Fengguang reports that the xHCI driver isn't linked properly on his
machine:
ERROR: "__udivdi3" [drivers/usb/host/xhci-hcd.ko] undefined!
ERROR: "handle_edge_irq" [drivers/gpio/gpio-pch.ko] undefined!
ERROR: "irq_to_desc" [drivers/gpio/gpio-pch.ko] undefined!
The driver compiles fine on my 64-bit box (gcc version 4.6.1).
Fengguang thinks it's because the xHCI driver was using DIV_ROUND_UP()
instead of DIV_ROUND_UP_ULL() with arguments that were unsigned long
long variables.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Wu Fengguang <wfg@linux.intel.com>
The USB 2.0 Link PM code is conditionally compiled when
CONFIG_USB_SUSPEND=y. I believe that's a mistake, since Link PM is not
directly related to USB device suspend and Link PM is implemented
without relying on any of the suspend code in the USB core. For now,
keep the USB 2.0 Link PM code conditionally compiled if
CONFIG_USB_SUSPEND=y.
This patch does move the code to implement USB 3.0 Link PM out of the
xHCI driver #ifdefs for CONFIG_USB_SUSPEND and moves it into a section
dependent on CONFIG_PM. The USB core functions for USB 3.0 Link PM are
already conditionally compiled when CONFIG_PM=y.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
When CONFIG_PM=n, make sure that the usb_[unlocked_][en/dis]able_lpm
declarations are visible in include/linux/usb.h, and exported from
drivers/usb/core/hub.c.
Before this patch, if CONFIG_USB_SUSPEND was turned off, it would cause
build errors:
drivers/usb/core/hub.c: In function 'usb_disable_lpm':
drivers/usb/core/hub.c:3394:2: error: implicit declaration of function 'usb_enable_lpm' [-Werror=implicit-function-declaration]
drivers/usb/core/hub.c: At top level:
drivers/usb/core/hub.c:3424:6: warning: conflicting types for 'usb_enable_lpm' [enabled by default]
drivers/usb/core/hub.c:3394:2: note: previous implicit declaration of 'usb_enable_lpm' was here
drivers/usb/core/driver.c: In function 'usb_probe_interface':
drivers/usb/core/driver.c:339:2: error: implicit declaration of function 'usb_unlocked_disable_lpm' [-Werror=implicit-function-declaration]
drivers/usb/core/driver.c:364:3: error: implicit declaration of function 'usb_unlocked_enable_lpm' [-Werror=implicit-function-declaration]
drivers/usb/core/message.c: In function 'usb_set_interface':
drivers/usb/core/message.c:1314:2: error: implicit declaration of function 'usb_disable_lpm' [-Werror=implicit-function-declaration]
drivers/usb/core/message.c:1323:3: error: implicit declaration of function 'usb_enable_lpm' [-Werror=implicit-function-declaration]
drivers/usb/core/message.c:1368:2: error: implicit declaration of function 'usb_unlocked_enable_lpm' [-Werror=implicit-function-declaration]
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: Chen Peter-B29397 <B29397@freescale.com>
This reverts commit 1996e6c572.
It turned out to not be needed, now that the real fix has been
committed.
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This branch simplifies and clarifies the dcache lookup, and allows us to
do certain nice optimizations when comparing dentries. It also cleans
up the interface to __d_lookup_rcu(), especially around passing the
inode information around.
* dentry-cleanups:
vfs: make it possible to access the dentry hash/len as one 64-bit entry
vfs: move dentry name length comparison from dentry_cmp() into callers
vfs: do the careful dentry name access for all dentry_cmp cases
vfs: remove unnecessary d_unhashed() check from __d_lookup_rcu
vfs: clean up __d_lookup_rcu() and dentry_cmp() interfaces
This teaches vfs_fstat() to use the appropriate f[get|put]_light
functions, allowing it to avoid some unnecessary locking for the common
case.
