Disable the 8259A when routing of the timer interrupt through the chip to
the local APIC of the primary processor has failed.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Remove the "disable_8254_timer" and "enable_8254_timer" kernel
parameters. Now that AEOI acknowledgements are no longer needed for
correct timer operation, the 8259A can be kept disabled unconditionally
unless interrupts, either timer or watchdog ones, are actually passed
through it.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The code that used to be in do_slow_gettimeoffset() that relied on the
IRR bit of the master 8259A PIC for IRQ0 to check the state of the output
timer 0 of the PIT is no longer there. As a result, there is no need to
use the POLL command to acknowledge the timer interrupt in the "8259A
Virtual Wire", except for the NMI watchdog when the i82489DX APIC is used
(this is because this particular APIC treats NMIs as level-triggered and
keeping the input asserted would keep motherboard NMI sources held off for
too long). Remove the unneeded bits and adjust comments accordingly.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Use PAGE_OFFSET macro instead of using 0xffff810000000000UL directly.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: hpa@zytor.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
1) Remove __meminit from update_pages_count. It is used inside
split_pages()
2) Make the code depend on PROC_FS. Doing statistics for nothing is
useless and not adding useless code is nice to the Linux tiny folks.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add information about the mapping state of the direct mapping to
/proc/meminfo. I chose /proc/meminfo because that is where all the other
memory statistics are too and it is a generally useful metric even
outside debugging situations. A lot of split kernel pages means the
kernel will run slower.
This way we can see how many large pages are really used for it and how
many are split.
Useful for general insight into the kernel.
v2: Add hotplug locking to 64bit to plug a very obscure theoretical race.
32bit doesn't need it because it doesn't support hotadd for lowmem.
Fix some typos
v3: Rename dpages_cnt
Add CONFIG ifdef for count update as requested by tglx
Expand description
v4: Fix stupid bugs added in v3
Move update_page_count to pageattr.c
Signed-off-by: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
v2: fix early_panic on this config:
http://redhat.com/~mingo/misc/config-Thu_Jun_19_14_22_37_CEST_2008.bad
reason : struct cpu_vendor_dev size is 16, need to make table to be 16
byte alignment
also print out the cpu supported...
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
"Form follows function". Code is now where it belongs to.
Signed-off-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The name fits better since this is code not only for K8.
Signed-off-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
On Tue, 17 Jun 2008, Rafael J. Wysocki wrote:
>
> BTW, with the C1E patches reverted I don't get the
> WARNING: at /home/rafael/src/linux-next/kernel/smp.c:215 smp_call_function_single+0x3d/0xa2
> in the log. Thomas?
The BROADCAST_FORCE notification uses smp_function_call and therefor
must be run with interrupts enabled.
While at it, add a comment for the BROADCAST_EXIT notifier as well.
Reported-and-bisected-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
C1E on AMD machines is like C3 but without control from the OS. Up to
now we disabled the local apic timer for those machines as it stops
when the CPU goes into C1E. This excludes those machines from high
resolution timers / dynamic ticks, which hurts especially X2 based
laptops.
The current boot time C1E detection has another, more serious flaw
as well: some BIOSes do not enable C1E until the ACPI processor module
is loaded. This causes systems to stop working after that point.
To work nicely with C1E enabled machines we use a separate idle
function, which checks on idle entry whether C1E was enabled in the
Interrupt Pending Message MSR. This allows us to do timer broadcasting
for C1E and covers the late enablement of C1E as well.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
On Feroceon platforms that have a branch prediction unit, bit 11 of the
cp15 control register controls the BPU. This patch keeps the old value
of this bit instead of always clearing it.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
The HP mv2120 has several LEDs that are controlled through gpio.
Export the health LED, the red SATA LEDs as well as two gpios
that control the brightness of _all_ LEDs to userland. The
Ethernet and power LEDs can't be controlled through gpio and the
blue SATA LEDs are handled via the SATA driver.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
This patch adds support for the Marvell Orion-VoIP RD-88F5181L-FXO
Reference Design, and enables use of the ethernet, USB, Cardbus and
mini-PCIe ports.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
This patch adds support for the Marvell Orion-VoIP RD2-88F5181L-GE
Reference Design, and enables use of the ethernet, USB, Cardbus and
mini-PCIe ports.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Don't report a 'selected' IBSS in sta_find_ibss when none was found.
