./usr/include/linux/netfilter/xt_SYNPROXY.h:11: found __[us]{8,16,32,64} type without #include <linux/types.h>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Matt Whitlock says:
Without this line, the file xt_SYNPROXY.h does not get installed in
/usr/include/linux/netfilter/, and thus user-space programs cannot make
use of it.
Reported-by: Matt Whitlock <kernel@mattwhitlock.name>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Bypass support was added in commit d38018f201 ("regulator: anatop: Add
bypass support to digital LDOs"). A check for valid voltage selectors was
added in commit da0607c8df ("regulator: anatop: Fail on invalid voltage
selector") but it also discards all regulators that are in bypass mode. Add
check for the bypass setting. Errors below were seen on a Variscite mx6
board.
anatop_regulator 20c8000.anatop:regulator-vddcore@140: Failed to read a valid default voltage selector.
anatop_regulator: probe of 20c8000.anatop:regulator-vddcore@140 failed with error -22
anatop_regulator 20c8000.anatop:regulator-vddsoc@140: Failed to read a valid default voltage selector.
anatop_regulator: probe of 20c8000.anatop:regulator-vddsoc@140 failed with error -22
Fixes: da0607c8df ("regulator: anatop: Fail on invalid voltage selector")
Signed-off-by: Mika Båtsman <mbatsman@mvista.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Based on the latest timing specifications for the TPS65218 from the data
sheet, http://www.ti.com/lit/ds/symlink/tps65218.pdf, document SLDS206
from November 2014, we must change the i2c bus speed to better fit within
the minimum high SCL time required for proper i2c transfer.
When running at 400khz, measurements show that SCL spends
0.8125 uS/1.666 uS high/low which violates the requirement for minimum
high period of SCL provided in datasheet Table 7.6 which is 1 uS.
Switching to 100khz gives us 5 uS/5 uS high/low which both fall above
the minimum given values for 100 khz, 4.0 uS/4.7 uS high/low.
Without this patch occasionally a voltage set operation from the kernel
will appear to have worked but the actual voltage reflected on the PMIC
will not have updated, causing problems especially with cpufreq that may
update to a higher OPP without actually raising the voltage on DCDC2,
leading to a hang.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Aparna Balasubramanian <aparnab@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The PE primary bus cannot be got from its child devices when having
full hotplug in error recovery. The PE primary bus is cached, which
is done in commit <05ba75f848> ("powerpc/eeh: Fix stale cached primary
bus"). In eeh_reset_device(), the flag (EEH_PE_PRI_BUS) is cleared
before the PCI hot remove. eeh_pe_bus_get() then returns NULL as the
PE primary bus in pnv_eeh_reset() and it crashes the kernel eventually.
This fixes the issue by clearing the flag (EEH_PE_PRI_BUS) before the
PCI hot add. With it, the PowerNV EEH reset backend (pnv_eeh_reset())
can get valid PE primary bus through eeh_pe_bus_get().
Fixes: 67086e32b5 ("powerpc/eeh: powerpc/eeh: Support error recovery for VF PE")
Reported-by: Pridhiviraj Paidipeddi <ppaiddipe@in.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
ISA 3.0 updated it to be encoded as Radix tree size = 2^(RTS + 31). We
have it encoded as 2^(RTS + 28). Add a helper with the correct encoding
and use it instead of opencoding.
Fixes: 2bfd65e45e ("powerpc/mm/radix: Add radix callbacks for early init routines")
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
H_ENTER hcall handling in qemu had assumptions that a cache inhibited
hpte entry won't have memory conference set. Also older kernel
mentioned that some version of pHyp required this (the code removed
by the below commit says:
/* Make pHyp happy */
if ((rflags & _PAGE_NO_CACHE) && !(rflags & _PAGE_WRITETHRU))
hpte_r &= ~HPTE_R_M;
But with older kernel we had some inconsistent memory conherence
mapping. We always enabled memory conherence in the page fault path and
removed memory conherence is _PAGE_NO_CACHE was set when we mapped the
page via htab_bolt_mapping. The commit mentioned below tried to
consolidate that by always enabling memory conherence. But as mentioned
above that breaks Qemu H_ENTER handling.
This patch update this such that we enable memory conherence only if
cache inhibited is not set and bring fault handling, lpar and bolt
mapping in sync.
Fixes: commit 30bda41aba4e("powerpc/mm: Drop WIMG in favour of new constant")
Reported-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
A few platforms are currently missing clocksource_probe() completely
in their time_init functionality. On OMAP3430 for example, this is
causing cpuidle to be pretty much dead, as the counter32k is not
going to be registered and instead a gptimer is used as a clocksource.
This will tick in periodic mode, preventing any deeper idle states.
While here, also drop one unnecessary check for populated DT before
existing clocksource_probe() call.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
After OMAP1 IRQ definitions have been changed by commit 685e2d08c5
("ARM: OMAP1: Change interrupt numbering for sparse IRQ") introduced
in v4.2, ams-delta FIQ handler which depends on them no longer works
as expected. Fix it.
Created and tested on Amstrad Delta against Linux-4.7-rc3
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This seems to be required on some X58 chipsets on systems
with more than one IOMMU. QI does not work until it is
enabled on all IOMMUs in the system.
Reported-by: Dheeraj CVR <cvr.dheeraj@gmail.com>
Tested-by: Dheeraj CVR <cvr.dheeraj@gmail.com>
Fixes: 5f0a7f7614 ('iommu/vt-d: Make root entry visible for hardware right after allocation')
Cc: stable@vger.kernel.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
We were using an incorrect define to get the irq vector number.
