hpriv->plat_data is 'void *' so there is no need to cast it to
'struct ecx_plat_data *'.
Cc: Mark Langsdorf <mark.langsdorf@calxeda.com>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
cpufreq_notify_transition() and cpufreq_notify_post_transition() shouldn't be
called directly by cpufreq drivers anymore and so these should be marked static.
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CPUFreq core has new infrastructure that would guarantee serialized calls to
target() or target_index() callbacks. These are called
cpufreq_freq_transition_begin() and cpufreq_freq_transition_end().
This patch converts existing drivers to use these new set of routines.
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Whenever we change the frequency of a CPU, we call the PRECHANGE and POSTCHANGE
notifiers. They must be serialized, i.e. PRECHANGE and POSTCHANGE notifiers
should strictly alternate, thereby preventing two different sets of PRECHANGE or
POSTCHANGE notifiers from interleaving arbitrarily.
The following examples illustrate why this is important:
Scenario 1:
-----------
A thread reading the value of cpuinfo_cur_freq, will call
__cpufreq_cpu_get()->cpufreq_out_of_sync()->cpufreq_notify_transition()
The ondemand governor can decide to change the frequency of the CPU at the same
time and hence it can end up sending the notifications via ->target().
If the notifiers are not serialized, the following sequence can occur:
- PRECHANGE Notification for freq A (from cpuinfo_cur_freq)
- PRECHANGE Notification for freq B (from target())
- Freq changed by target() to B
- POSTCHANGE Notification for freq B
- POSTCHANGE Notification for freq A
We can see from the above that the last POSTCHANGE Notification happens for freq
A but the hardware is set to run at freq B.
Where would we break then?: adjust_jiffies() in cpufreq.c & cpufreq_callback()
in arch/arm/kernel/smp.c (which also adjusts the jiffies). All the
loops_per_jiffy calculations will get messed up.
Scenario 2:
-----------
The governor calls __cpufreq_driver_target() to change the frequency. At the
same time, if we change scaling_{min|max}_freq from sysfs, it will end up
calling the governor's CPUFREQ_GOV_LIMITS notification, which will also call
__cpufreq_driver_target(). And hence we end up issuing concurrent calls to
->target().
Typically, platforms have the following logic in their ->target() routines:
(Eg: cpufreq-cpu0, omap, exynos, etc)
A. If new freq is more than old: Increase voltage
B. Change freq
C. If new freq is less than old: decrease voltage
Now, if the two concurrent calls to ->target() are X and Y, where X is trying to
increase the freq and Y is trying to decrease it, we get the following race
condition:
X.A: voltage gets increased for larger freq
Y.A: nothing happens
Y.B: freq gets decreased
Y.C: voltage gets decreased
X.B: freq gets increased
X.C: nothing happens
Thus we can end up setting a freq which is not supported by the voltage we have
set. That will probably make the clock to the CPU unstable and the system might
not work properly anymore.
This patch introduces a set of synchronization primitives to serialize frequency
transitions, which are to be used as shown below:
cpufreq_freq_transition_begin();
//Perform the frequency change
cpufreq_freq_transition_end();
The _begin() call sends the PRECHANGE notification whereas the _end() call sends
the POSTCHANGE notification. Also, all the necessary synchronization is handled
within these calls. In particular, even drivers which set the ASYNC_NOTIFICATION
flag can also use these APIs for performing frequency transitions (ie., you can
call _begin() from one task, and call the corresponding _end() from a different
task).
The actual synchronization underneath is not that complicated:
The key challenge is to allow drivers to begin the transition from one thread
and end it in a completely different thread (this is to enable drivers that do
asynchronous POSTCHANGE notification from bottom-halves, to also use the same
interface).
To achieve this, a 'transition_ongoing' flag, a 'transition_lock' spinlock and a
wait-queue are added per-policy. The flag and the wait-queue are used in
conjunction to create an "uninterrupted flow" from _begin() to _end(). The
spinlock is used to ensure that only one such "flow" is in flight at any given
time. Put together, this provides us all the necessary synchronization.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Make sata_highbank host driver depend on ARCH_HIGHBANK config option
as Calxeda Highbank SATA support is specific to Calxeda Highbank
SoCs and the driver to work requires suitable device tree node to
be defined. Additionally allow the driver build if COMPILE_TEST
config option is set.
Cc: Mark Langsdorf <mark.langsdorf@calxeda.com>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Ensure that no timer callback is running since we are about to free
the timer structure. We cannot guarantee that the call back is called
on the CPU where the timer is running.
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
During suspend, we first stop governors and then suspend cpufreq drivers and
resume must be exactly opposite of that. i.e. resume drivers first and then
start governors.
But the current code in resume enables governors first and then resume drivers.
