Use of tracers in local_irq_disable is causes abort loops when called
with irqs disabled using a temporary stack. Replace local_irq_disable
with raw_local_irq_disable instead to avoid tracers.
Signed-off-by: Sebastian Capella <sebastian.capella@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It is better to change Mic2-Vref to manual mode.
Manual control Mic2-Vref will solve pop noise issue.
It will improve pop noise for power on, power off, S3 and resume.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If "efm32,location" property is not provided, keeping what is already
configured in the hardware, so its either the reset default 0 or whatever
the bootloader did.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
BIT[0:2] of register 01h is REVID, so the mask for REVID should be 0x7.
Also updates the code to use CS42L52_CHIP_REV_MASK.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch enables the use of READ_STRIP software emulation in
target_complete_ok_work() code for I/O READs.
This is useful when the fabric does not support READ_STRIP hardware
offload, but would still like to interact with backend device
that have T10 PI enabled.
v2 changes:
- Move TARGET_PROT_DIN_STRIP check from target_check_read_strip()
into target_complete_ok_work() (Sagi)
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Split up __sbc_dif_verify_read() so that VERIFY READ emulation can
perform target-core specific READ_STRIP, seperate from the existing
FILEIO/RAMDISK backend emulation code.
Also add sbc_dif_read_strip() in order to determine number of sectors
using cmd->prot_length, and skip the extra sbc_dif_copy_prot().
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch enables WRITE_INSERT emulation in target_execute_cmd()
in order to locally generate DIF PI before submitting the WRITE
to the underlying backend device.
This is required for fabric drivers that currently don't support
DIF over-the-wire, in order to inact with backend devices that
have hardware (IBLOCK) or software (FILEIO + RAMDISK) support
for handling T10 PI.
v2 changes:
- Convert to sbc_dif_generate() usage (Sagi)
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds WRITE_INSERT emulation within target-core
using TYPE1 / TYPE3 PI modes in sbc_dif_generate() code.
This is useful in order for existing legacy fabrics that do not
support protection offloads to interact with backend devices that
currently have T10 PI enabled.
v2 changes:
- Rename to sbc_dif_generate() (Sagi)
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Only expose the PI protection type bits in READ_CAPACITY_16
if the session + fabric support DIX PASS operations.
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Only expose the control modepage bit for Application Tag Owner (ATO)
if the session + fabric support DIX PASS operations.
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Only expose standard INQUIRY PROTECT=1 and EVPD=0x86 TYPE1/TYPE3
PI control bits if the session + fabric support DIX PASS operations.
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In order to support local WRITE_INSERT + READ_STRIP operations for
non PI enabled fabrics, the fabric driver needs to be able signal
what protection offload operations are supported.
This is done at session initialization time so the modes can be
signaled by individual se_wwn + se_portal_group endpoints, as well
as optionally across different transports on the same endpoint.
For iser-target, set TARGET_PROT_ALL if the underlying ib_device
has already signaled PI offload support, and allow this to be
exposed via a new iscsit_transport->iscsit_get_sup_prot_ops()
callback.
For loopback, set TARGET_PROT_ALL to signal SCSI initiator mode
operation.
For all other drivers, set TARGET_PROT_NORMAL to disable fabric
level PI.
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a double free bug during IBLOCK backend shutdown
where bioset_integrity_free() was incorrectly called ahead of
bioset_free(), who is already making the same call directly.
This bug was introduced with commit ecebbf6cc, and will end up
triggering a general protection fault in iblock_free_device()
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Cc: <stable@vger.kernel.org> #3.14+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
When compiled with CONFIG_DEBUG_SG set, uninitialized SGL leads
to BUG() in compare_and_write_callback().
Signed-off-by: Martin Svec <martin.svec@zoner.cz>
Cc: <stable@vger.kernel.org> #3.12+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Ram disk is allocating 8x more space than required for diff data.
For large RAM disk test, there is small potential for memory
starvation.
(Use block_size when calculating total_sg_needed - sagi + nab)
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Cc: <stable@vger.kernel.org> #3.14+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a long-standing bug in iscsit_build_conn_drop_async_message()
where during ERL=2 connection recovery, a bogus conn_p pointer could
end up being used to send the ISCSI_OP_ASYNC_EVENT + DROPPING_CONNECTION
notifying the initiator that cmd->logout_cid has failed.
