Linux guests on Haswell (and also SandyBridge and Broadwell, at least)
would crash if you decided to run a host command that uses PEBS, like
perf record -e 'cpu/mem-stores/pp' -a
This happens because KVM is using VMX MSR switching to disable PEBS, but
SDM [2015-12] 18.4.4.4 Re-configuring PEBS Facilities explains why it
isn't safe:
When software needs to reconfigure PEBS facilities, it should allow a
quiescent period between stopping the prior event counting and setting
up a new PEBS event. The quiescent period is to allow any latent
residual PEBS records to complete its capture at their previously
specified buffer address (provided by IA32_DS_AREA).
There might not be a quiescent period after the MSR switch, so a CPU
ends up using host's MSR_IA32_DS_AREA to access an area in guest's
memory. (Or MSR switching is just buggy on some models.)
The guest can learn something about the host this way:
If the guest doesn't map address pointed by MSR_IA32_DS_AREA, it results
in #PF where we leak host's MSR_IA32_DS_AREA through CR2.
After that, a malicious guest can map and configure memory where
MSR_IA32_DS_AREA is pointing and can therefore get an output from
host's tracing.
This is not a critical leak as the host must initiate with PEBS tracing
and I have not been able to get a record from more than one instruction
before vmentry in vmx_vcpu_run() (that place has most registers already
overwritten with guest's).
We could disable PEBS just few instructions before vmentry, but
disabling it earlier shouldn't affect host tracing too much.
We also don't need to switch MSR_IA32_PEBS_ENABLE on VMENTRY, but that
optimization isn't worth its code, IMO.
(If you are implementing PEBS for guests, be sure to handle the case
where both host and guest enable PEBS, because this patch doesn't.)
Fixes: 26a4f3c08d ("perf/x86: disable PEBS on a guest entry.")
Cc: <stable@vger.kernel.org>
Reported-by: Jiří Olša <jolsa@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Branch-free code is fun and everybody knows how much Avi loves it,
but last_pte_bitmap takes it a bit to the extreme. Since the code
is simply doing a range check, like
(level == 1 ||
((gpte & PT_PAGE_SIZE_MASK) && level < N)
we can make it branch-free without storing the entire truth table;
it is enough to cache N.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
mmu_sync_children can only process up to 16 pages at a time. Check
if we need to reschedule, and do not bother zapping the pages until
that happens.
Reviewed-by: Takuya Yoshikawa <yoshikawa_takuya_b1@lab.ntt.co.jp>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
kvm_mmu_get_page is the only caller of kvm_sync_page_transient
and kvm_sync_pages. Moving the handling of the invalid_list there
removes the need for the underdocumented kvm_sync_page_transient
function.
Reviewed-by: Takuya Yoshikawa <yoshikawa_takuya_b1@lab.ntt.co.jp>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Return true if the page was synced (and the TLB must be flushed)
and false if the page was zapped.
Reviewed-by: Takuya Yoshikawa <yoshikawa_takuya_b1@lab.ntt.co.jp>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Calling kvm_unlink_unsync_page in the middle of __kvm_sync_page makes
things unnecessarily tricky. If kvm_mmu_prepare_zap_page is called,
it will call kvm_unlink_unsync_page too. So kvm_unlink_unsync_page can
be called just as well at the beginning or the end of __kvm_sync_page...
which means that we might do it in kvm_sync_page too and remove the
parameter.
kvm_sync_page ends up being the same code that kvm_sync_pages used
to have before the previous patch.
Reviewed-by: Takuya Yoshikawa <yoshikawa_takuya_b1@lab.ntt.co.jp>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If the last argument is true, kvm_unlink_unsync_page is called anyway in
__kvm_sync_page (either by kvm_mmu_prepare_zap_page or by __kvm_sync_page
itself). Therefore, kvm_sync_pages can just call kvm_sync_page, instead
of going through kvm_unlink_unsync_page+__kvm_sync_page.
Reviewed-by: Takuya Yoshikawa <yoshikawa_takuya_b1@lab.ntt.co.jp>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
By doing this, kvm_sync_pages can use __kvm_sync_page instead of
reinventing it. Because of kvm_mmu_flush_or_zap, the code does not
end up being more complex than before, and more cleanups to kvm_sync_pages
will come in the next patches.