More noticeably, it also cleans up and simplifies the "getname_flags()"
function, which now relies on the architecture strncpy_from_user() doing
all the user access checks properly, instead of hacking around the fact
that on x86 it didn't use to do it right (see commit 92ae03f2ef: "x86:
merge 32/64-bit versions of 'strncpy_from_user()' and speed it up").
* vfs-cleanups:
VFS: make vfs_fstat() use f[get|put]_light()
VFS: clean up and simplify getname_flags()
x86: make word-at-a-time strncpy_from_user clear bytes at the end
To enable easy tracing of the location of log forces and the
frequency of them via perf, add a pair of trace points to the log
force functions. This will help debug where excessive log forces
are being issued from by simple perf commands like:
# ~/perf/perf top -e xfs:xfs_log_force -G -U
Which gives this sort of output:
Events: 141 xfs:xfs_log_force
- 100.00% [kernel] [k] xfs_log_force
- xfs_log_force
87.04% xfsaild
kthread
kernel_thread_helper
- 12.87% xfs_buf_lock
_xfs_buf_find
xfs_buf_get
xfs_trans_get_buf
xfs_da_do_buf
xfs_da_get_buf
xfs_dir2_data_init
xfs_dir2_leaf_addname
xfs_dir_createname
xfs_create
xfs_vn_mknod
xfs_vn_create
vfs_create
do_last.isra.41
path_openat
do_filp_open
do_sys_open
sys_open
system_call_fastpath
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sig.com>
Note xfs_iget can be called while holding a locked agi buffer. If
it goes into memory reclaim then inode teardown may try to lock the
same buffer. Prevent the deadlock by calling radix_tree_preload
with GFP_NOFS.
Signed-off-by: Peter Watkins <treestem@gmail.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
xfstest 270 was causing quota reservations way beyond what was sane
(ten to hundreds of TB) for a 4GB filesystem. There's a sign problem
in the error handling path of xfs_bmapi_reserve_delalloc() because
xfs_trans_unreserve_quota_nblks() simple negates the value passed -
which doesn't work for an unsigned variable. This causes
reservations of close to 2^32 block instead of removing a
reservation of a handful of blocks.
Fix the same problem in the other xfs_trans_unreserve_quota_nblks()
callers where unsigned integer variables are used, too.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
This makes cp_new_stat() a bit more readable, and avoids having to
memset() the whole structure just to fill in a couple of padding fields.
This is another result of me looking at code generation of functions
that show up high on certain kernel profiles, and just going "Oh, let's
just clean that up".
Architectures that don't supply the #define to fill just the padding
fields will still fall back to memset().
* stat-cleanups:
vfs: don't force a big memset of stat data just to clear padding fields
vfs: de-crapify "cp_new_stat()" function
This series sanitizes the interface to unmap_vma(). The crazy interface
annoyed me no end when I was looking at unmap_single_vma(), which we can
spend quite a lot of time in (especially with loads that have a lot of
small fork/exec's: shell scripts etc).
Moving the nr_accounted calculations to where they belong at least
clarifies things a little. I hope to come back to look at the
performance of this later, but if/when I get back to it I at least don't
have to see the crazy interfaces any more.
* vm-cleanups:
vm: remove 'nr_accounted' calculations from the unmap_vmas() interfaces
vm: simplify unmap_vmas() calling convention
If kzalloc() returns a NULL here, we pass a NULL to
xencons_disconnect_backend() which will cause an Oops.
Also I removed the __GFP_ZERO while I was at it since kzalloc() implies
__GFP_ZERO.
CC: stable@kernel.org
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Currently, the memory target in the Xen selfballooning driver is mainly
driven by the value of "Committed_AS". However, there are cases in
which it is desirable to assign additional memory to be available for
the kernel, e.g. for local caches (which are not covered by cleancache),
e.g. dcache and inode caches.
This adds an additional tunable in the selfballooning driver (accessible
via sysfs) which allows the user to specify an additional constant
amount of memory to be reserved by the selfballoning driver for the
local domain.