The bug was manifesting itself as an OOPs in iscsit_allocate_cmd() with
a bogus conn_p pointer in iscsit_build_conn_drop_async_message().
Reported-by: Arshad Hussain <arshad.hussain@calsoftinc.com>
Reported-by: santosh kulkarni <santosh.kulkarni@calsoftinc.com>
Cc: <stable@vger.kernel.org> #3.1+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Fastreg is mandatory for signature, so if the
device doesn't support it we don't need to use it.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a bug where outstanding RDMA_READs with WRITE_PENDING
status require an extra target_put_sess_cmd() in isert_put_cmd() code
when called from isert_cq_tx_comp_err() + isert_cq_drain_comp_llist()
context during session shutdown.
The extra kref PUT is required so that transport_generic_free_cmd()
invokes the last target_put_sess_cmd() -> target_release_cmd_kref(),
which will complete(&se_cmd->cmd_wait_comp) the outstanding se_cmd
descriptor with WRITE_PENDING status, and awake the completion in
target_wait_for_sess_cmds() to invoke TFO->release_cmd().
The bug was manifesting itself in target_wait_for_sess_cmds() where
a se_cmd descriptor with WRITE_PENDING status would end up sleeping
indefinately.
Acked-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: <stable@vger.kernel.org> #3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now that TASK_ABORTED status is not generated for all cases by
TMR ABORT_TASK + LUN_RESET, a new TFO->abort_task() caller is
necessary in order to give fabric drivers a chance to unmap
hardware / software resources before the se_cmd descriptor is
released via the normal TFO->release_cmd() codepath.
This patch adds TFO->aborted_task() in core_tmr_abort_task()
in place of the original transport_send_task_abort(), and
also updates all fabric drivers to implement this caller.
The fabric drivers that include changes to perform cleanup
via ->aborted_task() are:
- iscsi-target
- iser-target
- srpt
- tcm_qla2xxx
The fabric drivers that currently set ->aborted_task() to
NOPs are:
- loopback
- tcm_fc
- usb-gadget
- sbp-target
- vhost-scsi
For the latter five, there appears to be no additional cleanup
required before invoking TFO->release_cmd() to release the
se_cmd descriptor.
v2 changes:
- Move ->aborted_task() call into transport_cmd_finish_abort (Alex)
Cc: Alex Leung <amleung21@yahoo.com>
Cc: Mark Rustad <mark.d.rustad@intel.com>
Cc: Roland Dreier <roland@kernel.org>
Cc: Vu Pham <vu@mellanox.com>
Cc: Chris Boot <bootc@bootc.net>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Cc: Saurav Kashyap <saurav.kashyap@qlogic.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch addresses three of long standing issues wrt to Task
Aborted Status (TAS) handling.
The first is the incorrect assumption in core_tmr_handle_tas_abort()
that TASK_ABORTED status is sent for the task referenced by TMR
ABORT_TASK, and sending TASK_ABORTED status for TMR LUN_RESET on
the same nexus the LUN_RESET was received.
The second is to ensure the lun reference count is dropped within
transport_cmd_finish_abort() by calling transport_lun_remove_cmd()
before invoking transport_cmd_check_stop_to_fabric().
The last is to fix the delayed TAS handling to allow outstanding
WRITEs to complete before sending the TASK_ABORTED status. This
includes changing transport_check_aborted_status() to avoid
processing when SCF_SEND_DELAYED_TAS has not be set, and updating
transport_send_task_abort() to drop the SCF_SENT_DELAYED_TAS
check.
Signed-off-by: Alex Leung <amleung21@yahoo.com>
Cc: Alex Leung <amleung21@yahoo.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes isert_conn_create_fastreg_pool() to follow
logic in iscsi_target_locate_portal() for determining how many
FRMR descriptors to allocate based upon the number of possible
per-session command slots that are available.
This addresses an OOPs in isert_reg_rdma() where due to the
use of ISCSI_DEF_XMIT_CMDS_MAX could end up returning a bogus
fast_reg_descriptor when the number of active tags exceeded
the original hardcoded max.