Reviewed-by: Takuya Yoshikawa <yoshikawa_takuya_b1@lab.ntt.co.jp>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This is a generalization of mmu_pte_write_flush_tlb, that also
takes care of calling kvm_mmu_commit_zap_page. The next
patches will introduce more uses.
Reviewed-by: Takuya Yoshikawa <yoshikawa_takuya_b1@lab.ntt.co.jp>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The callers of steal_account_process_tick() expect it to return
whether a jiffy should be considered stolen or not.
Currently the return value of steal_account_process_tick() is in
units of cputime, which vary between either jiffies or nsecs
depending on CONFIG_VIRT_CPU_ACCOUNTING_GEN.
If cputime has nsecs granularity and there is a tiny amount of
stolen time (a few nsecs, say) then we will consider the entire
tick stolen and will not account the tick on user/system/idle,
causing /proc/stats to show invalid data.
The fix is to change steal_account_process_tick() to accumulate
the stolen time and only account it once it's worth a jiffy.
(Thanks to Frederic Weisbecker for suggestions to fix a bug in my
first version of the patch.)
Signed-off-by: Chris Friesen <chris.friesen@windriver.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@vger.kernel.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/56DBBDB8.40305@mail.usask.ca
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The dl_new field of struct sched_dl_entity is currently used to
identify new deadline tasks, so that their deadline and runtime
can be properly initialised.
However, these tasks can be easily identified by checking if
their deadline is smaller than the current time when they switch
to SCHED_DEADLINE. So, dl_new can be removed by introducing this
check in switched_to_dl(); this allows to simplify the
SCHED_DEADLINE code.
Signed-off-by: Luca Abeni <luca.abeni@unitn.it>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Juri Lelli <juri.lelli@arm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1457350024-7825-2-git-send-email-luca.abeni@unitn.it
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Jiri reported some time ago that some entries in the PEBS data source table
in perf do not agree with the SDM. We investigated and the bits
changed for Sandy Bridge, but the SDM was not updated.
perf already implements the bits correctly for Sandy Bridge
and later. This patch patches it up for Nehalem and Westmere.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <stable@vger.kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: jolsa@kernel.org
Link: http://lkml.kernel.org/r/1456871124-15985-1-git-send-email-andi@firstfloor.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch adds a Broadwell specific PEBS event constraint table.
Broadwell has a fix for the HT corruption bug erratum HSD29 on
Haswell. Therefore, there is no need to mark events 0xd0, 0xd1, 0xd2,
0xd3 has requiring the exclusive mode across both sibling HT threads.
This holds true for regular counting and sampling (see core.c) and
PEBS (ds.c) which we fix in this patch.
In doing so, we relax evnt scheduling for these events, they can now
be programmed on any 4 counters without impacting what is measured on
the sibling thread.
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: acme@redhat.com
Cc: adrian.hunter@intel.com
Cc: jolsa@redhat.com
Cc: kan.liang@intel.com
Cc: namhyung@kernel.org
Link: http://lkml.kernel.org/r/1457034642-21837-4-git-send-email-eranian@google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch fixes an issue with the GLOBAL_OVERFLOW_STATUS bits on
Haswell, Broadwell and Skylake processors when using PEBS.
The SDM stipulates that when the PEBS iterrupt threshold is crossed,
an interrupt is posted and the kernel is interrupted. The kernel will
find GLOBAL_OVF_SATUS bit 62 set indicating there are PEBS records to
drain. But the bits corresponding to the actual counters should NOT be
set. The kernel follows the SDM and assumes that all PEBS events are
processed in the drain_pebs() callback. The kernel then checks for
remaining overflows on any other (non-PEBS) events and processes these
in the for_each_bit_set(&status) loop.
As it turns out, under certain conditions on HSW and later processors,
on PEBS buffer interrupt, bit 62 is set but the counter bits may be
set as well. In that case, the kernel drains PEBS and generates
SAMPLES with the EXACT tag, then it processes the counter bits, and
generates normal (non-EXACT) SAMPLES.
I ran into this problem by trying to understand why on HSW sampling on
a PEBS event was sometimes returning SAMPLES without the EXACT tag.
This should not happen on user level code because HSW has the
eventing_ip which always point to the instruction that caused the
event.
