Currently the hdmi driver is using one of the soc i2c busses for ddc probing
and while documentation always specifies i2c5 as hdmi-i2c it could very well
be any other bus as well.
Therefore this is a property of the board and should be specified there.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This enables the recently added display nodes on the firefly and evb,
letting the boards output graphic data over the hdmi port.
This includes enabling of i2c5 on the evb that is used for ddc probing and
setting the lcd-regulators to always on until the hdmi driver learns
about using them.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
As printk() invocation can cause e.g. a TLB miss, printk() cannot be
called before the exception handlers have been properly initialized.
This can happen e.g. when netconsole has been loaded as a kernel module
and the TLB table has been cleared when a CPU was offline.
Call cpu_report() in start_secondary() only after the exception handlers
have been initialized to fix this.
Without the patch the kernel will randomly either lockup or crash
after a CPU is onlined and the console driver is a module.
Signed-off-by: Hemmo Nieminen <hemmo.nieminen@iki.fi>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: stable@vger.kernel.org
Cc: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8953/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When handling a fault in stage-2, we need to resync I$ and D$, just
to be sure we don't leave any old cache line behind.
That's very good, except that we do so using the *user* address.
Under heavy load (swapping like crazy), we may end up in a situation
where the page gets mapped in stage-2 while being unmapped from
userspace by another CPU.
At that point, the DC/IC instructions can generate a fault, which
we handle with kvm->mmu_lock held. The box quickly deadlocks, user
is unhappy.
Instead, perform this invalidation through the kernel mapping,
which is guaranteed to be present. The box is much happier, and so
am I.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Let's assume a guest has created an uncached mapping, and written
to that page. Let's also assume that the host uses a cache-coherent
IO subsystem. Let's finally assume that the host is under memory
pressure and starts to swap things out.
Before this "uncached" page is evicted, we need to make sure
we invalidate potential speculated, clean cache lines that are
sitting there, or the IO subsystem is going to swap out the
cached view, loosing the data that has been written directly
into memory.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Trying to emulate the behaviour of set/way cache ops is fairly
pointless, as there are too many ways we can end-up missing stuff.
Also, there is some system caches out there that simply ignore
set/way operations.
So instead of trying to implement them, let's convert it to VA ops,
and use them as a way to re-enable the trapping of VM ops. That way,
we can detect the point when the MMU/caches are turned off, and do
a full VM flush (which is what the guest was trying to do anyway).
This allows a 32bit zImage to boot on the APM thingy, and will
probably help bootloaders in general.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Use the same transfer speed on both the rk808 and act8846 variants and
remove the status=okay from the rk808 one which is already set in the
shared rk3288-evb.dtsi .
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The evaluation board using the act8846 as main pmic uses two additional
regulators to provide the cpu and gpu voltage. Add these and also add
the link to cpu supply from vdd_cpu.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Daniel Lezcano <daniel.lezcano@linaro.org>
* Select CONFIG_REGULATOR in mach_shmobile defconfig once again
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=joof
-----END PGP SIGNATURE-----
Merge tag 'renesas-defconfig-fixes-for-v3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/defconfig
Merge "Renesas ARM Based SoC Defconfig Fixes for v3.20" from Simon Horman:
* Select CONFIG_REGULATOR in mach_shmobile defconfig once again
* tag 'renesas-defconfig-fixes-for-v3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Select CONFIG_REGULATOR in defconfig once again
Signed-off-by: Olof Johansson <olof@lixom.net>
- add DISP1 power domain for support HDMI support on exynos5420/5422/5800
and the power domain node including FIMD1, MIXER and HDMI modules
(tested on exynos5420 Peach Pit and exynos5800 Peach Pi Chromebooks
and exynos5422 Odroid XU3 by Javier Martinez Canillas)
Note this is including a patch for adding clock IDs for the DISP1 power
domain with Mike and Sylwester's acks so that could be handled together
to avoid non-working.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=9Imn
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
Merge "Samsung 3rd DT updates for v3.20" from Kukjin Kim:
- add DISP1 power domain for support HDMI support on exynos5420/5422/5800
and the power domain node including FIMD1, MIXER and HDMI modules
(tested on exynos5420 Peach Pit and exynos5800 Peach Pi Chromebooks
and exynos5422 Odroid XU3 by Javier Martinez Canillas)
Note this is including a patch for adding clock IDs for the DISP1 power
domain with Mike and Sylwester's acks so that could be handled together
to avoid non-working.
