It was possible for tx queues to be stuck stopped
if AP CSA finalization failed. In that case
neither stop_ap nor do_stop woke the queues up.
This means it was impossible to perform tx at all
until driver was reloaded or a successful CSA was
performed later.
It was possible to solve this in a simpler manner
however this is more robust and future proof
(having multi-vif CSA in mind).
New sdata->csa_block_tx is introduced to keep
track of which interfaces requested tx to be
blocked for CSA. This is required because mac80211
stops all tx queues for that purpose. This means
queues must be awoken only when last tx-blocking
CSA interface is finished.
It is still possible to have tx queues stopped
after CSA failure but as soon as offending
interfaces are stopped from userspace (stop_ap or
ifdown) tx queues are woken up properly.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We don't catch the case if an unsupported protocol is submitted
to the xfrm6 protocol handlers, this can lead to NULL pointer
dereferences. Fix this by adding the appropriate checks.
Fixes: 7e14ea15 ("xfrm6: Add IPsec protocol multiplexer")
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Commit 4068579e1e ("net: Implmement
RFC 6936 (zero RX csums for UDP/IPv6)") introduced zero checksums
being allowed for IPv6, but in the case that a socket disallows a
zero checksum on RX we need to sock_put.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enabling CONFIG_DEBUG_ATOMIC_SLEEP has shown that some rfcomm functions
acquiring spinlocks call sleeping locks further in the chain. Converting
the offending spinlocks into mutexes makes sleeping safe.
Signed-off-by: Libor Pechacek <lpechacek@suse.cz>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Pull networking fixes from David Miller:
1) e1000e computes header length incorrectly wrt vlans, fix from Vlad
Yasevich.
2) ns_capable() check in sock_diag netlink code, from Andrew
Lutomirski.
3) Fix invalid queue pairs handling in virtio_net, from Amos Kong.
4) Checksum offloading busted in sxgbe driver due to incorrect
descriptor layout, fix from Byungho An.
5) Fix build failure with SMC_DEBUG set to 2 or larger, from Zi Shen
Lim.
6) Fix uninitialized A and X registers in BPF interpreter, from Alexei
Starovoitov.
7) Fix arch dependencies of candence driver.
8) Fix netlink capabilities checking tree-wide, from Eric W Biederman.
9) Don't dump IFLA_VF_PORTS if netlink request didn't ask for it in
IFLA_EXT_MASK, from David Gibson.
10) IPV6 FIB dump restart doesn't handle table changes that happen
meanwhile, causing the code to loop forever or emit dups, fix from
Kumar Sandararajan.
11) Memory leak on VF removal in bnx2x, from Yuval Mintz.
12) Bug fixes for new Altera TSE driver from Vince Bridgers.
13) Fix route lookup key in SCTP, from Xugeng Zhang.
14) Use BH blocking spinlocks in SLIP, as per a similar fix to CAN/SLCAN
driver. From Oliver Hartkopp.
15) TCP doesn't bump retransmit counters in some code paths, fix from
Eric Dumazet.
16) Clamp delayed_ack in tcp_cubic to prevent theoretical divides by
zero. Fix from Liu Yu.
17) Fix locking imbalance in error paths of HHF packet scheduler, from
John Fastabend.
18) Properly reference the transport module when vsock_core_init() runs,
from Andy King.
19) Fix buffer overflow in cdc_ncm driver, from Bjørn Mork.
20) IP_ECN_decapsulate() doesn't see a correct SKB network header in
ip_tunnel_rcv(), fix from Ying Cai.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (132 commits)
net: macb: Fix race between HW and driver
net: macb: Remove 'unlikely' optimization
net: macb: Re-enable RX interrupt only when RX is done
net: macb: Clear interrupt flags
net: macb: Pass same size to DMA_UNMAP as used for DMA_MAP
ip_tunnel: Set network header properly for IP_ECN_decapsulate()
e1000e: Restrict MDIO Slow Mode workaround to relevant parts
e1000e: Fix issue with link flap on 82579
e1000e: Expand workaround for 10Mb HD throughput bug
e1000e: Workaround for dropped packets in Gig/100 speeds on 82579
net/mlx4_core: Don't issue PCIe speed/width checks for VFs
net/mlx4_core: Load the Eth driver first
net/mlx4_core: Fix slave id computation for single port VF
net/mlx4_core: Adjust port number in qp_attach wrapper when detaching
net: cdc_ncm: fix buffer overflow
Altera TSE: ALTERA_TSE should depend on HAS_DMA
vsock: Make transport the proto owner
net: sched: lock imbalance in hhf qdisc
net: mvmdio: Check for a valid interrupt instead of an error
net phy: Check for aneg completion before setting state to PHY_RUNNING
...