The workaround in this patch simply ensures that the bits for the
counters used for PEBS events are cleared after the PEBS buffer has
been drained. With this fix 100% of the PEBS samples on my user code
report the EXACT tag.
Before:
$ perf record -e cpu/event=0xd0,umask=0x81/upp ./multichase
$ perf report -D | fgrep SAMPLES
PERF_RECORD_SAMPLE(IP, 0x2): 11775/11775: 0x406de5 period: 73469 addr: 0 exact=Y
\--- EXACT tag is missing
After:
$ perf record -e cpu/event=0xd0,umask=0x81/upp ./multichase
$ perf report -D | fgrep SAMPLES
PERF_RECORD_SAMPLE(IP, 0x4002): 11775/11775: 0x406de5 period: 73469 addr: 0 exact=Y
\--- EXACT tag is set
The problem tends to appear more often when multiple PEBS events are used.
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <stable@vger.kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: adrian.hunter@intel.com
Cc: kan.liang@intel.com
Cc: namhyung@kernel.org
Link: http://lkml.kernel.org/r/1457034642-21837-3-git-send-email-eranian@google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch adds a definition for GLOBAL_OVFL_STATUS bit 55
which is used with the Processor Trace (PT) feature.
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <stable@vger.kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: adrian.hunter@intel.com
Cc: kan.liang@intel.com
Cc: namhyung@kernel.org
Link: http://lkml.kernel.org/r/1457034642-21837-2-git-send-email-eranian@google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch tries to fix a PEBS warning found in my stress test. The
following perf command can easily trigger the pebs warning or spurious
NMI error on Skylake/Broadwell/Haswell platforms:
sudo perf record -e 'cpu/umask=0x04,event=0xc4/pp,cycles,branches,ref-cycles,cache-misses,cache-references' --call-graph fp -b -c1000 -a
Also the NMI watchdog must be enabled.
For this case, the events number is larger than counter number. So
perf has to do multiplexing.
In perf_mux_hrtimer_handler, it does perf_pmu_disable(), schedule out
old events, rotate_ctx, schedule in new events and finally
perf_pmu_enable().
If the old events include precise event, the MSR_IA32_PEBS_ENABLE
should be cleared when perf_pmu_disable(). The MSR_IA32_PEBS_ENABLE
should keep 0 until the perf_pmu_enable() is called and the new event is
precise event.
However, there is a corner case which could restore PEBS_ENABLE to
stale value during the above period. In perf_pmu_disable(), GLOBAL_CTRL
will be set to 0 to stop overflow and followed PMI. But there may be
pending PMI from an earlier overflow, which cannot be stopped. So even
GLOBAL_CTRL is cleared, the kernel still be possible to get PMI. At
the end of the PMI handler, __intel_pmu_enable_all() will be called,
which will restore the stale values if old events haven't scheduled
out.
Once the stale pebs value is set, it's impossible to be corrected if
the new events are non-precise. Because the pebs_enabled will be set
to 0. x86_pmu.enable_all() will ignore the MSR_IA32_PEBS_ENABLE
setting. As a result, the following NMI with stale PEBS_ENABLE
trigger pebs warning.
The pending PMI after enabled=0 will become harmless if the NMI handler
does not change the state. This patch checks cpuc->enabled in pmi and
only restore the state when PMU is active.