* tag 'samsung-dt-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Add DISP1 power domain for exynos5420
clk: exynos5420: Add IDs for clocks used in DISP1 power domain
Signed-off-by: Olof Johansson <olof@lixom.net>
- for all of Samsung SoCs
: use generic power domain bindings
: add 'dr_mode' property for hsotg/dwc2 devices
- exynos3250-rinato and exynos3250-monk
: add regulator-haptic
- exynos5422-odroidxu3
: reduce total RAM by 22 MiB because last 22 MiB
for secure monitor cannot be accessed by kernel
: add on-board INA231 sensors and LDO26 of PMIC
for the sensors
Note that this is based on tags/samsung-dt
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=DGVz
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
Merge "Samsung 2nd DT updates for v3.20" from Kukjin Kim:
- for all of Samsung SoCs
: use generic power domain bindings
: add 'dr_mode' property for hsotg/dwc2 devices
- exynos3250-rinato and exynos3250-monk
: add regulator-haptic
- exynos5422-odroidxu3
: reduce total RAM by 22 MiB because last 22 MiB
for secure monitor cannot be accessed by kernel
: add on-board INA231 sensors and LDO26 of PMIC
for the sensors
* tag 'samsung-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: reduce total RAM by 22 MiB for exynos5422-odroidxu3
ARM: dts: add on-board INA231 sensors for exynos5422-odroidxu3
ARM: dts: Add regulator-haptic node for exynos3250-monk
ARM: dts: Add regulator-haptic node for exynos3250-rinato
ARM: dts: add 'dr_mode' property to hsotg devices for exynos boards
ARM: dts: convert to generic power domain bindings for exynos DT
Signed-off-by: Olof Johansson <olof@lixom.net>
- add exynos3250 Supsend to RAM support
- recognize MFC v8 devices for exynos5422/5800
- print CPU id/rev during kernel boot
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=MZnm
-----END PGP SIGNATURE-----
Merge tag 'samsung-update' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/soc
Merge "Samsung mach updates for v3.20" from Kukjin Kim:
- add exynos3250 Supsend to RAM support
- recognize MFC v8 devices for exynos5422/5800
- print CPU id/rev during kernel boot
* tag 'samsung-update' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Add exynos3250 suspend-to-ram support
ARM: EXYNOS: Recognize Samsung MFC v8 devices
ARM: SAMSUNG: print CPU id on probe
Signed-off-by: Olof Johansson <olof@lixom.net>
- remove i2c sys configuration from mach-exynos/
: all related codes moved into i2c driver
- remove Samsung specific DMA
: every Samsung stuff uses dmaengine APIs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=2/ZU
-----END PGP SIGNATURE-----
Merge tag 'samsung-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/cleanup
Merge "Samsung cleanup for v3.20" from Kukjin Kim:
- remove i2c sys configuration from mach-exynos/
: all related codes moved into i2c driver
- remove Samsung specific DMA
: every Samsung stuff uses dmaengine APIs
* tag 'samsung-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: SAMSUNG: remove unused DMA infrastructure
ARM: EXYNOS: Remove i2c sys configuration related code
Signed-off-by: Olof Johansson <olof@lixom.net>
The digicolor interrupt controller driver now needs syscon.
Also, as per clocksource maintainer request, we now have a separate config
symbol, CONFIG_DIGICOLOR_TIMER, for the digicolor timer.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Olof Johansson <olof@lixom.net>
Paul Bolle pointed out that commit
d035fdfa27 ("arm64: Add Tegra132
support") included two Kconfig symbols that are now no-ops:
USB_ARCH_HAS_EHCI and HAVE_SMP. So, drop the two symbols.
