Some 82599 adapters contain thermal data that we can get to via
an i2c interface. These functions provide support to get at that
data. A following patch will export this data.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Secondary unicast and multicast addresses are added to the Receive
Address registers (RAR) for most parts supported by the driver. For
82579, there is only one actual RAR and a number of Shared Receive Address
registers (SHRAR) that are shared among the driver and f/w which can be
reserved and write-protected by the f/w. On this device, use the SHRARs
that are not taken by f/w for the additional addresses.
Add a MAC ops function pointer infrastructure (similar to other MAC
operations in the driver) for setting RARs, introduce a new rar_set
function for 82579 and convert the existing code that sets RARs on other
devices to a generic rar_set function.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The PHY initialization flows and assorted workarounds for 82577/8/9 done
during driver load and resume from Sx should be the same yet they are not.
Combine the current flows/workarounds into a common set of functions that
are called during the different code paths.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
An update to the EEPROM on 82579 will extend a delay in hardware to fix an
issue with WoL not working after a G3->S5 transition which is unrelated to
the driver. However, this extended delay conflicts with nominal operation
of the device when it is initialized by the driver and after every reset
of the hardware (i.e. the driver starts configuring the device before the
hardware is done with it's own configuration work). The workaround for
when the driver is in control of the device is to tell the hardware after
every reset the configuration delay should be the original shorter one.
Some pre-existing variables are renamed generically to be re-used with
new register accesses.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bug: The VLAN bit of the MAC RX Status Word is unreliable in several older
supported chips. Sometimes the VLAN bit is not set for valid VLAN packets
and also sometimes the VLAN bit is set for non-VLAN packets that came after
a VLAN packet. This results in a receive length error when VLAN hardware
tagging is enabled.
Fix: Variation on original fix proposed by Mirko.
The VLAN information is decoded in the status loop, and can be
applied to the received SKB there. This eliminates the need for the
separate tag field in the interface data structure. The tag has to
be copied and cleared if packet is copied. This version checked out
with vlan and normal traffic.
Note: vlan_tx_tag_present should be renamed vlan_tag_present, but that
is outside scope of this.
Reported-by: Mirko Lindner <mlindner@marvell.com>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a small packet is received, the driver copies it to a new skb to allow
reusing the full size Rx buffer. The copy was propogating the checksum offload
but not the receive hash information. The bug is impact was mostly harmless
and therefore not observed until reviewing this area of code.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver calls cxgb_vlan_mode() from init_one(). This calls into
synchronize_rx(), which locks all the q locks, but the q locks are not
initialized until cxgb_up() -> setup_sge_qsets(). So move the call to
cxgb_vlan_mode() into cxgb_up(), after the call to setup_sge_qsets().
We also move the body of these functions up higher to avoid having to
a forward declaration.
This was found because of the lockdep warning:
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
Pid: 323, comm: work_for_cpu Not tainted 3.4.0-rc5 #28
Call Trace:
[<ffffffff8106e767>] register_lock_class+0x108/0x2d0
[<ffffffff8106ff42>] __lock_acquire+0xd3/0xd06
[<ffffffff81070fd0>] lock_acquire+0xbf/0xfe
[<ffffffff813862a6>] _raw_spin_lock_irq+0x36/0x45
[<ffffffffa01e71aa>] cxgb_vlan_mode+0x96/0xcb [cxgb3]
[<ffffffffa01f90eb>] init_one+0x8c4/0x980 [cxgb3]
[<ffffffff811fcbf0>] local_pci_probe+0x3f/0x70
[<ffffffff81042206>] do_work_for_cpu+0x10/0x22
[<ffffffff810482de>] kthread+0xa1/0xa9
[<ffffffff8138e234>] kernel_thread_helper+0x4/0x10
Contrary to what lockdep says, the code is not fine: we are locking an
uninitialized spinlock.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the support to bounce buffer added, the skb is coming as nonlinear in the
case of non-DDPed data frames for FCoE, which is mostly ok as the FCoE stack
would take care of that. However, for target mode, we have to set the FC CRC
and FC EOF field to allow the protocol stack to not drop the frame for the last
data frame of that sequence. So fix this by linearizing the skb first before
doing skb_put().
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Marcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was freeing memory in shutdown instead of remove. As a result
we were leaking memory if IEEE DCB was enabled and we loaded/unloaded the
driver. This change moves the freeing of the memory into the remove
routine where it belongs.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Maybe it's a typo, but it cause that igbvf can't be initialized successfully.
Set perm_addr value using valid dev_addr, although which is equal to hw.mac.addr.