NFP_NET_CFG_LSC is a control BAR offset, LSC interrupt vector
index is called NFP_NET_IRQ_LSC_IDX. For machines with less
than 30 CPUs this meant that we were disabling/enabling IRQ 0.
For bigger hosts we were just playing with the 31st RX/TX
interrupt.
Fixes: 0ba40af963 ("nfp: move link state interrupt request/free calls")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These changes fix a bit of fallout from the introduction of the atomic
API.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=usLT
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-4.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm fixes from Thierry Reding:
"These changes fix a bit of fallout from the introduction of the atomic
API"
* tag 'pwm/for-4.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: atmel-hlcdc: Fix default PWM polarity
pwm: sysfs: Get return value from pwm_apply_state()
pwm: Improve args checking in pwm_apply_state()
- One new kvm_stat for s390
- Correctly disable VT-d posted interrupts with the rest of posted interrupts
- "make randconfig" fix for x86 AMD
- Off-by-one in irq route check (the "good" kind that errors out a bit too
early!)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJXYrXKAAoJEL/70l94x66D1MUH/i9kPqfDq+XveHyiY4ovI2Vl
lD1P0dJoXPRjrJJ/LRulr3TiGDVsW6QZ8SnA5QNQvxDdlc7CzS8ZgqaiLPUh8TKJ
OofVUaFgm77MDvGJuJOOJ159ghO+7KwPsq1P05xpO2HRxAD+q1/u1yjfOz7fIEqC
iMne68rfv0OeiMlBOo8G2e1Xmtk1GKNBhmRItUgOF/jVtP2RSvV5o+2rcQ5LS3g6
KV/fpWtRumd3R+TdRvacjADgvWrSokDfph+Ha9qp7sBjkVGLLZ/hdHzTzIimXKF6
x4muv1HYzKSGaCJB2yMLYuy/KJ8zbsk7co0bjn1SmzrSweJxMkDGwLp1Ffau6iM=
=N4kr
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
- miscellaneous fixes for MIPS and s390
- one new kvm_stat for s390
- correctly disable VT-d posted interrupts with the rest of posted
interrupts
- "make randconfig" fix for x86 AMD
- off-by-one in irq route check (the "good" kind that errors out a bit
too early!)
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm: vmx: check apicv is active before using VT-d posted interrupt
kvm: Fix irq route entries exceeding KVM_MAX_IRQ_ROUTES
kvm: svm: Do not support AVIC if not CONFIG_X86_LOCAL_APIC
kvm: svm: Fix implicit declaration for __default_cpu_present_to_apicid()
MIPS: KVM: Fix CACHE triggered exception emulation
MIPS: KVM: Don't unwind PC when emulating CACHE
MIPS: KVM: Include bit 31 in segment matches
MIPS: KVM: Fix modular KVM under QEMU
KVM: s390: Add stats for PEI events
KVM: s390: ignore IBC if zero
to the big nfs4_lock_state removal around 3.17 (but that were also
probably hard to reproduce before client changes in 3.20 allowed the
client to perform parallel opens).
Also fix a 4.1 backchannel crash due to rpc multipath changes in 4.6.
Trond acked the client-side rpc fixes going through my tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=aNkl
-----END PGP SIGNATURE-----
Merge tag 'nfsd-4.7-1' of git://linux-nfs.org/~bfields/linux
Pull nfsd bugfixes from Bruce Fields:
"Oleg Drokin found and fixed races in the nfsd4 state code that go back
to the big nfs4_lock_state removal around 3.17 (but that were also
probably hard to reproduce before client changes in 3.20 allowed the
client to perform parallel opens).
Also fix a 4.1 backchannel crash due to rpc multipath changes in 4.6.
Trond acked the client-side rpc fixes going through my tree"
* tag 'nfsd-4.7-1' of git://linux-nfs.org/~bfields/linux:
nfsd: Make init_open_stateid() a bit more whole
nfsd: Extend the mutex holding region around in nfsd4_process_open2()
nfsd: Always lock state exclusively.
rpc: share one xps between all backchannels
nfsd4/rpc: move backchannel create logic into rpc code
SUNRPC: fix xprt leak on xps allocation failure
nfsd: Fix NFSD_MDS_PR_KEY on 32-bit by adding ULL postfix
Pull overlayfs fixes from Miklos Szeredi:
"This contains two regression fixes: one for the xattr API update and
one for using the mounter's creds in file creation in overlayfs.
There's also a fix for a bug in handling hard linked AF_UNIX sockets
that's been there from day one. This fix is overlayfs only despite
the fact that it touches code outside the overlay filesystem: d_real()
is an identity function for all except overlay dentries"
* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
ovl: fix uid/gid when creating over whiteout
ovl: xattr filter fix
af_unix: fix hard linked sockets on overlay
vfs: add d_real_inode() helper
If __key_link_begin() failed then "edit" would be uninitialized. I've
added a check to fix that.
This allows a random user to crash the kernel, though it's quite
difficult to achieve. There are three ways it can be done as the user
would have to cause an error to occur in __key_link():
(1) Cause the kernel to run out of memory. In practice, this is difficult
to achieve without ENOMEM cropping up elsewhere and aborting the
attempt.
