this patch adds tick timer, smp entries and generic DT machine
for SiRFmarco dual-core SMP chips.
with the added marco, we change the defconfig, using the same
defconfig, we get a zImage which can work on both prima2 and
marco.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Cc: Mark Rutland <mark.rutland@arm.com>
SiRFmarco is a dual-core cortex-a9 SMP SoC from CSR. this patch
adds the .dtsi and a basic evb board .dts for it.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
This patch adds a soc dtsi for the Wondermedia WM8850.
A board dts file is also included for the W70v2 tablet, with support
for all the drivers currently in mainline.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add support for specifying clock information for the uart clk via the
device tree. This eliminates the need to hardcode rates in the device
tree.
Signed-off-by: Josh Cartwright <josh.cartwright@ni.com>
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add NAND driver DT node and related pinctrl DT data to export NAND
functionality on da850 evm.
Signed-off-by: Kumar, Anil <anilkumar.v@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
For DT, DaVinci platform can use pinctrl-single driver for handling
padconf registers.
Enable PINCTRL Kconfig for MACH_DA8XX_DT platform. Add required
pinctrl DT entries in da850 dts file.
Test procedure
1)Populate DT file with NAND node information.
2)Populate board DT file with pinmux information for NAND.
3)Boot and confirm NAND is detected by the kernel.
4)cat /proc/mtd to show partitions.
Signed-off-by: Kumar, Anil <anilkumar.v@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The AB8500 Pinctrl driver uses PRCMU register addresses to
control Pinctrl related functions. For this to happen, the
Pinctrl driver needs the PRCMU base to work from. We can do
that using standard Open Firmware (of_*) function calls, but
first we need a mechanism to gain access to the PRCMU
device node. We're going to use a Phandle in this case.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
[Added reg-names="prcmu"; to the prcmu DT node]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
this patche deletes hard code that registers clkdev by things like:
clk_register_clkdev(clk, NULL, "b0030000.nand");
clk_register_clkdev(clk, NULL, "b0040000.audio");
clk_register_clkdev(clk, NULL, "b0080000.usp");
prima2 clock controller becomes a clock provider and every dt node
just declares its clock sources by dt prop.
it also makes us easier to extend this driver to support both prima2
and marco as marco has different address mapping with prima2.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
UART modules on Wondermedia SoCs are connected via a gated clock
source, rather than directly to the 24Mhz reference clock. While
uboot enables UART0 for debugging, other UART ports are unavailable
until the clock is enabled.
This patch checks that a valid clock is actually passed from devicetree,
enables the clock in probe. This change removes the fallback when a
clock was not specified as it doesn't apply any longer (and would only
work if the UART clock was already enabled).
DTSI files are updated for VT8500, WM8505 and WM8650.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
From Kukjin Kim:
That branch fixes build error for S3C24XX/S3C64xx. And corrects dw-mshc
properties on EXYNOS5 DT and fixes IRQ mapping on Cragganmore board.
* 'v3.8-samsung-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: S3C64XX: Fix up IRQ mapping for balblair on Cragganmore
ARM: dts: correct the dw-mshc timing properties as per binding
ARM: S3C64XX: Fix build error with CONFIG_S3C_DEV_FB disabled
+ Linux 3.8-rc3
Signed-off-by: Olof Johansson <olof@lixom.net>
As per the current exynos-dw-mshc bindings, dw-mshc-sdr-timing and
dw-mshc-ddr-timing properties are having only two cells, these properties
are wrongly set for exynos5250 based cros5250 and smdk5250 platfroms. This
patch corrects above timing propreties for above platfroms
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Doug Anderson <dianders@chromium.org>
Acked-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iEYEABECAAYFAlD27roACgkQGxsu9jQV9nbc1ACeI8OXnmOgTE9dvO54e6PsEGV4
YtwAn0reO6wsjlK12fkGpM18HVFpEQzh
=vqps
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-3.8-rc4' of git://github.com/mripard/linux into fixes
From Maxime Ripard:
Sunxi dt fixes for 3.8-rc's
* tag 'sunxi-fixes-for-3.8-rc4' of git://github.com/mripard/linux:
ARM: sunxi: Use the Synosys APB UART instead of ns8250
Yet a few more fixes popped up in this week.
The biggest change here is the addition of pinctrl support for Atmel,
which turned out to be almost mandatory to make things working.