Here is the dump:
Call Trace:
<NMI> [<ffffffff813c3a2e>] dump_stack+0x63/0x85
[<ffffffff810a46f2>] warn_slowpath_common+0x82/0xc0
[<ffffffff810a483a>] warn_slowpath_null+0x1a/0x20
[<ffffffff8100fe2e>] intel_pmu_drain_pebs_nhm+0x2be/0x320
[<ffffffff8100caa9>] intel_pmu_handle_irq+0x279/0x460
[<ffffffff810639b6>] ? native_write_msr_safe+0x6/0x40
[<ffffffff811f290d>] ? vunmap_page_range+0x20d/0x330
[<ffffffff811f2f11>] ? unmap_kernel_range_noflush+0x11/0x20
[<ffffffff8148379f>] ? ghes_copy_tofrom_phys+0x10f/0x2a0
[<ffffffff814839c8>] ? ghes_read_estatus+0x98/0x170
[<ffffffff81005a7d>] perf_event_nmi_handler+0x2d/0x50
[<ffffffff810310b9>] nmi_handle+0x69/0x120
[<ffffffff810316f6>] default_do_nmi+0xe6/0x100
[<ffffffff810317f2>] do_nmi+0xe2/0x130
[<ffffffff817aea71>] end_repeat_nmi+0x1a/0x1e
[<ffffffff810639b6>] ? native_write_msr_safe+0x6/0x40
[<ffffffff810639b6>] ? native_write_msr_safe+0x6/0x40
[<ffffffff810639b6>] ? native_write_msr_safe+0x6/0x40
<<EOE>> <IRQ> [<ffffffff81006df8>] ? x86_perf_event_set_period+0xd8/0x180
[<ffffffff81006eec>] x86_pmu_start+0x4c/0x100
[<ffffffff8100722d>] x86_pmu_enable+0x28d/0x300
[<ffffffff811994d7>] perf_pmu_enable.part.81+0x7/0x10
[<ffffffff8119cb70>] perf_mux_hrtimer_handler+0x200/0x280
[<ffffffff8119c970>] ? __perf_install_in_context+0xc0/0xc0
[<ffffffff8110f92d>] __hrtimer_run_queues+0xfd/0x280
[<ffffffff811100d8>] hrtimer_interrupt+0xa8/0x190
[<ffffffff81199080>] ? __perf_read_group_add.part.61+0x1a0/0x1a0
[<ffffffff81051bd8>] local_apic_timer_interrupt+0x38/0x60
[<ffffffff817af01d>] smp_apic_timer_interrupt+0x3d/0x50
[<ffffffff817ad15c>] apic_timer_interrupt+0x8c/0xa0
<EOI> [<ffffffff81199080>] ? __perf_read_group_add.part.61+0x1a0/0x1a0
[<ffffffff81123de5>] ? smp_call_function_single+0xd5/0x130
[<ffffffff81123ddb>] ? smp_call_function_single+0xcb/0x130
[<ffffffff81199080>] ? __perf_read_group_add.part.61+0x1a0/0x1a0
[<ffffffff8119765a>] event_function_call+0x10a/0x120
[<ffffffff8119c660>] ? ctx_resched+0x90/0x90
[<ffffffff811971e0>] ? cpu_clock_event_read+0x30/0x30
[<ffffffff811976d0>] ? _perf_event_disable+0x60/0x60
[<ffffffff8119772b>] _perf_event_enable+0x5b/0x70
[<ffffffff81197388>] perf_event_for_each_child+0x38/0xa0
[<ffffffff811976d0>] ? _perf_event_disable+0x60/0x60
[<ffffffff811a0ffd>] perf_ioctl+0x12d/0x3c0
[<ffffffff8134d855>] ? selinux_file_ioctl+0x95/0x1e0
[<ffffffff8124a3a1>] do_vfs_ioctl+0xa1/0x5a0
[<ffffffff81036d29>] ? sched_clock+0x9/0x10
[<ffffffff8124a919>] SyS_ioctl+0x79/0x90
[<ffffffff817ac4b2>] entry_SYSCALL_64_fastpath+0x1a/0xa4
---[ end trace aef202839fe9a71d ]---
Uhhuh. NMI received for unknown reason 2d on CPU 2.
Do you have a strange power saving mode enabled?
Signed-off-by: Kan Liang <kan.liang@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <stable@vger.kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: http://lkml.kernel.org/r/1457046448-6184-1-git-send-email-kan.liang@intel.com
[ Fixed various typos and other small details. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Using PAGE_SIZE buffers makes the WRMSR to PERF_GLOBAL_CTRL in
intel_pmu_enable_all() mysteriously hang on Core2. As a workaround, we
don't do this.
The hard lockup is easily triggered by running 'perf test attr'
repeatedly. Most of the time it gets stuck on sample session with
small periods.
# perf test attr -vv
14: struct perf_event_attr setup :
--- start ---
...
'PERF_TEST_ATTR=/tmp/tmpuEKz3B /usr/bin/perf record -o /tmp/tmpuEKz3B/perf.data -c 123 kill >/dev/null 2>&1' ret 1
Reported-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Cc: <stable@vger.kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kan Liang <kan.liang@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/20160301190352.GA8355@krava.redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The error path in perf_event_open() is such that asking for a sampling
event on a PMU that doesn't generate interrupts will end up in dropping
the perf_sched_count even though it hasn't been incremented for this
event yet.
