This splits off a 'pci-new.c' which is aimed at gradually replacing the
pci-auto backend and the arch/sh/drivers/pci/pci.c core respectively.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The new PCI code wants its own bus<->resource mappings instead of the
generic equivalents, so drop the asm-generic include in preparation.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Take already available policy->cpuinfo.max_freq and get rid of acpi-cpufreq
specific max_freq variable.
This implies that P0 is always the highest frequency which should always
be true as ACPI spec says:
As a result, the zeroth entry describes the highest performance state
Signed-off-by: Thomas Renninger <trenn@suse.de>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
As a result of an off-by-1 error pcm990 leaves one unused GPIO number between
built-in GPIOs and the pca9536 extender. Fix it.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Firstly, this patch makes the palm27x asoc driver a little more sane. Also,
since all affected devices use GPIO95 as AC97_nRESET, this patch sets that
properly. Affected are PalmT5, TX and LifeDrive.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Fixes guest crash 'lguest: bad read address 0x4800000 len 256'
The new per-cpu allocator ends up handing a non-linear address to
write_gdt_entry. We do __pa() on it, and hand it to the host, which
kills us.
I've long wanted to make the hypercall "LOAD_GDT_ENTRY" to match the IDT
code, but had no pressing reason until now.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: lguest@ozlabs.org
A caller (do_boot_cpu) already has __cpuinit attribute.
Since HOTPLUG_CPU depends on SMP && HOTPLUG it doesn't
lead to panic at moment.
[ Impact: cleanup ]
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
LKML-Reference: <20090418194528.GD25510@lenovo>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Currently, when x2apic is not enabled, interrupt remapping
will be enabled in init_dmars(), where it is too late to remap
ioapic interrupts, that is, ioapic interrupts are really in
compatibility mode, not remappable mode.
This patch always enables interrupt remapping before ioapic
setup, it guarantees all interrupts will be remapped when
interrupt remapping is enabled. Thus it doesn't need to set
the compatibility interrupt bit.
[ Impact: refactor intr-remap init sequence, enable fuller remap mode ]
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Weidong Han <weidong.han@intel.com>
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: allen.m.kay@intel.com
Cc: fenghua.yu@intel.com
LKML-Reference: <1239957736-6161-4-git-send-email-weidong.han@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Shouldn't call ack_apic_edge() in ir_ack_apic_edge(), because
ack_apic_edge() does more than just ack: it also does irq migration
in the non-interrupt-remapping case. But there is no such need for
interrupt-remapping case, as irq migration is done in the process
context.
Similarly, ir_ack_apic_level() shouldn't call ack_apic_level, and
instead should do the local cpu's EOI + directed EOI to the io-apic.
ack_x2APIC_irq() is not neccessary, because ack_APIC_irq() will use MSR
write for x2apic, and uncached write for non-x2apic.
[ Impact: simplify/standardize intr-remap IRQ acking, fix on !x2apic ]
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Weidong Han <weidong.han@intel.com>
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: allen.m.kay@intel.com
Cc: fenghua.yu@intel.com
LKML-Reference: <1239957736-6161-3-git-send-email-weidong.han@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Use plat_early_device_setup() to register Early Platform Data
for SuperH Mobile processors.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add a plat_early_device_setup() function to allow
processor-specific code to register Early Platform Data.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Extend the 32-bit SuperH timer code to register and probe
the earlytimer class of Early Platform Drivers.
This registers the sh_cmt driver if compiled-in.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
I hit the check_flags error of lockdep:
WARNING: at kernel/lockdep.c:2893 check_flags+0x1a7/0x1d0()
[...]
hardirqs last enabled at (12567): [<ffffffff8026206a>] local_bh_enable+0xaa/0x110
hardirqs last disabled at (12569): [<ffffffff80610c76>] int3+0x16/0x40
softirqs last enabled at (12566): [<ffffffff80514d2b>] lock_sock_nested+0xfb/0x110
softirqs last disabled at (12568): [<ffffffff8058454e>] tcp_prequeue_process+0x2e/0xa0
The check_flags warning of lockdep tells me that lockdep thought interrupts
were disabled, but they were really enabled.
The numbers in the above parenthesis show the order of events:
12566: softirqs last enabled: lock_sock_nested
12567: hardirqs last enabled: local_bh_enable
12568: softirqs last disabled: tcp_prequeue_process
12566: hardirqs last disabled: int3
int3 is a breakpoint!