The rest are a few fixes for M-Audio usb-audio device and a fix for
regression of HD-audio HDMI codecs with alsactl in the recent kernel.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQIcBAABAgAGBQJQ9nYgAAoJEGwxgFQ9KSmkM84QAKWlUp8NFsr5HNNiwj6urp18
jhPoM4AbMozeb5abfZpWwwalAVhbq/E5R2w2z8ETdnMnd1ohKqhU5Mx/e0mmUprF
3bZoxm8etTFfqallxPBBTj9exF8iAdA/XPNe5Zw2r1jY7w3viZiQYCgivB1TTSOG
wt0Y5SF0FmawyHgqujqEjo4nm/K04Rp4FPS4/MpdjRXCfzmW+x9nP6CBbdDxGk5J
q8v48mOhk7RTBrRCmfCF0Jw/eJNrS9JYL2RagEaKuPFoy5OEm06OwQZZ76mt3XTF
8S7ExCwfmvbzHW8mIKE3ZFLLDXjWgjxh3jQXeULOAYnPrfe4SHTkUF7mCdmHdbG2
sDTh86C3R784aIwhusXPAZGyVZJ7km+wqFPZa+20Jzbo848PBNgDotlRgmULSqlo
cK8Bsuf5QyRmdpVVON58Owo3Mqorp0EtPiFbfwljkr98JsUQrRX5COaAZ+UHmd2i
18fK0rltPhmJkKwKEAx+0vtqcucoAfvxiS1DSNsjafxDXTy1XJYQ/HmmSUeq1uD/
i1b2kN1yzQQ/Kki7dW9YhekoF5WYyzRP0OoPO73ekSioaCimTwDOo7IF3RwbVfQM
G6eiwLkNpA6BWi3V/q3Cic+eKN/NguM9UlZEKYlCpZq01pMLndreG8MNbpub/O3F
97TzflJSAyIGCShKZH6K
=Sd6n
-----END PGP SIGNATURE-----
Merge tag 'sound-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull second round of sound fixes from Takashi Iwai:
"Yet a few more fixes popped up in this week.
The biggest change here is the addition of pinctrl support for Atmel,
which turned out to be almost mandatory to make things working.
The rest are a few fixes for M-Audio usb-audio device and a fix for
regression of HD-audio HDMI codecs with alsactl in the recent kernel."
* tag 'sound-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/hdmi - Work around "alsactl restore" errors
ALSA: usb-audio: selector map for M-Audio FT C400
ALSA: usb-audio: M-Audio FT C400 skip packet quirk
ALSA: usb-audio: correct M-Audio C400 clock source quirk
ALSA: usb - fix race in creation of M-Audio Fast track pro driver
ASoC: atmel-ssc: add pinctrl selection to driver
ARM: at91/dts: add pinctrl support for SSC peripheral
The UART controller used in the A10/A13 is the Synopsys DesignWare 8250.
The wrong use of a regular 8250 driver may lead to a oops during kernel
boot with "irq 17: nobody cared", because the apb UART as an extra
interrupt that gets raised when writing to the LCR when busy.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Both clock nodes in the current device tree are named "clock" and hence
end up being the same node. Rename the nodes to different names to avoid
this. In fact, fixed-clock uses the node name as the clock name, so name
the nodes after the clock they represent. Move the clocks into a
"clocks" sub-node to group them and avoid any possible naming conflicts
with other nodes also named after the device type.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
The BCM2835 has 3 identical I2C controllers. Instantiate them all in the
SoC .dtsi file, and enable the relevant two in the Raspberry Pi board
.dts file.
Note that on the Raspberry Pi Model B revision 1, I2C0 is connected to
the general-purpose expansion header, and I2C1 is connected to the camera
connector. Revision 2 of the board swaps these assignments:-(
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Add the SDHCI device node to the SoC DT file. Add a dummy fixed-clock
to satisfy the SDHCI driver's clock lookup; eventually this should be
replaced by a real clock implementation. Add board specific properties
to the Raspberry Pi board file.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
The Raspberry Pi has either 256MB or 512MB of RAM. However, a portion is
reserved for use by the VideoCore co-processor. The RPi DT contained a
/memreserve/ statement to reserve that RAM. However, the exact amount of
RAM used by the VideoCore is dynamic at boot-time; a firmware config
file specifies the amount. As such, we can't hard-code the size in the
DT. Remove the /memreserve/ statement. The bootloader is expected to
adjust the /memory properties to reflect the RAM size the ARM CPU can
use. Upstream U-Boot certainly does this, although I'm not sure that the
basic firmware does if it boots the kernel directly; users may need to
manually adjust their DT if not using U-Boot.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
* Do not disable SUSPEND
Suspend seems to work fine on the kzm9d.