(2) Revoke the destination keyring between the keyring ID being looked up
and it being tested for revocation. In practice, this is difficult to
time correctly because the KEYCTL_REJECT function can only be used
from the request-key upcall process. Further, users can only make use
of what's in /sbin/request-key.conf, though this does including a
rejection debugging test - which means that the destination keyring
has to be the caller's session keyring in practice.
(3) Have just enough key quota available to create a key, a new session
keyring for the upcall and a link in the session keyring, but not then
sufficient quota to create a link in the nominated destination keyring
so that it fails with EDQUOT.
The bug can be triggered using option (3) above using something like the
following:
echo 80 >/proc/sys/kernel/keys/root_maxbytes
keyctl request2 user debug:fred negate @t
The above sets the quota to something much lower (80) to make the bug
easier to trigger, but this is dependent on the system. Note also that
the name of the keyring created contains a random number that may be
between 1 and 10 characters in size, so may throw the test off by
changing the amount of quota used.
Assuming the failure occurs, something like the following will be seen:
kfree_debugcheck: out of range ptr 6b6b6b6b6b6b6b68h
------------[ cut here ]------------
kernel BUG at ../mm/slab.c:2821!
...
RIP: 0010:[<ffffffff811600f9>] kfree_debugcheck+0x20/0x25
RSP: 0018:ffff8804014a7de8 EFLAGS: 00010092
RAX: 0000000000000034 RBX: 6b6b6b6b6b6b6b68 RCX: 0000000000000000
RDX: 0000000000040001 RSI: 00000000000000f6 RDI: 0000000000000300
RBP: ffff8804014a7df0 R08: 0000000000000001 R09: 0000000000000000
R10: ffff8804014a7e68 R11: 0000000000000054 R12: 0000000000000202
R13: ffffffff81318a66 R14: 0000000000000000 R15: 0000000000000001
...
Call Trace:
kfree+0xde/0x1bc
assoc_array_cancel_edit+0x1f/0x36
__key_link_end+0x55/0x63
key_reject_and_link+0x124/0x155
keyctl_reject_key+0xb6/0xe0
keyctl_negate_key+0x10/0x12
SyS_keyctl+0x9f/0xe7
do_syscall_64+0x63/0x13a
entry_SYSCALL64_slow_path+0x25/0x25
Fixes: f70e2e0619 ('KEYS: Do preallocation for __key_link()')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since 32b8a8e59c ("sit: add IPv4 over IPv4 support")
ipip6_err() may be called for packets whose IP protocol is
IPPROTO_IPIP as well as those whose IP protocol is IPPROTO_IPV6.
In the case of IPPROTO_IPIP packets the correct protocol value is not
passed to ipv4_update_pmtu() or ipv4_redirect().
This patch resolves this problem by using the IP protocol of the packet
rather than a hard-coded value. This appears to be consistent
with the usage of the protocol of a packet by icmp_socket_deliver()
the caller of ipip6_err().
I was able to exercise the redirect case by using a setup where an ICMP
redirect was received for the destination of the encapsulated packet.
However, it appears that although incorrect the protocol field is not used
in this case and thus no problem manifests. On inspection it does not
appear that a problem will manifest in the fragmentation needed/update pmtu
case either.
In short I believe this is a cosmetic fix. None the less, the use of
IPPROTO_IPV6 seems wrong and confusing.
Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If percpu_ref initialization fails during css_create(), the free path
can end up trying to free css->id of zero. As ID 0 is unused, it
doesn't cause a critical breakage but it does trigger a warning
message. Fix it by setting css->id to -1 from init_and_link_css().
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Wenwei Tao <ww.tao0320@gmail.com>
Fixes: 01e586598b ("cgroup: release css->id after css_free")
Cc: stable@vger.kernel.org # v4.0+
Signed-off-by: Tejun Heo <tj@kernel.org>
The mlx4e driver does not support more than one port for VXLAN offload. As
such expecting the hardware to offload other ports is invalid since it
appears the parsing logic is used to perform Tx checksum and segmentation
offloads. Use the vxlan_port number to determine in which cases we can
apply the offload and in which cases we can not.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building with -Wextra, we get a harmless warning from the
EFX_EXTRACT_OWORD32 macro:
ethernet/sfc/farch.c: In function 'efx_farch_test_registers':
ethernet/sfc/farch.c:119:30: error: comparison of unsigned expression < 0 is always false [-Werror=type-limits]
ethernet/sfc/farch.c:124:144: error: comparison of unsigned expression < 0 is always false [-Werror=type-limits]
ethernet/sfc/farch.c:124:392: error: comparison of unsigned expression < 0 is always false [-Werror=type-limits]
ethernet/sfc/farch.c:124:731: error: comparison of unsigned expression < 0 is always false [-Werror=type-limits]
The macro and the caller are both correct, but we can avoid the
warning by changing the index variable to a signed type.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current versions of gdb do not interoperate cleanly with kgdb on arm64
systems because gdb and kgdb do not use the same register description.
This patch modifies kgdb to work with recent releases of gdb (>= 7.8.1).