Note this also includes moving isert_conn_create_fastreg_pool()
from isert_connect_request() to isert_put_login_tx() before
posting the final Login Response PDU in order to determine the
se_nacl->queue_depth (eg: number of tags) per session the target
will be enforcing.
v2 changes:
- Move isert_conn->conn_fr_pool list_head init into
isert_conn_request()
v3 changes:
- Drop unnecessary list_empty() check in isert_reg_rdma()
(Sagi)
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: <stable@vger.kernel.org> #3.12+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
If during data-transfer a data-integrity error was detected we
must fail the command with CHECK_CONDITION and not execute
the command.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Reported-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Remove code duplication from RDMA_READ and RDMA_WRITE
completions that do basically the same check.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
If protection is involved, iSER target must wait for
completion of RDMA_READ before sending SCSI response.
So we must consider that when calculating post_send_buf_count
additions, also when processing good/error completions.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
As REG_SIG_MR work request and it's LOCAL_INVALIDATE are
not accounted in post_send_buf_count we must color these
with ISER_FASTREG_LI_WRID in order to process their error
completions when the QP flushes.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds check for NopOUT->flag (LMB) which is a mandatory
as per RFC 3720 Section 10.18.
(Fix up context changes for v3.14-rc code - nab)
Signed-off-by: Arshad Hussain <arshad.hussain@calsoftinc.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In case the Target core passed transport T10 protection
operation:
1. Register data buffer (data memory region)
2. Register protection buffer if exsists (prot memory region)
3. Register signature region (signature memory region)
- use work request IB_WR_REG_SIG_MR
4. Execute RDMA
5. Upon RDMA completion check the signature status
- if succeeded send good SCSI response
- if failed send SCSI bad response with appropriate sense buffer
(Fix up compile error in isert_reg_sig_mr, and fix up incorrect
se_cmd->prot_type -> TARGET_PROT_NORMAL comparision - nab)
(Fix failed sector assignment in isert_completion_rdma_* - Sagi + nab)
(Fix enum assignements for protection type - Sagi)
(Fix devision on 32-bit in isert_completion_rdma_* - Sagi + Fengguang)
(Fix context change for v3.14-rc6 code - nab)
(Fix iscsit_build_rsp_pdu inc_statsn flag usage - nab)
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In case of protected transactions, we will need to check the
protection status of the transaction before sending SCSI response.
So be ready for RDMA_WRITE completions. currently we don't ask
for these completions, but for T10-PI we will.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Introduce pi_context to hold relevant RDMA protection resources.
We eliminate data_key_valid boolean and replace it with indicators
container to indicate:
- Is the descriptor protected (registered via signature MR)
- Is the data_mr key valid (can spare LOCAL_INV WR)
- Is the prot_mr key valid (can spare LOCAL_INV WR)
- Is the sig_mr key valid (can spare LOCAL_INV WR)
Upon connection establishment check if network portal is T10-PI
enabled and allocate T10-PI resources if necessary, allocate
signature enabled memory regions and mark connection queue-pair
as signature enabled.
(Fix context change for v3.14-rc6 code - nab)
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
export map/unmap data buffer to a routine that may
be used in various places in the code and keep the
mapping data in a designated descriptor. Also, let
isert_fast_reg_mr to decide weather to use global
MR or do fast registration.
This commit does not change any functionality.
(Fix context change for v3.14-rc6 code - nab)
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
User may enable T10-PI support per network portal group. any connection
established on top of it, will be required to serve protected transactions.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In case an iscsi portal group will be defined as t10_pi enabled,
all connections on top of it will support protected transactions.
T10-PI support may require extra reource allocation and maintenance by
the transport layer, so we don't want to apply them on non-t10_pi network
portals. This is a hook for the iscsi target layer to signal the transport
at connection establishment that this connection will carry protected
transactions.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This is not going to be supported soon - so drop it.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Some transports (iSCSI/iSER/SRP/FC) support hardware INSERT/STRIP
capabilities while other transports like loopback/vhost-scsi need
perform this is software.