This is part of an effort reduce differences between mach-shmobile
defconfigs with a view to using a common defconfig.
* Enable PM_RUNTIME
This also seems to work fine on the kzm9d.
This is part of an effort reduce differences between mach-shmobile
defconfigs with a view to using a common defconfig.
* Move kernel command line from defconfig to dts.
This brings us one small step closer to sharing defconfig
between kzm9d and other boards.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
* Enable ARM_APPENDED_DTB
Typically the bootloader of an armadillo board does not support DT
so this option is useful.
* Do not disable SUSPEND
Suspend seems to work fine on the armadillo
* Enable PM_RUNTIME
This also seems to work fine.
* Move command line to dts
This brings us one small step closer to sharing defconfig
between armadillo and other boards
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
* Enable ARM_APPENDED_DTB
Typically the bootloader of a kzm9g board does not support DT
so this option is useful.
* Use voltage regulators by default
* Move command line to dts
This brings us one small step closer to sharing defconfig
between kzm9g and other boards
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
if_changed (used by the *.dts->*.dtc rule) rebuilds files if they aren't
contained in $(targets). (make V=2 indicates this). Add $(dtb-y) to
$(targets) to prevent *.dtb from always being rebuilt.
This fixes a regression introduced by the .dtb rule rework in 499cd82
"ARM: dt: change .dtb build rules to build in dts directory".
Reported-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
This patch adds necessary DT properties to m28evk to enable touchscreen
in the LRADC block. The M28EVK is shipped with 4-wire resistive touchscreen.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add pinctrl support for SSC on AT91 dtsi files.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
[nicolas.ferre@atmel.com: split dtsi and driver changes]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reluctantly-acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
- gpio fixes in mvebu, kirkwood, and dove
- small DT fix for mvebu (correct RAM size)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQ7xPtAAoJEAi3KVZQDZAeYBEH/0fxDNyDyRxxTYhf0FgfJpOW
kknx5d6XzL75HQCvFD0ObEkgmxkWNCnkUqU5ZglqGx7/P5yKs8K46IyG1LHF2mnL
4/TSJH7QOLTcI5DrLtvgbhLDQjqibtxGC0IGucbHxO/9unn8uk5xV7ax5++JcTQb
p8vhldxUa1QJu9og6SJRL+LJnI9PdcXpZELCdZOyPd62/9MNCb7uZwRRC0sIDk7N
0SsJ/81VUmq0o29WkZtWrxqPiUUzgsyAnC4anVeGjBn/PzcY63pzY4lpNEu94WLp
Ed9s8E/UcyltjcOHADWfOzNehGQjQwpVI9NdyOFgF/QMVJItHwfuXe1Rra9Qu50=
=8ARJ
-----END PGP SIGNATURE-----
Merge tag 'mvebu_fixes_for_v3.8-rc3' of git://git.infradead.org/users/jcooper/linux into fixes
From Jason Cooper:
mvebu fixes for v3.8-rc3
- gpio fixes in mvebu, kirkwood, and dove
- small DT fix for mvebu (correct RAM size)
* tag 'mvebu_fixes_for_v3.8-rc3' of git://git.infradead.org/users/jcooper/linux:
arm: mvebu: Fix memory size for Armada 370 DB
ARM: Dove: add Cubox sdhci card detect gpio
ARM: Kirkwood: fix ns2 gpios by converting to pinctrl
arm: mvebu: use global interrupts for GPIOs on Armada XP
* Enable ARM_APPENDED_DTB
Typically the bootloader of a mackerel board does not support DT
so this option is useful
* Add "rw" to command line
This appears to be necessary for a successful NFS-root boot
* Remove memchunk from kernel command line,
it is not used outside of arch/sh
* Move command line to dts
This brings us one small step closer to sharing defconfig
between mackerel and other boards
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
ARCH_HAS_DECOMP_WDOG is only used in lib/inflate.c which is not
included in arch/arm/boot/compressed/decompress.c now. That said,
ARCH_HAS_DECOMP_WDOG is not used at all. Let's remove it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Actually the Armada 370 DB (aka DB-88F6710-BP-DDR3) come with 1GB and
not 512MB.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Card detect for sdhci on Cubox is connected to the wrong pin
(sdio1_cd instead of sdio0_cd). With support for cd-gpios and
pinctrl add the corresponding properties to DT for Cubox.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Note that the pinctrl conversion also fixes GPIO support for ns2 boards.