Signed-off-by: Jana Saout <jana@saout.de>
Acked-by: Dan Magenheimer <dan.magenheimer@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
There are two functions in this asm-generic file. Looking at
other arch which do not use the generic version, these two fcns
are within an #ifdef __KERNEL__ block, so make the generic one
consistent with those.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Add an ioctl to the /dev/xen/xenbus_backend device allowing the xenbus
backend to be started after the kernel has booted. This allows xenstore
to run in a different domain from the dom0.
Signed-off-by: Daniel De Graaf <dgdegra@tycho.nsa.gov>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
I have been looking over those patches for quite a
while. Adding myself officially as the maintainer
as agreed with Greg KH.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds support for the FALCON SoC. This SoC is from the FTTH/GPON SoC family.
Signed-off-by: Thomas Langer <thomas.langer@lantiq.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3814/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add support for OF. We also apply the following small fixes
* reduce boiler plate by using devm_request_and_ioremap
* sane error path for the clock
* move LTQ_RST_CAUSE_WDTRST to a soc specific header file
* add a message to show that the driver loaded
Signed-off-by: John Crispin <blogic@openwrt.org>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3810/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add devicetree and handling for our new clkdev clocks. The patch is rather
straightforward. .of_match_table is set and the 3 irqs are now loaded from the
devicetree.
This series converts the lantiq target to clkdev amongst other things. The
driver needs to handle two clocks now. The fpi bus clock used to derive the
divider and the clock gate needed on some socs to make the secondary port work.
Signed-off-by: John Crispin <blogic@openwrt.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alan Cox <alan@linux.intel.com>
Cc: linux-serial@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3809/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Implements OF support and add code to load custom properties from the DT.
The Serial To Parallel (STP) is found on MIPS based Lantiq socs. It is a
peripheral controller used to drive external shift register cascades. At most
3 groups of 8 bits can be driven. The hardware is able to allow the DSL modem
to drive the 2 LSBs of the cascade automatically. Newer socs are also able to
automatically drive some pins via the internal PHYs. The driver currently only
supports output functionality. Patches for the input feature found on newer
generations of the soc will be provided in a later series.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Patchwork: https://patchwork.linux-mips.org/patch/3839/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Implements OF support and convert to of_mm_gpio.
By attaching hardware latches to the External Bus Unit (EBU) on Lantiq SoC, it
is possible to create output only gpios. This driver configures a special
memory address, which when written to, outputs 16 bit to the latches.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Patchwork: https://patchwork.linux-mips.org/patch/3840/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move the 2 drivers from arch/mips/lantiq/xway/ to the subsystem and make them
buildable.
The following 2 patches will convert the drivers to OF.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Patchwork: https://patchwork.linux-mips.org/patch/3838/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Implement support for OF inside the lantiq PCI driver. The patch also splits
pcibios_plat_dev_init and pcibios_map_irq out into their own file to accomodate
coexistance with the upcoming pcie driver.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3806/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch unifies all clock generation and gating code into one file.
All drivers will now be able to request their clocks via their device.
This patch also adds support for the clockout feature, which allows
clock generation on external pins.
Support for COMMON_CLK will be provided in the next series.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3804/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As part of the conversion to OF we also implement pinctrl drivers. Previously
we used ltq_gpio_request() to set pinmuxing. This is now obselete and we can
hence drop the function.
Additionally we remove gpio_to_irq() from the gpio driver and move it to a
header file.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3801/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add support for irq_domain on lantiq socs. The conversion is straight forward
as the ICU found inside the socs allows the usage of irq_domain_add_linear.
Harware IRQ 0->7 are the generic MIPS IRQs. 8->199 are the Lantiq IRQ Modules.