Fix it be changing code sequence there.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The example uses foo_process_next_request() everywhere else.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Update the documentation for the removal of GENERIC_SUBSYS_PM_OPS in commit
90363ddf0a ("PM: Drop generic_subsys_pm_ops")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
As of commit 05aa55dddb ("PM / Runtime:
Lenient generic runtime pm callbacks"), the generic power management
callbacks pm_generic_runtime_suspend() and pm_generic_runtime_resume()
return 0, not -EINVAL, if the device doesn't provide its own callbacks.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
dev_pm_info.runtime_error has always been a signed int, to store a signed
error code. Correct the documentation.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Revert commit df86f5df79 (ACPI / processor: Make it possible to get
APIC ID via GIC).
APIC ID refers the hardware ID of the CPU, which means MPIDR on
ARM/ARM64, but in ACPI 5.0, GIC ID feild in GIC structure have
no explicit definition and may not refer to the MPIDR.
Commit df86f5df79 assumed that gic->gic_id as MPIDR which may not be
the case, so revert it until the explicit definition of GIC structure
is ready.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
[rjw: Changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The previous commit "ACPICA: Add auto-serialization support for ill-behaved
control methods" introduced the auto-serialization facility as a workaround
that can be enabled by "acpi_auto_serialize":
This feature marks control methods that create named objects as "serialized"
to avoid unwanted AE_ALREADY_EXISTS control method evaluation failures.
Enable method auto-serialization as the default kernel behavior. The new kernel
parameter is also changed from "acpi_auto_serialize" to "acpi_no_auto_serialize"
to reflect the default behavior.
References: https://bugzilla.kernel.org/show_bug.cgi?id=52191
References: http://www.spinics.net/lists/linux-acpi/msg49496.html
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cannot use a sync_level for methods that have been serialized at load-time
or runtime because this may interfere with any existing use of sync_levels
within the ASL code. So, we simply ignore the sync_level for these methods,
thus preserving any existing sync_level priorities. Note, the use of
sync_levels is actually rather rare within BIOS ASL code.
References: http://www.spinics.net/lists/linux-acpi/msg49496.html
Reported-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Reported-by: Sabrina Dubroka <sd@queasysnail.net>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This change adds some additional opcodes that are detected and will
cause a method to be auto-serialized. These opcodes are the various
CreateXField and the FieldUnit opcodes. Lv Zheng.
References: https://bugzilla.kernel.org/show_bug.cgi?id=52191
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This change adds support to automatically mark a control method as
"serialized" if the method creates any named objects. This will
positively prevent the method from being entered by more than one
thread and thus preventing a possible abort when an attempt is
made to create an object twice.
Implemented by parsing all non-serialize control methods at table
load time.
This feature is disabled by default and this patch also adds a new
Linux kernel parameter "acpi_auto_serialize" to allow this feature
to be turned on for a specific boot.
References: https://bugzilla.kernel.org/show_bug.cgi?id=52191
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
According to the reports, the "acpi_serialize" mechanism is broken as:
A. The parallel method calls can still happen when the interpreter lock is
released under the following conditions:
1. External callbacks are invoked, for example, by the region handlers,
the exception handlers, etc.;
2. Module level execution is performed when Load/LoadTable opcodes are
executed, and
3. The _REG control methods are invoked to complete the region
registrations.
B. For the following situations, the interpreter lock need to be released
even for a serialized method while currently, the lock-releasing
operation is marked as a no-op by
acpi_ex_relinquish/reacquire_interpreter() when this mechanism is
enabled:
1. Wait opcode is executed,
2. Acquire opcode is executed, and
3. Sleep opcode is executed.
This patch removes this mechanism and the internal
acpi_ex_relinquish/reacquire_interpreter() APIs. Lv Zheng.
References: https://bugzilla.kernel.org/show_bug.cgi?id=52191
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Make sata_rcar host driver depend on ARCH_SHMOBILE config option as
Renesas R-Car SATA support is specific to Renesas SoCs and the driver
to work requires suitable device tree node (or platform device) to be
defined. Additionally allow the driver build if COMPILE_TEST config
option is set.
Cc: Simon Horman <horms@verge.net.au>
Cc: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch adds a parameter 'auto_update' to the con3270
driver, causing the 'auto_update' feature to be disabled
if unset.
The 'auto_update' feature will cause the con3270 driver
to switch to the console view whenever new system messages
are displayed, which makes working on the 3270 terminal
awkward.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When we plug a 3-ring headset on the Dell machines (VID: 0x10ec0255,
SID: 0x10280632; VID: 0x10ec0293, SID: 0x1028062c; VID: 0x10ec0293,
SID: 0x1028062e), the headset mic can't be detected, after apply this
patch, the headset mic can work well.