Given a sufficient amount of these calls, we'll end up disabling
scheduler's jump label even though we'd still have active events in the
system, thereby facilitating the arrival of the infernal regions upon us.
I'm fixing this by moving account_event() inside perf_event_alloc().
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <stable@vger.kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: vince@deater.net
Link: http://lkml.kernel.org/r/1456917854-29427-1-git-send-email-alexander.shishkin@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In an attempt to aid in understanding of what the threshold_block
structure holds, provide comments to describe the members here. Also,
trim comments around threshold_restart_bank() and update copyright info.
No functional change is introduced.
Signed-off-by: Aravind Gopalakrishnan <Aravind.Gopalakrishnan@amd.com>
[ Shorten comments. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/1457021458-2522-6-git-send-email-Aravind.Gopalakrishnan@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Deferred errors indicate errors that hardware could not fix. But it
still does not cause any interruption to program flow. So it does not
generate any #MC and UC bit in MCx_STATUS is not set.
Correct comment.
Signed-off-by: Aravind Gopalakrishnan <Aravind.Gopalakrishnan@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/1457021458-2522-5-git-send-email-Aravind.Gopalakrishnan@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In upcoming processors, the BLKPTR field is no longer used to indicate
the MSR number of the additional register. Insted, it simply indicates
the prescence of additional MSRs.
Fix the logic here to gather MSR address from MSR_AMD64_SMCA_MCx_MISC()
for newer processors and fall back to existing logic for older
processors.
[ Drop nextaddr_out label; style cleanups. ]
Signed-off-by: Aravind Gopalakrishnan <Aravind.Gopalakrishnan@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/1457021458-2522-4-git-send-email-Aravind.Gopalakrishnan@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
For Scalable MCA enabled processors, errors are listed per IP block. And
since it is not required for an IP to map to a particular bank, we need
to use HWID and McaType values from the MCx_IPID register to figure out
which IP a given bank represents.
We also have a new bit (TCC) in the MCx_STATUS register to indicate Task
context is corrupt.
Add logic here to decode errors from all known IP blocks for Fam17h
Model 00-0fh and to print TCC errors.
[ Minor fixups. ]
Signed-off-by: Aravind Gopalakrishnan <Aravind.Gopalakrishnan@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/1457021458-2522-3-git-send-email-Aravind.Gopalakrishnan@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Those MSRs are used only by the MCE code so move them there.
Signed-off-by: Aravind Gopalakrishnan <Aravind.Gopalakrishnan@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/1456785179-14378-2-git-send-email-Aravind.Gopalakrishnan@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Newer GCC versions trigger the following warning:
kernel/time/timekeeping.c: In function ‘get_device_system_crosststamp’:
kernel/time/timekeeping.c:987:5: warning: ‘clock_was_set_seq’ may be used uninitialized in this function [-Wmaybe-uninitialized]
if (discontinuity) {
^
kernel/time/timekeeping.c:1045:15: note: ‘clock_was_set_seq’ was declared here
unsigned int clock_was_set_seq;
^
GCC clearly is unable to recognize that the 'do_interp' boolean tracks
the initialization status of 'clock_was_set_seq'.
The GCC version used was:
gcc version 5.3.1 20151207 (Red Hat 5.3.1-2) (GCC)
Work it around by initializing clock_was_set_seq to 0. Compilers that
are able to recognize the code flow will eliminate the unnecessary
initialization.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
we have to check bit 40 of the facility list before issuing LPP
and not bit 48. Otherwise a guest running on a system with
"The decimal-floating-point zoned-conversion facility" and without
the "The set-program-parameters facility" might crash on an lpp
instruction.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: stable@vger.kernel.org # v4.4+
Fixes: e22cf8ca6f ("s390/cpumf: rework program parameter setting to detect guest samples")
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Merge perf/core improvements and fixes from Arnaldo Carvalho de Melo:
User visible changes:
- Allow grouping multiple sort keys per 'perf report/top --hierarchy'
level (Namhyung Kim)
- Document 'perf stat --detailed' option (Borislav Petkov)
Infrastructure changes:
- jitdump prep work for supporting it with Intel PT (Adrian Hunter)
- Use 64-bit shifts with (TSC) time conversion (Adrian Hunter)
Fixes:
- Explicitly declare inc_group_count as a void function (Colin Ian King)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Now hpp formats are linked using perf_hpp_list_node when hierarchy is
enabled. Like in stdio, use this info to print entries with multiple
sort keys in a single hierarchy properly.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/1457361308-514-8-git-send-email-namhyung@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Now hpp formats are linked using perf_hpp_list_node when hierarchy is
enabled. Like in stdio, use this info to print entries with multiple
sort keys in a single hierarchy properly.