This patch allows fabrics using SCF_PASSTHROUGH_SG_TO_MEM_NOALLOC
to signal the early LUN scan handling case where PROTECT CDB bits
are set, but no fabric buffer has been provided.
For transports which use generic new command these buffers have yet
to be allocated.
Also this way, target may support protection information
against legacy initiators (writes are inserted and reads
are stripped).
(Only set prot_pto for loopback during early special case - nab)
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
No need to actually compute protection information when formatting
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The Microsoft Surface Type/Touch Cover 2 is a fancy device which advertised
itself as a multitouch device but with constant input reports.
This way, hid_scan_report() gives the group MULTITOUCH to it, but
hid-multitouch can not handle it due to the constant collection ignored
by hid-input.
To prevent such crap in the future, and while we do not fix this particular
device, make the scan_report coherent with hid-input.c, and ignore constant
input reports.
CC: stable@vger.kernel.org # 3.12+
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit 117309c51d.
The MS Surface Pro 2 has an USB composite device with 3 interfaces
- interface 0 - sensor hub
- interface 1 - wacom digitizer
- interface 2 - the keyboard cover, if one is attached
This USB composite device changes it product id dependent on if and which
keyboard cover is attached. Adding the covers to hid_have_special_driver
prevents loading the right hid drivers for the other two interfaces, all 3
get loaded with hid-microsoft. We don't even need hid-microsoft for the
keyboards. We have to revert this to load the right hid modules for each
interface.
CC: stable@vger.kernel.org # kernel 3.14 only
Signed-off-by: Derya <derya.kiran@yahoo.de>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If we remove a file that has inline data after mount, our statistics turns to
inaccurate.
cat /sys/kernel/debug/f2fs/status
- Inline_data Inode: 4294967295
Let's add stat_inc_inline_inode() to stat inline info of the file when lookup.
Change log from v1:
o stat in f2fs_lookup() instead of in do_read_inode() for excluding wrong stat.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Before setting the acl, call posix_acl_valid() to check if it is
valid or not.
Signed-off-by: zhangzhen <zhenzhang.zhang@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
The kbuild test robot reports the following build errors for x86_64-randconfig-c1-0407:
All error/warnings:
net/built-in.o: In function `wiphy_new':
>> (.text+0x7684c): undefined reference to `rfkill_alloc'
net/built-in.o: In function `wiphy_rfkill_start_polling':
>> (.text+0x76da4): undefined reference to `rfkill_resume_polling'
net/built-in.o: In function `wiphy_rfkill_stop_polling':
>> (.text+0x76de9): undefined reference to `rfkill_pause_polling'
net/built-in.o: In function `wiphy_unregister':
>> (.text+0x76ec9): undefined reference to `rfkill_unregister'
net/built-in.o: In function `wiphy_rfkill_set_hw_state':
>> (.text+0x771bc): undefined reference to `rfkill_set_hw_state'
net/built-in.o: In function `wiphy_register':
>> (.text+0x77968): undefined reference to `rfkill_register'
net/built-in.o: In function `wiphy_register':
>> (.text+0x77981): undefined reference to `rfkill_destroy'
net/built-in.o: In function `cfg80211_rfkill_sync_work':
>> core.c:(.text+0x788ad): undefined reference to `rfkill_blocked'
net/built-in.o: In function `cfg80211_dev_free':
>> (.text+0x78a7b): undefined reference to `rfkill_destroy'
net/built-in.o: In function `cfg80211_netdev_notifier_call':
>> core.c:(.text+0x79203): undefined reference to `rfkill_blocked'
net/built-in.o: In function `nl80211_start_p2p_device':
These undefined sysbols are all satisfied if a "select RFKILL" is added to
Kconfig. This "fix" leads to another problem as follows:
>> nl80211.c:(.text+0x9032e): undefined reference to `rfkill_blocked'
net/rfkill/Kconfig:4:error: recursive dependency detected!
net/rfkill/Kconfig:4: symbol RFKILL is selected by R8723AU
drivers/staging/rtl8723au/Kconfig:1: symbol R8723AU depends on USB
drivers/usb/Kconfig:41: symbol USB is selected by MOUSE_APPLETOUCH
drivers/input/mouse/Kconfig:162: symbol MOUSE_APPLETOUCH depends on INPUT
drivers/input/Kconfig:8: symbol INPUT is selected by ACPI_CMPC
drivers/platform/x86/Kconfig:635: symbol ACPI_CMPC depends on RFKILL
To avoid substituting one build error for another, I added a "depends on RFKILL".
