Move link test call to later in the offline sequence, move the
restore settings block to afterwards and add another reset to ensure
the hardware is in a known state afterwards.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Power Management Quality of Service is not supported or used by the VF
driver.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are currently some problems with igb.
- On 32bit arches, maintaining 64bit counters without proper
synchronization between writers and readers.
- Stats updated every two seconds, as reported by Jesper.
(Jesper provided a patch for this)
- Potential problem between worker thread and ethtool -S
This patch uses u64_stats_sync, and convert everything to be 64bit safe,
SMP safe, even on 32bit arches. It integrates Jesper idea of providing
accurate stats at the time user reads them.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even though the parent is recorded with the normal function tracing
of the latency tracers (irqsoff and wakeup), the function graph
recording is bogus.
This is due to the function graph messing with the return stack.
The latency tracers pass in as the parent CALLER_ADDR0, which
works fine for plain function tracing. But this causes bogus output
with the graph tracer:
3) <idle>-0 | d.s3. 0.000 us | return_to_handler();
3) <idle>-0 | d.s3. 0.000 us | _raw_spin_unlock_irqrestore();
3) <idle>-0 | d.s3. 0.000 us | return_to_handler();
3) <idle>-0 | d.s3. 0.000 us | trace_hardirqs_on();
The "return_to_handle()" call is the trampoline of the
function graph tracer, and is meaningless in this context.
Cc: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The preempt and irqsoff tracers have three types of function tracers.
Normal function tracer, function graph entry, and function graph return.
Each of these use a complex dance to prevent recursion and whether
to trace the data or not (depending if interrupts are enabled or not).
This patch moves the duplicate code into a single routine, to
prevent future mistakes with modifying duplicate complex code.
Cc: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The wakeup tracer has three types of function tracers. Normal
function tracer, function graph entry, and function graph return.
Each of these use a complex dance to prevent recursion and whether
to trace the data or not (depending on the wake_task variable).
This patch moves the duplicate code into a single routine, to
prevent future mistakes with modifying duplicate complex code.
Cc: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Add function graph support for wakeup latency tracer.
The graph output is enabled by setting the 'display-graph'
trace option.
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
LKML-Reference: <1285243253-7372-4-git-send-email-jolsa@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Move trace_graph_function() and print_graph_headers_flags() functions
to the trace_function_graph.c to be globaly available.
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
LKML-Reference: <1285243253-7372-3-git-send-email-jolsa@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The check_irq_entry and check_irq_return could be called
from graph event context. In such case there's no graph
private data allocated. Adding checks to handle this case.
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
LKML-Reference: <20100924154102.GB1818@jolsa.brq.redhat.com>
[ Fixed some grammar in the comments ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
HW workaround:
Disable logging of correctable error for some NX3031 based adapter.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is race between netif_stop_queue and netif_stopped_queue
check.So check once again if buffers are available to avoid race.
With above logic we can also get rid of tx lock in process_cmd_ring.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added statistics for Nic Partition supported adapter.
These statistics are maintined in device.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change a few checks against the hardcoded broadcast address,
0xffffffff, to ipv4_is_lbcast(). Remove some existing checks
using ipv4_is_lbcast() that are now obviously superfluous.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As suggested by: Joe Perches <joe@perches.com>
Although RSS is meaningless when there is a single HW queue we
still need it enabled in order to have HW Rx hash generated.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
the value of the constant is the same, but it's clearer to use original
constant provided by HSI
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Optimized the branching in the bnx2x_rx_int() based on the fact
that FP CQE will always have at least one of START or STOP flags set,
so if not both bits are set and START bit is not set,
then it's a STOP bit that is set.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit e446630c96, i.e. v2.6.35-rc1,
the mcp251x chip model can be selected via the modalias member in the
struct spi_board_info. The driver stores the actual model in the
struct mcp251x_platform_data.
From the driver point of view the platform_data should be read only.
Since all in-tree users of the mcp251x have already been converted to
the modalias method, this patch moves the "model" member from the
struct mcp251x_platform_data to the driver's private data structure.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Christian Pellegrin <chripell@fsfe.org>
Cc: Marc Zyngier <maz@misterjones.org>
This shuffles the clock framework code around to a drivers/sh/clk subdir,
to follow the intc split up. This will make it easier to subsequently
break things out as well as plug in different helpers for non-CPG users.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The end condition of for_each_frequency should care about
both clk_rate_table_round and clk_rate_div_range_round,
and using "correct max size" is a natural idea in later function.
To avoid data over flow, this patch didn't modify
clk_rate_div_range_round side as .max = div_max + 1.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
clk_get() returns an ERR_PTR(errno) on error and not NULL.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds header <linux/sched.h> into the below files for build with
CONFIG_PREEMPT_NONE.
arch/arm/mach-s5p64x0/cpu.c
Signed-off-by: Seung-Chull Suh <sc.suh@samsung.com>
[kgene.kim@samsung.com: edited title and message]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The patch removes s3c_gpio_lock/unlock to avoid acquiring the lock
recursively as lock is already acquired by calling function.
Signed-off-by: Atul Dahiya <atul.dahiya@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
[kgene.kim@samsung.com: removed useless variable due to this]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The s5p64x0_sysclass should be used in place of the obselete s5p6440_sysclass.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Fix the touch screen device name from s3c64x0-adc to s3c64xx-adc.
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch updates s5p64x0_defconfig and changes the name from
s5p6440_defconfig so that can support S5P6440 and S5P6450 with
one kernel.
Tested on SMDK6440(S5P6440) and SMDK6450(S5P6450).
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds UART serial port support for S5P6450 SoC.
The S5P6450 has 6 UARTs, so adds resource of UART4 and UART5.
And to fix membase which is in serial/samsung.c is from Ben Dooks.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
This patch moves smdk6440 board file from mach-s5p6440 into the new
mach-s5p64x0 directory and adds smdk6450 board file.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch moves S5P6440 GPIO support files from mach-s5p6440
into the new mach-s5p64x0 for merge S5P6440 and S5P6450 SocS.
NOTE: Not supported S5P6450 GPIO yet. Will be supported soon.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds S5P6450 I2C support in the ARCH_S5P64X0. And
moves S5P6440 I2C support files into the mach-s5p64x0 together.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch moves DMA support files in the mach-s5p64x0
for S5P6440 and S5P6450 SoCs.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Jassi Brar <jassi.brar@samsung.com>
This patch updates Audio and SPI for S5P6440 and S5P6450 SoCs.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Jassi Brar <jassi.brar@samsung.com>
This patch updates regarding clock files for supporting S5P6440 and
S5P6450 with one kernel image. The mach-s5p64x0/clock.c is for common
of them and there are specific clock files for each SoCs.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds ARCH_S5P64X0 which can support S5P6440 and S5P6450 with
one kernel image. So moved some files of mach-s5p6440 into the new ARCH
directory mach-s5p64x0.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The ebt_ip6.h and ebt_nflog.h headers are not not known to Kbuild and
therefore not installed by make headers_install. Fix that up.
Signed-off-by: Nick Bowler <nbowler@elliptictech.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch introduces a variable "clear_intf" that hold the bits that
should be cleared. Only read-modify-write register if "clear_intf"
is set.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Use read-modify-write instead of a simple write to change the register
contents, to close existing the race window between the original manual
read and write.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
This patch bases on work done earlier by David Jander.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: David Jander <david@protonic.nl>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
This patch replaces netif_rx() with netif_rx_ni() which has to be used
from the threaded interrupt i.e. process context context.
Thanks to Christian Pellegrin for pointing at the right fix:
481a819914 by Oliver Hartkopp.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
