My patch to validate station flags broke compatibility
with the old station flags setting where all flags are
always set at once since it always set the mask as all
possible flags which ended up being rejected later in
the station add/modify code.
Fix by parsing only the current flags in the old flags
attribute -- new applications and new flags should use
(and will now require) the new flags attribute where
the mask is given by the application.
Reported-and-tested-by: Thomas Hilber <ath9k-dev@toh.cx>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Framebuffer driver needs to fetch the video data during the rising
edge of the VCLK. Otherwise, there are some glitches in the LCD
display.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
0 is a valid IRQ but the interrupt line for the pca935x certainly isn't
connected there which causes it to fail to probe.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Rather than letting them get allocated dynamically where we don't know
where they are, and also name the data line resource as gpio-generic
requires that. Without these changes the GPIOs are useless.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The second MMC slot was only present on revision 1 of Cragganmore so
remove it. Only MMC0 and MMC2 are there on production systems.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Now that we have software runtime power management support this code is
redundant.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The function declarations in plat/s3c64xx-spi.h rely on struct
platform_device but it's not declared by the header causing compiler
warnings if it is included prior to another header which does that.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
dma-ops.h uses samsung_dma_is_dmadev so it needs to have mach/dma.h
included.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Otherwise it'll generate errors if included twice.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Patch 56e46742e8 broke UBIFS debugging messages:
before that commit when UBIFS debugging was enabled, users saw few useful
debugging messages after mount. However, that patch turned 'dbg_msg()' into
'pr_debug()', so to enable the debugging messages users have to enable them
first via /sys/kernel/debug/dynamic_debug/control, which is very impractical.
This commit makes 'dbg_msg()' to use 'printk()' instead of 'pr_debug()', just
as it was before the breakage.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: stable@kernel.org [3.0+]
We switch to dynamic debugging in commit
56e46742e8 but did not take into account that
now we do not control anymore whether a specific message is enabled or not.
So now we lock the "dbg_lock" and release it in every debugging macro, which
make them not so light-weight.
This commit removes the "dbg_lock" protection from the debugging macros to
fix the issue.
The downside is that now our DBGKEY() stuff is broken, but this is not
critical at all and will be fixed later.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: stable@kernel.org [3.0+]
Patch ab50ff6847 broke UBI debugging messages:
before that commit when UBI debugging was enabled, users saw few useful
debugging messages after attaching an MTD device. However, that patch turned
'dbg_msg()' into 'pr_debug()', so to enable the debugging messages users have
to enable them first via /sys/kernel/debug/dynamic_debug/control, which is
very impractical.
This commit makes 'dbg_msg()' to use 'printk()' instead of 'pr_debug()', just
as it was before the breakage.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: stable@kernel.org [3.0+]
Eric and David reported dead machines and traced it to commit
a195f004 ("sched: Fix load-balance lock-breaking"), it turns out
there's still a scenario where we can end up re-trying forever.
Since there is no strict forward progress guarantee in the
load-balance iteration we can get stuck re-retrying the same
task-set over and over.
Creating a forward progress guarantee with the existing
structure is somewhat non-trivial, for now simply terminate the
retry loop after a few tries.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Eric Dumazet <eric.dumazet@gmail.com>
Reported-by: David Ahern <dsahern@gmail.com>
[ logic cleanup as suggested by Eric ]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/1326297936.2442.157.camel@twins
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Introduce an ioctl which permits applications to query whether a block
device is rotational.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Stacking driver queue limits are typically bounded exclusively by the
capabilities of the low level devices, not by the stacking driver
itself.
This patch introduces blk_set_stacking_limits() which has more liberal
metrics than the default queue limits function. This allows us to
inherit topology parameters from bottom devices without manually
tweaking the default limits in each driver prior to calling the stacking
function.
Since there is now a clear distinction between stacking and low-level
devices, blk_set_default_limits() has been modified to carry the more
conservative values that we used to manually set in
blk_queue_make_request().
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Only available for R4000 style TLBs anyway and proper ordering of
initialization code made this crude interface unncecessary.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On MIPS the generic PCI code has always defaulted to L1_CACHE_BYTES
because the architecutre PCI code did not provide a better default.
