Since the DFS code appears to process the phy errors
ATH9K_PHYERR_RADAR and ATH9K_PHYERR_FALSE_RADAR_EXT,
check for the correct phyerr status in the main RX
tasklet routine.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If usb auto suspend is enabled or system run in to suspend/resume
cycle, ath9k-htc adapter will stop to response. It is reproducible on xhci HCs.
Host part of problem:
XHCI do timing calculation based on Transfer Type and bInterval,
immediately after device was detected. Ath9k-htc try to overwrite
this parameters on module probe and some changes in FW,
since we do not initiate usb reset from the driver this changes
are not took to account. So, before any kind of suspend or reset,
host controller will operate with old parameters. Only after suspend/resume
and if interface id stay unchanged, new parameters will by applied. Host
will send bulk data with no intervals (?), which will cause
overflow on FIFO of EP4.
Firmware part of problem:
By default, ath9k-htc adapters configured with EP3 and EP4
as interrupt endpoints. Current firmware will try to overwrite
ConfigDescriptor to make EP3 and EP4 bulk. FIFO for this endpoints
stay not reconfigured, so under the hood it is still Int EP.
This patch is revert of 4a0e8ecca4 commit which trying to
reduce CPU usage on some systems. Since it will produce more bug
as fixes, we will need to find other way to fix it.
here is comment from kernel source which has some more explanation:
* Some buggy high speed devices have bulk endpoints using
* maxpacket sizes other than 512. High speed HCDs may not
* be able to handle that particular bug, so let's warn...
in our case EP3 and EP4 have maxpacket sizes = 64!!!
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix for TCP iperf from Windows to Linux stall after about 1sec
Hardware reports false errors in some situations:
Microsoft IP stack, in violation of RFC 1624, set TCP checksum that should be 0x0
as 0xffff. hardware report Rx csum error. If HW csum absolutely trusted,
this frame can be never received, as re-transmitted one will have same csum problem.
In addition, it mess up block ack reorder buffer, as if packet dropped, it is not score boarded
there.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If that flag stays set for a buffer that already ran through the tx path
once, it might cause issues in tx completion processing. Better clear it
early to ensure that this does not happen
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath_tid_drain is only called when a station entry is being removed, so
there is no point in still tracking BAW state. Remove some unnecessary
code and a bogus TODO comment related to this.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
They are not implemented, and accessing them might trigger errors
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Writing to that file is unnecessary and quirky, the antenna API should
be used instead. Use debugfs_create_u8 to allow reading the values.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 uses debugfs_remove_recursive, so there's no need for the
driver to do an explicit cleanup of its sta debugfs entry.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also reduce the size of a few fields where possible
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Similar to a race condition that exists in the tx path, the hardware
might re-read the 'next' pointer of a descriptor of the last completed
frame. This only affects non-EDMA (pre-AR93xx) devices.
To deal with this race, defer clearing and re-linking a completed rx
descriptor until the next one has been processed.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To allow drivers to implement per-interface testmode operations
more easily, pass a wdev pointer if any identification for one
was given from userspace. Clean up the code a bit while at it.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The LNA combining algorithm has to be run for cards
that support the required diversity features, make
sure that that correct conditions are met before
enabing this algorithm.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BTCOEX has to be *disabled* for WLAN RX diversity to
work on combo cards.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Create a per-vif dummy node entry for keeping the multicast software
queues. This helps in setups with a lot of mulitcast traffic that could
otherwise potentially drown out unicast traffic to stations.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of trying to schedule the same TID multiple times in a loop,
iterate over other TIDs/stations first.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a first step for improving fairness between legacy and 802.11n
traffic, and it should also improve reliability of resets and channel
changes by keeping the hardware queue depth very short.
When an aggregation session is torn down, all packets in the retry queue
will be removed from the BAW and freed.
For all subframes that have not been transmitted yet, the A-MPDU flag
will be cleared, and a sequence number allocated. This ensures that the
next A-MPDU session will get the correct initial sequence number.
This happens both on aggregation session start and stop.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Otherwise in some cases, EAPOL frames might be filtered during the
initial handshake, causing delays and assoc failures.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the tid aggregation state has been marked as inactive, free
completed tx packets immediately. When a new aggregation session has not
been initialized yet, the BAW checks do not recognize it as expired.
