* make eeprom size a variable, prepping for future patch
* eliminate unused PCI_xxx stuff left over from Becker driver template
* convert a few #defines to enum
* mark PCI table const, __devinitdata
* don't bother with named constant for PCI device id
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Updates generic HDLC info page address, I should have done it
long time ago.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
dev_setup() is using the __initdata variables ax25_broadcast and
ax25_test.
Since the only caller of dev_setup() (setup_adapter()) is already
__init, the solution is to make dev_setup() __init, too.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
From: Uwe Zeisberger <Uwe_Zeisberger@digi.com>
The phy ids used are taken from an driver that used a right shift of 4 to chop
off the revision number. This driver does not shift, so the id and mask
values are wrong and must be left shifted by 4 to actually detect the chips.
Signed-off-by: Uwe Zeisberger <Uwe_Zeisberger@digi.com>
Acked-by: Andy Fleming <afleming@freescale.com>
[akpm: this is a previously-nacked patch, but the problem is real]
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Ensure the driver's module owner field is
initialised for when this is being built and
loaded as a module.
Also change make the dm9000_tx_done function
static, as it is not exported elsewhere.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The DM9000 initialisation sequence for the
hardware re-initialise the board spin-lock,
which is in my view wrong.
This patch removes the extra spin lock
initialisation
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The DM9000 driver does not deal with the case
where there is no serial EEPROM to store the
configuration, and the bootloader has placed
an MAC address into the device already.
If there is no valid MAC in the EEPROM, read
the one already in the chip and check to see
if that one is valid.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The current DM9000 driver cannot cope if it
is given more than 3 resources (for example, if
it is being passed an wake-up irq that it is
not using yet).
Check that we have been given at-least one IRQ
resource.
Also fix the minor type-casting for the case
of 2 resources.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Ata_piix's Kconfig entry still refers only to ICH5, while it supports ICH6
through 8. This creates confusion with people who are looking to see
if their newer SATA enabled motherboards are supported. The
following patch makes this clear.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some SATA controllers embedded in ATI IXPs seem to have broken
SATA_IRQ bit in their bmdma2 registers which is always stuck at 1.
This makes the driver believe that there has been a hotplug event and
freeze the port whenever there's an interrupt thus failing all
commands.
This patch disables SATA_IRQ for those controllers.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Cosmetic updates in libata-core.c.
* trim trailing whitespaces
* break lines which are over 80 column
* kill unnecessary braces
* make indentation consistent
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
From: Andrew Morton <akpm@osdl.org>
Provide a module parameter to override the default 30-second-per-device SATA
probing timeout.
Cc: Tejun Heo <htejun@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make ata_do_simple_cmd() and ata_flush_cache() global. These will be
used from libata-eh.c.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* the function has always returned AC_ERR_* masks not -errno but its
return type was int. Make return type unsigned int.
* don't print error message automatically. it's the caller's
responsibility.
* add header comment
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Clear related EH action on device detach such that new device doesn't
receive EH actions scheduled for the old one.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement and use ata_eh_dev_action() which returns EH action mask for
a device.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Partially revert 74d0a988d3:
[PATCH] PCI: Move various PCI IDs to header file
libata policy is to avoid use of named PCI device ID constants.
These are often single-use constants, which have little value over
direct numeric constants save for constant include/linux/pci_ids.h
patching/merging headaches.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- DMA CSR register is cleared by reading on omap1, but on
omap2 it is cleard by writing to it.
- DMA TOUT interrupt does not exist on omap24xx, rename it
- Add SECURE and MISALIGNED errors by default for omap24xx
- Add defines for external DMA request lines
Signed-off-by: Tony Lindgren <tony@atomide.com>
This may seem like a DILLIGAF, but after chatting with the F/W folks,
there is no harm in dropping the page calculation as denoted in the
enclosed patch for these older adapters in this new age of 4GB+ memory
sticks. Any resource optimization within the old-old-old adapters for
systems with less than 4G of memory is of little consequence. The
existing AAC_QUIRK_31BIT flag in linit.c should look after the rest of
the legacy hardware DMA limitations.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The scsi layer is already calling add_disk_randomness in scsi_end_request.
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We currently stuff a truncated size into the geometry logic and return the
result which can produce bizarre reports for a 4Tb array. Since that
mapping logic isn't useful for disks that big don't try and map this way at
all.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: Randy Dunlap <rdunlap@xenotime.net>
Fix sparse warnings: use NULL instead of 0 for pointers:
drivers/scsi/lpfc/lpfc_els.c:827:56: warning: Using plain integer as NULL pointer
drivers/scsi/lpfc/lpfc_els.c:2781:18: warning: Using plain integer as NULL pointer
drivers/scsi/lpfc/lpfc_els.c:2782:18: warning: Using plain integer as NULL pointer
drivers/scsi/lpfc/lpfc_init.c:951:21: warning: Using plain integer as NULL pointer
drivers/scsi/lpfc/lpfc_init.c:956:20: warning: Using plain integer as NULL pointer
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Acked-by: James Smart <James.Smart@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Original code incorrectly assigned it to the driver's
link-down-timeout value (a value in seconds).
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Also remove qla2xxx_probe_one/qla2xxx_remove_one stubs previously
used with external firmware module loaders.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
As there is no point in failing the initialization process when
firmware informs the host software that it could not transition
beyond a CONFIG_WAIT nor WAIT_FOR_LOGIN state. Previous logic
would mark such conditions as a general *failure* and subsequently
tear-down the scsi-host during initialization.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Similar in form to QLogic's standard offering -- via
the 'extended_error_logging' module parameter.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- macro usage statements should terminate with a ';'
- remove unused macros.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The host section of ISP24xx NVRAMs contain a new bit which
allows a user to selectively disable ports of an HBA. These
ports (hosts) will not be presented to the midlayer.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Defer firmware dump-data raw-to-textual conversion to
user-space.
- Add module parameter (ql2xallocfwdump) to allow for per-HBA
allocations of firmware dump memory.
- Dump request and response queue data as per firmware group
request.
- Add extended firmware trace support for ISP24XX/ISP54XX chips.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Mark Bellon found a bug in my tlclk driver. Thanks!
I botch the register mask for store_received_ref_clk3a.
See http://download.intel.com/design/network/manuals/30412001.pdf
tables 124 and 136 for details.
Signed-off-by: Mark Gross <mark.gross@intel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial:
typo fixes
Clean up 'inline is not at beginning' warnings for usb storage
Storage class should be first
i386: Trivial typo fixes
ixj: make ixj_set_tone_off() static
spelling fixes
fix paniced->panicked typos
Spelling fixes for Documentation/atomic_ops.txt
move acknowledgment for Mark Adler to CREDITS
remove the bouncing email address of David Campbell
The changes in the tty handling contain a bug while accessing
the last byte in the skb. Since special sequence for control of
DTMF and FAX via ttyI* devices handled via this path, these services
do not work anymore.
Signed-off-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I've always found this flag confusing. Now that devfs is no longer around, it
has been renamed, and the documentation for when this flag should be used has
been updated.
Also fixes all drivers that use this flag.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