Pull Ceph fixes from Sage Weil:
"First, there is a critical fix for the new primary-affinity function
that went into -rc1.
The second batch of patches from Zheng fix a range of problems with
directory fragmentation, readdir, and a few odds and ends for cephfs"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
ceph: reserve caps for file layout/lock MDS requests
ceph: avoid releasing caps that are being used
ceph: clear directory's completeness when creating file
libceph: fix non-default values check in apply_primary_affinity()
ceph: use fpos_cmp() to compare dentry positions
ceph: check directory's completeness before emitting directory entry
In the previous commits of this series, we removed all asynchronous
actions which were based on the tasklet handler - "tipc_k_signal()".
So the moment has now come when we can completely remove the tasklet
handler infrastructure. That is done with this commit.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Postpone the actions of resetting all links until after bclink
lock is released, avoiding to asynchronously reset all links.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert allocations of global variables associated with bclink from
static way to dynamical way for the convenience of bclink instance
initialisation. Meanwhile, this also helps TIPC support name space
in the future easily.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we are going to do more jobs when bc_lock is released, the two
operations of holding/releasing the lock should be encapsulated with
functions. In addition, we move bc_lock spin lock into tipc_bclink
structure avoiding to define the global variable.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Postpone the actions of delivering name tables until after node
lock is released, avoiding to do it under asynchronous context.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since previously what all publications pertaining to the lost node
were removed from name table was finished in tasklet context
asynchronously, we need to TIPC_NAMES_GONE flag indicating whether
the node cleanup work is finished or not. But now as the cleanup work
has been finished when node lock is released, the flag becomes
meaningless for us.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Postpone the actions of notifying subscriptions until after node lock
is released, avoiding to asynchronously execute registered handlers
when node is lost.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename setup_blocked variable of node struct to a more common
name called "flags", which will be used to represent kinds of
node states.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move more frequently used variables up to the head of tipc_node
structure, hopefully improving a bit performance.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although we obtain node lock with tipc_node_lock() in most time, there
are still places where we directly use native spin lock interface
to grab node lock. But as we will do more jobs in the future when node
lock is released, we should ensure that tipc_node_lock() is always
called when node lock is taken.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ip_tunnel_rcv(), set skb->network_header to inner IP header
before IP_ECN_decapsulate().
Without the fix, IP_ECN_decapsulate() takes outer IP header as
inner IP header, possibly causing error messages or packet drops.
Note that this skb_reset_network_header() call was in this spot when
the original feature for checking consistency of ECN bits through
tunnels was added in eccc1bb8d4 ("tunnel: drop packet if ECN present
with not-ECT"). It was only removed from this spot in 3d7b46cd20
("ip_tunnel: push generic protocol handling to ip_tunnel module.").
Fixes: 3d7b46cd20 ("ip_tunnel: push generic protocol handling to ip_tunnel module.")
Reported-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Ying Cai <ycai@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is no longer used after commit e837735ec4
(ip6_tunnel: ensure to always have a link local address).
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 6936 relaxes the requirement of RFC 2460 that UDP/IPv6 packets which
are received with a zero UDP checksum value must be dropped. RFC 6936
allows zero checksums to support tunnels over UDP.
When sk_no_check is set we allow on a socket we allow a zero IPv6
UDP checksum. This is for both sending zero checksum and accepting
a zero checksum on receive.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call skb_checksum_init instead of private functions.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call skb_checksum_init instead of private functions.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless-next 2014-05-02
Please pull this batch of updates intended for the 3.16 stream...
For the mac80211 bits, Johannes says:
"In this round we have a large number of small features and
improvements from people too numerous to list here. The only really
bit thing is Michał and Luca's CSA work (including changing how
interface combination verification is done)."