My suspicion is that this particular error is caused by a kbuild bug, or that the
selection of INPUT by ACPI_CMPC is wrong. In any case, that will be solved separately.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Jes Sorensen <Jes.Sorensen@redhat.com>
Cc: kbuild-all@01.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some storage devices show relatively high latencies to complete cache_flush
commands, even though their normal IO speed is prettry much high. In such
the case, it needs to merge cache_flush commands as much as possible to avoid
issuing them redundantly.
So, this patch introduces a mount option, "-o flush_merge", to mitigate such
the overhead.
If this option is enabled by user, F2FS merges the cache_flush commands and then
issues just one cache_flush on behalf of them. Once the single command is
finished, F2FS sends a completion signal to all the pending threads.
Note that, this option can be used under a workload consisting of very intensive
concurrent fsync calls, while the storage handles cache_flush commands slowly.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Lets try this again. We can deadlock the box if we send on a box and try to
write onto the same fs with the app that is trying to listen to the send pipe.
This is because the writer could get stuck waiting for a transaction commit
which is being blocked by the send. So fix this by making sure looking at the
commit roots is always going to be consistent. We do this by keeping track of
which roots need to have their commit roots swapped during commit, and then
taking the commit_root_sem and swapping them all at once. Then make sure we
take a read lock on the commit_root_sem in cases where we search the commit root
to make sure we're always looking at a consistent view of the commit roots.
Previously we had problems with this because we would swap a fs tree commit root
and then swap the extent tree commit root independently which would cause the
backref walking code to screw up sometimes. With this patch we no longer
deadlock and pass all the weird send/receive corner cases. Thanks,
Reportedy-by: Hugo Mills <hugo@carfax.org.uk>
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Chris Mason <clm@fb.com>
So I have an awful exercise script that will run snapshot, balance and
send/receive in parallel. This sometimes would crash spectacularly and when it
came back up the fs would be completely hosed. Turns out this is because of a
bad interaction of balance and send/receive. Send will hold onto its entire
path for the whole send, but its blocks could get relocated out from underneath
it, and because it doesn't old tree locks theres nothing to keep this from
happening. So it will go to read in a slot with an old transid, and we could
have re-allocated this block for something else and it could have a completely
different transid. But because we think it is invalid we clear uptodate and
re-read in the block. If we do this before we actually write out the new block
we could write back stale data to the fs, and boom we're screwed.
Now we definitely need to fix this disconnect between send and balance, but we
really really need to not allow ourselves to accidently read in stale data over
new data. So make sure we check if the extent buffer is not under io before
clearing uptodate, this will kick back EIO to the caller instead of reading in
stale data and keep us from corrupting the fs. Thanks,
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Chris Mason <clm@fb.com>
We could have possibly added an extent_op to the locked_ref while we dropped
locked_ref->lock, so check for this case as well and loop around. Otherwise we
could lose flag updates which would lead to extent tree corruption. Thanks,
cc: stable@vger.kernel.org
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Chris Mason <clm@fb.com>
This was done to allow NO_COW to continue to be NO_COW after relocation but it
is not right. When relocating we will convert blocks to FULL_BACKREF that we
relocate. We can leave some of these full backref blocks behind if they are not
cow'ed out during the relocation, like if we fail the relocation with ENOSPC and
then just drop the reloc tree. Then when we go to cow the block again we won't
lookup the extent flags because we won't think there has been a snapshot
recently which means we will do our normal ref drop thing instead of adding back
a tree ref and dropping the shared ref. This will cause btrfs_free_extent to
blow up because it can't find the ref we are trying to free. This was found
with my ref verifying tool. Thanks,
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Chris Mason <clm@fb.com>
OPAL defines opal_msg as a big endian struct so we have to
byte swap it on little endian builds.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The firmware can notify us when new input data is available, so
let's make sure we wakeup the HVC thread in that case.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