In particular on systems with S-caches or T-caches this was suboptimal.
Provide a better default by setting pci_dfl_cache_line_size based on
the size of the line size of the lowest level of the cache hierarchy.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2982/
When flushing TLB, if @vma is backed by huge page, we could flush huge
TLB, due to that huge page is defined to be far from normal page.
Signed-off-by: Hillf Danton <dhillf@gmail.com>
Acked-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: "Jayachandran C." <jayachandranc@netlogicmicro.com>
Patchwork: https://patchwork.linux-mips.org/patch/2825/
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Hillf Danton <dhillf@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/3114/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The number of submission & completion queues should be set by calling
Set Features, not Get Features.
Reported-by: Kwok Kong <Kwok.Kong@idt.com>
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Some time ago, Manoel sent us a patch adding more stuff
to the init sequence. However, his patch were also doing
non-related stuff, by changing the init logic without
any good reason. So, it was asked for him to submit a
patch with just the data that has changed, in order to
allow us to better analyze it.
As he didn't what it was requested, I finally found some
time to dig into his init sequence and add it here.
Basically, new stuff is added there. There are a few changes:
1) The removal of the extra (duplicated) logic that puts
the chip into the serial mode;
2) Some Viterbi VBER measurement init data was changed from
0x00 to 0xff for layer A, to match what was done for
layers B and C.
None of those caused any regressions and both make sense
on my eyes.
The other parameters additions actually increased the
tuning quality for some channels. Yet, some channels that
were previously discovered with scan disappered, while
others appeared instead. This were tested in Brasilia,
with an external antena.
At the overall, it is now a little better. So, better to
add these, and then try to figure out a configuration that
would get even better scanning results.
Reported-by: Manoel Pinheiro <pinusdtv@hotmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On mb86a20s, some registers have sub-addresses, while others not.
In order to make easier to compare different settings, group them.
No functional changes in this patch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The DL1 PDM interface adds a little gain depending on the output device.
Add a method to retrieve the gain value for machine driver usage.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Since the nlink count will be 0, we need to use set_nlink rather
than inc_nlink in order to avoid triggering the inc_nlink warning
which was added recently.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
When multiple headphone or other detectable output pins are present,
the power-map has to be updated after resume appropriately, but the
current driver doesn't check all pins but only the first pin (since
it's enough to check it for the mute-behavior). This resulted in the
silent output from the secondary outputs after PM resume.
This patch fixes the problem by checking all pins at (re-)init time.
Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=740347
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If the first mounter fails to recover one of the journals
during mount, the mount should fail.
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Previously, a spectator mount would not even attempt to do
journal recovery for a failed node. This meant that if all
mounted nodes were spectators, everyone would be stuck after
a node failed, all waiting for recovery to be performed.
This is unnecessary since the failed node had a clean journal.
Instead, allow a spectator mount to do a partial "read only"
recovery, which means it will check if the failed journal is
clean, and if so, report a successful recovery. If the failed
journal is not clean, it reports that journal recovery failed.
This makes it work the same as a read only mount on a read only
block device.
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
In function gfs2_inplace_release it was trying to unlock a gfs2_holder
structure associated with a reservation, after said reservation was
freed. The problem is that the statements have the wrong order.
This patch corrects the order so that the reservation is freed after
the gfs2_holder is unlocked.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
This new method of managing recovery is an alternative to
the previous approach of using the userland gfs_controld.
- use dlm slot numbers to assign journal id's
- use dlm recovery callbacks to initiate journal recovery
- use a dlm lock to determine the first node to mount fs
- use a dlm lock to track journals that need recovery
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
All Xonar cards support S/PDIF input, but the cards without optical or
coaxial plugs have only undocumented pin connectors. Support for the
ST/STX was already added in a previous patch; this adds support for the
D1/DX (JP2), DG (J5), DS (J5), and HDAV Slim (J12).
Many thanks to Zoltan Miklos for testing the DS and DX.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Init topology subsystem by cpu registration.
Microblaze Linux kernel is fauling by
"Oops: kernel access of bad area, sig: 11"
because cpu is not initialized.