Signed-off-by: Vladimir Koutny <vlado@ksp.sk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On embedded devices we must not route the interrupts through
the PCI core, if our host-bus is not PCI.
Reported-by: Steve Brown <sbrown@cortland.com>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I would like to inform you of our zd1211 based usb wifi adapter (AirTies
WUS-201), which works with the zd1211rw driver with the following device
id definition.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the ieee80211_hw->workqueue is flushed each time
an interface is being removed. However most scheduled work
is not interface specific but device specific, for example things like
periodic work for link tuners.
This patch will move the flush_workqueue() call to directly behind
the call to ops->stop() to make sure the workqueue is only flushed
when all interfaces are gone and there really shouldn't be any scheduled
work in the drivers left.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Putting netif_carrier_on before configuring the driver/device with the
new association state may cause a race (tx frames may be sent before
configuration is done)
Signed-off-by: Guy Cohen <guy.cohen@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Coverity CID: 2265 NEGATIVE_RETURNS
"rate" is of an unsigned type, and the code requires a signed type.
The following patch makes it so.
Signed-off-by: Darren Jenkins <darrenrjenkins@gmailcom>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit a167607255. It duplicates
the change from 8d64c781f0 and only one should be
applied, otherwise some of the Dell quirks are lost.
Thanks to Tony Camuso for catching this.
Acked-by: Tony Camuso <tcamuso@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Patch fixes a race that can result in an oops while adding a
lockres to the dlm lockres tracking list.
Bug introduced by mainline commit 29576f8bb5.
Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
There are various constraints on the use of unit-at-a-time:
- i386 uses no-unit-at-a-time for pre-4.0 (not 4.3)
- x86_64 uses unit-at-a-time always
Uli reported a crash on x86_64 with gcc 4.1.2 with unit-at-a-time,
resulting in commit c0a18111e5
Ingo reported a gcc internal error with gcc 4.3 with no-unit-at-a-timem,
resulting in 22eecde2f9
Benny Halevy is seeing extern inlines not resolved with gcc 4.3 with
no-unit-at-a-time
This patch reintroduces unit-at-a-time for gcc >= 4.0, bringing back the
possibility of Uli's crash. If that happens, we'll debug it.
I started seeing both the internal compiler errors and unresolved
inlines on Fedora 9. This patch fixes both problems, without so far
reintroducing the crash reported by Uli.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Benny Halevy <bhalevy@panasas.com>
Cc: Adrian Bunk <bunk@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Ulrich Drepper <drepper@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Initialise the hardware register settings on boot, to allow the
device to function correctly.
Signed-off-by: Christer Weinigel <christer@weinigel.se>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds the configuration needed for the LCD display on the n30.
Signed-off-by: Christer Weinigel <christer@weinigel.se>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add support for the Acer N35 and related devices.
Signed-off-by: Christer Weinigel <christer@weinigel.se>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add support for the GPIO buttons on the Acer N30.
Signed-off-by: Christer Weinigel <christer@weinigel.se>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add support for the USB D+ pull up on the Acer N30. This is needed
for the USB gadget to work properly.
Signed-off-by: Christer Weinigel <christer@weinigel.se>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Clean up some junk from the official kernel.
The compile-command is something that's only useful for me personally
and doesn't belong in the mainstream kernel.
Signed-off-by: Christer Weinigel <christer@weinigel.se>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Update the S3C2443 clock support to add the prediv clock
that is sourced via a divider from msysclk. Also fix the
setting of p and h clocks from this prediv clock.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
s3c2443_clkcon_enable_p() was reading from the correct register
S3C2443_PCLKCON, but then writing the value back to the wrong
register S3C2443_HCLKCON.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add basic support for AT2440EVB board based on Samsung S3C2440 SoC.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Ramax Lo <ramaxlo@gmail.com>
A recent patch to legacy_serial.c factored out some code by
using the of_match_node() facility to match a node against
an array of possible matches. However, the patch didn't properly
terminate the array causing potential crashes in cases where no
match is found. In addition, the name of the array was poorly
chosen for a static symbol making debugging harder.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