BugLink: https://bugs.launchpad.net/bugs/1297581
Cc: David Henningsson <david.henningsson@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This reverts commit d1ba277e79.
As reported by Stephen, this patch breaks linux-next as a ppc patch
suddenly (after 2 years) started using this old api call. So revert it
for now, it will go away in 3.15-rc2 when we can change the PPC call to
the new api.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Tejun Heo <tj@kernel.org>
Cc: Stewart Smith <stewart@linux.vnet.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While working on my tutorial for 2014 Linux Collaboration Summit
I found that the traceon trigger did not work when conditions were
used. The other triggers worked fine though. Looking into it, it
is because of the way the triggers use the ring buffer to store
the fields it will use for the condition. But if tracing is off, nothing
is stored in the buffer, and the tracepoint exits before calling the
trigger to test the condition. This is fine for all the triggers that
only work when tracing is on, but for traceon trigger that is to
work when tracing is off, nothing happens.
The fix is simple, just use a temp ring buffer to record the event
if tracing is off and the event has a trace event conditional trigger
enabled. The rest of the tracepoint code will work just fine, but
the tracepoint wont be recorded in the other buffers.
Cc: Tom Zanussi <tom.zanussi@linux.intel.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The previous commit removed the register_filesystem() call and the
associated error handling, but left the label for the error path that no
longer exists. Remove that too.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
anon_inodefs filesystem is a kernel internal filesystem userspace
shouldn't mess with. Remove registration of it so userspace cannot
even try to mount it (which would fail anyway because the filesystem is
MS_NOUSER).
This fixes an oops triggered by trinity when it tried mounting
anon_inodefs which overwrote anon_inode_inode pointer while other CPU
has been in anon_inode_getfile() between ihold() and d_instantiate().
Thus effectively creating dentry pointing to an inode without holding a
reference to it.
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull nfsd fix frm Bruce Fields:
"J R Okajima sent this early and I was just slow to pass it along,
apologies. Fortunately it's a simple fix"
* 'nfsd-next' of git://linux-nfs.org/~bfields/linux:
nfsd: fix lost nfserrno() call in nfsd_setattr()
Pull vfs fixes from Al Viro:
"These four commits are obvious fixes (a couple of fdget_pos()-related
ones from Eric Biggers, prepend_name() fix, missing checks for false
negatives from __lookup_mnt() in fs/namei.c)"
For now I'm pulling just the four obvious fixes, there's another four
pending in Al's 'for-linus' branch wrt the mnt_hash list that were more
involved.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
rcuwalk: recheck mount_lock after mountpoint crossing attempts
make prepend_name() work correctly when called with negative *buflen
vfs: Don't let __fdget_pos() get FMODE_PATH files
vfs: atomic f_pos access in llseek()
Since Linus hasn't done the release yet and Morimoto-san here are some
additional bug fixes for rcar which Morimoto-san sent overnight.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=doEs
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.15-rcar' into asoc-next
ASoC: A few more fixes for rcar
Since Linus hasn't done the release yet and Morimoto-san here are some
additional bug fixes for rcar which Morimoto-san sent overnight.
# gpg: Signature made Mon 24 Mar 2014 11:21:18 GMT using RSA key ID 7EA229BD
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg: aka "Mark Brown <broonie@debian.org>"
# gpg: aka "Mark Brown <broonie@kernel.org>"
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg: aka "Mark Brown <broonie@linaro.org>"
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>"
A few more updates for the merge window:
- Fixes for the simple-card DAI format DT mess.
- A new driver for Cirrus cs42xx8 devices.
- DT support for a couple more devices.
- A revert of a previous buggy fix for soc-pcm, plus a few more fixes
and cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wKyT
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.15-3' into asoc-next
ASoC: Updates for v3.15
A few more updates for the merge window:
- Fixes for the simple-card DAI format DT mess.
- A new driver for Cirrus cs42xx8 devices.
- DT support for a couple more devices.
- A revert of a previous buggy fix for soc-pcm, plus a few more fixes
and cleanups.
# gpg: Signature made Sun 23 Mar 2014 16:56:11 GMT using RSA key ID 7EA229BD
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg: aka "Mark Brown <broonie@debian.org>"
# gpg: aka "Mark Brown <broonie@kernel.org>"
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg: aka "Mark Brown <broonie@linaro.org>"
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>"
This is mostly a few additional fixes from Lars-Peter, a new driver and
cleaning up a git failure with merging the Intel branch (combined with
an xargs failure to pay attention to error codes). The history lists a
bunch of additional commits for the branch but the content of those
commits is actually present already but not recorded in history due to
git failing. Unfortunately xargs is used in the merge script and it
doesn't do a good job of noticing errors from the commands it invokes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=nG53
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.15-2' into asoc-next
ASoC: Updates for v3.15
This is mostly a few additional fixes from Lars-Peter, a new driver and
cleaning up a git failure with merging the Intel branch (combined with
an xargs failure to pay attention to error codes). The history lists a
bunch of additional commits for the branch but the content of those
commits is actually present already but not recorded in history due to
git failing. Unfortunately xargs is used in the merge script and it
doesn't do a good job of noticing errors from the commands it invokes.