Signed-off-by: Michal Simek <monstr@monstr.eu>
This card shares PCI ids with Chaintec AV710. Therefore, it will not be
detected automatically, it can only be activated by the module parameter
model=sq210a.
Signed-off-by: Pavel Hofman <pavel.hofman@ivitera.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When two different cards share the same PCI vendor/subvendor
identification, allow card info based on model only.
Do not require subvendor ID.
Signed-off-by: Pavel Hofman <pavel.hofman@ivitera.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add the capture pcm only if there is at least one ADC configured in
the SYSCONF register.
Signed-off-by: Pavel Hofman <pavel.hofman@ivitera.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Before, /proc/asound looked like this:
2 [Default ]: HDSPM - RME RayDAT_f1cd85
RME RayDAT S/N 0xf1cd85 at 0xf7300000, irq 18
In case of a second HDSPM card, its name would be Default_1. This is
cumbersome, because the order of the cards isn't stable across reboots.
To help userspace tools referring to the correct card, this commit
provides a unique id for each card:
2 [HDSPMxf1cd85 ]: HDSPM - RME RayDAT_f1cd85
RME RayDAT S/N 0xf1cd85 at 0xf7300000, irq 18
In this example, userspace (configuration files) would then use
hw:HDSPMxf1cd85 to choose the right card.
The serial is masked to 24bits, so this string is always shorter than
sixteen chars.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some bcm5974 trackpads have a physical button beneath the physical surface.
This patch sets the property bit so user space applications can detect the
trackpad type and act accordingly.
Signed-off-by: Jussi Pakkanen <jussi.pakkanen@canonical.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
If serio_raw_write was always returning number of bytes successfully
sent to serio port and never signalled error condition to the caller.
Change it so that for completely failed transfers appropriate error
code returned to the caller (partially successful writes still return
number of bytes transferred).
Reported-by: Che-liang Chiou <clchiou@chromium.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Commit 8c1c10d570 attempted to signal
POLLHUP | POLLERR condition when polling disconnected device,
unfortunately it did not do it quite correctly.
Reported-by: Che-Liang Chiou <clchiou@chromium.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Recent conversion to module_platform_driver() went a bit too far and
converted not only drivers that used platform_driver_register() but
also ones using platform_driver_probe(), breaking them in process.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://selinuxproject.org/~jmorris/linux-security: (32 commits)
ima: fix invalid memory reference
ima: free duplicate measurement memory
security: update security_file_mmap() docs
selinux: Casting (void *) value returned by kmalloc is useless
apparmor: fix module parameter handling
Security: tomoyo: add .gitignore file
tomoyo: add missing rcu_dereference()
apparmor: add missing rcu_dereference()
evm: prevent racing during tfm allocation
evm: key must be set once during initialization
mpi/mpi-mpow: NULL dereference on allocation failure
digsig: build dependency fix
KEYS: Give key types their own lockdep class for key->sem
TPM: fix transmit_cmd error logic
TPM: NSC and TIS drivers X86 dependency fix
TPM: Export wait_for_stat for other vendor specific drivers
TPM: Use vendor specific function for status probe
tpm_tis: add delay after aborting command
tpm_tis: Check return code from getting timeouts/durations
tpm: Introduce function to poll for result of self test
...
Fix up trivial conflict in lib/Makefile due to addition of CONFIG_MPI
and SIGSIG next to CONFIG_DQL addition.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
autofs4: deal with autofs4_write/autofs4_write races
autofs4: catatonic_mode vs. notify_daemon race
autofs4: autofs4_wait() vs. autofs4_catatonic_mode() race
hfsplus: creation of hidden dir on mount can fail
block_dev: Suppress bdev_cache_init() kmemleak warninig
fix shrink_dcache_parent() livelock
coda: switch coda_cnode_make() to sane API as well, clean coda_lookup()
coda: deal correctly with allocation failure from coda_cnode_makectl()
securityfs: fix object creation races
Just serialize the actual writing of packets into pipe on
a new mutex, independent from everything else in the locking
hierarchy. As soon as something has started feeding a piece
of packet into the pipe to daemon, we *want* everything else
about to try the same to wait until we are done.
Acked-by: Ian Kent <raven@themaw.net>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