This second version corrects a thinko in Paul Bolle's E-mail address.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Paul Walmsley <pwalmsley@nvidia.com>
Cc: Allen Martin <amartin@nvidia.com>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit 4bb25789ed ("arm: dma-mapping: plumb our iommu mapping ops
into arch_setup_dma_ops") moved the setting of the DMA operations from
arm_iommu_attach_device() to arch_setup_dma_ops() where the DMA
operations to be used are selected based on whether the device is
connected to an IOMMU. However, the IOMMU detection scheme requires the
IOMMU driver to be ported to the new IOMMU of_xlate API. As no driver
has been ported yet, this effectively breaks all IOMMU ARM users that
depend on the IOMMU being handled transparently by the DMA mapping API.
Fix this by restoring the setting of DMA IOMMU ops in
arm_iommu_attach_device() and splitting the rest of the function into a
new internal __arm_iommu_attach_device() function, called by
arch_setup_dma_ops().
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
The core VM already knows about VM_FAULT_SIGBUS, but cannot return a
"you should SIGSEGV" error, because the SIGSEGV case was generally
handled by the caller - usually the architecture fault handler.
That results in lots of duplication - all the architecture fault
handlers end up doing very similar "look up vma, check permissions, do
retries etc" - but it generally works. However, there are cases where
the VM actually wants to SIGSEGV, and applications _expect_ SIGSEGV.
In particular, when accessing the stack guard page, libsigsegv expects a
SIGSEGV. And it usually got one, because the stack growth is handled by
that duplicated architecture fault handler.
However, when the generic VM layer started propagating the error return
from the stack expansion in commit fee7e49d45 ("mm: propagate error
from stack expansion even for guard page"), that now exposed the
existing VM_FAULT_SIGBUS result to user space. And user space really
expected SIGSEGV, not SIGBUS.
To fix that case, we need to add a VM_FAULT_SIGSEGV, and teach all those
duplicate architecture fault handlers about it. They all already have
the code to handle SIGSEGV, so it's about just tying that new return
value to the existing code, but it's all a bit annoying.
This is the mindless minimal patch to do this. A more extensive patch
would be to try to gather up the mostly shared fault handling logic into
one generic helper routine, and long-term we really should do that
cleanup.
Just from this patch, you can generally see that most architectures just
copied (directly or indirectly) the old x86 way of doing things, but in
the meantime that original x86 model has been improved to hold the VM
semaphore for shorter times etc and to handle VM_FAULT_RETRY and other
"newer" things, so it would be a good idea to bring all those
improvements to the generic case and teach other architectures about
them too.
Reported-and-tested-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Jan Engelhardt <jengelh@inai.de>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com> # "s390 still compiles and boots"
Cc: linux-arch@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
since that's a more logical and accurate place - Leif Lindholm
* Update efibootmgr URL in Kconfig help - Peter Jones
* Improve accuracy of EFI guid function names - Borislav Petkov
* Expose firmware platform size in sysfs for the benefit of EFI boot
loader installers and other utilities - Steve McIntyre
* Cleanup __init annotations for arm64/efi code - Ard Biesheuvel
* Mark the UIE as unsupported for rtc-efi - Ard Biesheuvel
* Fix memory leak in error code path of runtime map code - Dan Carpenter
* Improve robustness of get_memory_map() by removing assumptions on the
size of efi_memory_desc_t (which could change in future spec
versions) and querying the firmware instead of guessing about the
memmap size - Ard Biesheuvel
* Remove superfluous guid unparse calls - Ivan Khoronzhuk
* Delete unnecessary chosen@0 DT node FDT code since was duplicated
from code in drivers/of and is entirely unnecessary - Leif Lindholm
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=iPpM
-----END PGP SIGNATURE-----
Merge tag 'efi-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mfleming/efi into x86/efi
Pull EFI updates from Matt Fleming:
" - Move efivarfs from the misc filesystem section to pseudo filesystem,
since that's a more logical and accurate place - Leif Lindholm
- Update efibootmgr URL in Kconfig help - Peter Jones
- Improve accuracy of EFI guid function names - Borislav Petkov
- Expose firmware platform size in sysfs for the benefit of EFI boot
loader installers and other utilities - Steve McIntyre
- Cleanup __init annotations for arm64/efi code - Ard Biesheuvel
- Mark the UIE as unsupported for rtc-efi - Ard Biesheuvel
- Fix memory leak in error code path of runtime map code - Dan Carpenter
- Improve robustness of get_memory_map() by removing assumptions on the
size of efi_memory_desc_t (which could change in future spec
versions) and querying the firmware instead of guessing about the
memmap size - Ard Biesheuvel
- Remove superfluous guid unparse calls - Ivan Khoronzhuk
- Delete unnecessary chosen@0 DT node FDT code since was duplicated
from code in drivers/of and is entirely unnecessary - Leif Lindholm
There's nothing super scary, mainly cleanups, and a merge from Ricardo who
kindly picked up some patches from the linux-efi mailing list while I
was out on annual leave in December.