Examining this further, I have CONFIG_NET_TCPPROBE enabled which adds
break points into the kernel.
The paranoid_exit of the return of int3 does not account for enabling
interrupts on return to kernel. This code is a bit tricky since it
is also used by the nmi handler (when lockdep is off), and we must be
careful about the swapgs. We can not call kernel code after the swapgs
has been performed.
[ Impact: fix lockdep check_flags warning + self-turn-off ]
Acked-by: Peter Zijlsta <a.p.zijlstra@chello.nl>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* master.kernel.org:/home/rmk/linux-2.6-arm: (48 commits)
[ARM] S3C24XX: ADC: Check pending queue before freeing adc client
[ARM] S3C: Fix ADC driver sparse warning
[ARM] Osiris: Fix double initialisation in machine block
[ARM] Anubis: Fix sparse warnings for items that should be static
[ARM] JIVE: Fix sparse warnings about items which should be static
[ARM] S3C: Fix sparse warning from missing 's3c_device_hwmon'
[ARM] S3C24XX: Fix sparse error in gpiolib.c
[ARM] 5455/1: Fix IRQ noise from VIC code
[ARM] 5454/1: ep93xx_eth: fix sparse warnings
[ARM] remove .gitignore from include/asm-arm
Update MAINTAINERS
mxc defconfig updates
mx31ads: Mark as having full regulatoion constraints with 1133-EV1 board
mx31ads: Depend on all the WM8350 core dependencies for WM1133-EV1 board
Fix ifdef in plat-mxc/irc.c
MX1ADS: remove I2C ifdefs
qong: remove AIPS[12] mappings from machine-specific iotable
mx31ads: imoux pins should be passed in as unsigned int
MXC: remove orphan imx_init_uart() definition
mx31: pin definition for csi
...
calculate_numa_remap_pages() is called only by __init initmem_init()
further calculate_numa_remap_pages is calling:
__init find_e820_area() and __init reserve_early()
So calculate_numa_remap_pages() should be __init calculate_numa_remap_pages().
WARNING: arch/x86/built-in.o(.text+0x82ea3): Section mismatch in reference from the function calculate_numa_remap_pages() to the function .init.text:find_e820_area()
The function calculate_numa_remap_pages() references
the function __init find_e820_area().
This is often because calculate_numa_remap_pages lacks a __init
annotation or the annotation of find_e820_area is wrong.
WARNING: arch/x86/built-in.o(.text+0x82f5f): Section mismatch in reference from the function calculate_numa_remap_pages() to the function .init.text:reserve_early()
The function calculate_numa_remap_pages() references
the function __init reserve_early().
This is often because calculate_numa_remap_pages lacks a __init
annotation or the annotation of reserve_early is wrong.
[ Impact: save memory, address Section mismatch warning ]
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
LKML-Reference: <1239991281.3153.4.camel@ht.satnam>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
It is common to use "make install" in restricted environments which
differ from the one which was actually used to build the kernel. In
such environments it is highly undesirable to trigger a rebuild of any
part of the system. Worse, the rebuild may be spurious, triggered by
differences in the environment.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
LKML-Reference: <20090415234642.GA28531@uranus.ravnborg.org>
Fix an endcase in the UV initialization code for the "UV large system mode"
of apicids. If node zero contains no cpus, cpus on another node will be the
boot cpu. The percpu data that contains the extra apicid bits was not
being initialized early enough.
[ Impact: fix potential boot crash on cpu-less UV nodes ]
Signed-off-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <20090417142447.GA23759@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add support for nodes that have cpus but no memory.
The current code was failing to add these nodes
to the nodes_present_map.
v2: Fixes case caught by David Rientjes - missed support
for the x2apic SRAT table.
[ Impact: fix potential boot crash on memory-less UV nodes. ]
Reported-by: David Rientjes <rientjes@google.com>
Signed-off-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <20090417142242.GA23743@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This renames include/asm-h8300/timer.h into arch/h8300/include/asm: it
was left over just because that file had been created in the -mm tree
before the whole h8300 header subdirectory had been moved, and then got
merged in the old location afterwards.
(See commits e0b0f9e4ea: "h8300: update
timer handler - new files" and 758db3f211:
"[h8300] move include/asm-h8300 to arch/h8300/include/asm" for details).