Our irq_chip callbacks need to substract 8 (MIPS_CPU_IRQ_CASCADE) from d->hwirq
to find out the correct offset into the Interrupt Modules register range.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3802/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Before we are able to add OF support, we really want to drop all the bloat
needed to register all the platform devices.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3800/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On MIPS we want to call of_irq_map_pci from inside
arch/mips/include/asm/pci.h:extern int pcibios_map_irq(
const struct pci_dev *dev, u8 slot, u8 pin);
For this to work we need to change several functions to const usage.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-pci@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
Cc: linux-mips@linux-mips.org
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Patchwork: https://patchwork.linux-mips.org/patch/3710/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CONFIG_HID_WACOM must depend on CONFIG_LEDS_CLASS, otherwise
CONFIG_NEW_LEDS may be disabled.
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The dma_contiguous_remap() function clears existing section maps using
the wrong size (PGDIR_SIZE instead of PMD_SIZE). This is a bug which
does not affect non-LPAE systems, where PGDIR_SIZE and PMD_SIZE are the same.
On LPAE systems, however, this bug causes the kernel to hang at this point.
This fix has been tested on both LPAE and non-LPAE kernel builds.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
__alloc_contig_migrate_range calls migrate_pages with wrong argument
for migrate_mode. Fix it.
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Minchan Kim <minchan@kernel.org>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
This patch adds support for CMA to dma-mapping subsystem for ARM
architecture. By default a global CMA area is used, but specific devices
are allowed to have their private memory areas if required (they can be
created with dma_declare_contiguous() function during board
initialisation).
Contiguous memory areas reserved for DMA are remapped with 2-level page
tables on boot. Once a buffer is requested, a low memory kernel mapping
is updated to to match requested memory access type.
GFP_ATOMIC allocations are performed from special pool which is created
early during boot. This way remapping page attributes is not needed on
allocation time.
CMA has been enabled unconditionally for ARMv6+ systems.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Rob Clark <rob.clark@linaro.org>
Tested-by: Ohad Ben-Cohen <ohad@wizery.com>
Tested-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Tested-by: Robert Nelson <robertcnelson@gmail.com>
Tested-by: Barry Song <Baohua.Song@csr.com>
This patch adds support for CMA to dma-mapping subsystem for x86
architecture that uses common pci-dma/pci-nommu implementation. This
allows to test CMA on KVM/QEMU and a lot of common x86 boxes.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The Contiguous Memory Allocator is a set of helper functions for DMA
mapping framework that improves allocations of contiguous memory chunks.
CMA grabs memory on system boot, marks it with MIGRATE_CMA migrate type
and gives back to the system. Kernel is allowed to allocate only movable
pages within CMA's managed memory so that it can be used for example for
page cache when DMA mapping do not use it. On
dma_alloc_from_contiguous() request such pages are migrated out of CMA
area to free required contiguous block and fulfill the request. This
allows to allocate large contiguous chunks of memory at any time
assuming that there is enough free memory available in the system.
This code is heavily based on earlier works by Michal Nazarewicz.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Rob Clark <rob.clark@linaro.org>
Tested-by: Ohad Ben-Cohen <ohad@wizery.com>
Tested-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Tested-by: Robert Nelson <robertcnelson@gmail.com>
Tested-by: Barry Song <Baohua.Song@csr.com>
alloc_contig_range() performs memory allocation so it also should keep
track on keeping the correct level of memory watermarks. This commit adds
a call to *_slowpath style reclaim to grab enough pages to make sure that
the final collection of contiguous pages from freelists will not starve
the system.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Michal Nazarewicz <mina86@mina86.com>
Tested-by: Rob Clark <rob.clark@linaro.org>
Tested-by: Ohad Ben-Cohen <ohad@wizery.com>
Tested-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Tested-by: Robert Nelson <robertcnelson@gmail.com>
Tested-by: Barry Song <Baohua.Song@csr.com>
This patch extracts common reclaim code from __alloc_pages_direct_reclaim()
function to separate function: __perform_reclaim() which can be later used
by alloc_contig_range().
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Tested-by: Rob Clark <rob.clark@linaro.org>
Tested-by: Ohad Ben-Cohen <ohad@wizery.com>
Tested-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Tested-by: Robert Nelson <robertcnelson@gmail.com>
Tested-by: Barry Song <Baohua.Song@csr.com>