Perhaps the biggest risk is the get_memory_map() change from Ard, which
changes the way that both the arm64 and x86 EFI boot stub build the
early memory map. It would be good to have it bake in linux-next for a
while.
"
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit 523d6e9fae (arm64:mm: free the useless initial page table)
introduced a BUG_ON checking for the allocation type but it was
referring the early_alloc() function in the __init section. This patch
changes the check to slab_is_available() and also relaxes the BUG to a
WARN_ON_ONCE.
Reported-by: Will Deacon <will.deacon@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Alternate macro mode is not a property of a macro definition, but a
gas runtime state that alters the way macros are expanded for ever
after (until .noaltmacro is seen).
This means that subsequent assembly code that calls other macros can
break if fpsimdmacros.h is included.
Since these instruction sequences are simple (if dull -- but in a
good way), this patch solves the problem by simply expanding the
.irp loops. The pre-existing fpsimd_{save,restore} macros weren't
rolled with .irp anyway and the sequences affected are short, so
this change restores consistency at little cost.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
When using network driver on keystone and nfs rootfs is used following
error displayed and device halts.
Missing devtmpfs, which is required for udev to run
Halting...
Add the DEVTMPFS option by default to fix this
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Use a brcl 0,2 instruction for jump label nops during compile time,
so we don't mix up the different nops during mcount/hotpatch call
site detection.
The initial jump label code instruction replacement will exchange
these instructions with either a branch or a brcl 0,0 instruction.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add sanity checks to verify that only expected code will be replaced.
If the code patterns do not match print the code patterns and panic,
since something went terribly wrong.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
StrongARM core uses RCSR SMR bit to tell to bootloader that it was reset
by entering the sleep mode. After we have resumed, there is little point
in having that bit enabled. Moreover, if this bit is set before reboot,
the bootloader can become confused. Thus clear the SMR bit on resume
just before clearing the scratchpad (resume address) register.
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Let kernel drivers to control wakeup sources instead of hardcoding them
in the collie.c board file.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use handle_domain_irq instead of handle_IRQ to automatically map
hardware irq number to virq.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As a part of driver consolidation, move GPIO-related IRQ code to
drivers/gpio/gpio-sa1100.c. The code does not use GPIOLIB_IRQCHIP (yet),
because sa1100 does not have a device for gpios, which is a requirement
for GPIOLIB_IRQCHIP. This will be the next step.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As now both SC and GPIO irq domains start from 0 hwirq and do not
contain holes, switch to using irq_domain_add_simple() instead of
irq_domain_add_legacy().
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now there is no difference between low and high GPIO irqdomains. Merge
them into single irqdomain handling all GPIOs.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Low GPIO pins use an interrupt in SC interrupts space. However it's
possible to handle them as if all the GPIO interrupts are instead tied
to single GPIO handler, which later decodes GEDR register and
chain-calls next IRQ handler. So split first 11 interrupts into system
part (IRQ_GPIO0_SC - IRQ_GPIO10_SC) which work exactly like the rest of
system controller interrupts and real GPIO interrupts
(IRQ_GPIO0..IRQ_GPIO10). A single handler sa1100_gpio_handler then
decodes and calls next handler.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The recently added ARM_KERNMEM_PERMS feature works by manipulating
the kernel page tables, which obviously requires an MMU. Trying
to enable this feature when the MMU is disabled results in a lot
of compile errors in mm/init.c, so let's add a Kconfig dependency
to avoid that case.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Minimal builds for v7M are broken when printk is disabled. The caller is
assembly so add the necessary ifdef around the call.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is currently a hardcoded limit of 64KB for the DTB to live in and
be extended with ATAG info. Some DTBs have outgrown that limit:
$ du -b arch/arm/boot/dts/omap3-n900.dtb
70212 arch/arm/boot/dts/omap3-n900.dtb
Furthermore, the actual size passed to atags_to_fdt() included the stack
size which is obviously wrong.