Compatibility with gdb (after the patch is applied) is as follows:
gdb-7.6 and earlier Ok
gdb-7.7 series Works if user provides custom target description
gdb-7.8(.0) Works if user provides custom target description
gdb-7.8.1 and later Ok
When commit 44679a4f14 ("arm64: KGDB: Add step debugging support") was
introduced it was paired with a gdb patch that made an incompatible
change to the gdbserver protocol. This patch was eventually merged into
the gdb sources:
https://sourceware.org/git/gitweb.cgi?p=binutils-gdb.git;a=commit;h=a4d9ba85ec5597a6a556afe26b712e878374b9dd
The change to the protocol was mostly made to simplify big-endian support
inside the kernel gdb stub. Unfortunately the gdb project released
gdb-7.7.x and gdb-7.8.0 before the protocol incompatibility was identified
and reversed:
https://sourceware.org/git/gitweb.cgi?p=binutils-gdb.git;a=commit;h=bdc144174bcb11e808b4e73089b850cf9620a7ee
This leaves us in a position where kgdb still uses the no-longer-used
protocol; gdb-7.8.1, which restored the original behaviour, was
released on 2014-10-29.
I don't believe it is possible to detect/correct the protocol
incompatiblity which means the kernel must take a view about which
version of the gdb remote protocol is "correct". This patch takes the
view that the original/current version of the protocol is correct
and that version found in gdb-7.7.x and gdb-7.8.0 is anomalous.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
ath.git fixes for 4.7. Major changes:
ath9k
* fix GPIO mask regression with AR9462 and AR9565
ath10k
* fix deadlock while processing rx_in_ord_ind
* fix crash related to printing firmware features in debug mode
* fix deadlock when peer cannot be created
path_b_ok is being assigned but immediately after path_a_ok is being
compared to the value 0x03. This appears to be a typo on the
variable name, compare path_b_ok instead.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This bug leads to:
[ 1.906411] Unable to handle kernel NULL pointer dereference at virtual address 0000000c
[ 1.914878] pgd = c0004000
[ 1.917786] [0000000c] *pgd=00000000
[ 1.921536] Internal error: Oops: 5 [#1] SMP ARM
[ 1.926357] Modules linked in:
[ 1.929556] CPU: 0 PID: 14 Comm: kworker/0:1 Not tainted 4.4.5 #18
[ 1.936006] Hardware name: Generic AM33XX (Flattened Device Tree)
[ 1.942383] Workqueue: events power_supply_changed_work
[ 1.947842] task: de2c41c0 ti: de2c8000 task.ti: de2c8000
[ 1.953483] PC is at tps65217_ac_get_property+0x14/0x28
[ 1.958937] LR is at tps65217_ac_get_property+0x10/0x28
Driver was trying to use drv_data in property get handler. However drv_data
was not set, so it caused NULL pointer dereference. This patch properly
sets drv_data during probe by power_supply_config parameter, so the
property get handler works as desired.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Fixes: 3636859b28 ("power_supply: Add support for tps65217-charger")
Signed-off-by: Sebastian Reichel <sre@kernel.org>
dev_pm_opp_get_sharing_cpus() returns 0 even in the case when the OPP
core doesn't know whether or not the table is shared. It works on the
majority of platforms, where the OPP table is never created before
invoking the function and then -ENODEV is returned by it.
But in the case of one platform (Jetson TK1) at least, the situation
is a bit different. The OPP table has been created (somehow) before
dev_pm_opp_get_sharing_cpus() is called and it returns 0. Its caller
treats that as 'the CPUs don't share OPPs' and that leads to degraded
performance.
Fix this by converting 'shared_opp' in struct opp_table to an enum
and making dev_pm_opp_get_sharing_cpus() return -EINVAL in case when
the value of that field is "access unknown", so that the caller can
handle it accordingly (cpufreq-dt considers that as 'all CPUs share
the table', for example).
Fixes: 6f707daa38 "PM / OPP: Add dev_pm_opp_get_sharing_cpus()"
Reported-and-tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
[ rjw : Subject & changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In the omap gpmc driver it can be noticed that GPMC_CONFIG4_OEEXTRADELAY
is overwritten by the WEEXTRADELAY value from the device tree and
GPMC_CONFIG4_WEEXTRADELAY is not updated by the value from the device
tree.
As a consequence, the memory accesses cannot be configured properly when
the extra delay are needed for OE and WE.
Fix the update of GPMC_CONFIG4_WEEXTRADELAY with the value from the
device tree file and prevents GPMC_CONFIG4_OEXTRADELAY
being overwritten by the WEXTRADELAY value from the device tree.
Cc: stable@vger.kernel.org
Signed-off-by: Ocquidant, Sebastien <sebastienocquidant@eaton.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
VT-d posted interrupt is relying on the CPU side's posted interrupt.
Need to check whether VCPU's APICv is active before enabing VT-d
posted interrupt.
Fixes: d62caabb41
Cc: stable@vger.kernel.org
Signed-off-by: Yang Zhang <yang.zhang.wz@gmail.com>
Signed-off-by: Shengge Ding <shengge.dsg@alibaba-inc.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
These days, we experienced one guest crash with 8 cores and 3 disks,
with qemu error logs as bellow:
qemu-system-x86_64: /build/qemu-2.0.0/kvm-all.c:984:
kvm_irqchip_commit_routes: Assertion `ret == 0' failed.
And then we found one patch(bdf026317d) in qemu tree, which said
could fix this bug.
Execute the following script will reproduce the BUG quickly:
irq_affinity.sh
========================================================================
vda_irq_num=25
vdb_irq_num=27
while [ 1 ]
do
for irq in {1,2,4,8,10,20,40,80}
do
echo $irq > /proc/irq/$vda_irq_num/smp_affinity
echo $irq > /proc/irq/$vdb_irq_num/smp_affinity
dd if=/dev/vda of=/dev/zero bs=4K count=100 iflag=direct
dd if=/dev/vdb of=/dev/zero bs=4K count=100 iflag=direct
done
done
========================================================================
The following qemu log is added in the qemu code and is displayed when
this bug reproduced:
kvm_irqchip_commit_routes: max gsi: 1008, nr_allocated_irq_routes: 1024,
irq_routes->nr: 1024, gsi_count: 1024.
