With a postfix decrement t reaches -1 rather than 0, so the fall-back will
not occur.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: mano@roarinelk.homelinux.net
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some of the rate selection logic in s3c64xx_setrate_clksrc uses what
appears to be parent clock selection logic. This patch corrects it.
I also added a check for overly large dividers to prevent them from
changing unrelated clocks.
Signed-off-by: Werner Almesberger <werner@openmoko.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix the following sparse warnings in s3c6400-clock.c:
39:12: warning: symbol 'clk_ext_xtal_mux' was not declared. Should it be static?
66:12: warning: symbol 'clk_fout_apll' was not declared. Should it be static?
81:19: warning: symbol 'clk_mout_apll' was not declared. Should it be static?
91:12: warning: symbol 'clk_fout_epll' was not declared. Should it be static?
106:19: warning: symbol 'clk_mout_epll' was not declared. Should it be static?
126:19: warning: symbol 'clk_mout_mpll' was not declared. Should it be static?
148:12: warning: symbol 'clk_dout_mpll' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
With the recent entry.S refactoring, the SH-X3 path had a mov.l for a
register to register copy, resulting in:
AS arch/sh/kernel/cpu/sh4/../sh3/entry.o
arch/sh/kernel/cpu/sh4/../sh3/entry.S: Assembler messages:
arch/sh/kernel/cpu/sh4/../sh3/entry.S:366: Error: invalid operands for opcode
make[3]: *** [arch/sh/kernel/cpu/sh4/../sh3/entry.o] Error 1
Switch it over to a mov to fix it up.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update intc tables and platform data to use one linux irq
per maskable interrupt source instead of keeping the one-to-one
mapping between vectors and linux irqs.
This fixes potential irq masking issues for sh7785 hardware
blocks such as SCIF/DMAC/PCIC5/MMCIF/GDTA/FLCTL/GPIO
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Tested-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update intc tables and platform data to use one linux irq
per maskable interrupt source instead of keeping the one-to-one
mapping between vectors and linux irqs.
This fixes potential irq masking issues for sh7780 hardware
blocks such as SCIF/RTC/DMAC/PCIC5/MMCIF/FLCTL/GPIO
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update intc tables and platform data to use one linux irq
per maskable interrupt source instead of keeping the one-to-one
mapping between vectors and linux irqs.
This fixes potential irq masking issues for sh775x hardware
blocks such as SCI/SCIF/RTC/DMAC/TMU2/REF.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Instead of keeping the single vector -> single linux irq mapping
we extend the intc code to support merging of vectors to a single
linux irq. This helps processors such as sh7750, sh7780 and sh7785
which have more vectors than masking ability. With this patch in
place we can modify the intc tables to use one irq per maskable
irq source. Please note the following:
- If multiple vectors share the same enum then only the
first vector will be available as a linux irq.
- Drivers may need to be rewritten to get pending irq
source from the hardware block instead of irq number.
This patch together with the sh7785 specific intc tables solves
DMA controller irq issues related to buggy interrupt masking.
Reported-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix iounmap() of pass-through P4 addresses. Without this patch
iounmap() on the sh7780 rtc area results in a warning message.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The SH-3 does not support 'pref'-based prefetching, only SH-2A and SH-4A
parts do. Remove SH-3 from the list.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Prefetch early exception data. There is unused space in our
exception handler cache line anyway, so this is almost free.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Remove EXPEVT vector from the stack, lookup_exception_vector()
for sh3/sh4/sh4a is already using k2 to get the vector.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch reworks the sh3/sh4/sh4a register restore code in
the following ways:
- break out restore_regs() from restore_all()
- the register saving order is unchanged
- use restore_regs() in sh_bios_handler and restore_all
- document the function
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch reworks the sh3/sh4/sh4a register saving code in
the following ways:
- break out prepare_stack_save_dsp() from handle_exception()
- break out save_regs() from handle_exception()
- the register saving order is unchanged
- align new functions to fit in cache lines
- separate exception code from interrupt code
- keep main code flow in a single cache line per exception vector
- use bsr/rts for regular functions (save pr first)
- keep data in one shared cache line (exception_data)
- document the functions
- tie in the hp6xx code
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This change depends on some v4l changes that have been pushed back to
2.6.30, so drop this and fall back on the old soc_camera code until then.
Reported-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Acked-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
m68knommu: add FEC platform support to ColdFire CPU's setup code
Move the per-CPU FEC driver setup code into the actual platform
setup code for each ColdFire CPU varient.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
To better match the ePAPR specification, device nodes which claim
"simple-bus" compatibility should be probed by default.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
On digsy MTC PSC4 and PSC5 should be configured as UART, not PSC3 and PSC4.
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The following options are enabled to support the digsy-mtc.
- LXT phy
- AT24 eeprom
- RTC (DS1337)
- MTD partitioning based on OF description
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The RTC and the two XOR engines are internal to the chip, and therefore
always available since they don't depend on a particular board layout.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
The clock list for the USB host bus clock was in the wrong order,
move clk_48m to position 0.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The USB OHCI host device expects the IRQ definition to be named
IRQ_USBH, so rename the S3C64XX IRQ header to match.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
arch_initcall() runs after the machine init function which means that
any configuration of GPIO pins must currently be done later on, for
example in callbacks from drivers. Move the initialisation earlier in
order to allow machines to configure GPIOs directly in their init
functions rather than having to have a callback invoked later on.