The initial DTB size is known, so use it to size the allocated workspace
with a 50% growth assumption and relocate the temporary stack above that.
This is also clamped to 32KB min / 1MB max for robustness against bad
DTB data.
Reported-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When tearing down the DMA ops for a device via of_dma_deconfigure, we
unconditionally detach the device from its IOMMU domain. For devices
that aren't actually behind an IOMMU, this produces a "Not attached"
warning message on the console.
This patch changes the teardown code so that we don't detach from the
IOMMU domain when there isn't an IOMMU dma mapping to start with.
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Based on
"mfd: syscon: Decouple syscon interface from platform devices"
(sha1: bdb0066df9)
SLCR driver can use syscon/regmap drivers directly.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Convert the integrator PCI driver to use the generic config access
functions.
This changes accesses from __raw_readX/__raw_writeX to readX/writeX
variants. The spinlock is removed because it is unnecessary. The config
read and write functions are already protected with a spinlock and no
access can occur during the .pre_init function.
[arnd: remove unused "flags"]
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
CC: Russell King <linux@arm.linux.org.uk>
CC: linux-arm-kernel@lists.infradead.org
Add the PCI controller node for the Versatile/PB board.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
CC: Russell King <linux@arm.linux.org.uk>
This patch adds new kvm_x86_ops dirty logging hooks to enable/disable dirty
logging for particular memory slot, and to flush potentially logged dirty GPAs
before reporting slot->dirty_bitmap to userspace.
kvm x86 common code calls these hooks when they are available so PML logic can
be hidden to VMX specific. SVM won't be impacted as these hooks remain NULL
there.
Signed-off-by: Kai Huang <kai.huang@linux.intel.com>
Reviewed-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch changes the second parameter of kvm_mmu_slot_remove_write_access from
'slot id' to 'struct kvm_memory_slot *' to align with kvm_x86_ops dirty logging
hooks, which will be introduced in further patch.
Better way is to change second parameter of kvm_arch_commit_memory_region from
'struct kvm_userspace_memory_region *' to 'struct kvm_memory_slot * new', but it
requires changes on other non-x86 ARCH too, so avoid it now.
Signed-off-by: Kai Huang <kai.huang@linux.intel.com>
Reviewed-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch avoids unnecessary dirty GPA logging to PML buffer in EPT violation
path by setting D-bit manually prior to the occurrence of the write from guest.
We only set D-bit manually in set_spte, and leave fast_page_fault path
unchanged, as fast_page_fault is very unlikely to happen in case of PML.
For the hva <-> pa change case, the spte is updated to either read-only (host
pte is read-only) or be dropped (host pte is writeable), and both cases will be
handled by above changes, therefore no change is necessary.
Signed-off-by: Kai Huang <kai.huang@linux.intel.com>
Reviewed-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch adds new mmu layer functions to clear/set D-bit for memory slot, and
to write protect superpages for memory slot.
In case of PML, CPU logs the dirty GPA automatically to PML buffer when CPU
updates D-bit from 0 to 1, therefore we don't have to write protect 4K pages,
instead, we only need to clear D-bit in order to log that GPA.
For superpages, we still write protect it and let page fault code to handle
dirty page logging, as we still need to split superpage to 4K pages in PML.
As PML is always enabled during guest's lifetime, to eliminate unnecessary PML
GPA logging, we set D-bit manually for the slot with dirty logging disabled.
Signed-off-by: Kai Huang <kai.huang@linux.intel.com>
Reviewed-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We don't have to write protect guest memory for dirty logging if architecture
supports hardware dirty logging, such as PML on VMX, so rename it to be more
generic.
Signed-off-by: Kai Huang <kai.huang@linux.intel.com>
Reviewed-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Versatile boards have the same sysregs as other ARM Ltd boards. Add
the nodes in order to enable support for 24MHz counter as sched_clock.
This is a minimal node definition as the existing sub node definition
used on VExpress has some issues raised by Linus W.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
