The specialix module is missing the char-major-75-* alias that would
cause it to be auto-loaded when a device of that type is opened. This
patch adds the alias.
Signed-off-by: Scott James Remnant <scott@canonical.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The cyclades module is missing the char-major-19-* alias that would
cause it to be auto-loaded when a device of that type is opened. This
patch adds the alias.
Signed-off-by: Scott James Remnant <scott@canonical.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The applicom module is missing the char-major-10-157 alias that would
cause it to be auto-loaded when a device of that type is opened. This
patch adds the alias.
Signed-off-by: Scott James Remnant <scott@canonical.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes this compile issue:
drivers/serial/bfin_5xx.c: In function bfin_serial_rx_chars:
drivers/serial/bfin_5xx.c:178: error: struct uart_info has no member named tty
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This implements basic support for all 843x RS232 devices, but does not
add DMA support. This means that sustained data transfers at high baud
rates may not be possible on multiple ports simultaneously.
Signed-off-by: Shawn Bohrer <shawn.bohrer@ni.com>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add new Wacom device IDs to the 8250_pnp serial driver, to support
autoconfig on some newer tablet PCs. Also add a comment to clarify that
the FUJ02E6 device is a custom protocol, not a Wacom tablet.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@etchedpixels.co.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add another serial Wacom tablet with pnp_id: WACF009.
Signed-off-by: Danny Kukawka <dkukawka@suse.de>
Signed-off-by: Alan Cox <alan@etchedpixels.co.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There's no point in this, since the user can use the BUILTIN_FIRMWARE
option to include arbitrary firmware files directly in the kernel image.
Thanks to David Woodhouse for help.
Signed-off-by: Jaswinder Singh <jaswinder@infradead.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix this build error:
drivers/pci/intr_remapping.c: In function 'ir_parse_ioapic_scope':
drivers/pci/intr_remapping.c:617: error: invalid use of undefined type
'struct acpi_dmar_hardware_unit'
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
It's possible for a device in the drhd->devices[] array to be NULL if
it wasn't found at boot time, which means we have to check for that
case.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-backlight:
backlight: Adds HP Jornada 700 series backlight driver
backlight: Add HP Jornada 700 series LCD driver
backlight: fix pwm_bl.c when multiple PWM backlights exist
backlight: mbp_nvidia_bl - Add a debug switch
backlight: Add support for MacBook 5, MacBook Air 2, and MacBook Pro 5
If a logical hot unplug (remove) is performed on a physical PCI slot's
parent bridge, and then pci_slot is unloaded, we will encounter an oops:
[<ffffffff803a788a>] kobject_release+0x9a/0x290
[<ffffffff803a77f0>] ? kobject_release+0x0/0x290
[<ffffffff803a8ce7>] kref_put+0x37/0x80
[<ffffffff803a76f7>] kobject_put+0x27/0x60
[<ffffffff803bebcc>] ? pci_destroy_slot+0x3c/0xc0
[<ffffffff803bebd5>] pci_destroy_slot+0x45/0xc0
[<ffffffffa000f05c>] acpi_pci_slot_remove+0x5c/0x91 [pci_slot]
[<ffffffff8040064b>] acpi_pci_unregister_driver+0x4b/0x62
[<ffffffffa000f5c8>] acpi_pci_slot_exit+0x10/0x12 [pci_slot]
[<ffffffff80276ce1>] sys_delete_module+0x161/0x250
We need to grab a reference to the parent PCI bus, which will pin
the bus and prevent it from being released until pci_slot is unloaded.
Cc: lenb@kernel.org
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Tested-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Reported-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If a logical hot unplug (remove) is performed on a bridge claimed
by acpiphp and then acpiphp is unloaded, we will encounter an oops.
This is because acpiphp will access the bridge's subordinate bus,
which was released by the user's prior hot unplug.
The solution is to grab a reference on the subordinate PCI bus.
This will prevent the bus from release until acpiphp is unloaded.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Tested-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Reported-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
There is no reason to prevent removal of root bus devices. A subsequent
rescan will find them just fine.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch fixes breakage of of enable_cnt in quirk_resource_alignment.
Currently, quirk_resource_alignment calls pci_disable_device.
pci_disable_device decrements enable_cnt, so that enable_cnt becomes -1.
The patch disables memory decoding, writing command register directly.
So enable_cnt is not broken.
Signed-off-by: Yuji Shimada <shimada-yxb@necst.nec.co.jp>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
pci_rescan_bus was annotated as __devinit, which is wrong,
because it will never be part of device initialization.
Howevever, we can't simply drop the annotation, because then we
get section warnings about calling pci_scan_child_bus (which is
correctly marked as __devinit).
pci_rescan_bus will only get built when CONFIG_HOTPLUG is set,
meaning that __devinit is a nop, so we know that pci_scan_child_bus
has not been freed.
Annotate as __ref to silence modpost.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Fix PCI iov kernel-doc warning:
Warning(drivers/pci/iov.c:638): No description found for parameter 'nr_virtfn'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch sets up disabled bridges even if buses have already been
added.
pci_assign_unassigned_resources is called after buses are added.
pci_assign_unassigned_resources calls pci_bus_assign_resources.
pci_bus_assign_resources calls pci_setup_bridge to configure BARs of
bridges.
Currently pci_setup_bridge returns immediately if the bus have already
been added. So pci_assign_unassigned_resources can't configure BARs of
bridges that were added in a disabled state; this patch fixes the issue.