Some other ARM platforms use this method. Other solutions for this
include providing a special interface for setting up GPIOs en masse,
adding callbacks to do the GPIO configuration from devices and doing
the GPIO configuration implicitly.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
It's an initcall and does not need to be exported.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The WM8580 driver registers itself as "wm8580" rather than "WM8580".
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The PCI 2.x cells used on some 44x SoCs only let us configure the decode
for the low 32-bit of the incoming PLB addresses. The top 4 bits (this
is a 36-bit bus) are hard wired to different values depending on the
specific SoC in use. Our code used to work "by accident" until I added
support for the ISA memory holes and while at it added more validity
checking of the addresses.
This patch should bring it back to working condition. It still relies
on the device-tree being correct but that's somewhat a pre-requisite
for anything to work anyway.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
fix this warning:
arch/x86/kernel/cpu/intel_cacheinfo.c:139: warning: ‘k8_nb_id’ defined but not used
arch/x86/kernel/cpu/intel_cacheinfo.c:527: warning: ‘free_cache_attributes’ defined but not used
arch/x86/kernel/cpu/intel_cacheinfo.c:538: warning: ‘detect_cache_attributes’ defined but not used
Unused variables in the !CONFIG_SYSCTL case.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This is a framebuffer driver for i.MX31 SoCs. It only supports synchronous
displays, vertical panning supported, no overlay support.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This reverts commit 86528da229.
This version of the patch was tab-to-space corrupted before
application.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
If the TSC is constant and non-stop, also set it reliable.
(We will turn this off in DMI quirks for multi-chassis systems)
The performance number on a 16-way Nehalem system running
32 tasks that context-switch between each other is significant:
sched_clock_stable=0 sched_clock_stable=1
.................... ....................
22.456925 million/sec 24.306972 million/sec [+8.2%]
lmbench's "lat_ctx -s 0 2" goes from 0.63 microseconds to
0.59 microseconds - a 6.7% increase in context-switching
performance.
Perfstat of 1 million pipe context switches between two tasks:
Performance counter stats for './pipe-test-1m':
[before] [after]
............ ............
37621.421089 36436.848378 task clock ticks (msecs)
0 0 CPU migrations (events)
2000274 2000189 context switches (events)
194 193 pagefaults (events)
8433799643 8171016416 CPU cycles (events) -3.21%
8370133368 8180999694 instructions (events) -2.31%
4158565 3895941 cache references (events) -6.74%
44312 46264 cache misses (events)
2349.287976 2279.362465 wall-time (msecs) -3.06%
The speedup comes straight from the reduction in the instruction
count. sched_clock_cpu() got simpler and the whole workload thus
executes faster.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Now that the obvious bugs have been worked out, specifically
the iwlagn issue, and the write buffer errata, DMAR should be safe
to turn back on by default. (We've had it on since those patches were
first written a few weeks ago, without any noticeable bug reports
(most have been due to the dma-api debug patchset.))
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
arch/x86/kernel/apic/es7000_32.c:702: error: 'es7000_acpi_madt_oem_check_cluster' undeclared here (not in a function)
Provide a es7000_acpi_madt_oem_check_cluster() definition in the !ACPI
case too.
Cc: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: build fix
init_deasserted is only available on SMP. Make the secondary-wakeup
function conditional on SMP.
Also clean up the file some.
Cc: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
- rename apic->wakeup_cpu to apic->wakeup_secondary_cpu, to
make it apparent that this is an SMP-only method
- handle NULL ->wakeup_secondary_cpus to mean the default INIT
wakeup sequence - this allows simplification of the APIC
driver templates.
Cc: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: build fix
wakeup_secondary_cpu_via_init(), the default platform method for
booting a secondary CPU, is always used on UP due to probe_32.c,
if CONFIG_X86_LOCAL_APIC is enabled but SMP is off.
So provide a UP wrapper inline as well.
Cc: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
With the mandatory algorithm testing at registration, we have
now created a deadlock with algorithms requiring fallbacks.
This can happen if the module containing the algorithm requiring
fallback is loaded first, without the fallback module being loaded
first. The system will then try to test the new algorithm, find
that it needs to load a fallback, and then try to load that.
As both algorithms share the same module alias, it can attempt
to load the original algorithm again and block indefinitely.
As algorithms requiring fallbacks are a special case, we can fix
this by giving them a different module alias than the rest. Then
it's just a matter of using the right aliases according to what
algorithms we're trying to find.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Impact: cleanup
that is only needed when CONFIG_X86_VSMP is defined with 64bit
also remove dead code about PCI, because CONFIG_X86_VSMP depends on PCI
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
x86_quirks->update_apic() calling looks crazy. so try to remove it:
1. every apic take wakeup_cpu member directly
2. separate es7000_apic to es7000_apic_cluster
3. use uv_wakeup_cpu directly
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