This also removes a left-over .gitignore file in include/asm-arm that
became stale when the ARM header files were moved (which happened in
multiple commits, just see "git log -- include/asm-arm" for details).
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://www.linux-m32r.org/git/takata/linux-2.6_dev:
m32r: move include/asm-m32r/* to arch/m32r/include/asm/
m32r: move include/asm-m32r headers to arch/m32r/include/asm
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: fix microcode driver newly spewing warnings
x86, PAT: Remove page granularity tracking for vm_insert_pfn maps
x86: disable X86_PTRACE_BTS for now
x86, documentation: kernel-parameters replace X86-32,X86-64 with X86
x86: pci-swiotlb.c swiotlb_dma_ops should be static
x86, PAT: Remove duplicate memtype reserve in devmem mmap
x86, PAT: Consolidate code in pat_x_mtrr_type() and reserve_memtype()
x86, PAT: Changing memtype to WC ensuring no WB alias
x86, PAT: Handle faults cleanly in set_memory_ APIs
x86, PAT: Change order of cpa and free in set_memory_wb
x86, CPA: Change idmap attribute before ioremap attribute setup
Currently the numa_node attribute for these PCI devices is 0 (it
corresponds to the numa_node for PCI bus 0). This is not a big issue
but incorrect.
This inconsistency can be fixed by reading the node number from CPU
NB function 0.
[ Impact: fill in dev->numa_node information, to optimize DMA allocations ]
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: jbarnes@virtuousgeek.org
LKML-Reference: <20090417100746.GG16198@alberich.amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Check pending queue and remove the adc client being released.
Signed-off-by: Ramax Lo <ramaxlo@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The symbol 's3c_adc_try' in arch/arm/plat-s3c24xx/adc.c
does not need to be exported and thus should be static.
This fixes the following sparse warning:
adc.c:103:6: warning: symbol 's3c_adc_try' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The .init_machine entry in mach-osiris.c had the same entry
twice, so remove one definition to fix the following warning
from sparse:
mach-osiris.c:416:3: warning: Initializer entry defined twice
mach-osiris.c:418:3: also defined here
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Make 'anubis_ide_platdata' statis as it is not used outside
the file it is in, fixing the following sparse warning:
mach-anubis.c:246:27: warning: symbol 'anubis_ide_platdata' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Make 'jive_vgg2432a4_display' and 'jive_lcd_config' static as
they are not exported, and are generating the following sparse
warnings:
mach-jive.c:280:26: warning: symbol 'jive_vgg2432a4_display' was not declared. Should it be static?
mach-jive.c:313:28: warning: symbol 'jive_lcd_config' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix the following sparse warning due to s3c_device_hwmon being
missing from <plat/devs.h>
devs.c:380:24: warning: symbol 's3c_device_hwmon' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix the following sparse error generated by including
<plat/gpio-core.h> instead of <mach/gpio-core.h>
gpiolib.c:78:22: warning: symbol 's3c24xx_gpios' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This starts moving out the common initialization bits from the various
fixup paths in to the shared init path.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that the platform code is a bit leaner, we can start consolidating
the various IRQ routing implementations. There are effectively only 2
variants, and the others can use those directly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Commit 68b42d1b54 ("sh: sh7785lcr: Map
whole PCI address space.") changed around the semantics of how various
chip-selects are made accessible to PCI. Now that there is a single
large mapping covering from CS0-CS6, there is no longer any need to
do multi-window mapping. Subsequently, all of the differing
implementations can be consolidated in to pci-sh7780.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This consolidates all of the PCI I/O and memory window definitions across
the pci-sh7780 users in pci-sh7780 itself. No functional changes, in that
every platform had exactly the same implementation.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently the I/O port base isn't being set anywhere, which allows things
like generic_inl() to blow up. Fix this up to point at the PCI IO window.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The SH7780 PCIC contains a read-only cache line size register that we can
derive pci_cache_line_size from. So, make sure that the software idea of
the cache line size actually matches the host controller's idea.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Don't use pci_write_reg() for these, as it defaults to 32-bit. Rather
than using the helper, use __raw_writeb() directly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This reworks how the host controller is probed, and makes it a bit more
verbose in the event a new type of controller is detected. Additionally,
we also log the revision information.
This now uses the proper access sizes for the vendor/device registers,
rather than relying on a larger access that encapsulated both of them.
Not all devices support 32-bit read cycles for these registers.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