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/1457361308-514-7-git-send-email-namhyung@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Now hpp formats are linked using perf_hpp_list_node when hierarchy is
enabled. Use this info to print entries with multiple sort keys in a
single hierarchy properly.
For example, the below example shows using 4 sort keys with 2 levels.
$ perf report --hierarchy -s '{prev_pid,prev_comm},{next_pid,next_comm}' \
--percent-limit 1 -i perf.data.sched
...
# Overhead prev_pid+prev_comm / next_pid+next_comm
# ........... .......................................
#
22.36% 0 swapper/0
9.48% 17773 transmission-gt
5.25% 109 kworker/0:1H
1.53% 6524 Xephyr
21.39% 17773 transmission-gt
9.52% 0 swapper/0
9.04% 0 swapper/2
1.78% 0 swapper/3
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/1457361308-514-6-git-send-email-namhyung@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When multiple sort keys are used in a single hierarchy, it should indent
using number of hierarchy levels instead of number of sort keys.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/1457361308-514-5-git-send-email-namhyung@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This implements having multiple sort keys in a single hierarchy level.
Originally only single sort key is supported for each level, but now
using the group syntax with '{ }', it can set more than one sort key in
one level. Note that now it needs to quote in order to prevent shell
interpretation.
For example:
$ perf report --hierarchy -s '{comm,dso},sym'
...
# Overhead Command / Shared Object / Symbol
# .............. ..........................................
#
48.67% swapper [kernel.vmlinux]
34.42% [k] intel_idle
1.30% [k] __tick_nohz_idle_enter
1.03% [k] cpuidle_reflect
8.87% firefox libpthread-2.22.so
6.60% [.] __GI___libc_recvmsg
1.18% [.] pthread_cond_signal@@GLIBC_2.3.2
1.09% [.] 0x000000000000ff4b
6.11% Xorg libc-2.22.so
5.27% [.] __memcpy_sse2_unaligned
In the above example, the command name and the shared object name are
shown on the same line but the symbol name is on the different line.
Since the first two are grouped by '{}', they are in the same level.
Suggested-and-Tested=by: Arnaldo Carvalho de Melo <acme@kernel.org>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/1457361308-514-4-git-send-email-namhyung@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Now each hists has its own hpp lists in hierarchy. So instead of having
a pointer to a single perf_hpp_fmt in a hist entry, make it point the
hpp_list for its level. This will be used to support multiple sort keys
in a single hierarchy level.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/1457361308-514-3-git-send-email-namhyung@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The perf_hpp__setup_hists_formats() is to build hists-specific output
formats (and sort keys). Currently it's only used in order to build the
output format in a hierarchy with same sort keys, but it could be used
with different sort keys in non-hierarchy mode later.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/1457361308-514-2-git-send-email-namhyung@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
I'm surprised this remained undocumented since at least 2011. And it is
actually a very useful switch, as Steve and I came to realize recently.
Add the text from
2cba3ffb9a ("perf stat: Add -d -d and -d -d -d options to show more CPU events")
which added the incrementing aspect to -d.
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Davidlohr Bueso <dbueso@suse.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mel Gorman <mgorman@suse.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 2cba3ffb9a ("perf stat: Add -d -d and -d -d -d options to show more CPU events")
Link: http://lkml.kernel.org/r/1457347294-32546-1-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The level field is to distinguish levels in the hierarchy mode.