Signed-off-by: Samuel Liao <samuelliao@tencent.com>
Signed-off-by: Shan Wei <davidshan@tencent.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
PHY polling code for FPGA is considered in every MDIO R/W API.
no need to add additional code to atl1c_change_mtu.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: David Liu <dwliu@qca.qaulcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
L0S might be unstable if no cable link, only enable it when link up.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There may be tx-skbs still pending in HW when PHY link down.
Reset MAC will make the DMA engine go to the start point.
and release all pending skbs.
Note: Reset MAC will clear any interrupt status and mask.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
common_task might be running while close routine is called,
wait/cancel it.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware incorrectly process L0S/L1 entrance if the chipset/root
response after specific/shorter timer and cause system hang.
Enlarge the timeout value to avoid this issue.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some platform with EEPROM/OTP existing, the BIOS could overwrite
a new MAC address for the NIC. so, the permanent mac address should
be from BIOS. the address is restored when driver removing.
Voltage raising isn't applicable for l1d.
Replace swab32 with htonl for big/little endian platform.
related Registers are refined as well.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Close-action is done by atl1c_reset_pcie, remove it from
atl1c_get_permanent_address.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
WoL status is read-clear and should be cleared when in S0
status.
putting it in atl1c_reset_pcie is more suitable than
in atl1c_get_permanent_address.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some platforms the PHY settings need to change depending on the
cable link status to get better stability.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before doing skb->head_frag work on bnx2x driver, I found too much stuff
was inlined in bnx2x/bnx2x_cmn.h for no good reason and made my work not
very easy.
Move some big functions out of this include file to the respective .c
file.
A lot of inline keywords are not needed at all in this huge driver.
text data bss dec hex filename
490083 1270 56 491409 77f91 bnx2x/bnx2x.ko.before
484206 1270 56 485532 7689c bnx2x/bnx2x.ko
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Matt Carlson <mcarlson@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reset logic after a Rx FIFO overrun will clear the programmed
multicast addresses. This patch fixes the issue by reprogramming the
registers after the reset.
The commit eefc48b ("pch_gbe: reprogram multicast address register on
reset") tried to fix this problem, but it introduces unnecessary
codes. In fact, all multicast addresses have been saved in netdev->mc,
So we can call pch_gbe_set_multi() directly after reset_hw and
reset_rx.
This commit kills 50+ line codes
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Takahiro Shimizu <tshimizu818@gmail.com>
Signed-off-by: RongQing.Li <roy.qing.li@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts tg3 driver, one of our reference drivers, to use new
build_skb() api in frag mode.
Instead of using kmalloc() to allocate the memory block that will be
used by build_skb() as skb->head, we use a page fragment.
This is a followup of patch "net: allow skb->head to be a page fragment"
This allows GRO, TCP coalescing, and splice() to be more efficient.
Incidentally, this also removes SLUB slow path contention in kfree()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Matt Carlson <mcarlson@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->head is currently allocated from kmalloc(). This is convenient but
has the drawback the data cannot be converted to a page fragment if
needed.
We have three spots were it hurts :
1) GRO aggregation
When a linear skb must be appended to another skb, GRO uses the
frag_list fallback, very inefficient since we keep all struct sk_buff
around. So drivers enabling GRO but delivering linear skbs to network
stack aren't enabling full GRO power.
2) splice(socket -> pipe).
We must copy the linear part to a page fragment.
This kind of defeats splice() purpose (zero copy claim)
3) TCP coalescing.
Recently introduced, this permits to group several contiguous segments
into a single skb. This shortens queue lengths and save kernel memory,
and greatly reduce probabilities of TCP collapses. This coalescing
doesnt work on linear skbs (or we would need to copy data, this would be
too slow)
Given all these issues, the following patch introduces the possibility
of having skb->head be a fragment in itself. We use a new skb flag,
skb->head_frag to carry this information.
build_skb() is changed to accept a frag_size argument. Drivers willing
to provide a page fragment instead of kmalloc() data will set a non zero
value, set to the fragment size.
Then, on situations we need to convert the skb head to a frag in itself,
we can check if skb->head_frag is set and avoid the copies or various
fallbacks we have.
This means drivers currently using frags could be updated to avoid the
current skb->head allocation and reduce their memory footprint (aka skb
truesize). (thats 512 or 1024 bytes saved per skb). This also makes
bpf/netfilter faster since the 'first frag' will be part of skb linear
part, no need to copy data.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Matt Carlson <mcarlson@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Insert an skb_tx_timestamp call in both ndo_start_xmit routines
Tested to work for the nv_start_xmit_optimized case
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
release_firmware() checks for NULL pointers - no need to test before
the call.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Since release_firmware() deals gracefully with being passed a NULL
pointer there is no reason to test explicitly before calling the
function.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
release_firmware() does its own NULL test so explicit test before call
is unneeded.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There is no need to test for a NULL pointer before calling
release_firmware - the function does that on its own.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There's no need to test for a NULL pointer before calling
release_firmware() since the function does that check itself, so
remove the redundant test.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: David Dillow <dave@thedillows.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If I understand correct, NETIF_F_IP_CSUM only means the hardware
will compute the TCP/UDP checksum, IP checksum is always computed
in software
So as a workround of hardware unable to compute small packages
checksum, do not need to compute IP header checksum.