On logical hot-add, we need to prevent the kernel from re-initializing
bridges that have already been initialized. To achieve this,
pci_setup_bridge returns immediately if the bridge have already been
enabled.
We don't need to check whether the specified bus is a root bus or not.
pci_setup_bridge is not called on a root bus, because a root bus does
not have a bridge.
The patch adds a new helper function, pci_is_enabled. I made the
function name similar to pci_is_managed. The codes which use
enable_cnt directly are changed to use pci_is_enabled.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Yuji Shimada <shimada-yxb@necst.nec.co.jp>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If BIOS doesn't allocate resources for the SR-IOV BARs, zero the Flash
BAR and program the SR-IOV BARs to use the old Flash Memory Space.
Please refer to Intel 82576 Gigabit Ethernet Controller Datasheet
section 7.9.2.14.2 for details.
http://download.intel.com/design/network/datashts/82576_Datasheet.pdf
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
It's required for all modules loaded in the previous runtime
session because not initilized duing the kernel start-up.
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When multiple PWMs are used as backlights, the current code uses
pdev->name as the backlight name when registering, which will be
conflicting, use dev_name() instead.
Signed-off-by: Peter Edwards <sweetlilmre@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
This patch adds a debug switch to enable (little) diagnostic
output, to help to trace down the remaining problems.
Signed-off-by: Mario Schwalbe <schwalbe@inf.tu-dresden.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
This patch adds support for the new Apple models incorporating an Nvidia
chipset. Apple still uses the same protocol as on older models, but the
registers moved to a different address. To do this, two sets of functions
are added for the Intel/Nvidia chipset models and passed by the DMI_MATCH
function.
The initial code has been contributed by Hu Gang <hugang@soulinfo.com>.
The driver is known to work on MacBook Pro 3, MacBook Pro 4 and MacBook
Pro 5.
Its known to work with limitations on MacBook 5 / MacBook Air 2. Changing
brightness within X doesn't work, if using Nvidia's proprietary graphics
driver with no known fix at present. Changing brightness on a text console
or using the open-source driver does work.
MacBook Pro 5 has a known bug where the initial brightness after bootup is
the last recently used brightness (in Mac OSX), while the firmware reports
maximum. Impossible to fix.
[akpm@linux-foundation.org: build fix]
[rpurdie@linux.intel.com: Rebased the patch against latest git]
Signed-off-by: Mario Schwalbe <schwalbe@inf.tu-dresden.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
LP5521 is a three channel led driver with support
for hardware accelerated patterns (currently used
via lp5521-only sysfs interface).
Currently, it's used on n810 device.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Sometimes it's awkward to make sure that the array in the
platform_data handed to the leds-gpio driver has only valid
data ... some leds may not be always available, and coping
with that currently requires patching or rebuilding the array.
This patch fixes that by making it be OK to pass an invalid
GPIO (such as "-EINVAL") ... such table entries are skipped.
[rpurdie@linux.intel.com: adjusted to apply against other led tree changes]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Tested-by: Diego Dompe <diego.dompe@ridgerun.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
This fixes the expression in the driver to do the correct thing,
not that I think anyone would send SND_* without EV_SND.
Thanks to Roel Kluin <roel.kluin@gmail.com> for noticing.
Signed-off-by: Riku Voipio <riku.voipio@iki.fi>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
A pointer to h1940leds_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
This goto is unnecessary.
Signed-off-by: Zhenwen Xu <helight.xu@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
ROHM BD2802GU is a RGB LED controller attached to i2c bus and specifically
engineered for decoration purposes. This RGB controller incorporates
lighting patterns and illuminates.
This driver is designed to minimize power consumption, so when there is no
emitting LED, it enters to reset state. And because the BD2802GU has lots
of features that can't be covered by the current LED framework, it
provides Advanced Configuration Function(ADF) mode, so that user
applications can set registers of BD2802GU directly.
Here are basic usage examples :
; to turn on LED (not blink)
$ echo 1 > /sys/class/leds/led1_R/brightness
; to blink LED
$ echo timer > /sys/class/leds/led1_R/trigger
$ echo 1 > /sys/class/leds/led1_R/delay_on
$ echo 1 > /sys/class/leds/led1_R/delay_off
; to turn off LED
$ echo 0 > /sys/class/leds/led1_R/brightness
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Kim Kyuwon <chammoru@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
The leds-clevo-mail driver is in the mainline kernel since 2.6.25 and works
without severe problems. Make this driver available for a larger audience.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
The gpio led trigger will allow leds to be triggered by
gpio events.
When we give the led a gpio number, the trigger will
request_irq() on that so we don't have to keep polling
for gpio state.
It's useful for usecases as n810's keypad leds that could
be triggered by the gpio event generated when user slides
up to show the keypad.
We also provide means for userland to tell us what is the
desired brightness for that special led when it goes on
so userland could use information from ambient light sensors
and not set led brightness too high if it's not necessary.
Signed-off-by: Felipe Balbi <me@felipebalbi.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Mikrotik built six LEDs into the Routerboard 532, from which one is
destined for custom use, the so called "User LED". This patch adds a
driver for it, based on the LEDs class.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Add an option to preserve LED state when suspending/resuming to the LED
gpio driver. Based on a suggestion from Robert Jarzmik.
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Add a simple driver for pwm driver LEDs. pwm_id and period can be defined
in board file. It is developed for pxa, however it is probably generic
enough to be used on other platforms with pwm.
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
You can't have multiple module_init()/module_exit calls so resort to messy
ifdefs potentially pending some code refactoring.
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