# gpg: Signature made Thu 13 Mar 2014 14:25:44 GMT using RSA key ID 7EA229BD
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg: aka "Mark Brown <broonie@debian.org>"
# gpg: aka "Mark Brown <broonie@kernel.org>"
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg: aka "Mark Brown <broonie@linaro.org>"
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>"
Quite a busy release for ASoC this time, more on janitorial work than
exciting new features but welcome nontheless:
- Lots of cleanups from Takashi for enumerations; the original API for
these was error prone so he's refactored lots of code to use more
modern APIs which avoid issues.
- Elimination of the ASoC level wrappers for I2C and SPI moving us
closer to converting to regmap completely and avoiding some
randconfig hassle.
- Provide both manually and transparently locked DAPM APIs rather than
a mix of the two fixing some concurrency issues.
- Start converting CODEC drivers to use separate bus interface drivers
rather than having them all in one file helping avoid dependency
issues.
- DPCM support for Intel Haswell and Bay Trail platforms.
- Lots of work on improvements for simple-card, DaVinci and the Renesas
rcar drivers.
- New drivers for Analog Devices ADAU1977, TI PCM512x and parts of the
CSR SiRF SoC.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=C5oo
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.15' into asoc-next
ASoC: Updates for v3.15
Quite a busy release for ASoC this time, more on janitorial work than
exciting new features but welcome nontheless:
- Lots of cleanups from Takashi for enumerations; the original API for
these was error prone so he's refactored lots of code to use more
modern APIs which avoid issues.
- Elimination of the ASoC level wrappers for I2C and SPI moving us
closer to converting to regmap completely and avoiding some
randconfig hassle.
- Provide both manually and transparently locked DAPM APIs rather than
a mix of the two fixing some concurrency issues.
- Start converting CODEC drivers to use separate bus interface drivers
rather than having them all in one file helping avoid dependency
issues.
- DPCM support for Intel Haswell and Bay Trail platforms.
- Lots of work on improvements for simple-card, DaVinci and the Renesas
rcar drivers.
- New drivers for Analog Devices ADAU1977, TI PCM512x and parts of the
CSR SiRF SoC.
# gpg: Signature made Wed 12 Mar 2014 23:05:45 GMT using RSA key ID 7EA229BD
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg: aka "Mark Brown <broonie@debian.org>"
# gpg: aka "Mark Brown <broonie@kernel.org>"
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg: aka "Mark Brown <broonie@linaro.org>"
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>"
The .discard/.discard.* sections are used to generate intermediate
results for the assembler (effectively "test assembly".) The output
is waste and should not be retained.
Cc: Stefani Seibold <stefani@seibold.net>
Cc: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Link: http://lkml.kernel.org/n/tip-psizrnant8x3nrhbgvq2vekr@git.kernel.org
There is no real reason why we require transfers to have a completion and
the only user of the completion now checks to see if one has been provided
before using it so stop enforcing this. This makes it more convenient for
drivers to chain multiple asynchronous transfers together.
Signed-off-by: Mark Brown <broonie@linaro.org>
Update SATA AHCI support to make use of the new ahci_da850 host
driver (instead of the generic ahci_platform one) and remove
deprecated ahci_platform_data code.
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add the new ahci_da850 host driver.
Platform changes needed to make DaVinci DA850 SATA AHCI support
fully functional are in the separate "ARM: davinci: da850: update
SATA AHCI support" commit.
Please note that this driver doesn't have the superfluous clock
control code as clock is already handled by the generic AHCI
platform library code.
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Move AHCI platform library code from ahci_platform.c to
libahci_platform.c and fix dependencies for ahci_st,
ahci_imx and ahci_sunxi drivers.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Looking at ST SPEAr1340 AHCI code (the only user of the deprecated
pdata->suspend and pdata->resume) it is obvious the we should return
after calling pdata->suspend() only if the function have returned
non-zero return value. The code has been broken since commit 1e70c2
("ata/ahci_platform: Add clock framework support"). Fix it.
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
If during a SPI transfer with len larger than PCH_MAX_FIFO_DEPTH and the
IRQ handler happens to be called when the transmit FIFO is already empty,
and SPSR_FI_BIT is set consequently, the message
"spi_master spi32766: pch_spi_handler_sub : Transfer is not completed"
is spammed to the systemlog, because tx_index has already increased
further due to the next bytes to be written. This case is uncritical as
new bytes have already been written.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
