As noted by Russell King, the sleep code path is not
elegant and makes use of leaving items on the stack
between calls.
Change the code that does the following:
if (s3c_cpu_save(regs_save) == 0) {
flush_cache_all();
S3C_PMDBG("preparing to sleep\n");
pm_cpu_sleep();
}
to simply call s3c_cpu_save, and let that do the
necessary calls to quiesce and sleep the system.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Impact: __per_cpu_load available on all SMP capable archs
Percpu now requires three symbols to be defined - __per_cpu_load,
__per_cpu_start and __per_cpu_end. There were three archs which
didn't have it. Update them as follows.
* powerpc: can use generic PERCPU() macro. Compile tested for
powerpc32, compile/boot tested for powerpc64.
* ia64: can use generic PERCPU_VADDR() macro. __phys_per_cpu_start is
identical to __per_cpu_load. Compile tested and symbol table looks
identical after the change except for the additional __per_cpu_load.
* arm: added explicit __per_cpu_load definition. Currently uses
unified .init output section so can't use the generic macro. Dunno
whether the unified .init ouput section is required by arch
peculiarity so I left it alone. Please break it up and use PERCPU()
if possible.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Pat Gefre <pfg@sgi.com>
Cc: Russell King <rmk@arm.linux.org.uk>
The definitions of S3C2412_IISMOD_SDF_MSB and S3C2412_IISMOD_SDF_LSB
are incorrect, being the same S3C2412_IISMOD_SDF_IIS which is the
only correct one in this series.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (29 commits)
p54: fix race condition in memory management
cfg80211: test before subtraction on unsigned
iwlwifi: fix error flow in iwl*_pci_probe
rt2x00 : more devices to rt73usb.c
rt2x00 : more devices to rt2500usb.c
bonding: Fix device passed into ->ndo_neigh_setup().
vlan: Fix vlan-in-vlan crashes.
net: Fix missing dev->neigh_setup in register_netdevice().
tmspci: fix request_irq race
pkt_sched: act_police: Fix a rate estimator test.
tg3: Fix 5906 link problems
SCTP: change sctp_ctl_sock_init() to try IPv4 if IPv6 fails
IPv6: add "disable" module parameter support to ipv6.ko
sungem: another error printed one too early
aoe: error printed 1 too early
net pcmcia: worklimit reaches -1
net: more timeouts that reach -1
net: fix tokenring license
dm9601: new vendor/product IDs
netlink: invert error code in netlink_set_err()
...
The remaining registers are separated into:
- <mach/regs-ost.h>
- <mach/regs-rtc.h>
- <mach/regs-intc.h>
and then we can remove pxa-regs.h completely. Instead of #include this
file, let's:
1. include the specific <mach/regs-*.h> with care (if that's absolutely
necessary)
2. define the registers in the driver, make cleanly defined API to expose
the register access to external with sufficient reason
Signed-off-by: Eric Miao <eric.miao@marvell.com>
The definitions of PXA_CS<x>_PHYS are really PXA2xx specific and should
be moved out of pxa-regs.h. As an illustration, the PXA3xx static chip
selects definitions are added into pxa3xx-regs.h.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
This isn't perfect but at least solves the problem of pm.c's dependency
on register definitions in <mach/lubbock.h>, which doesn't make much
sense.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Move the processor specific initialization (largely resources initialization)
out of soc_common_drv_pcmcia_probe() into dedicated sa11xx_drv_pcmcia_probe()
and __pxa2xx_drv_pcmcia_probe().
By doing this, we are now able to move the PCMCIA related definitions out of
pxa-regs.h and back into pxa2xx_base.c.
As a result, remove that reference of _PCMCIA1IO in arch/arm/mach-pxa/viper.c.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
pxa-regs.h and hardware.h are not intended for use directly in driver
code, remove those unnecessary references.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Let's handle GPIOs by banks, each bank covers up to 32 GPIOs with one set
of registers, and each set of registers start from different offsets.
GPLR GPDR GPSR GPCR GRER GFER GEDR
BANK 0 - 0x0000 0x000C 0x0018 0x0024 0x0030 0x003C 0x0048
BANK 1 - 0x0004 0x0010 0x001C 0x0028 0x0034 0x0040 0x004C
BANK 2 - 0x0008 0x0014 0x0020 0x002C 0x0038 0x0044 0x0050
BANK 3 - 0x0100 0x010C 0x0118 0x0124 0x0130 0x013C 0x0148
BANK 4 - 0x0104 0x0110 0x011C 0x0128 0x0134 0x0140 0x014C
BANK 5 - 0x0108 0x0114 0x0120 0x012C 0x0138 0x0144 0x0150
NOTE:
BANK 3 is only available on PXA27x and later processors.
BANK 4 and 5 are only available on PXA935
1. introduce GPIO_BANK(n) for the offset base of each bank
2. 'struct pxa_gpio_chip' is expanded to include IRQ edge and mask
setings, and saved register values as well, and is dynamically
allocated due to possible bank number ranging from 3 to 6
3. all accesses to GPIO registers are made through 'regbase' within
'pxa_gpio_chip', and register offset
4. introduce several inline functions to simplify the code a bit
5. change IRQ demux handler to base on gpio chips
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
This makes gpio.c fully independent of pxa-regs.h (except for the
virtual address of the registers).