Since commit f9e75922: "ARM: Kirkwood: Make use of mvebu pincltl and
gpio", the mvbu_gpio driver is used for DT boards. As mvbu_gpio relies
on the pinctrl driver, then a pinctrl definition must be given to allow
the GPIO configuration.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
People are back from the holiday breaks, and it shows. Here are a bunch of
fixes for a number of platforms:
- A couple of small fixes for Nomadik
- A larger set of changes for kirkwood/mvebu
- uart driver selection, dt clocks, gpio-poweroff fixups,
a few __init annotation fixes and some error handling improvement
in their xor dma driver.
- i.MX had a couple of minor fixes (and a critical one for flexcan2
clock setup)
- MXS has a small board fix and a framebuffer bugfix
- A set of fixes for Samsung Exynos, fixing default bootargs and some
Exynos5440 clock issues
- A set of OMAP changes including PM fixes and a few sparse warning
fixups
All in all a bit more positive code delta than we'd ideally want to see
here, mostly from the OMAP PM changes, but nothing overly crazy.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=s9fE
-----END PGP SIGNATURE-----
Merge tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"People are back from the holiday breaks, and it shows. Here are a
bunch of fixes for a number of platforms:
- A couple of small fixes for Nomadik
- A larger set of changes for kirkwood/mvebu
- uart driver selection, dt clocks, gpio-poweroff fixups, a few
__init annotation fixes and some error handling improvement in
their xor dma driver.
- i.MX had a couple of minor fixes (and a critical one for flexcan2
clock setup)
- MXS has a small board fix and a framebuffer bugfix
- A set of fixes for Samsung Exynos, fixing default bootargs and some
Exynos5440 clock issues
- A set of OMAP changes including PM fixes and a few sparse warning
fixups
All in all a bit more positive code delta than we'd ideally want to
see here, mostly from the OMAP PM changes, but nothing overly crazy."
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (44 commits)
ARM: clps711x: Fix bad merge of clockevents setup
ARM: highbank: save and restore L2 cache and GIC on suspend
ARM: highbank: add a power request clear
ARM: highbank: fix secondary boot and hotplug
ARM: highbank: fix typos with hignbank in power request functions
ARM: dts: fix highbank cpu mpidr values
ARM: dts: add device_type prop to cpu nodes on Calxeda platforms
ARM: mx5: Fix MX53 flexcan2 clock
ARM: OMAP2+: am33xx-hwmod: Fix wrongly terminated am33xx_usbss_mpu_irqs array
pinctrl: mvebu: make pdma clock on dove mandatory
ARM: Dove: Add pinctrl clock to DT
dma: mv_xor: fix error handling for clocks
dma: mv_xor: fix error handling of mv_xor_channel_add()
arm: mvebu: Add missing ; for cpu node.
arm: mvebu: Armada XP MV78230 has only three Ethernet interfaces
arm: mvebu: Armada XP MV78230 has two cores, not one
clk: mvebu: Remove inappropriate __init tagging
ARM: Kirkwood: Use fixed-regulator instead of board gpio call
ARM: Kirkwood: Fix missing sdio clock
ARM: Kirkwood: Switch TWSI1 of 88f6282 to DT clock providers
...
From Kukjin Kim:
Most of them are EXYNOS5440 fixes which are for changing uart console,
cpu id (typo) and silent complaining gpio error in kernel boot.