That's to say when irq_routes->nr == 1024, there are 1024 routing entries,
but in the kernel code when routes->nr >= 1024, will just return -EINVAL;
The nr is the number of the routing entries which is in of
[1 ~ KVM_MAX_IRQ_ROUTES], not the index in [0 ~ KVM_MAX_IRQ_ROUTES - 1].
This patch fix the BUG above.
Cc: stable@vger.kernel.org
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: Wei Tang <tangwei@cmss.chinamobile.com>
Signed-off-by: Zhang Zhuoyu <zhangzhuoyu@cmss.chinamobile.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Enabling a component via sysfs (echo 1 > enable_source), would
trigger building a path from the enabled sources to the sink.
If there is an error in the process (e.g, sink not enabled or
the device (CPU corresponding to ETM) is not online), we never report
failure, except for leaving a message in the dmesg.
Do proper error checking for the build path and return the error.
Before:
$ echo 0 > /sys/devices/system/cpu/cpu2/online
$ echo 1 > /sys/devices/cs_etm/cpu2/enable_source
$ echo $?
0
After:
$ echo 0 > /sys/devices/system/cpu/cpu2/online
$ echo 1 > /sys/devices/cs_etm/cpu2/enable_source
-bash: echo: write error: No such device or address
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At the end of a trace collection, we try to clear the entire buffer
and enable the ETR back if it was already enabled. But, we would have
adjusted the drvdata->buf to point to the beginning of the trace data
in the trace buffer @drvdata->vaddr. So, the following code which
clears the buffer is dangerous and can cause crashes, like below :
memset(drvdata->buf, 0, drvdata->size);
Unable to handle kernel paging request at virtual address ffffff800a145000
pgd = ffffffc974726000
*pgd=00000009f3e91003, *pud=00000009f3e91003, *pmd=0000000000000000
PREEMPT SMP
Modules linked in:
CPU: 4 PID: 1692 Comm: dd Not tainted 4.7.0-rc2+ #1721
Hardware name: ARM Juno development board (r0) (DT)
task: ffffffc9734a0080 ti: ffffffc974460000 task.ti: ffffffc974460000
PC is at __memset+0x1ac/0x200
LR is at tmc_read_unprepare_etr+0x144/0x1bc
pc : [<ffffff80083a05ac>] lr : [<ffffff800859c984>] pstate: 200001c5
...
[<ffffff80083a05ac>] __memset+0x1ac/0x200
[<ffffff800859b2e4>] tmc_release+0x90/0x94
[<ffffff8008202f58>] __fput+0xa8/0x1ec
[<ffffff80082030f4>] ____fput+0xc/0x14
[<ffffff80080c3ef8>] task_work_run+0xb0/0xe4
[<ffffff8008088bf4>] do_notify_resume+0x64/0x6c
[<ffffff8008084d5c>] work_pending+0x10/0x14
Code: 91010108 54ffff4a 8b040108 cb050042 (d50b7428)
Since we clear the buffer anyway in the following call to
tmc_etr_enable_hw(), remove the erroneous memset().
Fixes: commit de5461970b ("coresight: tmc: allocating memory when needed")
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At the end of the trace capture, we free the allocated memory,
resetting the drvdata->buf to NULL, to indicate that trace data
was collected and the next trace session should allocate the
memory in tmc_enable_etr_sink_sysfs.
The tmc_enable_etr_sink_sysfs, we only allocate memory if drvdata->vaddr
is not NULL (which is not performed at the end of previous session).
This can cause, drvdata->vaddr getting assigned NULL and later we do
memset() which causes a crash as below :
Unable to handle kernel NULL pointer dereference at virtual
address 00000000
pgd = ffffffc9747f0000
[00000000] *pgd=00000009f402e003, *pud=00000009f402e003,
*pmd=0000000000000000
Internal error: Oops: 96000046 [#1] PREEMPT SMP
Modules linked in:
CPU: 0 PID: 1592 Comm: bash Not tainted 4.7.0-rc1+ #1712
Hardware name: ARM Juno development board (r0) (DT)
task: ffffffc078fe0080 ti: ffffffc974178000 task.ti: ffffffc974178000
PC is at __memset+0x1ac/0x200
LR is at tmc_enable_etr_sink+0xf8/0x304
pc : [<ffffff80083a002c>] lr : [<ffffff800859be44>] pstate: 400001c5
sp : ffffffc97417bc00
x29: ffffffc97417bc00 x28: ffffffc974178000
Call trace:
Exception stack(0xffffffc97417ba40 to 0xffffffc97417bb60)
ba40: 0000000000000001 ffffffc974a5d098 ffffffc97417bc00 ffffff80083a002c
ba60: ffffffc974a5d118 0000000000000000 0000000000000000 0000000000000000
ba80: 0000000000000001 0000000000000000 ffffff800859bdec 0000000000000040
baa0: ffffff8008b45b58 00000000000001c0 ffffffc97417baf0 ffffff80080eddb4
bac0: 0000000000000003 ffffffc078fe0080 ffffffc078fe0960 ffffffc078fe0940
bae0: 0000000000000000 0000000000000000 00000000007fffc0 0000000000000004
bb00: 0000000000000000 0000000000000040 000000000000003f 0000000000000000
bb20: 0000000000000000 0000000000000000 0000000000000000 0000000000000001
bb40: ffffffc078fe0960 0000000000000018 ffffffffffffffff 0008669628000000
[<ffffff80083a002c>] __memset+0x1ac/0x200
[<ffffff8008599814>] coresight_enable_path+0xa8/0x1dc
[<ffffff8008599b10>] coresight_enable+0x88/0x1b8
[<ffffff8008599d88>] enable_source_store+0x3c/0x6c
[<ffffff800845eaf4>] dev_attr_store+0x18/0x28
[<ffffff80082829e8>] sysfs_kf_write+0x54/0x64
[<ffffff8008281c30>] kernfs_fop_write+0x148/0x1d8
[<ffffff8008200128>] __vfs_write+0x28/0x110
[<ffffff8008200e88>] vfs_write+0xa0/0x198
[<ffffff80082021b0>] SyS_write+0x44/0xa0
[<ffffff8008084e70>] el0_svc_naked+0x24/0x28
Code: 91010108 54ffff4a 8b040108 cb050042 (d50b7428)
This patch fixes the issue by clearing the drvdata->vaddr while we free
the allocated buffer at the end of a session, so that we allocate the
memory again.
