A GPIO driver for the Timberdale FPGA found on the Intel Atom board
Russellville.
The GPIO driver also has an IRQ-chip to support interrupts on the pins.
Signed-off-by: Richard Röjfors <richard.rojfors@mocean-labs.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The wrong test was used, gpio is unsigned and it had an off-by-one.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Alek Du <alek.du@intel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All callsites of x1205_set_datetime() want the date to be set as well, so
remove the flag parameter and set it unconditionally.
Signed-off-by: Johannes Weiner <jw@emlix.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It's possible to have RTC irq shared with other device (e.g.
mpc8349e-mitx board shares ds1339 irq with phy one). Handle this in
driver.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This switches __raw_[read|write]l() for plain [read|write]l in the PL031
RTC driver. The sister driver for PL030 use the simple accessors as most
PrimeCell drivers.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds basic support for Texas Instruments BQ32000 I2C RTC. Only
time reading/writing is implemented. Advanced features, such as trickle
charger and crystal calibration are not supported.
Signed-off-by: Piotr Ziecik <kosmo@semihalf.com>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The rtc-omap driver currently assumes that the rtc's registers are at a
fixed address and already mapped into virtual memory space. Remove those
assumptions so the same driver can be used for similar devices that reside
at different physical addresses (e.g., TI's DA8xx/OMAP-L13x SoC's).
Also allow the possibility for the timer and alarm interrupts to use the
same IRQ.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This driver provides support for the RTC part integrated into the
Freescale MC13783 PMIC and bases on patch created earlier by Sascha
Hauer.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds the Alarm support, this mode enabled when adding
IORESOURCE_IRQ to the platform device resources.
The patch also enables the wakeup mode, so the wakealarm sysfs file (under
/sys/class/rtc/rtcX/) can be used to configure the alarm clock.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add setting and clearing of the "pending" flag of the RTC alarm. The
semantics follow the UEFI specification 2.2 available at
http://www.uefi.org/specs/, i.e., the "pending" flag is cleared by
disabling the alarm, but not by any other condition (such as the passing
of time, a successful wakeup, or setting of a new alarm.)
Signed-off-by: Werner Almesberger <werner@openmoko.org>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Balaji Rao <balajirrao@openmoko.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that we've removed the BKL here, let's explicitly set llseek to
no_llseek since the default llseek is not used here.
The default_llseek function still contains the BKL. When we are auditing
code to see if we can remove the BKL, this is one of the hidden
considerations we need to take into account. i.e., is there
syncronization between code that has the BKL and llseek.
At the same time we remove the BKL it would be a good idea to do indicate
when no llseek function is required, so we don't have to revisit this code
again, when we are trying to determine if we can remove the BKL from the
default_llseek.
Signed-off-by: John Kacur <jkacur@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The to_platform_device macro itself uses container_of macro. Nested use
of container_of macro causes following sparse warnings:
rtc-ds1553.c:259:3: warning: symbol '__mptr' shadows an earlier one
rtc-ds1553.c:259:3: originally declared here
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Alessandro Zummo <alessandro.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: Andrew Sharp <andy.sharp@lsi.com>
Cc: Thomas Hommel <thomas.hommel@gefanuc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Call dev_set_drvdata before rtc device creation.
- Use its own spinlock instead of rtc->irq_lock. Because pdata->rtc
must be initialized to use the irq_lock (pdata->rtc->irq_lock). There
is a small window which rtc methods can be called before pdata->rtc is
initialized.
And there is no need use the irq_lock to protect hardware registers.
The driver's own spinlock shoule be enough.
- Check pdata->rtc before calling rtc_update_irq.
- Use alarm_irq_enable and remove ioctl routine.
- Use devres APIs and simplify error/remove path.
These fixes are ported from ds1553 driver and just compile-tested only.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Alessandro Zummo <alessandro.zummo@towertech.it>
Cc: Thomas Hommel <thomas.hommel@gefanuc.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Call dev_set_drvdata before rtc device creation
* Use its own spinlock instead of rtc->irq_lock
* Check pdata->rtc before calling rtc_update_irq
* Use {alarm,update}_irq_enable and remove ioctl routine
* Use devres APIs and simplify error/remove path
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Use its own spinlock instead of rtc->irq_lock
* Check pdata->rtc before calling rtc_update_irq
* Disable interrupt after rtc_device_unregister
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Call dev_set_drvdata before rtc device creation.