* 'v3.8-samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: skip the clock initialization for exynos5440
ARM: EXYNOS: enable PINCTRL for EXYNOS5440
ARM: dts: use uart port1 for console on exynos4210-smdkv310
ARM: dts: use uart port0 for console on exynos5440-ssdk5440
ARM: SAMSUNG: fix the cpu id for EXYNOS5440
ARM: EXYNOS: Revise HDMI resource size
is unresponsive for quite a while. People start complaining the missing
of such an important fix.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQ7DwYAAoJEFBXWFqHsHzOHnUH/2V7EKzq8g6FH5DyOf3+9x9f
I+KyjVusIFdbLIJZhswbTnd2f1k5FQnQ+djd6fERi/wZ8IcG70vPRscKIYrLX6po
gd0z684ORsBwNrHMfcKSY6DwZF2cLtP5BpyvtQzKHpP3nTYBgE7ePSFlfsAdJ5OG
C77/tj61B/bUe0Mm8ygjMCwYsdqaR2+MTdEcStvOmwd4x+PBT3uSd56TFhXW2kt5
Py2d48wowncNM5CVIW7vvH4kaaCW4h6mxnc3gyc8YS8h1JFItdYFSNUzT9Mb5ene
aM3He/pp82OoXm84Swhi5Ah5566WVor+bgnvJ1TmV4Q/yd6Cn+MA2nIOevTnJvo=
=Tjtj
-----END PGP SIGNATURE-----
Merge tag 'mxs-fixes-3.8' of git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo:
I have to send one critical mxsfb fix through arm-soc, as FB maintainer
is unresponsive for quite a while. People start complaining the missing
of such an important fix.
* tag 'mxs-fixes-3.8' of git://git.linaro.org/people/shawnguo/linux-2.6:
video: mxsfb: fix crash when unblanking the display
ARM: dts: imx23-olinuxino: Fix IOMUX settings
when the port gets brought up. The other two are non-critical fixes,
which are sent together here, since it's still early -rc stage.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQ7Dk+AAoJEFBXWFqHsHzOUugIAJZblDy7ORFZhW0R8L4Be541
pS5aBGFY7VYCrL9BGUKGsLuITI+arbYFHc+H4nqhNMBAvgChPxJZMnaG4kp1Q5Vm
AVr9tNrwsauVHLlryUk4ekut4G4WWo1NDcFq4S6rxD/jxA/uP6rnMUCY6PX4LLL9
ZpGDb3BWQ2bbUaANu3cjc1I1/Gle1ir9LObm6ZC6l8MHTTG7hyTMHvS8eCZzmDbc
9z01ZrvTKn1AneeHOpArd2/jo14b6Kap8ykx2hdVUeBhIbZp3pomezZau9ya8/kB
+1BQVODdkOMzBm6gkIkfU3HbUPnIPL18MG/uKyD+f67YkX5YODinUVdq63upLxc=
=7yrS
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-3.8' of git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo:
It includes one critical fix - wrong flexcan2 clock will hang system
when the port gets brought up. The other two are non-critical fixes,
which are sent together here, since it's still early -rc stage.
* tag 'imx-fixes-3.8' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: mx5: Fix MX53 flexcan2 clock
ARM: dts: imx31-bug: Fix manufacturer compatible string
clk: imx: Remove 'clock-output-names' from the examples
The Armada XP GPIO controller has two ways of notifying interrupts:
using global interrupts or using per-CPU interrupts. In an attempt to
use the best available features, the 'marvell,armadaxp-gpio'
compatible string selects a variant of the gpio-mvebu driver that
makes use of the per-CPU interrupts.
Unfortunately, this doesn't work properly in a SMP context, because we
fall into cases where the GPIO interrupt is enabled on CPU X at the
GPIO controller level, but on CPU Y at the interrupt controller
level. It is not yet clear how to fix that easily.
So for 3.8, our approach is to switch to global interrupts for GPIOs,
so that we do not fall into this per-CPU interrupts problem.
This patch therefore fixes GPIO interrupts on Armada XP
platforms. Without this patch, GPIO interrupts simply do not work
reliably, because their proper operation depends on which CPU the code
requesting the interrupt is running.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds dw_dmac's platform data to DT node. It also creates slave info
node for SPEAr13xx, for the devices which were using dw_dmac.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
- use correct uart driver for mvebu boards
- add a missing DT clocks
- gpio-poweroff level vs. edge triggering, use gpio_is_valid()
- remove an inappropriate __init, modules need to access function.