Cc: mathieu.poirier@linaro.org
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
_coresight_build_path assumes that all the connections of a csdev
has the child_dev initialised. This may not be true if the particular
component is not supported by the kernel config(e.g TPIU) but is
present in the DT. In which case, building a path can cause a crash like this :
Unable to handle kernel NULL pointer dereference at virtual address 00000010
pgd = ffffffc9750dd000
[00000010] *pgd=00000009f5e90003, *pud=00000009f5e90003, *pmd=0000000000000000
Internal error: Oops: 96000006 [#1] PREEMPT SMP
Modules linked in:
CPU: 4 PID: 1348 Comm: bash Not tainted 4.6.0-next-20160517 #1646
Hardware name: ARM Juno development board (r0) (DT)
task: ffffffc97517a280 ti: ffffffc9762c4000 task.ti: ffffffc9762c4000
PC is at _coresight_build_path+0x18/0xe4
LR is at _coresight_build_path+0xc0/0xe4
pc : [<ffffff80083d5130>] lr : [<ffffff80083d51d8>] pstate: 20000145
sp : ffffffc9762c7ba0
[<ffffff80083d5130>] _coresight_build_path+0x18/0xe4
[<ffffff80083d51d8>] _coresight_build_path+0xc0/0xe4
[<ffffff80083d51d8>] _coresight_build_path+0xc0/0xe4
[<ffffff80083d51d8>] _coresight_build_path+0xc0/0xe4
[<ffffff80083d51d8>] _coresight_build_path+0xc0/0xe4
[<ffffff80083d51d8>] _coresight_build_path+0xc0/0xe4
[<ffffff80083d5cdc>] coresight_build_path+0x40/0x68
[<ffffff80083d5e14>] coresight_enable+0x74/0x1bc
[<ffffff80083d60a0>] enable_source_store+0x3c/0x6c
[<ffffff800830b17c>] dev_attr_store+0x18/0x28
[<ffffff80081ca9c4>] sysfs_kf_write+0x40/0x50
[<ffffff80081c9e38>] kernfs_fop_write+0x140/0x1cc
[<ffffff8008163ec8>] __vfs_write+0x28/0x110
[<ffffff8008164bf0>] vfs_write+0xa0/0x174
[<ffffff8008165d18>] SyS_write+0x44/0xa0
[<ffffff8008084e70>] el0_svc_naked+0x24/0x28
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following issue:
- In the extcon-palmas.c, fix the state of VBUS when using GPIO detection.
If probe funticon don't check the state during probe, the extcon client
driver cannot get the state of VBUS gpio until the user detach the connector
and attach the connector again.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXYU3FAAoJEJzN3yze689TVroP/0PRm1aIfZ15JgR07csngVXP
DR1gNPO6BkG2EVoAB6ZwgIVFLgDt3ylEOGfOY9av2ixwgiYQ2cuPQgQ8Lnqyiw5O
2TO5l0saG0E7rgQl04JX2qBT72CwbxyaJDV37++pOVeTBO/wSnQZ0iTOaFogJkPM
XjXt+VeQ0HR8WfIJE/TMzqbzcOMreAjuaMHkPSwttqZiUaA/qaThj0tClx7goKFW
vH2AgPWucSj7Azlr/oFtXeoqaTDJrYFpOoSCYTKm6Gx/GdumAcVEJe2s+siEA4Fo
d8R3fh4uUQD1ogsVmNeyznfw/EPL2wBfcoWs1qQOSaRoT1EI0bsmBFIuDdcUyvpq
XI4xIblVGJW/U66Riz34JNDdHtz0x31helXGQzYRGg94n5mdPMdmKTUnwphDEZ9u
6J1x2uFfTIUFpVV+1pDyvjeLvyEpaq2KrEfN224t+D9ak4K/dO1fcy9i448o3uI+
AJHihqMpE5Zn7QgpUox2P+plgAWblb39Ney3whJpFrGPZXS346iSFbyoEvAaiute
Bo1xjuLZ8llmY5WzFAU2zp5yfVuTn89x59WuvTWWGp05y84A/APM/4QfghX1FhdD
587ow14/vmX1kPwfDagMlOa+vXzV+GLk3tbM/GQfFxx9lGU71ryA/xwcTi/HB+vU
axCcfpn6fcGhD4X+UYSW
=62e3
-----END PGP SIGNATURE-----
Merge tag 'extcon-fixes-for-4.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon into char-misc-linus
Chanwoo writes:
Update extcon for v4.7-rc4
This patch fixes the following issue:
- In the extcon-palmas.c, fix the state of VBUS when using GPIO detection.