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Looks like we have to live with pxa_gpio_mode() for a while, giving
its presence is actually making gpio.c not generic enough, let's
move it temporarily outside before it can be fully purged.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
This is part of the work making gpio.c generic enough, the changes
include:
1. move IRQ handling of GPIO 0 and 1 outside (and back into irq.c)
2. pxa_init_gpio() accepts a range for muxed GPIO IRQs, and an IRQ
number for the muxed GPIOs
3. __gpio_is_occupied() and __gpio_is_inverted() are made inline,
and are moved into <mach/gpio.h> instead of generic gpio.c
Signed-off-by: Eric Miao <eric.miao@marvell.com>
1. Driver code where pxa_request_dma() is called will most likely
reference DMA registers as well, and it is really unnecessary
to include pxa-regs.h just for this. Move the definitions into
<mach/dma.h> and make relevant drivers include it instead of
<mach/pxa-regs.h>.
2. Introduce DMAC_REGS_VIRT as the virtual address base for these
DMA registers. This allows later processors to re-use the same
IP while registers may start at different I/O address.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Considering the header mess ATM, it is not always possible to include
the correct header files within board code. Let's keep this simple:
<mach/pxa25x.h> - for pxa25x based platforms
<mach/pxa27x.h> - for pxa27x based platforms
<mach/pxa300.h> - for pxa300 based platforms
<mach/pxa320.h> - for pxa320 based platforms
<mach/pxa930.h> - for pxa930 based platforms
NOTE:
1. one header one board file, they are not compatible (i.e. they have
conflicting definitions which won't compile if included together).
2. Unless strictly necessary, the following header files are considered
to be SoC files use _only_, and is not recommended to be included in
board code:
<mach/hardware.h>
<mach/pxa-regs.h>
<mach/pxa2xx-regs.h>
<mach/pxa3xx-regs.h>
<mach/mfp.h>
<mach/mfp-pxa2xx.h>
<mach/mfp-pxa25x.h>
<mach/mfp-pxa27x.h>
<mach/mfp-pxa3xx.h>
<mach/mfp-pxa300.h>
<mach/mfp-pxa320.h>
<mach/mfp-pxa930.h>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Default to the same behaviour as the shipped WinCE system.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
The PM CRC checking code kmallocs an area to save a set of
CRC values during suspend. This triggers a warning due to the
call of a function that might sleep whilst the system is not
in a valid state to do so.
Move the allocation and free to points in the suspend and resume
process where they can call a function that might-sleep.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
When doing the CRC check of the memory, avoid checking
the page that our stack is residing in as this changes
during the execution of the suspend and resume.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add the definition for S3C_GPIO_END to allow the PM code to build.
This means moving the GPIO bank numbers to a separate file to allow
the gpio and regs-gpio to include them. Including regs-gpio.h into
gpio.h causes too many build problems and adding gpio.h would mean
editing a large number of files.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Change the way the UART state is saved over suspend to allow the s3c64xx
code to modify the settings on resume to avoid any illegal state changes
to the UART clocks. This will also allow us to save the UDIVSLOT register
on newer SoCs.
Move to using a structure for the UART use the extant Kconfig configuration
specifying the number of UARTs.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Rename s3c2410_cpu_resume to s3c_cpu_resume and s3c2410_cpu_save to
s3c_cpu_save to remove the CPU specific naming of these functions
which are now in the generic PM code.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Since we have moved a large proportion of the PM code to the common
support area, remove the cpu specific name from the initialisation
function.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
There's a bug in calculation of IRQ_EINT_BIT introduced on the test
branch for pm changes for s3c by Ben Dooks fixed in this patch.
There's also a bit of a mystery about how wake gets to wake EINT
set of interrupts, I added a couple of lines that make it work for
EINT4+ but not sure what's meant to be there for EINT0-3.
Still, this gets GTA02 resume working again.
Signed-off-by: Andy Green <andy@openmoko.com>
[ben-linux@fluff.org: remove irq-pm.c change]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the IRQ_EINT sleep control to be available to all
s3c impelmentations. Since s3c_irqext_wake is not large,
place it in arch/arm/plat-s3c/pm.c as adding it to a new
file would be a waste of compile time.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Split the PM code out of arch/arm/plat-s3c24xx/irq.c to
remove some of the #ifdefs being used. Also fix a couple
of places where the absecnce of a function was redefined
to the same thing.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix warnings from struct resource being bigger than unsigned long by
forcing the type. We are only a 32bit platform so no physical memory
addresses will be too big to fit in this.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Split the optional memory check code out of the pm.c file
as it is quite a big #ifdef block and as-such can be moved
out and simply compiled when the configuration is set.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Start moving the PM code by moving all the common support functions
to a common location in arch/arm/plat-s3c. With the move we rename
the functions from s3cxxx_ to s3c_ to fit the new location.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the <plat/pm.h> header to plat-s3c as preparation
for moving parts of the s3c24xx pm support which are
common into the plat-s3c support.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Includes missed irqs.h in devices.c and mx1ads.c.
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add two more bitfields for the PSP register. As they seem to exist
for PXA3xx only, define them conditionally.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A bit in PXA's SSCR0 register was erroneously named ADC but its name is
in fact ACS (audio clock select).
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add the initial code to support the S3C64XX I2S hardware using the
s3c-i2s-v2 core code.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix build warnings due to struct i2c_board_info in <mach/platform.h>
Patch "5311/1: add core support for built in i2c bus" is causing 11 of
39 the build warnings with Kautobuild for ep93xx_defconfig on kernel
2.6.29-rc5-git4. This patch fixes it.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Cc: Andrew Victor <avictor.za@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