- various DT fixes
- error handling in mv_xor
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQ6vYDAAoJEAi3KVZQDZAeoHwIAKSw+8B601AixTZus7fp9wrE
M9Tk4VoCflDQ8uIh6sHrHQlwMi8NPVA6ogn6VoEYA7HnA/nGTx/Ij/XCpuPBdt8+
VM5gzonaKK16OswtLmUZIgJKDJt0Q+zw9K7u6UkWQW8IXyGlyK2gxYqJLQPHhebb
D3TyKdJqx7FBr2Oq3MJQshIN/TTSOA+q94oYUogc7qZpjsY8ZgnBbRWVBYEhRa+u
sS0vZ8LV5twOKqATJa4ZCXA4E3WoKOZKTgdXj4IRfRkeQh9WHmhH4aWwq7Kl72Ic
glBA6iCrA/6KvJx9H4AG5BK/Ltg2vfQDKo2XWMQtH8j2WwHfMqHMPS3qivjXg2s=
=jfqF
-----END PGP SIGNATURE-----
Merge tag 'mvebu_fixes_for_v3.8' of git://git.infradead.org/users/jcooper/linux into fixes
From Jason Cooper:
fixes for mvebu/kirkwood v3.8
- use correct uart driver for mvebu boards
- add a missing DT clocks
- gpio-poweroff level vs. edge triggering, use gpio_is_valid()
- remove an inappropriate __init, modules need to access function.
- various DT fixes
- error handling in mv_xor
* tag 'mvebu_fixes_for_v3.8' of git://git.infradead.org/users/jcooper/linux:
pinctrl: mvebu: make pdma clock on dove mandatory
ARM: Dove: Add pinctrl clock to DT
dma: mv_xor: fix error handling for clocks
dma: mv_xor: fix error handling of mv_xor_channel_add()
arm: mvebu: Add missing ; for cpu node.
arm: mvebu: Armada XP MV78230 has only three Ethernet interfaces
arm: mvebu: Armada XP MV78230 has two cores, not one
clk: mvebu: Remove inappropriate __init tagging
ARM: Kirkwood: Use fixed-regulator instead of board gpio call
ARM: Kirkwood: Fix missing sdio clock
ARM: Kirkwood: Switch TWSI1 of 88f6282 to DT clock providers
Power: gpio-poweroff: Fix documentation and gpio_is_valid
ARM: Kirkwood: Fix missing clk for USB device.
arm: mvebu: Use dw-apb-uart instead of ns16650 as UART driver
Signed-off-by: Olof Johansson <olof@lixom.net>
With the addition of commit a0ae0240 (ARM: kernel: add device tree init
map function), the cpu reg values must match the cpu mpidr register or we'll
get warnings. For some reason, the CLUSTERID on highbank is 9, so the reg
value needs to be 0x90n to quiet the warnings.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
While device_type is considered deprecated, it is still needed for tools
like lshw to identify cpu nodes.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The second FlexCAN port uses different clock than the first one, configure
correct clock to prevent hanging of the system during bringing up of the port.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
During merge of the mvebu patches a clock gate for pinctrl was
lost. This patch just readds the clock gate.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Armada XP MV78230 DT include file is missing a ; at the
end of the cpu node.
Reported-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
We originally thought that the MV78230 variant of the Armada XP had
four Ethernet interfaces, like the other variants MV78260 and
MV78460. In fact, this is not true, and the MV78230 has only three
Ethernet interfaces.
So, the definitions of the Ethernet interfaces is now done as follows:
* armada-370-xp.dtsi: definitions of the first two interfaces, that
are common to Armada 370 and Armada XP
* armada-xp.dtsi: definition of the third interface, common to all
Armada XP variants.
* armada-xp-mv78260.dtsi and armada-xp-mv78460.dtsi: definition of
the fourth interface.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Contrary to our understanding at the time armada-xp-mv78230.dtsi was
written, the MV78230 variant of the Armada XP SoC has two cores and
not one. This patch updates the .dtsi file to take into account this
reality.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
With the change to a DT based pinctrl/gpio driver, using gpio API
calls in board-*.c files no longer works, a dereferenced NULL pointer
exception occurs instead. By converting the GPIO code into a
fixed-regulator which gets probed later once pinctrl/gpio is
available, we avoid the exception.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Stefan Peter <s.peter@mplch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Clock Management of kirkwood has moved to DT clock providers.
However, TWSI1 has not yet been done.
This switches TWSI1 of 88f6282 to DT clock providers.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Without the clock being held by a driver, it gets turned off at a bad
time causing the SoC to lockup. This is often during reboot.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Stefan Peter <s.peter@mpl.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