For the Bluetooth bits, Gustavo says:
"Here goes some patches for the -next release. There is nothing
really special for this pull request, just a bunch of refactors,
fixes and clean ups."
For the ath10k/ath6kl bits, Kalle says:
"For ath6kl Kalle fixed a bunch of checkpatch warnings.
In ath10k we had more changes, major ones being:
* fix memory allocation failures after a firmware crash (Michal)
* some rework of DFS configuration to enable it correctly in all cases
(Michal)
* add a new firmware crash option to make it possible to crash 10.1
firmware for testing purposes (Marek P)
* fix RTS/CTS protection in certain cases (Marek K)
* fix wrong RSSI and rate reporting in some cases (Janusz)
* fix firmware stats reporting (Chun, Ben & Bartosz)"
For the iwlwifi bits, Emmanuel says:
"I have here a bunch of unrelated things. I disabled support for
-7.ucode which means that I can removed a lot of code. Eliad has
a brand new feature: we reduce the Tx power when the link allows -
this reduces our power consumption. The regular changes in power and
scan area. One interesting thing though is the patches from Johannes,
we have now GRO which allows to increase our throughput in TCP Rx. The
main advantage is that it reduces the number of TCP Acks - these TCP
Acks are completely useless when we are using A-MPDU since the first
packet of the A-MPDU generates a TCP Ack which is made obsolete by
the next packets."
Along with that, there are a variety of updates to b43, mwifiex,
rtl8180 and wil6210 drivers and a handful of other updates here
and there.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now the core vsock module is the owner of the proto family. This
means there's nothing preventing the transport module from unloading if
there are open sockets, which results in a panic. Fix that by allowing
the transport to be the owner, which will refcount it properly.
Includes version bump to 1.0.1.0-k
Passes checkpatch this time, I swear...
Acked-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Andy King <acking@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes ordering of rtnl notifications during unregister_netdevice
by moving RTM_DELLINK notification to until after ndo_uninit.
The problem was seen with unregistering bond netdevices.
bond ndo_uninit callback generates a few RTM_NEWLINK notifications for
NETDEV_CHANGEADDR and NETDEV_FEAT_CHANGE. This is seen mostly when the
bond is deleted with slaves still enslaved to the bond.
During unregister netdevice (rollback_registered_many to be specific)
bond ndo_uninit is called after RTM_DELLINK notification goes out.
This results in userspace seeing RTM_DELLINK followed by a couple of
RTM_NEWLINK's.
In userspace problem was seen with libnl. libnl cache deletes the bond
when it sees RTM_DELLINK and re-adds the bond with the following
RTM_NEWLINK. Resulting in a stale bond entry in libnl cache when the kernel
has already deleted the bond.
This patch has been tested for bond, bridges and vlan devices.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless 2014-05-01
Please pull the following batch of fixes intended for the 3.15 stream!
For the Bluetooth bits, Gustavo says:
"Some fixes for 3.15. There is a revert for the intel driver, a new
device id, and two important SSP fixes from Johan."
On top of that...
Ben Hutchings gives us a fix for an unbalanced irq enable in an
rtl8192cu error path.
Colin Ian King provides an rtlwifi fix for an uninitialized variable.
Felix Fietkau brings a pair of ath9k fixes, one that corrects a
hardware initialization value and another that removes an (unnecessary)
flag that was being used in a way that led to a software tx queue
hang in ath9k.
Gertjan van Wingerde pushes a MAINTAINERS change to remove himself
from the rt2x00 maintainer team.
Hans de Goede fixes a brcmfmac firmware load hang.
Larry Finger changes rtlwifi to use the correct queue for V0 traffic
on rtl8192se.
Rajkumar Manoharan corrects a race in ath9k driver initialization.
Stanislaw Gruszka fixes an rt2x00 bug in which disabling beaconing
once on USB devices led to permanently disabling beaconing for those
devices.
Tim Harvey provides fixes for a pair of ath9k issues that can lead
to soft lockups in that driver.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently bridge can silently drop ipv4 fragments.