If probe funticon don't check the state during probe, the extcon client
driver cannot get the state of VBUS gpio until the user detach the connector
and attach the connector again.
Hayes Wang says:
====================
r8152: fix known issues
These patches fix some known issues.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The rx early size should be
(agg_buf_sz - packet size) / 8
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reset the BMU to clear the rx/tx fifo. This avoids that the unexpected
data remains in the hw.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable MAC clock speed down. It may casue the first control
transfer to contain the wrong data, when the power state change
from U1 to U0.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
bpf fixes
Fixes for two bpf bugs:
1st bug reported by Sasha Goldshtein here:
https://github.com/iovisor/bcc/issues/570
2nd discovered by Daniel Borkmann by manual code analysis.
See patches for details.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
similar to bpf_perf_event_output() the bpf_perf_event_read() helper
needs to check the type of the perf_event before reading the counter.
Fixes: a43eec3042 ("bpf: introduce bpf_perf_event_output() helper")
Reported-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ctx structure passed into bpf programs is different depending on bpf
program type. The verifier incorrectly marked ctx->data and ctx->data_end
access based on ctx offset only. That caused loads in tracing programs
int bpf_prog(struct pt_regs *ctx) { .. ctx->ax .. }
to be incorrectly marked as PTR_TO_PACKET which later caused verifier
to reject the program that was actually valid in tracing context.
Fix this by doing program type specific matching of ctx offsets.
Fixes: 969bf05eb3 ("bpf: direct packet access")
Reported-by: Sasha Goldshtein <goldshtn@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull drm fixes from Dave Airlie:
"The main drm fixes pull for rc4: one regression fix in the connector
refcounting, and an MST fix.
There rest is nouveau, amdkfd, i915, etnaviv, and radeon/amdgpu fixes,
mostly regression or black screen fixes"
* tag 'drm-fixes-for-v4.7-rc4' of git://people.freedesktop.org/~airlied/linux: (23 commits)
drm/etnaviv: initialize iommu domain page size
drm/nouveau/iccsense: fix memory leak
drm/nouveau/Revert "drm/nouveau/device/pci: set as non-CPU-coherent on ARM64"
drm/amd/powerplay: select samu dpm 0 as boot level on polaris.
drm/amd/powerplay: update powerplay table parsing
drm/dp/mst: Always clear proposed vcpi table for port.
drm/crtc: only store the necessary data for set_config rollback
drm/crtc: fix connector reference counting mismatch in drm_crtc_helper_set_config
drm/i915/ilk: Don't disable SSC source if it's in use
Revert "drm/amdgpu: add pipeline sync while vmid switch in same ctx"
drm/amdgpu/gfx7: fix broken condition check
drm/radeon: fix asic initialization for virtualized environments
amdgpu: fix asic initialization for virtualized environments (v2)
drm/radeon: don't use fractional dividers on RS[78]80 if SS is enabled
drm/radeon: do not hard reset GPU while freezing on r600/r700 family
drm/i915: Extract physical display dimensions from VBT
drm/i915: Check VBT for port presence in addition to the strap on VLV/CHV
drm/i915: Only ignore eDP ports that are connected
drm/i915: Silence "unexpected child device config size" for VBT on 845g
drm/i915: Fix NULL pointer deference when out of PLLs in IVB
...
Minor kconfig dependency cleanup, trivial mic mute hotkey for ideapad, and a
needed improvement in adaptive keyboard detection for thinkpad.
platform/x86:
- Drop duplicate dependencies on X86
thinkpad_acpi:
- Add support for HKEY version 0x200
ideapad_laptop:
- Add an event for mic mute hotkey
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXYhSbAAoJEKbMaAwKp364PPUIAJlE0nJqKdR8YbzVDvBrfhKb
onyvO3zRq+6TNKtAWQpJ70dBzto8IYbocu8zqEjRgH1o22xbKgs1p/qgKjZ5MTWr
z4qao91+yRPb8KIeQUL49R7DvngJeGqBTGkUK5j7jC2zF1/bQCfsN+UKdstWCLOR
rWt82M/Mz2Qm1PoawUkEa7ER8uuVvkh6rswLinOBPQKBDlqX3HnWACN+oRUZgKr5
34Wk31eZ9EMKufN9G4EP1IsS5pL8mbgIY6Tm6E4AuGRfgVooHST8wlPunSw8Ello
ud/0GsoP2UiGuUXb3CO8VYCA0zqw+kd1bP6Ff5LBzuCC05GqmvoByKF31cNzPo4=
=zqxG
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v4.7-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform driver fixes from Darren Hart:
"Minor kconfig dependency cleanup, trivial mic mute hotkey for ideapad,
and a needed improvement in adaptive keyboard detection for thinkpad:
platform/x86:
- Drop duplicate dependencies on X86
thinkpad_acpi:
- Add support for HKEY version 0x200
ideapad_laptop:
- Add an event for mic mute hotkey"
* tag 'platform-drivers-x86-v4.7-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
platform/x86: Drop duplicate dependencies on X86
thinkpad_acpi: Add support for HKEY version 0x200
ideapad_laptop: Add an event for mic mute hotkey
1) gre_parse_header() can be called from gre_err()
At this point transport header points to ICMP header, not the inner
header.