- Use its own spinlock instead of rtc->irq_lock. Because pdata->rtc
must be initialized to use the irq_lock (pdata->rtc->irq_lock). There
is a small window which rtc methods can be called before pdata->rtc is
initialized.
And there is no need use the irq_lock to protect hardware registers.
The driver's own spinlock shoule be enough.
- Check pdata->rtc before calling rtc_update_irq.
- Use {alarm,update}_irq_enable and remove ioctl routine.
- Use devres APIs and simplify error/remove path.
These fixes are ported from ds1553 driver and just compile-tested only.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Andrew Sharp <andy.sharp@lsi.com>
Cc: Thomas Hommel <thomas.hommel@gefanuc.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Drop ioctl function that handles RTC_AIE/RTC_UIE, and use instead the
rtc subsystem API (alarm_irq_enable/update_irq_enable callbacks).
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Herton Ronaldo Krzesinski recently raised up, and fixed, an issue with the
rtc_cmos driver, which was referring to an inconsistent driver data.
This patch ensures that driver data registration happens before
rtc_device_register().
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: Thomas Hommel <thomas.hommel@gefanuc.com>
Acked-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Andrew Sharp <andy.sharp@onstor.com>
Cc: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Alexander Bigga <ab@mycable.de>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Mark Zhan <rongkai.zhan@windriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I noticed that rtc wont generate interrupts after a resume from disk.
Here hpet rtc emulation is used.
Problem is that rtc hpet comparator, isn't reinitialized after resume.
Easiest way to solve this, is always mask all hpet interrupts on suspend
This is triggered, when suspending with alarm set.
Otherwise, hpet driver will think it doesn't need to reinitialize
the rtc comparator, thus rtc interrupts won't work.
This emulation isn't need for wakealarm.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We need to be able to cope with the directory mutex being held during
->d_revalidate() in some cases, but not all cases, and not necessarily by
us. Because we need to release the mutex when we call back to the daemon
to do perform a mount we must be sure that it is us who holds the mutex so
we must redirect mount requests to ->lookup() if the mutex is held.
Signed-off-by: Ian Kent <raven@themaw.net>
Cc: Sage Weil <sage@newdream.net>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Andreas Dilger <adilger@sun.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Yehuda Saheh <yehuda@newdream.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In autofs4_lookup_expiring() a declaration within the list traversal loop
uses a declaration that has the same name as the function parameter.
Signed-off-by: Ian Kent <raven@themaw.net>
Cc: Sage Weil <sage@newdream.net>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Andreas Dilger <adilger@sun.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Yehuda Saheh <yehuda@newdream.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In autofs4_lookup_active() a declaration within the list traversal loop
uses a declaration that has the same name as the function parameter.
Signed-off-by: Ian Kent <raven@themaw.net>
Cc: Sage Weil <sage@newdream.net>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Andreas Dilger <adilger@sun.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Yehuda Saheh <yehuda@newdream.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We unhash the dentry (in a subsequent patch) in ->d_revalidate() in order
to send mount requests to ->lookup(). But then we can not rely on
d_unhased() to give reliable results because it may be called at any time
by any code path. The d_unhashed() function is used by __simple_empty()
in the path walking callbacks but autofs mount point dentrys should have
no directories at all so a list_empty() on d_subdirs should be (and is)
sufficient.
Signed-off-by: Ian Kent <raven@themaw.net>
Cc: Sage Weil <sage@newdream.net>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Andreas Dilger <adilger@sun.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Yehuda Saheh <yehuda@newdream.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The lookup functions for active and expiring dentrys use parameters that
can be easily obtained on entry so we change the call to to take just the
dentry. This makes the subsequent change, to send all lookups to
->lookup(), a bit cleaner.