If node have loaded nf_defrag_ipv4 module but have no nf_conntrack_ipv4,
br_nf_pre_routing defragments incoming ipv4 fragments
but nfct check in br_nf_dev_queue_xmit does not allow re-fragment combined
packet back, and therefore it is dropped in br_dev_queue_push_xmit without
incrementing of any failcounters
It seems the only way to hit the ip_fragment code in the bridge xmit
path is to have a fragment list whose reassembled fragments go over
the mtu. This only happens if nf_defrag is enabled. Thanks to
Florian Westphal for providing feedback to clarify this.
Defragmentation ipv4 is required not only in conntracks but at least in
TPROXY target and socket match, therefore #ifdef is changed from
NF_CONNTRACK_IPV4 to NF_DEFRAG_IPV4
Signed-off-by: Vasily Averin <vvs@openvz.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The 'local' variable in __ieee80211_vif_copy_chanctx_to_vlans()
is only used/needed when lockdep is compiled in, mark it as such
to avoid compile warnings in the other case.
While at it, fix some indentation where it's used.
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Defrag user check in ip_expire was not updated after adding support for
"conntrack zones".
This bug manifests as a RFC violation, since the router will send
the icmp time exceeeded message when using conntrack zones.
Signed-off-by: Vasily Averin <vvs@openvz.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
With new additions planned, this code is getting too big for cfg.c.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Expose a new tdls flag for the public ieee80211_sta struct.
This can be used in some rate control decisions.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211_reconfig already holds rtnl, so calling
cfg80211_sched_scan_stopped results in deadlock.
Use the rtnl-version of this function instead.
Fixes: d43c6b6 ("mac80211: reschedule sched scan after HW restart")
Cc: stable@vger.kernel.org (3.14+)
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add locked-version for cfg80211_sched_scan_stopped.
This is used for some users that might want to
call it when rtnl is already locked.
Fixes: d43c6b6 ("mac80211: reschedule sched scan after HW restart")
Cc: stable@vger.kernel.org (3.14+)
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211 is notified about connection failures by
__cfg80211_connect_result() call. However, this
function currently does not free cfg80211 sme.
This results in hanging connection attempts in some cases
e.g. when mac80211 authentication attempt is denied,
we have this function call:
ieee80211_rx_mgmt_auth() -> cfg80211_rx_mlme_mgmt() ->
cfg80211_process_auth() -> cfg80211_sme_rx_auth() ->
__cfg80211_connect_result()
but cfg80211_sme_free() is never get called.
Fixes: ceca7b712 ("cfg80211: separate internal SME implementation")
Cc: stable@vger.kernel.org (3.10+)
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Filter out incoming multicast packages before applying their bitrate
to the rx bitrate station info field to prevent them from setting the
rx bitrate to the basic multicast rate.
Signed-off-by: Henning Rogge <hrogge@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This contains only some minor misc cleanpus. We can spare us the
extra variable declaration in __skb_get_pay_offset(), the cast in
__get_random_u32() is rather unnecessary and in __sk_migrate_realloc()
we can remove the memcpy() and do a direct assignment of the structs.
Latter was suggested by Fengguang Wu found with coccinelle. Also,
remaining pointer casts of long should be unsigned long instead.
Suggested-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code is a bit hard to parse on which registers can be used,
how they are mapped and all play together. It makes much more sense to
define this a bit more clearly so that the code is a bit more intuitive.
This patch cleans this up, and makes naming a bit more consistent among
the code. This also allows for moving some of the defines into the header
file. Clearing of A and X registers in __sk_run_filter() do not get a
particular register name assigned as they have not an 'official' function,
but rather just result from the concrete initial mapping of old BPF
programs. Since for BPF helper functions for BPF_CALL we already use
small letters, so be consistent here as well. No functional changes.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch simplifies label naming for the BPF jump-table.
When we define labels via DL(), we just concatenate/textify
the combination of instruction opcode which consists of the
class, subclass, word size, target register and so on. Each
time we leave BPF_ prefix intact, so that e.g. the preprocessor
generates a label BPF_ALU_BPF_ADD_BPF_X for DL(BPF_ALU, BPF_ADD,
BPF_X) whereas a label name of ALU_ADD_X is much more easy
to grasp. Pure cleanup only.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hhf_change() takes the sch_tree_lock and releases it but misses the
error cases. Fix the missed case here.