Might fix potential stalls in setting up a new aggregation session.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- Allow ath_tx_get_tid_subframe to return non-AMPDU subframes.
- Reset the tid paused state on aggregation stop
- Initialize software queues even when HT is not supported
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a packet has been tracked as part of the BlockAck window and added
to the hardware queue, it can end up back in the TID queue again with
fi->retries still set to 0 (e.g. if the frame was filtered). Keep an
extra bit for the BAW tracking status to fix this corner case.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The check for ATH_AMPDU_SUBFRAME_DEFAULT is unnecessary, since it's set
to half the maximum BlockAck Window size, which is already the maximum
value that h_baw could possibly have. Also remove unnecessary variables.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Improves packet retry order and helps with further tx queueing
improvements.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make sure that CONFIG_ATH9K_BTCOEX_SUPPORT is used for
the WLAN/BT RX diversity hooks.
Reported by the kernel build testing backend.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In our Fuz testing, reference client corrupts the dest mac to "00:00:00:00:00:00"
in the WPA2 handshake no 2. During driver init the sta_list entries mac
addresses are by default "00:00:00:00:00:00". Driver returns an invalid
pointer (conn) and the drver shall crash, if rxtids (aggr_conn)
skb queues are accessed, since they would not be initialized.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Make sure to cancel heart beat timer before
freeing wmi to avoid potential NULL pointer
dereference.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Unify the PCI options location.
By default the SoC PS option is disabled to boost the
performance and due to poor stability on early HW revisions.
In future we can remove the module parameter and turn on/off
the PS for given hardware.
This change also makes the pci module parameter for SoC PS static.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
During a HW reset, the diversity config is programmed
in the set_board_values() eeprom callback, there is no
need to do it again by calling ath_ant_comb_update().
Fixed antenna support is not fully handled for 1-stream
cards, it can be done later.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
WB225 based cards like CUS198 and CUS230 support
both fast antenna diversity and LNA combining. Add support
for this and also program the SWCOM register with the
correct "ant_ctrl_comm2g_switch_enable" value.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CUS198/CUS230 cards require a custom value to be
programmed into the SWCOM register. Assign this during
init time.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This variable is redundant since we can use
common->bt_ant_diversity to determine if diversity
has to be enabled/disabled.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The MC_GAIN_CTL/CCK_DETECT registers have to be programmed
with the correct configuration values if WLAN/BT RX diversity
is enabled. Add this and also take care of the BTCOEX mode
when fast diversity is enabled/disabled.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A custom solution for Asus is WB195 based and supports
WLAN/BT Rx diversity. Identify this card and set the
capability.
CUS198/CUS230, which are based on WB225 also support
WLAN/BT Rx diversity.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use "ath9k_hw_set_bt_ant_diversity" instead.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make use of this capability to restrict the usage of the
debugfs file and modparam using which this feature can
be enabled.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For single-chain WLAN+BT cards, the BT antenna can be used for
WLAN RX when the BT interface is disabled. Rename the modparam
"antenna_diversity" to "bt_ant_diversity" to clarify this.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CUS198/CUS230 need a few tweaks in the antenna diversity
algorithm to accomodate RSSI variation. Add a couple
of knobs to control low RSSI threshold and fast antenna
diversity bias values.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes interrupt-related issue when no
interfaces were running thus the device was
considered powered down.
The power_down() function isn't really powering
down the device. It simply assumed it won't
interrupt. This wasn't true in some cases and
could lead to paging failures upon FW indication
interrupt (i.e. FW crash) because some structures
aren't allocated in that device state.
One reason for that was that ar_pci->started
wasn't reset. The other is interrupts should've
been masked when teardown starts.
The patch reorganized interrupt setup and makes
sure ar_pci->started is reset accordingly.
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
pci_disable_msi() must be called if the initial
request_irq() fails.
Also add a warning message so it's possible to
distinguish request_irq() failure and
pci_enable_msi() failure.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The private memory area in vif provided by
mac80211 isn't guaranteed to be zeroed.
This patch should fix issues when switching
between STA and AP interface types.
The tim_bitmap could become polluted by STA bssid
field (since it's a union), wep_keys array
could also become polluted with invalid pointers
and probably much more.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