Currently each column (perf_hpp_fmt) has a different level.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/1457103582-28396-2-git-send-email-namhyung@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit b9511cd761 ("perf/x86: Fix time_shift in perf_event_mmap_page")
altered the time conversion algorithms documented in the perf_event.h
header file, to use 64-bit shifts. That was done to make the code more
future-proof (i.e. some time in the future a 32-bit shift could be
allowed). Reflect those changes in perf tools.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1457005856-6143-9-git-send-email-adrian.hunter@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Move clockid validation into jit_process() so it can later be made
conditional.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1457005856-6143-6-git-send-email-adrian.hunter@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In preparation for moving clockid validation into jit_process().
Previously a return value of zero meant the processing had been done and
non-zero meant either the processing was not done (i.e. not the jitdump
file mmap event) or an error occurred.
Change it so that zero means the processing was not done, one means the
processing was done and successful, and negative values are an error.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1457005856-6143-5-git-send-email-adrian.hunter@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Some of the stubs are identical so just have one function for them.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1457005856-6143-3-git-send-email-adrian.hunter@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Currently, when injecting build ids, if there is AUX data then 'perf
inject' hits all DSOs because it is not known which DSOs the trace data
would hit.
That needs to be done for JIT injection also, and in fact there is no
reason to distinguish what kind of injection is being done. That is,
any time there is AUX data and the HEADER_BUID_ID feature flag is set,
and the AUX data is not being processed, then hit all DSOs. This patch
does that.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1457005856-6143-2-git-send-email-adrian.hunter@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The return type is not defined, so it defaults to int, however, the
function is not returning anything, so this is clearly not correct. Make
it a void function.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: He Kuang <hekuang@huawei.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/1457008214-14393-1-git-send-email-colin.king@canonical.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
While I was testing irq's on the cubietruck I found a couple of
not working irq pins. Further diving into the problem it opened
up a mess called "manual".
This so called manual (A20 user manual v1.3 dated 2014-10-10) says:
Pin overview:
Page 237: EINT26 is on mux 5.
Page 288: EINT26 is on mux 6.
The manual is so contradicting that further tests had to be made
to see which of the 2 statements where correct.
This patch is based on actual outcome of these tests and not what
the manual says.
Test procedure used:
Connect a 1 pulse per second (GPS) line to the pin.
echo pin### > /sys/class/gpio/export
echo in > /sys/class/gpio/gpio###/direction
echo rising > /sys/class/gpio/gpio###/edge
Check /proc/interrupts if a irq was attached and if irq's where
received.
Hardware used:
Henry Paulissen: Cubietruck
Andere Przywara: BananaPi M1
Tested-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Henry Paulissen <henry@nitronetworks.nl>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
While I was testing irq's on the cubietruck I found a couple of
not working irq pins. Further diving into the problem it opened
up a mess called "manual".
This so called manual (A20 user manual v1.3 dated 2014-10-10) says:
Pin overview:
Page 233: EINT12 is on pin PC19 mux6.
Page 236: EINT12 is on pin PH12 mux6.
Now, it is a bit strange to have the same IRQ on 2 different pins,
but I guess this could still be possible hardware wise. But then:
Pin registers:
Page 253: EINT12 is *not* on pin PC19.
Page 281: EINT12 is on pin PH12.
The manual is so contradicting that further tests had to be made
to see which of the 2 statements where correct.
This patch is based on actual outcome of these tests and not what
the manual says.
Test procedure used:
Connect a 1 pulse per second (GPS) line to the pin.
echo pin### > /sys/class/gpio/export
echo in > /sys/class/gpio/gpio###/direction
echo rising > /sys/class/gpio/gpio###/edge
Check /proc/interrupts if a irq was attached and if irq's where
received.
Signed-off-by: Henry Paulissen <henry@nitronetworks.nl>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit bdb0066df9 ("mfd: syscon: Decouple syscon interface from platform
devices") added the possibility to register syscon devices without
associated platform device. This also removed regmap debugfs facilities,
which don't work without a device. This patch associates the syscon regmap
that handles the IOMUX controller's general purpose registers with the
pinctrl device so that the GPR registers appear in the regmap debugfs
directory again. For example, on i.MX6Q the GPR registers now can be
read from /sys/kernel/debug/regmap/20e0000.iomuxc-gpr/registers.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The DT bindings for pinctrl-bcm2835 allow both the function and pull
to contain either one entry or one per pin. However, an error in the
DT parsing can cause failures if the number of pulls differs from the
number of functions.
Cc: stable@vger.kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