To reproduce try a command like this,
# tc qdisc change dev p3p2 root hhf quantum 40960 non_hh_weight 300000
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
else we may fail to forward skb even if original fragments do fit
outgoing link mtu:
1. remote sends 2k packets in two 1000 byte frags, DF set
2. we want to forward but only see '2k > mtu and DF set'
3. we then send icmp error saying that outgoing link is 1500
But original sender never sent a packet that would not fit
the outgoing link.
Setting local_df makes outgoing path test size vs.
IPCB(skb)->frag_max_size, so we will still send the correct
error in case the largest original size did not fit
outgoing link mtu.
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Suggested-by: Maxime Bizon <mbizon@freebox.fr>
Fixes: 5f2d04f1f9 (ipv4: fix path MTU discovery with connection tracking)
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Commit e114a710aa ("tcp: fix cwnd limited checking to improve
congestion control") obsoleted in_flight parameter from
tcp_is_cwnd_limited() and its callers.
This patch does the removal as promised.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuchung discovered tcp_is_cwnd_limited() was returning false in
slow start phase even if the application filled the socket write queue.
All congestion modules take into account tcp_is_cwnd_limited()
before increasing cwnd, so this behavior limits slow start from
probing the bandwidth at full speed.
The problem is that even if write queue is full (aka we are _not_
application limited), cwnd can be under utilized if TSO should auto
defer or TCP Small queues decided to hold packets.
So the in_flight can be kept to smaller value, and we can get to the
point tcp_is_cwnd_limited() returns false.
With TCP Small Queues and FQ/pacing, this issue is more visible.
We fix this by having tcp_cwnd_validate(), which is supposed to track
such things, take into account unsent_segs, the number of segs that we
are not sending at the moment due to TSO or TSQ, but intend to send
real soon. Then when we are cwnd-limited, remember this fact while we
are processing the window of ACKs that comes back.
For example, suppose we have a brand new connection with cwnd=10; we
are in slow start, and we send a flight of 9 packets. By the time we
have received ACKs for all 9 packets we want our cwnd to be 18.
We implement this by setting tp->lsnd_pending to 9, and
considering ourselves to be cwnd-limited while cwnd is less than
twice tp->lsnd_pending (2*9 -> 18).
This makes tcp_is_cwnd_limited() more understandable, by removing
the GSO/TSO kludge, that tried to work around the issue.
Note the in_flight parameter can be removed in a followup cleanup
patch.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This switches a few remaining capable(CAP_NET_ADMIN) to ns_capable so
that root in a user namespace may set tc rules inside that namespace.
Signed-off-by: Stéphane Graber <stgraber@ubuntu.com>
Acked-by: Serge E. Hallyn <serge.hallyn@ubuntu.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit b9f47a3aae (tcp_cubic: limit delayed_ack ratio to prevent
divide error) try to prevent divide error, but there is still a little
chance that delayed_ack can reach zero. In case the param cnt get
negative value, then ratio+cnt would overflow and may happen to be zero.
As a result, min(ratio, ACK_RATIO_LIMIT) will calculate to be zero.
In some old kernels, such as 2.6.32, there is a bug that would
pass negative param, which then ultimately leads to this divide error.
commit 5b35e1e6e9 (tcp: fix tcp_trim_head() to adjust segment count
with skb MSS) fixed the negative param issue. However,
it's safe that we fix the range of delayed_ack as well,
to make sure we do not hit a divide by zero.
CC: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Liu Yu <allanyuliu@tencent.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both TLP and Fast Open call __tcp_retransmit_skb() instead of
tcp_retransmit_skb() to avoid changing tp->retrans_out.
This has the side effect of missing SNMP counters increments as well
as tcp_info tcpi_total_retrans updates.
Fix this by moving the stats increments of into __tcp_retransmit_skb()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Nandita Dukkipati <nanditad@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 1bb8dce57f ("tipc: fix memory
leak during module removal") introduced a memory leak issue: when
name table is stopped, it's forgotten that publication instances are
freed properly. Additionally the useless "continue" statement in
tipc_nametbl_stop() is removed as well.
Reported-by: Jason <huzhijiang@gmail.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This replaces 6 identical code snippets with a call to a new
static inline function.
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
