: Fix wrong mask and error flow for the update-qp command
net: systemport: fix software maintained statistics
net: bcmgenet: fix software maintained statistics
rxrpc: don't multiply with HZ twice
rxrpc: terminate retrans loop when sending of skb fails
net/hsr: Fix NULL pointer dereference and refcnt bugs when deleting a HSR interface.
net: pasemi: Use setup_timer and mod_timer
net: stmmac: Use setup_timer and mod_timer
net: 8390: axnet_cs: Use setup_timer and mod_timer
net: 8390: pcnet_cs: Use setup_timer and mod_timer
...
Commit ff04660e48b20 ("ARM: at91/dt: add SRAM nodes") used the same base
address for sram0 and sram1 leading to the following warning:
WARNING: CPU: 0 PID: 1 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x50/0x70()
sysfs: cannot create duplicate filename '/devices/platform/300000.sram'
Fix the base address for sram1.
Signed-off-by: Alexander Stein <alexanders83@web.de>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
On some platforms, there are multiple SRAM nodes defined in the device tree but
some of them are disabled, leading to allocation failure. Try to find the first
enabled SRAM node and allocate from it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Tested-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
at91rm9200 standby and suspend to ram has been broken since
00482a4078. It is wrongly using AT91_BASE_SYS which is a physical address
and actually doesn't correspond to any register on at91rm9200.
Use the correct at91_ramc_base[0] instead.
Fixes: 00482a4078 (ARM: at91: implement the standby function for pm/cpuidle)
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The DDRSDR controller fails miserably to put LPDDR1 memories in
self-refresh. Force the controller to think it has DDR2 memories
during the self-refresh period, as the DDR2 self-refresh spec is
equivalent to LPDDR1, and is correctly implemented in the
controller.
Assume that the second controller has the same fault, but that is
untested.
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Removed timeout on XTAL, PLL lock and Master Clock Ready, hang if
something went wrong instead of continuing in unknown condition. There
is not much we can do if a PLL lock never ends, we are running in SRAM
and we will not be able to connect back the sdram or ddram in order to
be able to fire up a message or just panic.
As a bonus, not decounting the timeout register in slow clock mode
reduce cumulated suspend time and resume time from ~17ms to ~15ms.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Acked-by: Wenyou.Yang <wenyou.yang@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Use "This enables" in the Kconfig help text to fix grammar.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Also fix all machine files to make use of it and while at it also make
the pad lists __initconst.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
DT file to enable the Wireless Audio reference design based on the
BCM58305.
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Tested-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Jonathan Richardson <jonathar@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