Signed-off-by: RongQing.Li <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCH_GBE_ETH_ALEN is equal to ETH_ALEN, so we can replace it with
ETH_ALEN.
If they are not equal, it must be a bug, since this is ethernet,
and the address has been already stored to mc_addr_list as ETH_ALEN
bytes when call pch_gbe_mac_mc_addr_list_update.
Signed-off-by: RongQing.Li <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the gpio_to_irq() function to retrieve the phy IRQ line
from the GPIO pin specification.
This fix is needed now that we have moved to irqdomains on AT91.
Reported-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
The AT91RM9200 Ethernet controller still has a fixed IO mapping.
So:
* Remove the fixed IO mapping and AT91_VA_BASE_EMAC definition.
* Pass the physical base-address via platform-resources to the driver.
* Convert at91_ether.c driver to perform an ioremap().
* Ethernet PHY detection needs to be performed during the driver
initialization process, it can no longer be done first.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch consolidates the case logic for checking whether a device supports
WoL into a single place. Previously ethtool and probe used similar logic that
was copied and maintained separately. This patch encapsulates the core logic
into a function so that a user only has to update one place.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
During igb_reset(), we initiate a hardware reset which will clear our
flow control settings. For auto-negotiation, we re-negotiate them when
linking up again, but we need to force them off properly for the forced
speed case.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously, a workaround was added to address a hardware bug in the
PCIm2PCI arbiter where a write by the driver of the Transmit/Receive
Descriptor Tail register could happen concurrently with a write of any
MAC CSR register by the Manageability Engine (ME) which could cause the
Tail register to have an incorrect value. The arbiter is supposed to
prevent the concurrent writes but there is a bug that can cause the Host
(driver) access to be acknowledged later than it should.
After further investigation, it was discovered that a driver write access
of any MAC CSR register after being idle for some time can be lost when
ME is accessing a MAC CSR register. When this happens, no further target
access is claimed by the MAC which could hang the system.
The workaround to check bit 24 in the FWSM register (set only when ME is
accessing a MAC CSR register) and delay for a limited amount of time until
it is cleared is now done for all driver writes of MAC CSR registers on
82579 with ME enabled. In the rare case when the driver is writing the
Tail register and ME is accessing any MAC CSR register for a duration
longer than the maximum delay, write the register and verify it has the
correct value before continuing, otherwise reset the device.
This patch also moves some pre-existing macros from the hardware-specific
header file to the more appropriate generic driver header file.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In K1 mode (a MAC/PHY interconnect power mode), the 82579 device shuts down
the Phase Lock Loop (PLL) of the interconnect to save power. When the PLL
starts working, the 82579 device may start to transfer the packet through
the interconnect before it is fully functional causing packet drops. This
workaround disables shutting down the PLL in K1 mode for 1G link speed.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Performance testing has shown that enabling DMA burst on 82574
improves performance on small packets, so enable it by default.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
80003ES2LAN has an errata such that far-end loopback may be activated by
bit errors producing a reserved symbol. In order to disable far-end
loopback quickly enough, disable it immediately following a reset.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
logical speed returned by link_status_query needs to be multiplied by 10.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o 0x3, 0x7, 0xF, 0x1F, 0x3F, 0x7F and 0xFF are the allowed capture masks.
o Updated driver version to 5.0.28
Signed-off-by: Manish chopra <manish.chopra@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Without failing probe, register netdevice when device is in FAILED state.
o Device will come up with minimum functionality.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dl2k driver's rio_ioctl call has a few issues:
- No permissions checking
- Implements SIOCGMIIREG and SIOCGMIIREG using the SIOCDEVPRIVATE numbers
- Has a few ioctls that may have been used for debugging at one point
but have no place in the kernel proper.
This patch removes all but the MII ioctls, renumbers them to use the
standard ones, and adds the proper permission check for SIOCSMIIREG.
We can also get rid of the dl2k-specific struct mii_data in favor of
the generic struct mii_ioctl_data.
Since we have the phyid on hand, we can add the SIOCGMIIPHY ioctl too.
Most of the MII code for the driver could probably be converted to use
the generic MII library but I don't have a device to test the results.
Reported-by: Stephan Mueller <stephan.mueller@atsec.com>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