Signed-off-by: Ian Kent <raven@themaw.net>
Cc: Sage Weil <sage@newdream.net>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Andreas Dilger <adilger@sun.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Yehuda Saheh <yehuda@newdream.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rename the variable unhashed to active in autofs4_lookup() to better
reflect its usage.
Signed-off-by: Ian Kent <raven@themaw.net>
Cc: Sage Weil <sage@newdream.net>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Andreas Dilger <adilger@sun.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Yehuda Saheh <yehuda@newdream.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Eliminate the use of the d_lock spin lock by using the autofs super block
info spin lock. This reduces the number of spin locks we use by one and
makes the code for the following patch (to redirect ->d_revalidate() to
->lookup()) a little simpler.
Signed-off-by: Ian Kent <raven@themaw.net>
Cc: Sage Weil <sage@newdream.net>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Andreas Dilger <adilger@sun.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Yehuda Saheh <yehuda@newdream.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Define simple helper function for checking if we need to trigger a mount.
Signed-off-by: Ian Kent <raven@themaw.net>
Cc: Sage Weil <sage@newdream.net>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Andreas Dilger <adilger@sun.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Yehuda Saheh <yehuda@newdream.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Define some simple helper functions for adding and deleting entries on the
expiring dentry list.
Signed-off-by: Ian Kent <raven@themaw.net>
Cc: Sage Weil <sage@newdream.net>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Andreas Dilger <adilger@sun.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Yehuda Saheh <yehuda@newdream.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Define some simple helper functions for adding and deleting entries on the
active (and unhashed) dentry list.
Signed-off-by: Ian Kent <raven@themaw.net>
Cc: Sage Weil <sage@newdream.net>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Andreas Dilger <adilger@sun.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Yehuda Saheh <yehuda@newdream.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For embedded systems, the blinking cursor at startup time can be annoying
and unintended. Add a new kernel parameter to change the default cursor
shape.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: Daniel Mack <daniel@caiaq.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: David Newall <davidn@davidnewall.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* de_get() is trivial -- make inline, save a few bits of code, drop
"refcount is 0" check -- it should be done in some generic refcount
code, don't recall it's was helpful
* rename GET and PUT functions to pde_get(), pde_put() for cool prefix!
* remove obvious and incorrent comments
* in remove_proc_entry() use pde_put(), when I fixed PDE refcounting to
be normal one, remove_proc_entry() was supposed to do "-1" and code now
reflects that.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ktime will overflow from 03:14:07 UTC on Tuesday, 19 January 2038,
ktime_add() in timecompare_update() will overflow a half earlier. As a
result, wrong offset will be gotten, then cause some strange problems.
Signed-off-by: Barry Song <21cnbao@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Patrick Ohly <patrick.ohly@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix node-oriented allocation handling in oom-kill.c I myself think of this
as a bugfix not as an ehnancement.
In these days, things are changed as
- alloc_pages() eats nodemask as its arguments, __alloc_pages_nodemask().
- mempolicy don't maintain its own private zonelists.
(And cpuset doesn't use nodemask for __alloc_pages_nodemask())
So, current oom-killer's check function is wrong.
This patch does
- check nodemask, if nodemask && nodemask doesn't cover all
node_states[N_HIGH_MEMORY], this is CONSTRAINT_MEMORY_POLICY.
- Scan all zonelist under nodemask, if it hits cpuset's wall
this faiulre is from cpuset.
And
- modifies the caller of out_of_memory not to call oom if __GFP_THISNODE.
This doesn't change "current" behavior. If callers use __GFP_THISNODE
it should handle "page allocation failure" by itself.
- handle __GFP_NOFAIL+__GFP_THISNODE path.
