Replace printk calls with dev_xxx calls. Set the 'dev' field of the codec
and codec_dai structures so that these calls work.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix a oversight in the CS4270 codec driver that caused a build break.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
MIDI_TX IRQ seems always pending when any bytes on FIFO is available.
Thus, it's better to enable MPU_TX only when any bytres are really
stored in the substream, and disables immediately when the queue
becomes empty.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
omap_pcm_trigger is called also in interrupt context so CPU flags must
be restored when returning.
Signed-off-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com>
Acked-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Volume-knob widgets have no widget selection although they have widget
connections. Thus, the connection list in the proc output shouldn't
contain the selection (*).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The missing module license generates warning
during module loading.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
With a postfix decrement time will reach -1 rather than 0,
so the warning will not be issued.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Update pandora board file for recent TWL4030 codec changes.
Also move output related snd_soc_dapm_nc_pin() calls to
omap3pandora_out_init(), where they belong.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Spruce up the documentation in the CS4270 codec. Use kerneldoc where
appropriate. Fix incorrect comments.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The ess1688 driver uses the same port
for PCM audio (SB compatible) and OPL3
synthesis. It is not always right so allow to
choose a different port for OPL3 synthesis.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASoC codec drivers typically serve two masters: the I2C bus and ASoC itself.
When a codec driver registers with ASoC, a probe function is called. Most
codec drivers call ASoC first, and then register with the I2C bus in the ASoC
probe function.
However, in order to support multiple codecs on one board, it's easier if the
codec driver is probed via the I2C bus first. This is because the call to
i2c_add_driver() can result in the I2C probe function being called multiple
times - once for each codec. In the current design, the driver registers
once with ASoC, and in the ASoC probe function, it calls i2c_add_driver().
The results in the I2C probe function being called multiple times before the
driver can register with ASoC again.
The new design has the driver call i2c_add_driver() first. In the I2C probe
function, the driver registers with ASoC. This allows the ASoC probe function
to be called once per I2C device.
Also add code to check if the I2C probe function is called more than once,
since that is not supported with the current ASoC design.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
X86_PC is the only remaining 'sub' architecture, so we dont need
it anymore.
This also cleans up a few spurious references to X86_PC in the
driver space - those certainly should be X86.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In the case of having a selector instead of mixer while initing input
sources, the case that happens with ALC889, we must select instead
of muting input. Problem was found while testing with hda-emu.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the analog loopback/bypass support for twl4030 codec.
Details for the implementation:
It seams that the analog loopback needs the DAC powered on on the channel,
where the loopback is selected. The switch for the DACs has been moved from
the DAPM_DAC to the "Analog XX Playback Mixer". In this way the DAC will be
powered while the audio playback is used or/and the loopback is enabled for
the channel.
The twl4030 codec powering has been reworked. Now the codec will be powered as
long as it does not receives the SND_SOC_BIAS_OFF event. The exceptions are
when the given change in the registers needs the codec power down/up cycle in
order to take effect. Otherwise the codec is on.
When the codec enters to STANDBY state and none of the loopback paths are
enabled, than the amplifiers, which are no in the DAPM path are forced to turn
off and the PLL is disabled. When playback/capture starts the disabled gains
are restored and the PLL is enabled.
When one of the loopback enabled in STANDBY mode, the disabled gains are
restored and the PLL is enabled also.
In short: the codec always goes to the lowest power state based on the
bias_level and the bypass_state.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch explicitly initializes McBSP Transmit Configuration
Control Register (XCCR) and Receive Configuration Control
Register (RCCR) to their reset values. Reset values are 26 ns
of DX delay and Transmit DMA disabled for XCCR register;
receive full cycle mode enabled and Receive DMA disabled for
RCCR register.
This patch requires a counterpart in OMAP McBSP driver before
to apply it. The required changes in McBSP were sent and approved
in linux-omap mailing list and patch is going upstream
(commit 3127f8f859 from linux-omap-2.6
tree).
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
[ jarkko.nikula@nokia.com: Commit id for counterpart patch corrected ]
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8753 driver multiplexes the DAI structures it exposes to the
outside world, leaving them uninitialised until the codec probes. Since
the DAI name is used during the registration and setup process provide a
dummy name.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
While debugging some code paths in AC97 codec patches and its suspend
and resume functions, getting to know the flags has proved useful to
follow those code paths.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently code for capture source support in ALC889 only considers
capture mixers. This change adds additional support for ADC+selector
present in ALC889, taking into account also the presence of an
additional DMIC connection item in the selector.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Check in a quirk list if it should do cold reset when AC97 power saving
is enabled. Some devices do not resume properly when cold reset,
although power saving works OK.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add another MacBook Pro 4,1 SSID (106b:3800). It seems that latter revisions,
(at least mine), have different IDs to earlier revisions.
Signed-off-by: Luke Yelavich <themuso@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is driver for Turtle Beach Multisound cards:
Classic, Fiji and Pinnacle.
Tested pcm playback and recording and MIDI playback
on Multisound Pinnacle.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move the twl4030_power_up and twl4030_power_down function
earlier to facilitate the analog bypass implementation.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Change the power switches for the physical ADC and for the
amplifiers for the analog capture path to map more closely
the actual path inside of the codec.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The Headset Left anti-pop and bias ramp does not need to be
enabled, if the headset is not in use.
Move the code to DAPM event handler for HeadsetL.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Merge the codec up and down functions to a simple one.
Codec is powered down by default (reg_cache change).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The offset cancelation bit in ANAMICL register is self cleanig.
Make sure that the reg_cache holds the same value as the HW
register.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rather use printf format instead of hardcoding prefix like 0x.
A next step would be to predefine certain formats.
Signed-off-by: Andreas Bergmeier <lcid-fire@gmx.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Distribute the packets evenly among the URBs, instead of making all URBs
except the last one to have the maximum size. This makes the timing of
pointer updates more regular and removes some special cases from the
code.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Once our URBs contain enough packets, queueing more URBs does not give
us any additional underrun protection (as we use double-buffering) but
just increases latency unnecessarily. Therefore, we try to limit the
queue length to some reasonable value.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When sending a silence URB (before playback has started, or when it is
paused), use the number of frames that would be normally sent instead of
a single frame so that the rate at which completion interrupts arrive is
consistent.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some revisions of the 92hd71xxx codec families don't have input amps
on ports 0xa, 0xd and 0xf, so probe the widget caps on port 0xa and
check for support, if found run snd_hda_sequence_write_cache() on the
stac92hd71xxx_unmute_core_init verb list.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Further improvements in the I2C initialization sequence of the CS4270 driver.
All ASoC initialization is now done in the I2C probe function.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