2) We can not really change transport header as ipgre_err() will later
assume transport header still points to ICMP header (using icmp_hdr())
3) pskb_may_pull() logic in gre_parse_header() really works
if we are interested at zone pointed by skb->data
4) As Jiri explained in commit b7f8fe251e ("gre: do not pull header in
ICMP error processing") we should not pull headers in error handler.
So this fix :
A) changes gre_parse_header() to use skb->data instead of
skb_transport_header()
B) Adds a nhs parameter to gre_parse_header() so that we can skip the
not pulled IP header from error path.
This offset is 0 for normal receive path.
C) remove obsolete IPV6 includes
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tom Herbert <tom@herbertland.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The implementation of net_dbg_ratelimited in the CONFIG_DYNAMIC_DEBUG
case was added with 2c94b5373 ("net: Implement net_dbg_ratelimited() for
CONFIG_DYNAMIC_DEBUG case"). The implementation strategy was to take the
usual definition of the dynamic_pr_debug macro, but alter it by adding a
call to "net_ratelimit()" in the if statement. This is, in fact, the
correct approach.
However, while doing this, the author of the commit forgot to surround
fmt by pr_fmt, resulting in unprefixed log messages appearing in the
console. So, this commit adds back the pr_fmt(fmt) invocation, making
net_dbg_ratelimited properly consistent across DEBUG, no DEBUG, and
DYNAMIC_DEBUG cases, and bringing parity with the behavior of
dynamic_pr_debug as well.
Fixes: 2c94b5373 ("net: Implement net_dbg_ratelimited() for CONFIG_DYNAMIC_DEBUG case")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Tim Bingham <tbingham@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skfp driver has been moved to drivers/net/fddi/skfp a long time
ago, but we still attempt to include headers from the old location,
which causes a warning when building with W=1:
cc1: error: /git/arm-soc/drivers/net/skfp: No such file or directory [-Werror=missing-include-dirs]
cc1: error: drivers/net/skfp: No such file or directory [-Werror=missing-include-dirs]
Clearly this include directive is not needed any more, so we can
just remove it now.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/tipc/link.c: In function ‘tipc_link_timeout’:
net/tipc/link.c:744:28: warning: ‘mtyp’ may be used uninitialized in this function [-Wuninitialized]
Fixes: 42b18f605f ("tipc: refactor function tipc_link_timeout()")
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=yLxu
-----END PGP SIGNATURE-----
Merge tag 'upstream-4.7-rc4' of git://git.infradead.org/linux-ubifs
Pull UBI fixes from Richard Weinberger:
"This contains fixes for a regression introduced in rc1"
* tag 'upstream-4.7-rc4' of git://git.infradead.org/linux-ubifs:
ubi: Don't bypass ->getattr()
Revert "mtd: switch open_mtd_by_chdev() to use of vfs_stat()"
Revert "mtd: switch ubi_open_volume_path() to vfs_stat()"
Modules which register drivers via standard path (driver_register) in
parallel can cause a warning:
WARNING: CPU: 2 PID: 3492 at ../fs/sysfs/dir.c:31 sysfs_warn_dup+0x62/0x80
sysfs: cannot create duplicate filename '/module/saa7146/drivers'
Modules linked in: hexium_gemini(+) mxb(+) ...
...
Call Trace:
...
[<ffffffff812e63a2>] sysfs_warn_dup+0x62/0x80
[<ffffffff812e6487>] sysfs_create_dir_ns+0x77/0x90
[<ffffffff8140f2c4>] kobject_add_internal+0xb4/0x340
[<ffffffff8140f5b8>] kobject_add+0x68/0xb0
[<ffffffff8140f631>] kobject_create_and_add+0x31/0x70
[<ffffffff8157a703>] module_add_driver+0xc3/0xd0
[<ffffffff8155e5d4>] bus_add_driver+0x154/0x280
[<ffffffff815604c0>] driver_register+0x60/0xe0
[<ffffffff8145bed0>] __pci_register_driver+0x60/0x70
[<ffffffffa0273e14>] saa7146_register_extension+0x64/0x90 [saa7146]
[<ffffffffa0033011>] hexium_init_module+0x11/0x1000 [hexium_gemini]
...
As can be (mostly) seen, driver_register causes this call sequence:
-> bus_add_driver
-> module_add_driver
-> module_create_drivers_dir
The last one creates "drivers" directory in /sys/module/<...>. When
this is done in parallel, the directory is attempted to be created
twice at the same time.
This can be easily reproduced by loading mxb and hexium_gemini in
parallel:
while :; do
modprobe mxb &
modprobe hexium_gemini
wait
rmmod mxb hexium_gemini saa7146_vv saa7146
done
saa7146 calls pci_register_driver for both mxb and hexium_gemini,
which means /sys/module/saa7146/drivers is to be created for both of
them.
Fix this by a new mutex in module_create_drivers_dir which makes the
test-and-create "drivers" dir atomic.
I inverted the condition and removed 'return' to avoid multiple
unlocks or a goto.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Fixes: fe480a2675 (Modules: only add drivers/ direcory if needed)
Cc: v2.6.21+ <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