This is something like a FIXME but this gfpmask is not used now.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hioryu@jp.fujitsu.com>
Acked-by: David Rientjes <rientjes@google.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Christoph Lameter <cl@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In a typical oom analysis scenario, we frequently want to know whether the
killed process has a memory leak or not at the first step. This patch
adds vsz and rss information to the oom log to help this analysis. To
save time for the debugging.
example:
===================================================================
rsyslogd invoked oom-killer: gfp_mask=0x201da, order=0, oom_adj=0
Pid: 1308, comm: rsyslogd Not tainted 2.6.32-rc6 #24
Call Trace:
[<ffffffff8132e35b>] ?_spin_unlock+0x2b/0x40
[<ffffffff810f186e>] oom_kill_process+0xbe/0x2b0
(snip)
492283 pages non-shared
Out of memory: kill process 2341 (memhog) score 527276 or a child
Killed process 2341 (memhog) vsz:1054552kB, anon-rss:970588kB, file-rss:4kB
===========================================================================
^
|
here
[rientjes@google.com: fix race, add pid & comm to message]
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 5ad6468801 "ksm: let shared pages
be swappable" breaks the build on m68knommu and I suspect on any nommu:
In file included from kernel/fork.c:52:
include/linux/ksm.h:129: warning: 'enum ttu_flags' declared inside parameter list
include/linux/ksm.h:129: warning: its scope is only this definition or declaration, which is probably not what you want
include/linux/ksm.h:129: error: parameter 2 ('flags') has incomplete type
make[1]: *** [kernel/fork.o] Error 1
make[1]: *** Waiting for unfinished jobs....
Let's fix that with CONFIG_MMU around most of the !CONFIG_KSM declarations.
Reported-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Tested-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Take advantage of the new events capabilities of the backlight class to
notify userspace of backlight changes.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
The LT3593 is a step-up DC/DC converter designed to drive up to ten
white LEDs in series. The current flow can be set with a control pin.
This driver controls any number of such devices connected on generic
GPIOs and exports the function as as platform_driver.
The gpio_led platform data struct definition is reused for this purpose.
Successfully tested on a PXA embedded board.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
pci_enable_result is defined using the __must_check macro but
leds-ss4200 is not checking the return value.
Signed-off-by: Javier Martinez Canillas <martinez.javier@gmail.com>
Signed-off-by: Dave Hansen <dave@sr71.net>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
This makes the LEDs driver for ALIX2.C boards work with Coreboot by
looking up the port address in the MSR rather than hard-coding it.
The BIOS scan also needed some tweaks as the string in Coreboot differs
from the one in the legacy BIOS.
Successfully tested with both the legacy tinyBIOS as well as Coreboot
v3.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
This code is based on a driver that came in the "Open-source
and GPL components" download here:
http://downloadcenter.intel.com/SearchResult.aspx?lang=eng&ProductFamily=Server+Products&ProductLine=Intel%C2%AE+Storage+Systems&ProductProduct=Intel%C2%AE+Entry+Storage+System+SS4200-E&OSVersion=OS+Independent
It was in a file called nasgpio.c inside of a second zip file
called SS4200-E_Linux_SIO_Driver-v1.4.zip and is based on this
updated to use the LED subsystem with the ioctl and hardware
monitor support removed.
I don't have any need for brightness
control, and its code is *completely* separate from the on/off
controls implemented here. If anyone else wants it, I'd be
happy to look into adding it, but I don't care enough for now.
Except for the probe routines, I rewrote most of it. I also
Note that I don't have any hardware documentation except for
the original driver.
Thanks go to Arjan for his help in getting the original source
for this released and for chasing down some licensing issues.
Signed-off-by: Dave Hansen <dave@sr71.net>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Driver needs to #include <sched.h>:
drivers/media/radio/si470x/radio-si470x-common.c:452: error: 'TASK_INTERRUPTIBLE' undeclared (first use in this function)
drivers/media/radio/si470x/radio-si470x-common.c:452: error: implicit declaration of function 'signal_pending'
drivers/media/radio/si470x/radio-si470x-common.c:452: error: implicit declaration of function 'schedule'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make the local filter coefficients static and const. This will eliminate the
following sparse warnings (see "make C=1"):
* au8522_decoder.c:71:31: warning: symbol 'filter_coef' was not declared. Should it be static?
* au8522_decoder.c:113:31: warning: symbol 'lpfilter_coef' was not declared. Should it be static?
Signed-off-by: Márton Németh <nm127@freemail.hu>
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
